PROVISION OF ROOMS FOR SINGLE OFFICERS ACCN AT DGRR MESS AT PRATAP CHOWK, AADN/ALTN TO DOORS FLOORING AND OTHER CONNECTED B/R AND E/M WORKS AT BLDG NO P-22 MALL ROAD AND IMPROVEMENT OF TOILETS, BATH AND KITCHEN OF T-4 PARADE ROAD UNDER GE (EAST)

Amount

Surface excavation not exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil, complete all as specified and directed.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cable etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as foundation filling in mass concrete, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide complete all as specified and directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Description all as per item No 9 but but 8mm dia as in stirrups.

M&L for reinforced cement concrete M-25 (Design mix) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix) as in Columns, pillars, piers, posts and struts etc. all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc. all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, chhajja,deck slabs and in shelves and the like etc. all as specified and directed.

Providing and applying the plaster with single component ready to use Polymer modified repair mortar capable of applying 15mm average thickness in single layer and finishing with trowel with a bond coat : SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area complete all as specified and as directed. Make: Smart Care (Asian Paints) or equivalent in Sika/ Fosroc/ Berger/ STP. Note : The application shall be executed on any type of surface and on horizontal/Vertical areas.

M&L for APP based polymeric membrane with mineral granules on top surface, minimum weighting 3 kg/Sqm and minimum 3 mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm with bitumen primer and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.6 kg/sqm at overlapping joints with a over lap of 75mm at the sides and 100 at the ends complete all as specified. Note: the water proofing treatment shall be carried out by the manufacturer or their authorised applicators.” Make- Asian/ Stp/ IWL Notes- 1. The Work Shall be executed through authorized applicator of manufacturer 2. Authorized applicator shall be approved by GE before starting of work 3. All material shall be procured directly from the manufacturer.

S & F for ceramic cool roof glazed Heat Resistant Terrace Tiles (300 mm x 300 mm x 10mm) on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, complete all as specified. Make: Johnson/ Orient bell or equivalent

M&L for Brick work with sub class 'B' bricks straight or curved on plan to any radius built in CM 1:6 complete all as specified and directed.

Returing, filling in incl spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavated matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils, complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as demp proof course and incl provision of Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50kg per sqm, complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 75mm thick plain cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified.

M&L for hardcore of broken bricks of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) of size 300mmx300mm or 400mmx400mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M & L for glazed ceramic tiles in vertical surface of size 300mmx600mm and 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for Vitrified coloured tiles (light shade) 8-10mm thick (square/rectangular) polished, area of each tile exceeding 0.36 sqm but not exc 1.00 sqm each in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and as directed.

M&L for Vitrified coloured tiles (any shade) 8-10mm thick (square/rectangular) polished, area of each tile exceeding 0.36 sqm but not exc 1.00 sqm each in dado, skiritgs etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

M&L for Rendering 15 mm thick in cement mortar 1:4 on fair face of brick work/ concrete surfaces with water proofing admixture finished even and smooth without using extra cement, complete all as specified and directed.

PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) in surface channels and drains, complete all as specified and directed.

M & L for extra for forming fair finished drain or channel 45 cm inner grith in cement concrete , using extra cement, including forms, moulds, mi-tred/ stopped ends etc, complete all as specified and directed.

PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in benching for manholes, bands, coping, bed plate etc with slightly chamfered or rounded angles including necessary from work, if any, and finishing exposed surface even and smooth without using extra cement complete all as specified & directed.

M&L for Rendering 5mm thick in cement mortar 1:3 as in ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surface, finished even and fair, complete all as specified and directed.

S & F for Factory made UPVC (white/Off white colour) sliding window, three track made out of extruded profiles with wall thickness of members as 2.3mm (1-0.2mm). Window profile with hollow section with multi chamber frame (60mm x 62mm) sash bars (42mm x 67mm). Sliding inter lock (one in each shutter 45.5mm x 28mm). Glazing head (24.5mm x 16mm) members will be mitred, cut and fusion welded in all corners including drilling of holes for fixing hardware and drainage of water. Making arrangement for fixing of hardware, EPDM gaskets 1.2, 1-0.2mm thick galvanised steel frame (30mm x 21.50mm). Sash bars (30mm x 18mm) profile to be inserted in required profile frame and will be fixed to the wall with 8mm x 100mm long fastners. Hardware : Touch lock to be of Zinc alloy (white powder coated), Steel roller system including 5mm thick glazing with selelcted quality glass, Aluminium track on bottom rail to be of hree track sliding frame, wool pine for sliding sash and interlock, complete all as specified and as directed. complete all as specifed and as directed. (Note:The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)

Description all as per item no 35 above but wire mesh door shutter all as per specification.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over and including 2mm thick wall care putty complete all as specified and as directed.

