SPECIAL REPAIRS TO BUILDING No. ET-226 AND ET-523 AT HATTIGOR MILITARY STATION UNDER GE RANGIA

Amount

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Dismantling unframed timber scantlings 40 sq. cm and over in section, in any position and all as specified and directed.

Dismantling framed timber scantlings in rails, posts, rafters, purlins, etc. under 40 sq. cm in section and over in section, in any position and all as specified and directed.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position and all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and all as specified.

S&F of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 450 mm centre to centre and suspended from GI wire of 3mm dia and all as specified and directed

S&F 4mm thick Non asbestos fibre cement building board / E-board fixed to GI frame (snapgrid) of standard section as per manufacturers instructions fixed in ceiling flat or sloped complete all as specified.

M&L for Second class hard-wood in scantlings, wrought timber framed and fixed, complete all as specified and as directed by Engineer-in-charge.

S&F MS steel work in tubular trusses including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240, complete all as per specified and as directed by Engineer-in-charge.

S & F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (GdeE- 250) quality B, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

M&L for providing two coats of synthetic enamel paint over a coat of red oxide primer on steel Surfaces of any description, over 10cm in width or girth, not otherwise described, complete all as specified and as directed by Engineer-in-charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft soil, complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B1 (1:2:4) 20mm graded aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B1 (1:2:4) 20mm graded aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed by Engineer-in-charge.

M&L for RCC (nominal mix) type B1 (1:2:4) 20mm graded aggregate as in columns, pillars, piers, posts and struts, complete all as specified and as directed by Engineer-in-charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; finished in rough surfaces vertical or to batter, complete all as specified and as directed by Engineer-in-charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, complete all as specified and as directed by Engineer-in-charge.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality confirming to Fe-410-S 0r Fe-410-O, complete all as per specified and as directed by Engineer-in-charge.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and dia of bolt 16 to 20mm, complete all as per specified and as directed by Engineer-in-charge.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as per specified and as directed by Engineer-in-charge.

S&F of GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, complete all as per specified and as directed by Engineer-in-charge.

Demolition of brickwork / block masonry built in cement mortar including all quoins, arches, pillars etc., complete all as per specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built and set in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in one brick thick walls built and set in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

Taking down cement plaster of any description incl raking out joints, haking for key scrubbing down with water etc, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick on brick or concrete surface in CM 1:6 and surface finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick on brick or concrete surface in CM 1:4 and surface finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new surfaces of wall including scrapping down, etc and applying two coats of oil bound distemper over a coat alkali resistant primer over 1mm thick wall care putty (white or tinted), complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new surfaces of wall including scrapping down, etc and applying two coats of cement based paint over a coat of primer, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of old surfaces of wall including scrapping down, smoke soot, efflorescence salts, treading oil, greasy spots etc and applying 1mm thick wall putty and applying two coats of Oil Bound Distemper over a coat of primer, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of old surfaces of wall including scrapping down, smoke soot, efflorescence salts, treading oil, greasy spots etc and applying one coat of Oil Bound Distemper, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of old surfaces of wall including scrapping down, smoke soot, efflorescence salts, treading oil, greasy spots etc and applying one coat of cement based paint, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing one coat of synthetic enamel paint on old steel Surfaces of any description, over 10cm in width or girth, not otherwise described, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing one coat of synthetic enamel paint on old wooden surfaces of any description, over 10cm in width or girth, not otherwise described, complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description not exc. 1 sqm each, complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description exc. 1 sqm not exc. 2 sqm each, complete all as per specified and as directed by Engineer-in-charge.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge.

M&L for 35 mm thick second class hardwood glazed and skeleton shutter for doors open rebated and prepared to receive glass, gauge etc. (without sash bar) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. sizes of member as specified in SSR part I section & clause 8.24 (a), complete all as per specified and as directed by Engineer-in-charge.

S&F 35mm thick, 2nd class hard wood of Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, for windows and ventilators etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats, complete all as per specified and as directed by Engineer-in-charge.

Taking down Chowkhat or frames exceeding 1.5Sqm but not exceeding 4.0 Sqm each with shutters (Without taking off shutters from the frames), complete all as per specified and as directed by Engineer-in-charge.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as per specified and as directed by Engineer-in-charge.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with wood free EPS with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site, complete all as per specified and as directed by Engineer-in-charge.

S&F stain less Butt hinges, 100mm medium weight, cold rolled mild steel, complete all as per specified and as directed by Engineer-in-charge.

S&F Extruded aluminium alloy handles 150mm fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F Extruded aluminium alloy handles 100mm fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F Aluminium anodised, barrel tower bolts 150mm of extruded section and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F Aluminium anodised, barrel tower bolts 100mm of extruded section and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F Aluminium alloy, anodised, 300mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F 300 mm long Helical door Spring of approved quality, complete all as per specified and as directed by Engineer-in-charge.

