GE/863/EWS-T-49 OF 2024-25 SPL REPAIR CERTAIN MISC WORKS AT POOH

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness including cover fillets/ frame complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Naintal or similar pattern roof coverings, complete all as specified and directed.

Taking down Chowkats or frames not exceeding 1.5 Sqm each but with shutter (Without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but not exceeding 4 sqm each but with shutter (without taking off shutter from the frame) complete all as specified and directed by Engr-in-charge.

Dismantling timber scantlings 40 sq.cm and over in section, in any positions as in framed work, complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm in thickness (Below or above ground level), complete all as specified and directed by Engr-in-charge.

Excavating in trenches, not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm area on plan and not exceeding 1.5 meter in depth and getting out in soft/disintegrated soil, complete all as specified and directed by Engr-in-charge.

M & L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation/filling and mass concrete, complete all as specified and directed by Engr-in-charge.

Demolition of brick work or stone/ boulder/ block masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engr-in-charge.

M&L for Precast cement concrete 1:3:6 type C1 (Using 20 mm graded crushed stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) , complete all as specified and directed by Engr-in-charge.

M & L for Reinforced Cement Concrete M-25 (using 20 mm graded crushed stone aggregate) design mix as in foundations including Plinth beam, base for column, rafts, footings and mass concrete, complete all as specified and directed by Engr-in-charge.

M&L for RCC design mix M-25 grade, using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts & similar RCC works complete all as specified and directed by Engr-in-charge.

M & L for Reinforced Cement Concrete design mix M-25 (using 20 mm graded crushed stone aggregate) as in Beams, cantilevers, lintels over 1.5 M span complete all as specifed and directed

M & L for Reinforced Cement Concrete design mix M-25 (using 20 mm graded crushed stone aggregate) as in Chajjas and the like, complete all as specified and directed by Engr-in-charge.

M & L for 10mm dia and over TMT bars cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel (annealed) wire not less than 0.90mm dia complete all as specified and directed by Engr-in-charge.

M & L for 5mm dia and over up to 10 mm dia TMT bars cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel (annealed) wire not less than 0.90mm dia, as in stirrups, spacers and binders complete all as specified and directed by Engr-in-charge.

Use & waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams and similar works for rough finished surface complete all as specified and directed by Engr-in-charge.

Use & waste form work to sides of pillars, posts and columns for rough finished surface of concrete complete all as specified and directed by Engr-in-charge.

Use & waste Form work to sides and soffits of floor or roof beams, lintiles cantilever etc for rough finished surface complete all as specified and directed by Engr-in-charge.

Use & waste Form work to edge of concrete , flats, treads, breaks in floors, window cills etc for rough finished surface exc 5 cm but n. exc 10 cm wide complete all as specified and directed by Engr-in-charge.

M&L for rendering 5 mm thick on concrete surfaces of wall / vertical surfaces in cement mortar 1:3, and finish the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-In-Charge.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finish the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-In-Charge.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-charge.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of flooring/ hard standing complete all as specified and directed by Engr-in-charge.

M&L for 100 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in sub base of flooring complete all as specified and directed by Engr-in-charge.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finished to receive floor tiles/granite complete all as specified and directed.

M&L for rendering of 10 mm thick cement mortar 1:4 as a backing coat rough finished to receive wall tiles/granite in dado/skirting complete all as specified and directed.

M & L for Vitrified Ceramic tiles Light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of the tiles, complete all as specified and directed.

M & L for Vitrified Ceramic tiles Light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, on walls in dado/skirtting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of the tiles complete all as specified and directed.

M & L for Chequred cement concrete tiles 20cm x 20cm x 25 mm thick with grey cement and pigment set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of the tiles complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection, laid to a slope of 1 in 12 in a manner that top face shall conform to the finished level of PCC adjacent to the edging. PCC shall be laid in alternate bays (not exc. 2.5 meters length) and finished even and smooth without using extra cement. 6 mm wide joints shall be provided throughout the thickness of plinth protection in concrete bays at corners and turning points and also in between walling and plinth protection. All joints in bays, as well as between walling and the concrete in plinth protection shall be filled in with mastic filling comprising 1 part of heated bitumen 85/25 grade and 3 parts of sand (all by weight) complete all as specified and directed.

