Spl repair to Yamuna Vihar Bldg and provn of soakage and drain well and road from CSD to MT gate (path with interlocking tiles) at Old Cantt Prayagraj.

Amount

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Precast reinforced Cement Concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manhole covers etc. complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length bent to shape required incl cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius half brick thick wall built in CM (1:4) complete all as specified and directed.

M&L brick work with fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1: 6 complete all as specified and directed.

M&L brick work with sub class B old size brick straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed. (Except brick). Note: Bricks obtained from item No. 04 above shall be used.

Dismantling brick tiles any size laid bedded and pointed in any mortor complete all as specified and directed.

Demolition of mud in roofs any thickness and in any position and leaping over roof terrace, removing the demolished material to a distance exceeding 250 m & not exceeding 500 m and depositing where directed at a level n exc. 1.5 m above starting point, complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in roof padding finishing the surface fair & even complete all as specified and directed.

M&L for screed bed 10 mm thick in cement mortar 1:3 over roof slab mixed with water proofing compound ( WPC to be measured and paid separately) as per manufacturer’s instructions finished surface even & fair complete all as specified and directed.

M&L for cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and directed.

M&L for priming surface with approved bitumen primer confirming to [email protected] per Sqmm and applying hot blown grade 85/25 bitumen as per IS 702-1988 @1.2 Kg per Sqm and laying of polymeric water proofing membrane asphaltic polythene film of weight not less than 3Kg per Sqm with minimum 100mm side lap and 150mm along the length from down lamps to upward completely sealed with hot blown lamps complete all as specified and directed.

M&L for precast cement concrete tiles (factory made), size 25cm x 25cm x 25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished built with grey cement and no pigment over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bedding in cement mortar (1:4) complete all as specified and as directed.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick (400X400 square) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bedding in cement mortar (1:4) complete all as specified and as directed.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surface, skirting etc. and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and incl 10mm thick plaster in cement mortar (1:4) complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18- 20mm thick, laid over and including 20mm screed bedding in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 18- 20mm thick as in riser of steps, skirting, dado and pillar laid over and including 10mm thick plaster in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 20 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like over and including 20 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, making hole for gas pipe in pre-cast slab as well as stone slab in cooking platform complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc. complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl chequered tiling complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick walls in CM in 1:4, mixed with liquid water proofing compound as per manufacturer instruction, finished surface even and fair complete all as specified and directed. Note: WPC shall be measured and pair seperatly under respective items have in below.

Supply only Liquid water proofing compound of approved make complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on Brick/ Concrete surface, finished even and fair complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on concrete surface of ceiling complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of cement base paint on wall surface over a coat of primer complete all as specified and directed.

M&L for preparation of old plastered surface and applying two coat of cement base paint on walls over a coat of primer including complete removal of existing treatment complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of oil bound distemper on walls over a coat of primer including 1 mm thick wall care putty complete all as specified and directed.

M&L for preparation of old plastered surface and applying two coat of oil bound distemper on walls over a coat of primer and 1 mm thick wall care putty including complete removal of existing treatment complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks, etc., incl cleaning for refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl necessary clamp etc.complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl necessary clamp etc. complete all as specified and directed.

S&F in repair 110mm PVC (SWR) bends with access door complete all as specified and directed.

S&F 75mm PVC (SWR) bends any radius with acess door complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with acess door complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with acess door complete all as specified and directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair 75mm PVC floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 150 mm X 100 mm Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' and setting and jointing in cement mortar 1:1 complete all as specified and directed

S&F in repair stack clamps made out of 50mm x 5mm flat MS flat & 16mm dia round bar/stays including bolts & nuts and securing ends of stays for 100mm bore pipe complete all as specified and directed.

-ditto- all as per item No. 50 above but 75mm.

M&L for cutting chases pinning in, making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing, steps, cills, sunshades, selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting not exc. 10cm girth complete all as specified & as directed

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe complete all as specified and directed.

S&F GI tube 15mm bore medium grade with all fittings fixed to walls and ceilings or laid in floor all as specified and directed.

Refixing old steel tubing 15 mm dia and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed.