Supply and fix in repair aluminium anodised door shutter sliding/ side hung type and provided with 5.5 mm thick tinted glass on top and bottom panel fixed with taper clip and locking arrangements with necessary fittings including frame The section for shutter shall be taken as under :- (a) Top rail 44.50 x 47.62 x 1.42 mm thick (b) Door vertical 44.45 x 47.62 x 1.52 mm thick (c) Bottom rail 44.45 x 95.25 x 1.70 mm thick (d) Door middle 44.45 x 49.91 x 1.60 mm thick

M&L for preparing of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer of any description, over 10cm in width or girth, not otherwise described, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as per specified and as directed by Engineer-in-charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as per specified and as directed by Engineer-in-charge.

S&F Sheet glass, 3mm thick ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair sheet glass, 3mm thick ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane including taking down of old glass panes, complete all as per specified and as directed by Engineer-in-charge.

Excavation in post holes (or similar holes) each n.exc 0.5cum in soft/loose soil and getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing of surplus soil to a distance n.exc 50 meters and making good surface, complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC (1:4:8) type D2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as per specified and as directed by Engineer-in-charge.

M&L PCC (1:2:4) type B0 using 12.5mm graded aggregate 25mm thick as in sub base of floor finished even and rough to receive top layer, complete all as per specified and as directed by Engineer-in-charge.

M&L for 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor, complete all as per specified and as directed by Engineer-in-charge.

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as per specified and as directed by Engineer-in-charge.

All as per serial item no. 65 above but on skirting.

M&L for rendering 10mm thick in CM (1:4) finish the surface even and rough to receive the wall tiles, complete all as per specified and as directed by Engineer-in-charge.

M&L for Glazed coloured ceramic tiles in vertical surfaces 300 x 450 x 7-8mm thick set and jointed in neat cement slurry and pointed in white or coloured cement ot match the tiles, complete all as per specified and as directed by Engineer-in-charge.

M&L for granite 20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as per specified and as directed by Engineer-in-charge.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles, complete all as per specified and as directed by Engineer-in-charge.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles, complete all as per specified and as directed by Engineer-in-charge.

Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

M&L PCC (1:3:6) type C2 using 20mm graded aggregate 75mm thick as in plinth protection finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for chequered cement concrete PU finish tiles 300mm x 300mm x 25 mm thick in floor etc, set, jointed and pointed in neat cement slurry and pointed (grey cement & pigment) over 20mm thick screed bed or bedding layer of cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

Dismantling of PVC drain pipes jointed in cement mortar and taking out from trenches or walls of any bore including fittings, complete all as per specified and as directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as per specified and as directed by Engineer-in-charge.

S&F PVC (SWR) floor trap 75mm outlet dia setting and jointing with solvent cement, complete all as per specified and as directed by Engineer-in-charge.

Taking out steel water tubing and connections including cleaning for refixing 20 mm dia., complete all as per specified and as directed by Engineer-in-charge.

Taking out steel water tubing and connections including cleaning for refixing 15 mm dia., complete all as per specified and as directed by Engineer-in-charge.

S&F 15 mm bore Galvanized Steel tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as per specified and as directed by Engineer-in-charge.

S&F 20 mm bore Galvanized Steel tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as per specified and as directed by Engineer-in-charge.

S&F 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed, complete all as per specified and as directed by Engineer-in-charge.

S&F 15 mm bore Stop valves, cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as per specified and as directed by Engineer-in-charge.

S & F in repairs viterous china oval shape above counter sunk wash hand basin white flat back including waste coupling, CP conector and Basin mixer etc including granite slab and all connected items, complete all as per specified and as directed by Engineer-in-charge.

S&F in repairs viterous china wash down water closet floor mounted (Pedestral pattern) EWC including combined viterous china flushing cistern of 10 ltr Capacity white incl plastic water closet seat cover and mild steels chromium plated on aluminium hinging device and connecting to outlet pipe with flushing rim, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair tubular towel rail brass chromium plated 20 mm dia 'D' type 60 cm long between flanges, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair angular stop valve 15 mm chromium plated concealed, fancy type screwed down high pressure screwed both ends for iron pipe for 15 mm bore, complete all as per specified and as directed by Engineer-in-charge.

S&F in repair CP health faucet shower with CP flexible pipe 15mm bore (ABS Body) with 1 mtr long easy flex tube in chrome finish, complete all as per specified and as directed by Engineer-in-charge.

S&F in repairs PVC (SWR) floor / gully trap 125/110 mm, setting and jointing with solvent cement inclding necessary gratings, complete all as per specified and as directed by Engineer-in-charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specificied provided for, complete all as per specified and as directed by Engineer-in-charge.

M&L second class hard wood plain fillets square, rectangular or triangular in section ,clean sawn , secured with nails or brads face sectional area exc. 6 and not exceeding 13 sqcm, complete all as per specified and as directed by Engineer-in-charge.

M&L second class hard wood plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads face sectional area exc 13 and not exceeding 25 Sqcm, complete all as per specified and as directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/loose soil, complete all as per specified and as directed by Engineer-in-charge.

Removing Excavated soils n exc 50 M m and depositing where directed at a level not exc1.5 M above the starting point, complete all as per specified and as directed by Engineer-in-charge.