S & F plain gypsum board panel 12 mm thick on false ceiling (including any design/ cob design as required & pattern as approved by GE) with and including necessary GI frame work for seamless ceiling used with 'T' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm complete all as specified and directed.

M & L for preparing newly plastered surfaces of wall incl preparation of surfaces and applying two coats of acrylice emulsion paint over a coat of interior primer and 2-3mm wall care putty (JK or Birla) on wall surfaces complete as specified and directed.

Description all as per item no 40 above but in ceiling, complete as specified and directed.

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed.

Description all as per item No 42 above but 20 mm bore.

BLANK

S & F Vitreous china single Piece floor mounted WC With PP Soft Close Seat Cover, Hinges, with cistern & Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 360x730x740 mm, S Trap- 300 mm including connection to drain pipe with all fitting and fixture complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. SLS-WHT-6851S300PP or equivalent in Marc / Kohler )

S&F fancy type chromium plated 15 mm dia stop cock/angle cock/ angle cock, cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle, flinch screwed both ends for iron or for union, complete all as specified and directed.

S&F PVC connection 15 mm bore and 45cm long with washers, complete all as specified and directed.

S&F fancy type chromium plated bib taps brass cromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S & F ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :- (a) Vitreous China Wash Hand Basin 810mm x 500mm with CP grating and CP bottle trap. (b) Base Cabinet 780mm x 485mm x 460mm. (c) Side Cabinet 300mm x 250mm x 1800mm. Make : Hindware - Cat Part No. 70089 or 70084. Make : Kohler : Cat Part No. K-31602IN-E63

S&F of CP towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190 gms) fixed on walls, complete all as specified. (Make: Jaquar/ Marc/ Kohler)

S&F Hat and coat hooks, set of six, solid body of brass, 175mm to 250 mm complete all as specified and directed.

Supply & fix 3-in 1 wall mixer with provision of over head shower and hand shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed. (Make Jaquar Florentine FLR-CHR-5273 UPR/ Pearl GPR-884/ CERA- F1017401)

S&F Brass chromium plated shower rose 200mm size with 600mm long rod size all as specified and directed (Make: Jaquar/ Cera/ Pearl or equivalent)

S & F 65 x 95 mm rectangular shape single flow hand shower ( body & face plate stainless with ABS body in chrome finish) with rubit cleaning system including flexible pipe and fixed complete all as specified and as directed. (Make : Jaquar cat part No HSH CHR 1657 or equivalent in Jaquar / Marc / Kohler )

S&F Stainless steel grating 100mm square type with centre hole of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

S&F Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron, complete all as specified and directed.

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S & F SS soap dish, , complete all as specified and as directed. (Make - Jaquar/ Marc/ Kohler)

S&F CP health faucet with 8 mm Dia, 1.5 Meter Long Flexible Tube & Wall Hook completed all as specified Make : Jaquar Cat part No. ALD-CHR-573 and equivalent in Marc/ Kohler)

S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 45 cm long complete. (Make: Jaquar/Marc/Kohler)

S&F Brass CP Basin Single lever mixer central hole for making hot and cold water fixed as per manufacturers manual with long shunk and cup washers, screwed both ends suitable for 15mm bore GI Pipe joints to GI pipes or unions, complete. (Make : Jaquar Continental CON-CHR-167KNB or equivalent in Marc/Kohler)

S&F Hubless CI pipes of 100 mm nominal diameter (single socketed) in any length with rubber ring joints and clamps including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

Description all as per item No. 62 above but 75mm size.

S&F Hubless CI 100mm dia (single T) or unequal provided with access door complete all as specified and directed.

S&F 100 mm bore CI hubless bends/shoes any radius complete all as specified and directed.

Description all as per item No. 65 above but 75 mm bore.

S&F in PVC (SWR) 110 mm Nahani trap with grating including jointing to waste pipe in cement concrete, complete all as specified and directed.

S&F in PVC (SWR) floor trap, 75mm dia plain including jointing with solvent cement with grating including jointing to waste pipe in cement concrete, complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and forming benching as required for 150mm dia pipes complete all as specified and directed.