S&F pressed steel frames 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

M&L for Plain Cement Concrete 1:3:6 type C1 (using 20mm crushed stone aggregates for filling of pressed steel frame and hold fast block etc., complete all as specified and directed.

S & F of 35 mm thick factory made second class hard wood, kiln seasoned and chemically pressure treated plain framed, panelled shutter (Two panel) with lock rail and panel of 9 mm BWP Commercial ply or 12 mm veneered particle board with commercial face veneers on both faces or 10 mm bison panel, complete all as specified and directed.

Supply and fixing (factory Made) 2nd class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive gauge (Without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

Supply & fixing steel windows/ventilator with side hung shutters including projection type hinges with steel handle, tower bolt and steel peg stay, complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F of Prepainted galvalume aluminum zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength of 550Mpa as in roof coverings fixed with self tapping screws, complete all as specified and directed.

S&F of Prepainted galvalume aluminum zinc coating GI based plain steel sheeting 0.50 mm thick any colour having tensile strength of 550Mpa as in roof coverings fixed with self tapping screws, complete all as specified and directed.

S & F Rolled Mild Steel sections confirming to Fe 410-W (Gde-E-250) quality A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connecting plates, complete all as specified and directed.

S&F of plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment including welding etc., confirming to Fe-410-W(gde-E-250) quality B, complete all as specified and directed.

S&F mild steel works F.I. (40x6) wind ties for roof incl securing bolts, necessary drilling, bolting or riveting, etc. and similar work, confirming to Fe-290 (gde-E-165) complete all as specified and directed.

S&F Anodised aluminum snap grid framed work for false ceiling and incl hangers 6mm dia G.I (upto 1200mm long) adjusting level fixed to roof slabs/purlin/rafter with the help of cleats made out of G.I flat 40x3mm size 60mm long and expansion holdfastener 12.5mm dia 40mm long complete all as specified and directed.

M&L for false ceiling with gypsum board, perforated type, ,factory made matt finish surface/pre painted surface, 600 x 600 mm in size and 12 to 15 mm thick on exisiting aluminum snap grid 605 X 605 mm as in ceiling, complete all as specified and directed.

S&F in repair 19 mm dia curtain rods fancy type, mild steel chromium plated with fixing brackets, stops, rollers all as specified and as directed by Engr-in-charge.

S&F of floor door stopper 140 mm of aluminum alloy body and tongue anodised with hard drawn steel spring complete all as directed by Engineer-in-charge.

Supply & fixing of MS barrel tower bolt of 100mm long stove enamelled black with bright bolt complete all as specified and directed by Engr-in-charge.

Supply & fixing 300 mm long mild steel sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolts plate and two on couple plate and fixed complete all as specified and directed by Engr-in-charge.

Supply & fixing MS pressed handle oval type stove enamelled black of 125mm long fixed with screw to shutter complete all as specified and directed by Engr-in-charge.

Supply & fixing of 300 mm mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply & fixing of galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm & fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed.

S&F plain sheet glass of 3 mm thick in Squares not exceeding 0.50 Sqm in each pane with oil putty and clips complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new plastered surfaces and applying two coats of distemper oil emulsion on surfaces of walls, complete all as specified and directed.

M&L for preparing old plastered surfaces and applying two coats of distemper oil emulsion on surfaces of walls, complete all as specified and directed.

M&L for preparing new plastered surfaces and applying Two coats of cement base paint on surfaces of walls over and incl one coat of white wash, complete all as specified and directed.