M&L 20mm bore GI tubing medium grade with all fittings and fixed complete to walls/ ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Refixing old steel tubing 20 mm dia and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed.

S&F in repair 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed.

S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F in repair Kitchen Sinks with drainage board, made of stainless steel l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling of 32 mm size complete all as specified and directed by Engineer-in-Charge.

S&F in repair 15 mm bore central hole basin mixer with 450mm long braided connection pipe (without popup) complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125 mm size with shower arm and fixed complete all as specified and directed

S&F in repair 15 mm bore stop valve fancy type chromium plated with long cup and shank (Concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repair 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repair 20 mm dia Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repair 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F in repair 40 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed to walls, ceilings or in floors etc. complete all as specified and directed.

S&F in repair kitchen rack plate of size 75 x 60cm, made out of 1.0mm thick stainless steel sheet of approved design and pattern complete all as specified and directed.

S&F in repair brass chromium plated Tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges including brackets fixed to wall complete all as specified and directed

S&F in repair stainless steel soap dish complete all as specified and directed.

Demolition of PCC of any description and in any position not specifically provided for complete all as specified and directed.

M&L for Treatment to sunken floor and sides as mentioned here after:- (i) Cleaning of RCC surface to sides and base slab dust free by using sand blasting with compressed air. (ii) application of one coat of glass fibre reinforced acrylic modified cementitious coating to sides and base of sunken over a base coat of glass fibre reinforcement primer (iii) 15 mm thick cement plaster on side and base slab of sunken part in cement mortar 1:3 mixed with appropriate integral water proofing compound . (iv) applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 Kg/Sqm on plastered surface of sunken sides & base. Note: All debris obtained from site will be thrown away out side Def Land by contractor at his own expense.

M&L for cement concrete 1:5:10 type E2 using 40mm graded stone aggregate as in sunken part of slab, complete all as specified and directed.

M&L for 25 mm thick cement concrete levelling course of type B-0 (1:2:4) finished complete all as specified and directed

S&F in repair fancy type drapery rod 20 mm dia stainless steel 304 grade including brackets, and ends caps (Lattoo) complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame), Area of opening not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down shutter of any description, area not exceeding 1.0 sqm each complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area of opening exceeding 1.5 Sqm but not exceeding 4.00 Sqm each complete all as specified and directed.

Dismantling boarding any desccription fixed in any position with nails or any other means complete all as specified and directed

S&F PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

M&L for preparation of old steel surface and applying two coats of synthetic enamel paint over complete all as specified and directed.

S&F 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and directed.

S&F 105x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and directed.

S & F factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as specified and directed by Eng-in-Charge.

S & F factory made wire gauzed panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm widthstuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wire gauzed shall be wrapped on an additional square 8mm MS solid tube and this tube shall be welded to MS tube. The wire gauge shall be stretched to tighten firmly. PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 150mm aluminium handles, cast type, anodised complete all as specified and directed.

S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed

S&F for aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) frame for doors, windows with one or more rebates joining cleat for fixing etc complete all as specified including concealed type lock for all three shutters complete all as specified and directed.

M&L for powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings for each leaf such as peg stays 150mm long (01 No.) hinges type B-21 100mm long (02 No.) suitable handle (01 No.) complete all as specified and directed.

M&L for MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for 4.8 mm thick frosted sheet glass ordinary quality and glazing with beading not exc. 0.5 sqm in each pane complete all as specified and as directed.

S&F 150mm long, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate fixed in repair complete all as specified and directed.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring complete all as specified and directed.

S&F 18 mm thick celuka ply of single side prelam/Rigidlam colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides, top and bottom and shelves inside the cabinets complete all as specified and directed (Density - 575 to 600 Kg/CBM)

S&F 18 mm thick celuka ply (PVC) of plain white(Matt finish) colour fixed with screws, solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete all as specified and directed. (Density - 575 to 625 Kg/CBM)

S&F continuous (piano) hinges, Stainless steel of width 40 mm complete all as specified and directed.

M&L for 1st quality non skid coloured ceramic Heavy duty parking tiles area of each tile not exceeding 0.11 Sqm 10 mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including including 15 mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for 75 mm thick cement concrete type C-2, 1:3:6 (using 40mm graded stone aggregate) as in floor / sub base finished cement concrete surface even and fair, complete all as specified and directed.