S&F toilet paper holder of of brass, chromium plated fixed to walls with chromium plated(CP) brass screws, complete all as specified and as directed.

S & F Precast RCC manhole covers 75 mm thick medium duty conforming to IS-12592 complete all as specified and as directed.

M&L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested, in cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) for 150mm dia pipe, complete all as specified and as directed.

S&F DWCPE (SN8) nominal size 150 mm (internal dia) mm including all fixing accessories or fittings like socket/spigot joint with elastomeric sealing ring, rubber ring, SILAID rubber lubricants required for laying of pipes, laid in trenches, complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80 mm thickness of M-40 Grade with grey cement and pigment cover and inclduing 50mm thick sand cushioning complete all as specified and directed

M & L Heavy duty vitrified external designer floor tiles, parking tiles etc any colour, shape and size upto the area of 0.18 sqm each tile thick , set & jointed in neat cement slurry and pointed flush with grey cement and pigments to match colour of tiles in floors over 15 mm thick screed bed or bedding layer in cement mortar 1:4, including dismantling of existing floor tiles of any type and in any position complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based Corrugated Steel Sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

S& F Mild Steel work in rafter , purlin, and other connected work including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and as directed.

S&F M S plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, complete all as specified and as directed.

M&L for two coat of synthetic enamel paint (finishing coat) over one coat of red oxide primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces, complete all as specified and as directed.

M & L with fabrication & fixing to horizontal & vertical shelves/ partations /sides/ top/ bottom/back sides etc for Modular kitchen cabinate/ wardrobe/ cupboard/drawers made out of 17/18 mm thick WPC boards with white laminated colour on both sides, of approved quality including paste to all exposed edge by edge Banding Tape including provision of cabinet for keeping baskets/ drawers etc all as specified and directed. (Design and pattern as approved by GE). (Make :Action tesa or equivalent as approved by GE)

Construction of soakage well 2.40m internal dia and 3.00m effective depth including excavation in any type of soil,returning filling & removal , PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in footing, brick honey comb/ solid brick masonry in cement 1:4, RCC (M-25 design mix) including TMT steel reinforcement in slab including mainhole cover , filled with brick bats including intercepting chamber screen chamber and disposal of soil, complete all as shown in drawing No DZ/1124R, Sheet 1/1 dt 14.05.2024 (Revised) specified. Note : 1. During excavation if unexpected water is encountered, the same shall be bailed out / de-watered by the contractor mechanically or manually without any extra cost. 2. The excavated surplus soil shall be removed to a distance exceeding 50 mtr and not exceeding 100 mtr and deposited where directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) any type and size exc. 1.5 Sqm but not exc. 4.00 Sqm each complete all as specified and directed.

S & F Anodised aluminium frame for doors, windows, ventilators, partations, AC provision window frame with or without three track, three track window frame etc with Powder Coating (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified. (Note : Design and pattern for any type window/door/ventilator etc frame as required as approved by GE )

S & F Anodised aluminium door shutters, powder coating of any colour, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, 150mm size AL handles 2 Nos in each door, 100mm size AL hinges 03 each shutter, anodised aluminum snap beading screws etc. complete all as specified. (Note : Quoted rate shall deem cost of 5mm thick Glass / SS wiremesh/ 12mm thick partical board/ 4mm thick ACP board etc).

M&L Virified Ceramic tile (light shade) 15 mm thick (square/rectangular) polished) , area of each tiles 2400 x800mm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick rendering in CM 1:4 including dismantling of the existing tiles complete all as specified and directed

Description all as per item no 87 as in in skirting and dado set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10 mm thick rendering/ backing coat in CM 1:4 complete all as specified and directed.

S & F plain gypsum board panel 12 mm thick on false ceiling ( including any design/ cob design as required & pattern as approved by GE) with and including necessary GI frame work for seamless ceiling used with ' T ' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm and including dismantling of walls and celing existing old board (fibre pulp.insulation etc)or insulation boards/slabs/blanks any thickness including cover fillets etc including two coat of OBD over a coat of putty, complete all as specified and directed.

Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core etc. to store and rubbish not exc. 50m, complete all as specified and as directed.

Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete all as specified and as directed.

Making good under cills over arches, lintels and bressummers.ncluding all pinning when necessary, complete all as specified and as directed.