M&L for preparing new plastered surfaces and applying Two coats of cement base paint on surfaces of walls over and incl one coat of white wash, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat synthetic enamel paint over and incl one coat of red oxide primer complete all as specified and directed by Engr-in-charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of black Japan paint over and incl one coat of red oxide primer (in embedded portion) complete all as specified and directed by Engr-in-charge.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying a coat synthetic enamel paint complete all as specified and directed by Engr-in-charge.

M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying a coat synthetic enamel paint (ordinary tint) complete all as specified and directed by Engr-in-charge.

M&L for joint free vitrified coloured tiles 8 to 10 mm thick grade BII matt superior finish first quality, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of the tiles complete all as specified and directed.

M&L joint free vitrified tiles coloured tiles 8 to 10 mm thick grade BII matt superior finish first quality area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in dado/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of the tiles complete all as specified and directed.

M&L joint free Non-Skid ceramic coloured tiles 7 to 8mm thick grade BII matt superior finish first quality area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the color of the tiles complete all as specified and directed.

S&F in repair Vitreous China, pedestal pattern white including trap set with concrete including Seat and cover,10ltrs low level fluslhing cistern with flush pipe complete all as specified and directed by Engr-in-charge.

M&L for Granite (of any type) 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

S & F in repair for Wash Hand basins, Vitreous China, white, flat back, size 550x440mm, including cutting for and pinning in ends of brackets or erecting stand, angle bracket (but exclusive of fixing of supply, waste pipe, taps) complete all as specified and directed.

S&F in repair bib taps 15mm dia fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed. complete all as specified and directed by Engr In Charge.

S&F in repair Angle/ stop valve of PTMT any colour pressure screwed for iron pipe and fixed (15mm minimum weight 90 Gms) for 15mm bore iron pipe, complete all as specified and directed.

Supply & fixing 15mm pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down , high pressure, with or without lettered 'Hot' or Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore of pipe complete all as specified and directed by Engr In Charge.

S&F for waste coupling of PTMT for 32 mm bore dia of discharge pipe (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) incl waste pipe of 32mm bore complete all as specified and directed.

S&F in repair of PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F in repair cast iron floor trap 75mm out let dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

M & L for Gully traps salt glazed stoneware (SGSW) square or round mouthed type 'P' of size 180x100mm for drain pipes complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints , laid in tenches or in floors, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints , laid in tenches or in floors, complete all as specified and directed.

S & F for 75 mm bore PVC (SWR) pipe, bends, any radius, complete all as specified and directed.

S & F for 110 mm bore PVC (SWR) pipe, bends, any radius, complete all as specified and directed.

S & F for 110 mm bore PVC (SWR) pipe, junction single 'T' equal or unequal, complete all as specified and directed.

S & F for PVC (SWR) 110 mm bore pipe, vent cowl, complete all as specified and directed.

S&F in repair soap dish vitreous china white, approximate size 160x160x90mm embedded in the wall, complete all as specified and directed.

S&F in repair towel rail 600mm having cat part No ACN-CHR-11115M of Jaguar/equivalent complete all as specified and as directed.

S&F in repair wall mixture 3 in 1 system having cat part No FLR-5281 (Floretine) of Jaguar/equivalent complete all as specified and directed.

S&F in repair overhead shower single flow, 100mm dia (ABS CP) with shower arm of length 100mm having cat part No OHS-CHR-1989 of Jaguar /equivalent connected with 15 mm bore of pipe complete all as specifed and directed.

Taking up or down 20mm bore steel water tubing & connections, complete all as specified and directed.

Taking up or down 25mm bore steel water tubing & connections, complete all as specified and directed.

S&F 3-layer PP-R (Polypropylene random copolymer) of outer dia 20 mm concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all specified and as directed.

S&F 3-layer PP-R (Polypropylene random copolymer) of outer dia 25 mm concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all specified and as directed.

M&L for 6mm thick ply wood, grade BWR, type BB fixed with screws to timber frame work in partitions/shutters, ceiling etc complete all as specified and directed.

M&L vennered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces, fixed with screws to timber frame work etc complete all as specified and directed.