Taking down carefully aluminum/copper point wiring (light fan, socket or power) complete incl fittings and fixtures such as switches, sockets, light fittings, ceiling rose, pendants, lamp holders, shade conical, regulators etc and separating serviceable fittings for reuse in the same work and removing unserviceable fittings and fixtures with wiring cable, battens, wooden boards etc from site and making good disturbed surfaces of walls, floors, ceiling etc all complete all as specified and directed complete all as per specified and as directed by Engineer-in-charge.

Taking down carefully unserviceable main switches and DB’s including wooden boards and removing from site including making good disturbed surfaces of walls complete all as per specified and as directed by Engineer-in-charge.

Dismantling of house service brackets of any size and type and making good the distrubed wall surfaces complete all as per specified and as directed by Engineer-in-charge.

M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated unsheathed single core multi stranded FRLSH copper conductor cable drawn into and incl PVC casing capping sleeves and caps of adequate width and length with all accessories and fittings like bends . elbow crosses etc with PVC round block and PVC terminal boxes with 3.00mm thick laminated sheet cover for mounting fittings etc like switches sockets and fan regulator incl 1.5 sqmm size PVC insulated multistranded FRLSH copper conductor cable as earth continuity conductor and connected to earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed by Engineer-in-Charge.

All as per Serial item No. 101 above but for one fan point controlled by one way switch.

All as per Serial item No. 101 above but for one 3 pin socket outlet 5 AMPs on same board.

All as per Serial item No. 101 above but for one 3 pin socket outlet 5 AMPs on independent board.

All as per Serial item No. 101 above but for one bell push point controlled by one 5 amps bell push.

All as per serial item no. 101 above but with 4 sqmm (nominal area) cable with 4.00 sq mm size copper earth continuity conductor of green colour for 15 A socket on independent boards.

Supply and fix switch socket combination 05/16 Amp 6 pin flush type, complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch piano flush type, 6 Amps 240 volts single pole one way, complete all as specified and as directed by Engineer-in-charge.

Supply and fix socket outlet, 3 pin 5/6 Amps, flush type, complete all as specified and as directed by Engineer-in-charge.

Supply and fix switch socket combination 05/06 Amp 3 pin flush type, complete all as specified and as directed by Engineer-in-charge.

Supply and fix ceiling rose surface backelite three terminals, PVC/polycarbonate, insulated body, complete all as specified and as directed by Engineer-in-charge.

Supply and fix bell push 5 Amp flush type single pole 230 volts one way complete all as specified and as directed by Engineer-in-charge.

Supply and fix fan regulator electronic type, flush type 240 Volt, complete all as specified and as directed by Engineer-in-charge.

Supply and fix LED tube light fittings1 x 20 Watt, 220 V, AC decorative box type with driver holder including LED tube rodconnecting up with three core flexible copper conductor cable from ceiling rose to tube light fitting complete all as specified and as directed by Engineer-in-charge.

Supply and fix lamp holder, PVC/Polycarbonate type complete all as specified and as directed by Engineer-in-charge.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and as directed by Engineer-in-charge.

S&F Security light fittings 18 Watt LED New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP openning seperate driver compartment with IP65 protection and impact resistance of IK07 and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size, complete all as specified and as directed by Engineer-in-charge.

Taking down old ceiling fan/exhaust fan and to be kept safely in store and refixing the same fans after proper cleaning and testing to its original position, complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SPN 240 Volts 6-32 Amp breaking capacity 10 KA rating, complete all as specified and as directed by Engineer-in-charge.

Supply and fix MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating complete all as specified and as directed by Engineer-in-charge.

Supply and fix sheet metal enclosure powder painted for MCB SPN 12 way double door DB with din rail and suitable bus bar complete all as specified and as directed by Engineer-in-charge.

Supply, fixing & testing of 10 Sqmm 2 core XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminum conductor, 1100Volt grade including taking down old unserviceable cable complete all as specified and as directed by Engineer-in-charge.

S&F in repair building security light bracket made out of GI tubing 25 mm bore medium grade 1.20 Mtr long bend to required shape as in bracket for street light fittings fixed with two pair or MS flat iron 40mm x 5mm size and of required lenth and shape with bolts nuts and washers suitable for steel tubular pole including painting of mild steel flat iron surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-charge.

S&F PVC rectangular block for mounting, DBs, etc. with 3mm thick plastic laminated sheet cover of size 300 x 250 x 50 mm deep complete all as specified and as directed by Engineer-in-charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified and as directed by Engineer-in-charge.

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade) and chamber and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 3 of SSR PT 1, 1991 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switches, DBs) including taking down old unserviceable one, complete all as specified & testing on completion. NOTE:- (I) item includes the cost of 7.5 mtr length GI pipe for protection for GI earth wire. (ii) item rates includes the cost of 7.5 mtr earth lead GI earth wire. (iii) PCC pit shall be provided at least 500mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe,bends,elbow etc shall be deemed included in the unit rate.

Supply & laying 32 mm dia High density polyethylene pipes (HDPE) for Cable protection of pressure rating 6 kgf/cm2 laid in trenches complete all as specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/S Rajkamal Enterprise

M/S SITAL BUILDERS