M & L for preparation of internal old decorated brick/ concrete /plastered/un-plastered surfaces/pointing/un-pointing surface of walls, ceiling pillers, cornices etc by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil and greasy spots including cracks/ holes in surface filling with white putty etc to receive further, any type of treatment as like white wash/ colour wash/ OBD/internal & external emulsion paint/acrylic distemper etc, complete all as specified and directed.

M & L for two coat of distempering with 1st quality acrylic emulsion (ready mixed) (interior) of approved manufacturer over & incl 1-2mm thick water proof wall care putty and one coat of primer after sand scrubbing the putty, of required shade and colour, as per manufacturer's specification and using roller brush, applying on any type of prepared surface of walls, ceiling, pillers, cornices etc, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including cut reinforcement required to facilitate demolition upto and including fourth story bldg and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving not exe 15cm thickness (below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

Dismantling of PVC water tanks exc 500 liters but not exc 1000 liters capacity of any condition or type complete all as specified and directed.

Dismantling of PVC water tanks not exc 500 liters capacity of any condition or type complete all as specified and directed.

Dismantling of PVC pipe up to 100 mm bore complete all as specified and directed.

Dismantling of PVC pipe up to 75 mm bore complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

Description all as per item No. 105 above but 20 mm bore.

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed.

Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4) Ty B-1 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span etc. all as specified and directed.

M&L for reinforced cement concrete (1:2:4) Ty B-1 using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, chhajja,deck slabs and in shelves and the like etc. all as specified and directed.

M & L for 16 to 18 mm thick granite (Z-black colour or any suprior quality/colour as approved by GE) table rubbed and polished in jambs, pillars, window cills, cooking platforms, floor , steps, serving counters etc and like over and including 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching, moulding and diamond polishing, complete all as specified and as directed .

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Make 'Rajshree or equvelent'

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including 3 Nos stainless steel butt hinges of size 100mm, 2 Nos 150mm long stainless steel tower bolt and 01 No 250mm long sliding bolt of all as per direction of Engineer-In-Charge.Make 'Rajshree or equvelent "

Description all as per item no 113 above but wire mesh door shutter all as per specification.

S&F for factory made solid PVC moulded door shutter with wood free, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

Description all as per item no 38 above but one coat over old treated walls.

M & L for preparing newly plastered surfaces of wall incl preparation of surfaces and applying two coats of oil bound distemper over a coat of interior primer and 2-3mm wall care putty (JK or Birla) on wall surfaces complete as specified and directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflorocent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of Oil bound distemper complete all as specified and directed.

S&F white colour Rotational moulded polyethylene water storage tank 1000 litres capacity, white triple layer construction (cylindrical vertical closed top),including 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball hoisted & fixed in position including all fittings complete all as specified and as directed.

Description all as per item No 120 above but 500Ltr capacity.

S&F in repair 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall / view cutter etc, fixed with self tapping screws with bent to a curve (of any radius as per required) including dismantling asbestos cement sheet in roof coverings ( corrugated , semicorrugated etc) any gauge, thickness, including, Nainital or similar pattern roof coverings sheet in any pattern & position of roof coverings.complete all as specified and directed

Description all as per item No 124 above but plain sheet.

S & F designer board false ceiling of size 600x600x4mm thick E-Board white prelaminated sett embosed reinforced tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction including taking down the existing false ceiling of any type with frame work complete all as specified and directed.

M&L for rubber moulded glossy finished Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with gray cement and pigment as in floors over and incl 15mm thick screed bedding layer in CM 1:6, complete all as specified and as directed.

M & L for 8mm thick (toughened glass) of approved quality fixed in any position (fixed glazed window, partition, bathroom enclosure and the like) including necessary all stainless steel hardware fittings (As like frame, brackets, clips, jammers, stoppers. etc.) complete drilled for fixing with all fitting and fixture including hacking out old glass, complete all as specified and as directed.

M&L for Mild steel hand rails, half round or other steel section or core for wooden hand-rail straight portion, for framed work as in doors truss purlin and rafter, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 , including of dimantling of old steel members complete all as specified and as directed.

M&L for prepration of old treated steel surface and applying one coats of synthetic enamal paint complete all as specified and directed.

Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches,Sockets, holders, ceiling roses, light fitting regulators etc (to be measured separately) and making good the disturbed surface all as directed.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked drawing in PVC concealed conduit and PVC conduit fitting including drawing FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size with modular sheet for fixing modular switches/sockets/fan regulator etc complete all as directed

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

Description all as per Srl Item No 132 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for independent point.

S&F Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed.