M&L in repairs 18/19mm thick particle board, medium density, flat pressed single line layer type or three layer type with BWR type adhesive fixed with screws to timber frame including dismantling existing board complete all as specified and directed.

M&L for providing cement concrete cast in situ 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edge incl use of formwork, etc., complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed.

M & L for cement concrete Type C2 (1:3:6, 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed

S & F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F in repairs galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails including securingor tying at crossings with provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) alongwith compete fittings such as switches ,ceiling rose, pendent holder, sketch fitting & regulator etc. (Schedule of credit for each item to be given separately) including making good to the disturbed surfaces of wall, roof and floor etc. to match with the existing surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down unserviceable submain wiring and service cable alongwith batten /PVC conduits etc. and making good disturbed surfaces of walls/floors and match the existing surface complete all as specified and directed at site.

Taking down unserviceable main switches, DBs with MCB SP/Isolators by unscrewing form board complete all as specified and directed by Engineer-in-Charge

M&L for point wiring using approved colour coding as per IS with using approved colour coding as per IS 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continuous earthing in & incl PVC Casing and caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision PVC Box on top for fixing switches sockets etc. all as specified for one light point/ fan /Bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 101 here-in-before but controlled with one 3 pin socket outlet 5 Amp on same board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 101 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the independent board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 101 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with cable 2.5 sqmm including provision of 1.5 sqmm single core multistanded PVC insulated copper conductor as earth conducting conductor complete all as per specified and directed by Engineer-in-Charge.

S & F Modular switch 1 way 6 Amp, 1 module, multipurpose flush type, 230 V, ISI marked, complete all as specified and directed.

S & F Modular socket 6 Amp, 2&3 pin combined, 2 module, multipurpose flush type, ISI marked, complete all as specified and directed.

S & F Modular socket 6/ 16 Amp, 2&3 pin combined, 2 module, multipurpose flush type, ISI marked, complete all as specified and directed.

S & F Modular switch 1 way 16 Amp, 1 module, multipurpose flush type, ISI marked, complete all as specified and directed.

Supply and fix MODULAR WHITE COVER PLATE WITH FRAME White cover plate with frame, 3 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR WHITE COVER PLATE WITH FRAME White cover plate with frame, 4 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR WHITE COVER PLATE WITH FRAME White cover plate with frame, 6 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR WHITE COVER PLATE WITH FRAME White cover plate with frame, 8 module ISI marked complete all as specified and as directed.

Supply and fix MODULAR METAL FLUSH BOX 3 module, ISI marked, complete all as specified and as directed.

Supply and fix MODULAR METAL FLUSH BOX 4 module, ISI marked, complete all as specified and as directed.

Supply and fix MODULAR METAL FLUSH BOX 6 module, ISI marked, complete all as specified and as directed.

Supply and fix MODULAR METAL FLUSH BOX 8 module, ISI marked, complete all as specified and as directed.

Material and labour for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing recessed mounted/ceiling downlight 36W with pressure die-cast aluminium housing for effective thermal management, high transmission factor PMMA diffuser for better performance and suitable driver, complete all as specified and directed.

Supply and fixing surface & wall mounted LED 20W (Warm white) tube light fitting batten 4 feet, mirrorlite slim type with extruded aluminium housing alongwith 20W LED lamp PC body with all accessories complete all as specified and directed.

Supply and fixing surface & wall mounted LED 10W tube light fitting batten mirrorlite slim type with extruded aluminium housing alongwith 10W LED lamp PC body with all accessories complete all as specified and directed.

Supply and fixing Recessed mount LED 12 watts downlight with in built LED driver, injection moulded housing and made of high translucent frosted optically efficent for anti-glare and smooth light distribution, complete all as specified and directed.

M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed by Engr-In-Charge.

Supply & Fixing LED light fitting 1x9W / 10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F exhaust Fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V,50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as per specified and directed by Engineer-in-Charge.

