0707 Floating pump

0707 Floating pump Specification--PUMP AND ENGINE SPECIFICATION Casing-Powder Coated Anodized Aluminum as per IS 617 Impeller -Bronze impeller 3. Engine specification. Engine shall meet applicable environmental norms and emission standard of Govt. of India. 4 stroke air cooled petrol engine Power Output -Not less than 5.9 HP Ignition System -Transistorized Magneto Starting System-Recoil Type of Pump -Single Suction, Centrifugal Outlet -63 mm instantaneous Water discharge-Not less than 900 I or min Delivery head-10 Meter Min Water Depth -25 mm of Water Discharge of solid-up to 15 mm size Automatic Float controlled throttle 4. FUEL TANK Appropriate for continuous run of at least 1 hrs and should equipped with fuel gauge. 5. FLOAT ASSEMBLY HDPE Shell or Fiber glass with polyurethane foam. 23Outlet -63 mm instantaneous Water discharge-Not less than 900 I or min Delivery head-10 Meter Min Water Depth -25 mm of Water Discharge of solid-up to 15 mm size Automatic Float controlled throttle 4. FUEL TANK Appropriate for continuous run of at least 1 hrs and should equipped with fuel gauge. 5. FLOAT ASSEMBLY HDPE Shell or Fiber glass with polyurethane foam

0707 High Expansion Foam Generator Specification - High expansion foam generator shall driven by water pressure and used for coverage for large spill of hydrocarbon liquids,total flooding of voluminous enclosure such as cable ducts and in accessible locations. It should be light weight, compact, suitable for groundoperation and easy movement. It should have arrangement for smoke extraction also. It should have pressure gauge of suitable rating at inlet for measuring pressure of water flow. A carrying handles and wheels should be provided for easy and smooth carriage.Body -SS or FRP Materials to be specified by Indentor 2. Nozzle -Gun Metal 3. Foam Screen -SS 4. Piping and Foam Inductor -Light weight material with anti corrosive treatment 5. Fan -Fibre reinforced Plastic - FRP-or SS-Material to be specified by Indentor- 6. Coupling -Gun Metal 7. Foam Duct -Nylon or Polythene - Material to be specified by Indentor- 6.0 Dimension of the Body - shell-and attachment- 1. Depth -450 - 500 mm 2. Width -900- 950 mm 3. Height -900- 1000 mm 4. Foam duct -10 meter Long 5. Smoke duct -10 meter long 6. Coupling Diameter -63 mm - instantaneous type- 7. Maximum unit weight -50 Kg

0707 Aluminium Fire Suit Specification - The suit shall allow the wearer to expose himself and withstand point source approximately at 900 degC for 4-5 minutes, 700 degC for 15 minutes and 500 degC for 5 hours without adversely affecting the wearer .The fabrication of fire proximity or approach suit shall be made out of non-flammable, light weight, non-toxic flexible and heat reflecting material. The fabric shall be of impermeable aluminized coated oxidized penotex carbon fiber and shall have thermal insulation lining capable of resisting high temperature not less than 900 degC.max.wt-9.0 kg.

0707 Suction hose 100mm Specification - Suction Hose synthetic of 100 mm internal dia and length 2.5 mtr. Confirming to IS 3549 latest revision. It must be fully wire embedded suction Hose, which can be used from suction side of the pump from source to pump in-let. The suction hose mostly binded with copper wire with ISI Marked male and Female threaded coupling as per IS 902 - latest revision-and shall have 04 lugs. The hose shall be subjected to an internal hydraulic pressure of 8 Kg or Cm2 for a period of three minutes and there shall be no sign of leakage or failure. The working vacuum shall be down to 635 mm of mercury without collapse. Coupling must be tested for hydraulic pressure test at 21 kg or Cm2 for a period of 02 Minutes. The suction hose must be protected against oil, Fungus, chemicals, acid and alkalis.

0707 Smoke blower cum Exhauster. Specification - It should be portable, high output smoke exhauster, Petrol Driven Engine - 5.5 HP-and should be of size 18 inch or above. 2. It should be able to provide both positive and negative pressure ventilation to serve dual application i.e. as a Blower as well as suction for clearance of smoke or gases even in confined or closed non ventilated areas 3. The exhauster should be compact in dimension or size and should not measure more than 20 - Height-x 20 - Width-x 15 - Depth-with a tolerance of + or -10 percent so that it can be easily placed in the fire tender compartment if so required. 4. The exhauster unit should be light in weight and weigh less than 35 kg with a tolerance of + or - 10 percent . 5. The Exhauster should have high output airflow for effective de smoking operations. 6. The fan size should be 18 diameter with many turbo blades to generate strong air force. 7. The dimensions should not exceed 18 inch in depth, 24 inch in width and 24 inch in height BLADE - - 18 diameter assembly should made up of aluminium or air flex fiberglass reinforced polyamide blades FRAME - - It should formed and welded sheet metal construction with powder -coat finish. GRILLE - - should Continuous Circular Wound External -Weld Steel Wire with 4 Tie Points for Additional Safety - Steel is Zinc-Plated with a Clear Chromate Finish