S&F Modular switch 6 & 16 Amp, 1 way, 2 module size complete all as directed.

S&F Modular socket 6 & 16 Amp multipurpose shuttered type, 2 module size with indicator lamp complete all as directed.

S&F Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

M&L Sub main wiring with 2 run of 4.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 4.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed. Note : Out of Qty 90 RM, 30 RM shall be provided as in replacement.

M&L Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in to separate PVC concealed conduit 25 mm dia with and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

S & F of MCB DB conforming to IP 43 - IK 09 with double door , SPN 8 way complete with din rail Neutral and earthing bar after taking out the oldunserviceable DBs connection and making good the disturbed surfaces, complete all as specified and as directed.

S&F of MCB SP, B Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F of MCB SPN B Curve type, 10 KA, 63 Amp, with over load and short circuit protection complete all as directed.

Supply and fix in replacement of Modular AC 25 Amp SP mini MCB, 230 Volts, 50 Hz suitable for 4 module incl sheet complete all as specified and as directed.

S & F in replacement of Energy efficicent LED fittings 45W LED 6K suitable for building security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

Supply and fixing street light fitting bracket, 1.0 mtr long bent to shape made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Material and labour for earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtr deep below normal ground level connected to galvinised earth wire 4 mm by means of nuts, bolts and check nut to earth plate and to main board or DB including necessary PCC 1:2:4 type B-1 pit, cover frame , GI pipe 15 mm dia light grade for protection and GI pipe 20 mm dia medium grade for watering with funnel, wire mesh, salt and charcoal dust all over the plate all as specified and as directed.

S & F surface / wall mounted LED tube light fitting with Aluminium housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed.

S & F LED energy efficient integrated battens fittings, Aluminium extruded heat sink with shatter proof opal shell of Aluminium housing, 10 Watts, cool/warm white as per site requirement, complete all as specified and as directed. Note : Out of Qty 10 Each, 8 Each shall be provided as in replacement.

Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing round shape 15/12 watt 220 volts AC surface/ recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F in Replacement of MCB DB conforming to IP 43 - IK 09 with double door, SPN 04 way, double door complete with din rail, Neutral and Earthing bar after taking out the old unserviceable DBs, connection complete and making good the disturbed surfaces.

M & L in replacement of Isolator SPN 40 Amps, 240 volts complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S&F of wall mounted fan 400mm sweep, Copper winding, 240 Volts. 50 Hz and depositing the old u/s to mes store yard, complete all as specified and as directed. Note : Out of Qty 06 Nos, 04 Nos shall be provided as in replacement.

S & F LED garden light Fittings with B22 LED lamp ,height of light 900 mm suitable for pathway lights including making base of PCC 1:2:4 (45x45 cm) with fixing fastner,Nut,Bolts in PCC from ground level and making good electric connections, complete all as specified and as directed. Make :- Cat part No - Li-8113 Lustre Illuminations. Note : Out of Qty 52 Each, 22 Each shall be provided as in replacement.

S&F high pressure booster pump with 8 ltr capacity pressure tank, coupled with electric motor of capacity 0.50 HP, 230 volts, single phase, 50 Hz incl Pressure Guage, Pressure switch & connecting accessories of GI i.e bend, nipple, socket, tee of requisite size etc incl cutting of existing pipe, complete all as specified and as directed. Note : Out of Qty 04 Nos, 02 Nos shall be provided as in replacement. Make: Usha/CG/V Gard/Khaitan/CR/Leader.

S & F in replacement of LED post top lantern fitting powder coated aluminium die cast and spun aluminium with clear/opal diffuser 36 Watt including LED driver with gallary suitable for mounting on 32/40 mm GI pipe including necessary electric connections complete all as specified and as directed.

S&F in replacement of picture light of 12 Watts, 450/600 mm length metal body suitable for focus on Name plates/paintings, complete all as specifed and as directed.

Taking down water heater (Geyser) 25 ltre capacity, and depositing to MES store yard.complete all as specified and as directed.

S&F electric water heater of capacity 25 litre, vertical storage type, steel inner tank with glass linen 5 star rating, withstand 8 bar pressure complete with all accessories such as heating element, pressure relief check safety valve, thermostat, connection piece, 3 core wire with plug etc all as specified and as directed. Note : Out of Qty 03 Nos, 02 Nos shall be provided as in replacement.

S&F of rigid non metallic PVC conduit 25 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc complete surface mounted / concealed and making good the surface all as specified and and as directed.