Excavating over areas not exc. 1.5 Mtr deep and getting out in loose soil complete all as specified and directed.

All as per item No 111 above but exc 1.5 mtr not exc. 3.00 mtr complete all as specified and directed.

All as per item No 111 above but exc. 3.00 mtr not exc. 4.5 Mtr complete all as specified and directed.

M&L for PCC(1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for brickwork with fly ash bricks curved on plan n exc 6.00 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for brickwork with fly ash bricks, old size straight or curved on plan exceeding 6 metre mean radius, built in CM 1:6, one brick thick as in honey comb wall complete all as specified and directed.

M&L for Reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in band beam complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs complete all as specified and directed.

M&L for loose filling of broken bricks of guage 40 to 80 mm in soakage pits, soakage wells complete all as specified and directed.

M&L for formwork to suspended slabs such as roof slabs, floor slab sand similar work complete all as specified and directed.

M&L for formwork to sides of slabs, thickness of slab exceeding 5cm but not exceeding 10cm complete all as specified and directed.

Returning in, filling including spreding, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and direcetd.

Removing excavated material not exceeding 50 mtr, depositing where directed at a level not exceeding 1.5 mtr above the starting complete all as specified and direcetd.

M&L for surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft and loose soil complete all as specified and directed.

M&L 100 mm thick plain cement concrete type -D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified and direcetd.

M&L sand filling under floors or in foundations incl watering and consolidation complete all as specified and direcetd.

Machine pressed precast conctete interlocking paver block with grey cement & pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade, complete all as specified and direcetd.

M&L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) in copings, kneelers, apex stones, bed plates, etc incl necessary formwork complete all as specified and direcetd.

M&L for hardcore of broken stone or boulder of gauge not exceeding 63mm deposited spread levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Taking down copper/aluminium point wiring [light point, fan point or socket point or power] including removal of battens, pipes, plug sockets, switches, shades, ceiling roses, light fittings etc complete and making good disturbed surface to match the exisitng, complete all as specified and directed.

Taking down main switches, distribution boards and cut outs of any capacity along with the exisitng boards and removing the same from site and making good disturbed surface or portion of walls complete all as specified & directed.

Taking down carefully sub main wiring of any numbers of wire on wooden batten or surface conduit or concealed conduits / casing caping any type complete all as specified & directed.

M&L for point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including 20mm dia rigid PVC conduit 'medium grade' ISI marked, all conduit accessories, concealed pressed steel terminal box of required size ( factory made, not less than 1.6 mm thick) duly painted inside and outside with two coats of black bituminous paint over a coat of red oxide primer, 3.0 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc, including green colour as continuous earth wire of same size & type, connected to earth dolly as required at site and including chases cutting and making good the disturbed surface, finishes to match the existing surface, for One light / fan / bell / exhaust fan point, controlled by one one-way 5Amp switch complete all as specified and directed.

All as per item No. 134 above but for One 5 pin, 5 Amp socket outlet point on an independent board.

All as per item No. 134 above but for One 5 pin, 5 Amp socket outlet on the same board with other switches

All as per item No. 134 above but for one bell/buzzer point controlled by one bell push single pole one way

All as per item No. 134 above but for one light point controlled by two two-way switches.

All as per item No. 134 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, two way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Socket outlet, 2 in 1, 5 pin 5/6 Amp, 230 volts, flush type complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F Socket outlet, 2 in 1, 6 pin 15/16 Amp, 230 volts, flush type complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with 10W LED bulb and back plate suitable for batten fittings complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F bell push piano, flush type, single pole, one way 5/6 Amp 230 volts complete all as specified and directed.

S&F electric bell ding dong type AC 230 Volts, 50 Hz single pole complete all as specified and directed.

S&F ceiling fan regulator, electronic, rotary step type suitable for 1200/1400 mm sweep ceiling fan complete all as specified and directed.

S&F sheet metal enclosure (Distribution board or FB) for MCBs, double door type, single pole and neutral 8 way 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete (without MCB but with enclosure blank plates for unused way) complete all as specified and directed.