0707Stretcher Specification - STRETCHER Sl Parameters Value 1. Unfolded Size of the stretcher - L X W X H -Not less than 201 X 53 X 13 - cm-with tolerance of +- 2 mm 2. Number of folds which can be made Not less than 02 3. Material of the Stretcher frame Aluminium or Powder Coated Mild Steel 4. Material of the Support bed of the foldable stretcher Vinyl Coated Nylon Fabric or Tetron Canvas 5. The foldable stretcher shall fold lengthwise and cross wise and shall fold flat for compact storage and asy transportation Yes 6. Support bed of the foldable stretcher shall be stain and water resistant and easy to clean and antifungal Yes 7. Foldable stretcher shall have aluminium feet to prevent stretcher bed from touching the floor Yes 8. Aluminium poles shall have rubber hand grips to keep a firm grasp on the stretcher Yes 9. Minimum Load carrying capacity of the Foldable stretcher No less than 160 kg 10. Weight of the foldable stretcher Not more than 20 kg 11. Foldable stretcher should have patient restrain strap with double locking Quick release safety Buckets Yes 12. Vertical hoisting sling to be provided Yes

0707Lifebuoy Specification - 2. Technical requirement- - a-The Lifebuoy shall be IRS approved. - b-Lifebuoy shall be made up of, high visibility, impact resistant orange PE material filled with high density soft polyurethane - PU-foam which gives high floatability. - c-Lifebuoy shall be provided with a grab line attached at four equally spaced points. - d-Lifebuoy shall have Solas Retro- Reflective tape stuck at four equally spaced places. - e-Lifebuoy should be suitable for major application is rescue during floods and sea mishaps. - f-Lifebuoy should have OD 71 +- 1 cms,ID 45 +- 1 cms. - g-Lifebuoy should have buoyancy more than 17 kg. - h-Lifebuoy shall be moisture proof and non-inflammable. 3. Approvals- - a-Lifebuoy shall be IRS approved. - b-Lifebuoy shall conforms to SOLAS 74 as amended Reg. III or 4,III or 7.1,III or 34,x or 3 LSA Code Reg. I or 1.2 and II or 2.1.1 IMO Resolution MSC.81 - 70 - , MSC. 200 - 80 - , MSC.97 - 73-8.1,8.3.

0707Life jacket Specification - Technical requirement- - a-It shall be made up of high visibility nylon orange coloured cloth filled with high density soft polyethylene foam to provide high floatability. - b-Jacket shall be provided with suitable plastic Quick Lock Buckle and Velcro for tightening. - c-IRS approved water activated life jacket light should be provided with life jacket. - d-Whistle shall be attached with Jacket and SOLAS approved Retro- Reflective tape stitched at visible locations covering a total area not less than 400cm. - e-It shall be suitable for major application is floods and sea or river mishaps. - f-Life jacket shall have size not less than 68 x 42 x 10 cm. - g-Floatability shall not be less than 16.5Kgs. - h-Weight of jacket shall not be more than 750gms - + or -100gm - .

0707 Celling hook Specification - SPECIFICATION OF FIRE HOOK STANDARD IS 927 - 2008 The function of fire hook is to pierce celling to allow the water on the upper floor to drain away, to pull down thatched roofs or roofs made out of matting, pulling out bales and bags of various commodities from a distance,opening and closing down of doors and various similar jobs TECHNICAL FEATURES - Material shall Steel to be used for hook conform IS 2004 - 1978 - handle shall be made of bamboo of length not less than 3 m - The edges shall be well shaped and finished - Forgings shall be free from seams ,burrs cracks and other surface defect - Hook shall be treated with suitable anti corrosive paint - Hook shall be engaged to horizontal bar and weight of 140kg shall be applied vertically to the handle .The test hall be repeated ten times .The hook shall not bend and or or dent during the test. - Standard IS 927 - 2008 MARKING Each hook shall be Cleary and permanently marked with the following information - Manufacturer s name or trade mark - Size of handle - Year of manufacture - Marked with standard mark NOTE - The equipment should be procured from the manufacturers - Manufacturer needs to have all test or evaluation facility in house failing which the test evaluation should got done from Govt. lab or Govt. approved NABL accredited lab only - PRE DISPATCH INSPECTION-PDI clause is mandatory and to be incorporated at the time of indent of above fire equipment. The CISF representative for inspection or PDI shall be detailed by Fire Directorate New Delhi

STANDARD IS 8096 - 1992 Fire beaters are often used for putting off small fires such as wild grass, shrubs, dry vegetation, hay, plastic, coal which can be easily put out by beating and smothering. This piece of equipment finds much application in rural areas and in those places where there is a scarcity of water COMPONENTS 1. Handle - i-The handle shall be made of solid bamboo having 1800 mm length and 30 + 5 mm diameter or of some alternative material of heat insulate properties provided. The handle shall be finished smooth. - ii-The handle before fitting into the socket made in shank shall be liberally swabbed with termite resistant composition comprising 10 percent solution of acid-chromate composition in water. It will then be allowed to dry for at least 24 hours. - iii-The free end of the bamboo handle shall be protected from disintegrating by fitting with a hollow close ended cap made of chrome plated Mild steel or aluminium. The protective cap shall have knurling made on its outer surface to enhance grip At least 5 mm of the round edges of this knurled protective cap shall be chamfered all round at 45 degree to reduce sharpness 2. Blade The blade of the fire beater shall consist of a rectangular piece of expanded mild steel or steel or steel wire mesh measuring 452 mm x 352 mm, covered fully on both sides with stretched fire resistant canvas olive green in colour placed between two frames and securely fixed in position with hexagonal nut-bolts using spring washers all-round the frame The two pieces frame shall be made of 1 mm thick mild steel. The width of frame shall be 30 mm. The shank portion of the blade shall also be in two pieces made of 1 mm thick spring steel. The frame shall be welded at diagonals as per IS 819-1957 ASSEMBLING The blade so made shall be fixed with bamboo handle through a two piece shank. The socket part of the shank shall be tightly screwed to the bamboo handle by two bolts, nu