Repair of leakage of damages walls, room attached with existing building and miscellaneous work etc. at Veterinary Dispensary at Jawal Distt. Una (HP).

Excavation in earth work in all heights and depth in all kinds of soils, including saturated soil comprising of pick work, jumper work, and blasting work both in soft and hard rock with chiselling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer -in-Charge at site. according to the HP.PWD. specification

Providing and laying cement concrete 1:4:8 (1 cement:4 sand:8 graded stone aggregate 40mm nominal size) and curing complete including cost of form work in:Foundation and plinth and wall including carriage of materials upto all leads and lifts.

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts. Foundations, footings & bases of columns etc., Pedestal of columns and mass concrete.

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts columns, pillars, posts and struts square rectangular or polygonal in plan in any height as per the direction by the Engineer-in-charge .

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts Lintels, beams, plinth beams, girders, bressumers and cantilevers as per the direction by the Engineer-in-charge .

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts Suspended floors, roofs, landings, balconies, fecia , moulding and access platform as per the direction by the Engineer-in-charge .

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts Edges of slab, chajjas etc.

Providing form work with steel plates 3.15 mm( three decimal fifteen millimeter ) thick welded with angle iron in frame of 30x30x5mm(thirty into thirty into five millimeter) so as to give a fair finish including centering shuttering strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including carriage of materials upto all leads and lifts Vertical surfaces such as walls (any thickness) partitions and like i/c attached buttresses, pillasters, plith and string courses and the liike

Providing and laying cement concrete 1:1.5:3 (One cement : one point five sand :Three graded crushed stone aggregate 20mm nominal size)( Twenty milimetre) and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete workFoundations, footings, bases of columns and the like and mass concrete. including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Providing and layingReinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. including carriage of materials upto all leads and lifts.

Providing and laying Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, fecia ,mouldings, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size).and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. including carriage of materials upto all leads and lifts.

Providing and laying tor steel reinforcement for reinforced cement concrete work including ,bending binding,straightening and placing in position complete in all floor level/ heights including cost of binding wire complete including entire carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

Providing Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (1 Cement : 6 Sand) upto all height 1st Class Bricks including carriage of material within all leads and lifts and as per the direction by the Engineer-in-charge ..

Providing Brick work using common burnt clay building bricks in superstructure 1:6 (1cement:6sand) up to all height including carriage of material within all leads, lifts and heights. 1st class bricks as per the direction by the Engineer-in-charge .

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Providing and fixing toughned glass glazing in aluminium door, window, ventilator shutters and partition etc with PVC/neoprens gasket and including aluminium beading complete as per the architectural drawings and the directions of Engineer-In_charge including cost of aluminium snap beading . glazing with glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm. including carriage of materials upto all leads and lifts.

Providing and fixing 12mm thick prelaminated Particle board board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. Pre-laminated particle board with decorative lamination on both sides including carriage of materials upto all leads and lifts.

Providing and fixing stainless steel wire gauge of IS gauge designation 140 g with wire of dia 0.71 mm to windows and clerestory windows including beading of aluminium including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Providing and fixing Stainless steel sliding door bolt with bolts and nuts screws etc., complete: including carriage of materials upto all leads and lifts. 250X16 mm as per the direction by the Engineer-in-charge .

Providing and fixing Stainless steel hooks and eyes with screws etc., complete including carriage of materials upto all leads and lifts 125mm as per the direction by the Engineer-in-charge .

Providing and fixing Stainless steel tower bolt with screws etc., complete including carriage of materials upto all leads and lifts 150x10mm as per the direction by the Engineer-in-charge .

Providing and fixing Stainless steel handles with necessary screws etc., complete: including carriage of materials upto all leads and lifts 150x10mm as per the direction by the Engineer-in-charge .

6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to three Sand) in all floor level. The rate isincluding carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

15mm (fifteen milimetres) thick cement plasters in single coat on rough/fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty two coats over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials upto all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth and cement primer complete. including carriage of materials upto all leads and lifts.

Providing and fixing double charge 10mm thick anti skid water proof stain and impect resistent heavy duty and Mat Finish vetrified tiles Nitco or equivalant 800mmx800mmx10mm manufactured of required shade and colour in flooring, treads of steps and landings laid with spacers laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with grouting of Epoxy material mixed with pigment to match the shade of tiles in all storeys, height, levels and location as required complete.including carriage of materials upto all leads and lifts.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. including carriage of materials upto all leads and lifts.

Providing and laying chequered tile 22mm thick laid on 20mm thick cement mortar 1:4(1 Cement : 3 Sand) including preparation of ground including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paintIn gratings framed guard bars,ladders,railling,brackets and similar works.including carriage of materials upto all leads and lifts as per the direction by the Engineer-in-charge .

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of materials upto all leads and lifts

Providing and fixing ridges or hips 60 cm overall with 0.47 mm Thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of materials upto all leads and lifts. Tata Shakti make.including carriage of materials upto all leads and lifts.

Providing and fixing of M.S. BP sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of the Engineer-in-charge. (weight of sheet not less than 15kg/sqm).including carriage of materials upto all leads and lifts.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge.60 mm thick C.C. paver block of M-30 grade with approved color design and pattern.by using 50% colour Grey and 50% Colour Red. as per the direction by the Engineer-in-charge .

Please Enable Macros to View BoQ information