S&F cable pvc insulated copper conductor two core pvc sheathed circular 6 sqmm for electrification in Garden lights, gate light etc. complete all as specified and as directed. Note : Out of Qty 260 RM, 120 RM shall be provided as in replacement.

S&F modular Step Fan regulator, 120 watts single / double module all as directed. Make-Indoasian shynora/ Anchor Roma/ Legrand Arteor or equivalent.

S&F of LED Bed Side Flexible Arm lamp 5/6 W complete all as specified and directed.

S&F BLDC (Brushless Direct Current) Ceiling Fan ( energy efficient),1400 mm (as directed by Engineer-in-charge) BLDC Remote controlled suitable for regulator, voltage 220V,having full copper motor winding & ribbed 3 Nos A/M blades. The fan shall have BEE 5 star rating and making necessary electric connection of suitable PVC copper wire from ceiling rose to ceiling fan and service value more than 7.1 minimum air delivery 255 cmm, complete all as specified and directed.Make-Havells/ Atomberg/ Crompton/ Goldmedal.

S&F of Ventilating fan 200 mm sweep, plastic body type including self closing louver and making all electric connections, complete all as specified and as directed.

S & F MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connection complete all as specified and as directed.

S&F MCCB 3 pole of capacity 125A, 10KA (ics 100%) with thermal magnetic release including spreader/thimble of suitable size and making connection complete all as specified and as directed.

S & F Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed.

S & F of MCB C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, of capacity 6 to 16amps, complete all as specified and directed.

S & F Isolator suitable for 240 volts AC supply, SPN of capacity 63 Amps, complete all as specified and directed.

S&F Modular TV socket), 01 Module size, socket as per site requirement complete all as directed by the Engr-In-Charge.

S&F Modular Telephone socket, Jack 01 Module size (RJ 11 Socket Jack) complete with modular sheet as per site requirement complete all as directed by the Engr-In-Charge.

M&L for TV Wiring with Co axial RG-6 heavy duty PVC insulated, PVC sheathed cable having single strand of 0.7 mm dia taped suitable for telephone wiring and making all necessary connections from terminal box to TV socket, drawn in and including separate concealed PVC conduit complete all as directed.

M&L of telephone Wiring with twin core PVC insulated, PVC sheathed cable suitable for telephone wiring and making all necessary connections from terminal box to telephone socket, drawn in and including separate concealed PVC conduit complete all as specified and directed.

S&F ABS Plastic Automatic Hand Dryer (white standarad ) Power-1200W, Speed-1200 R/M ,Voltage-220V ,IPX1,complete all as specified and directed. Make : Philips/ Bajaj/ Havells.

S&F metalic box for single phase prepaid meter with door glass incl.all type of fixing accessories etc complete all as specified & as directed.

S&F Static Energy Meter three phase electronic type with LCD display of capacity 10-60Amp including connection with seal and sealing wire including taking out the old u/s and depositing to MES store yard, complete all as specified and as directed. Make: L&T/ ABB/ Secure/ Benlo)

Supply and fixing Flexible LED strip light tubular type, cool/warm white , (20W per metre) incl LED AC to DC adopter and making all electric connections complete all as directed.

Supply and fixing AC to DC adaptor for LED strip light tubular type complete all as specfied and as directed

Supply and fixing of wall light fitting with and incl 9 watt LED lamp complete all as directed. Make :- Cat part No - Li-3614/1W Lustre Illuminations or equavent approved.

Supply, laying and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 3.5 core.

M&L for sand cushioning to under ground cable provided with layers of snad(8 cms deep before laying the cable and 15 cms deep after laying) complete allas specified and directed at site by Engineer-in-Charge.

Supply and laying burnt bricks sub class - B, for protection of cable, complete all asspecified and directed at site.

S&F Galvanised steel tubing light grade of size 40mm bore for road crossing passing cable, complete all as specified and directed.

Rough excavation in trenches in hard rock/ road not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for shafts, wells, cesspits, manholes, pier holes and getting out including forming bottom surface for laying LT cable as specified and directed at site by Engr-in-Charge.

Cutting of GI Pipe Line25 mm dia medium grade for intersection of tee complete all as sepecified and as directed.

M&L for Tubes, 'medium grade bore (25mm)' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for Gun-metal, globe or gate valves bore dia of (20mm), with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M/s Shubh Enterprises (BID ID -3479788)

aggarwal engineers contractors (BID ID -3483464)