Supplying, laying, jointing & testing in replacement of cable XLPE insulated as per IS 7098 (Part-I)-1988, marked, screened, PVC sheathed armoured electric power cable ( heavy duty) with aluminium conductor for working voltage upto and including 1100 Volts croos sectional area 16 Sqmm 4 core with aluminium stranded, complete all as specified and directed.

Supply and laying of well burnt class ‘B’ bricks as mechanical protection to under ground cables laying with length of the bricks perpendicular to the width of the trenche complete all as specified and directed.

Returning and filling in soil in two parts:- (i) Using riddled soil obtained from excavated soil up to depth of 30 cm (8cm below cable and remaining above cable for cushioning of cable, (ii) refilling the trench of remaining depth with normal excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified & directed by Engineer-in-charge. Note:- Excavated soil shall be riddled by using sieve to separate composite particles etc., as per IS 1255-1983 and refilling in trenches as in cable cushioning.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Supply, Fixing, and Testing Electric water heater 230 V, single phase, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as multifunctional safety valve, thermostat, NRV, automatic thermal cutout, fusible plug, anti-vacuum system, built-in pressure release valve, rust proof powder coated body, indicator lamps, connection piece etc including provision of grouting bolts in walls, stop cock, pvc connection etc. and all safety advices as per E-in-C's branch technical instructions and making good disturbed surfaces complete all as specified and directed by Engineer-in-charge.

Supply and fixing of sheet metal enclosure double door for DBs triple pole and neutral for 8 way 415 volt complete all as specified and directed by Engineer-in-Charge.

S&F with connection, testing and commissioning of MCB TPN 63 Amp, rating 415V, 10 KA, in the MCB DB complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 40 Amp,10 KA, 240 V complete all as specified and directed by Engineer-in-Charge.

S&F MCB SPN 16-25 Amp,10 KA, 240 V complete all as specified and directed by Engineer-in-Charge.

S&F MCB SP 6 Amp to 32 Amp, 10 KA complete all as specified and directed by Engineer-in-Charge.

M&L in replacement for Earthing complete with GI steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI earth wire of 4 mm dia protected by GI protection pipe light grade of 40mm bore dia from mechanical injury, 20 mm medium grade for watering with funnel, including test point up to 7.5 meter from earth pit, adequate quantity of common salt, charcoal dust, chemical and connected to test point by means of bolts and nuts washers made out of GI all as shown in Electrical plate No 3 of SSR part I including necessary earthwork and excavation in any type of soil, PCC 1:2:4 type B1 chamber with 40mm thick RCC 1:2:4 type mix cover slab with 6mm dia MS bars at 100mm dia both ways with MS hook 6mm dia MS bars etc. complete all as specified and directed by Engr-in-charge. Note: 1. Suitable quantity of charcoal, common salt, funnel, GI pipe required for watering, pit & CI pit cover etc is deemed to be included in quoted rate and lead wire used beyond 7.5m from pit cover will be measured separately. 2. On testing after completion if the desired resistance is not obtained the earthing shall be re-done at no extra cost.

S&F in replacement of Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground level complete all as per specified and directed.

S&F in replacement of Galvanised iron strip 32x6mm burried in ground inter connected to each earthing of Bldg complete all as specified and directed.

M & L for replacement of Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as per specified and directed. Note: It must be water proof metal box or PVC box with hinged door and locking arrangement.

M & L for replacement of Air termination, single pointed aluminium rod 12mm dia and 300mm long on the roof of GI sheet shelter inc GI pipe protection installed by means of coupling/ bracket, nut, bolt, washer, etc., complete with insulation block complete all as per specified and directed. Note:- 1. The conductors and termination point should not touch the bldg surface and quoted rate is deemed to be inclusive of fixing arrangement. 2. GI pipe of 40 mm dia will be measured and paid separately as supply only.

Supply only GI pipe (40 mm bore) light grade for fixing and supporting of Air termination single pointed aluminum rod & supporting GI strip complete all as specifie and directed.

Schedule of Credit

M/S Gulab Singh (BID ID -3207094)