S&F MCB Single Pole and neutral, 6 to 32 Amps 240 volts, 10KA breaking capacity, convenient to 'C' Curve complete all as specified and directed.

S&F MCB Single Pole, 6 to 32 Amps 240 volts, 10KA breaking capacity, convenient to 'B' Curve complete all as specified and directed.

S&F 1 x 9W LED Mirror light fitting, LED 6000K, Decorative Indirect up-down light for mirror and as wall light application with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp complete all as specified and directed.

S&F 1 x 10W LED Bulk head light fitting, LED 600 lumen, enclosed in polycarbonate body, weather proof, LED light fitting fixture with co extruded polycarbonate body, environmental friendly, energy efficient complete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp complete all as specified and directed.

S&F 1 x 18W LED wall mounted tube light fitting, LED 6000K, Decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including LED lamp complete all as specified and directed.

S&F decorative wall light fixture made up of Polycarbonate, suitable for B-22 type lamp polycarbonate body, weather proof, LED light fitting fixture with co extruded polycarbonate body, environmental friendly, energy efficient complete with all accessories, prewired and making connection with and including three core flexible copper cable of size 23/0.0076 from ceiling rose to connector of required length including 10 Watt LED lamp complete all as specified and directed.

S&F 36 Watt road lighting luminaire with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and Streets, 50% Energy Savings, IP66 Protection PC and FG Cover, High Impact Resistance complete including LED Lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20 m long made to shape and fixed to existing pole or bldg by means of 2 Nos mild steel flat iron 40x6mm clamps with suitable size bolt, nuts & washers and connecting with three core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick directly buried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below the ground level connected to GI earth wire 4mm dia by means of bolts nuts check nuts and washers of galvanised iron at 2 points & GI pipe 15 mm bore light grade for protection of earthing wire PCC chamber 1:3:6 (type C-1) using 20mm graded stone aggregate, watering pipe 20mm bore light grade, funnel with wire mesh, 50 mm thick cover of RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8 mm MS bars at 150 mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No. 3 of MES SSR part-I and including excavation & earth work & connecting the earthing point/equipment and testing complete all as specified & directed.(Note- The cost of GI wire and protection pipe upto test point shall be included in above quoted rates.)

S&F sub main wiring with two single core FRLS PVC insulated unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area FRLS PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 20mm dia 'medium grade' PVC concealed conduits and fittings, including taking down existing sub main wiring complete all as specified and directed. NOTE: One unit length shall measured as two run of main wire and one run of conduit & earth wire

Taking down carefully ceiling fan/ exhaust fan by disconnecting all electrical connection and refixing the same including electric connection wire 3 core 23/0.0076 copper conductor including one coat of synthetic enamel paint and marking MES no with paint complete all as specified and directed.

Taking down carefully existing gyser by disconnecting all electrical connection and refixing the same including electric connection wire 3 core 23/0.0076 copper conductor including applying one coat of synthetic enamel paint and marking MES no with paint complete all as specified and directed.

S&F two pin and earth plug and socket with 1 MCB single pole 20 to 32amps C series 10KA in sheet metal enclosure and connecting complete all as specified and directed.

Supply, laying, testing XLPE cable Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3½ core complete all as specified & directed .

Excavation in trenches/Pits in any type of soil(soft/loose/hard/ dense soil), n.exc. 1.5M wide and n.exc. 1.5M deep and getting out complete, all as specified & directed .

Returning filling of excavated earth including spreading, leveling and well ramming in layers n.exc. 25cm thick complete all as specified & directed.

Removal of surplus excavated material to a distance n.exc. 50 Mtr and depositing where directed at a level n.exc. 1.5 Mtr above starting point complete all as specified & directed

M&L for providing old size sub class 'B' bricks laid perpendicular to the cable abutting each other complete all as specified and directed.

Supply and spreading clean and dry sand (unwashed) in trenches around the cable for cushioning complete all as specified & directed

Supply and lying GI pipe light grade 50mm in trench wall/post etc per cable protection complete all as specified and directed

Hi-Tech Constructions

KRISHNA BAHADUR

Shivagya Engineering

Minakshi Construction

M/S JAI DURGA CONSTRUCTION

vs construction

shweta constructions