PROVISION OF FENCING, TOILET BLOCKS AND CERTAIN E/M WORKS UNDER GE HADDO

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition of PCC block masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc., complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and as directed.

Excavating in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 50 metres and making good disturbed surfaces complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth, for foundation etc., or for shafts, wells, cess pits, manholes, pier holes etc not exc. 10 Sqm on plan and n.exc. 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and depth exceeding 1.5m but not exceeding 3.0m for foundation etc., or for shafts, wells, cess pits, manholes, pier holes etc not exc. 10 Sqm on plan and n.exc. 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth, for foundation etc., or for shafts, wells, cess pits, manholes, pier holes etc not exc. 10 Sqm on plan and n.exc. 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each as in soils complete all as specified and as directed.

Removing excavated material (soils) to a distance not exceeding 50 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Removing excavated material (soils) to a distance exceeding 50 metres but not exceeding 100 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Removing excavated material (soils) to a distance exceeding 250 metres but not exceeding 500 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Moorum/red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed. NOTE: Moorum shall be brought from outside MD land

M&L for hardcore using broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry exceeding 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry not exceeding 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs including weathering, slightly rounded or chamfered angles and throating including necessary form work, exposed surfaces of concrete finished even and smooth without using extra cement complete all as specified and as directed.

M&L for pre-cast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in cover slabs of manholes and drains and setting in cement mortar (1:4) complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in chajjas complete all as specified and as directed.

M&L for reinforced cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, cooking platforms and in shelves and the like complete all as specified and as directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns etc., (Square / Rectangular / Polygonal) for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces of concrete flat complete all as specified and as directed.

M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete flat complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube as per specification & drawing, fixed in opening complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with particle board core, 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm plain colour PVC sheet on back face as per specification & drawing fixed to door frame complete all as specified and as directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 complete all as specified and as directed.

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

M&L for Mild steel CRS/HCRM TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel CRS/HCRM TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for 10mm dia mild steel round bars cut to length, bent to shape required to be used as stifferners in chain link fencing, fixed independently to angle iron posts conforming to Fe 410 (Gde-E-250) quality 'A' or Fe 290 (Gde-E-165) complete all as specified and as directed.

M&L for mild steel framed work such as gates, grills, gratings, etc., with ornamental and intricate design, ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe-290 Gde E-165 including portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc., complete all as specified and as directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

M&L for mild steel angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc., conforming to Fe-410-W (Gde E-250) Quality 'A' complete all as specified and as directed.

M&L for mild steel hold fasts, bands, straps, supports or stays for rainwater, brackets/clamps for eaves/barge boards and valley gutter and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 5 cm but not exceeding 10 cm and dia of neck 11 to 15 mm complete all as specified and as directed.

M&L for mild steel galvanised PVC coated chain link fencing, 3mm nominal dia of GI wire, 1.4mm thick PVC coating and average area of aperture 25 Sqcm with weight of chain link not less than 2.0 Kg/Sqm, including line wires, fixed to any type of standards, rails, straining bolts, etc., including provision of binding wire complete all as specified and as directed.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based trapezoidal profile steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutters, fixed with self tapping screws including scoffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F aluminum flat iron wind ties of any size and thickness fixed with self tapping screws for fixing roofing sheets complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers.

M&L for anodised aluminium snap grid frame work for false ceiling with size of grid 605mm x 605mm all as specified in SSR Part-I 2009, hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat iron 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including cutting, drilling, jointing etc., 6mm thick non-asbestos fibre cement building design boards fixed or laid/ inserted to aluminium frame work with screws and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and as directed.

S&F 19/20mm thick plywood boarding, grade BWR, type BB as in eaves/barge boards fixed with screws on flat iron/timber frame work support complete all as specified and as directed.

S&F 20mm thick second class hard wood boarding as in eaves/barge boards fixed with screws in any situation, clean sawn with butt joints complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection, surface of concrete finished even and smooth using extra cement complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base of floors complete all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base of floors complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in floors complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4) type B0 (using 12.50mm graded stone aggregate) as in floors complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 9 to 10 mm thick (square/ rectangular) of approved shade, area of each tile not exceeding 0.36 Sqm as in floors etc., laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 9 to 10 mm thick (square/ rectangular) of approved shade, area of each tile not exceeding 0.36 Sqm, for work on vertical surfaces such as skirting, dados and risers to steps etc., including 10mm thick backing coat in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles in vertical surfaces using size of tiles 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 20mm thick granite work (of any type and shade as approved) table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms, wash basin counters and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite stone including grinding and polishing, rounding (chamfering) the edges complete all as specified and directed.

M&L for glossy finished chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:4) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in two coats 5mm thick in CM (1:4) mixed with integral water proofing compound @ 3% by weight of cement over 10mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

M&L for rendering 10mm thick in CM (1:4) mixed with integral water proofing compound @ 3% by weight of cement, on fair faces of brick work or concrete, surfaces finished even and smooth without using extra cement complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

Supply only integral water proofing compound.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of pink primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of external walls of any description and applying two coats of weather proof antifungal (exterior grade) acrylic emulsion over a coat of primer from the same manufacturer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of primer including one coat of wall care putty for smooth surface by grinding etc., complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for anodised aluminium partition, window and door/ventilator with frame and shutters and grill fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

SUPPLY ONLY 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with balancing white lamination complete all as specified and as directed.

S&F 19/20mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with balancing white lamination complete all as specified and as directed.

SUPPLY ONLY Imax hinges,stainless steel suitable for aluminium window shutters, fixed in repairs complete all as specified and as directed.

Supply only 6.0 mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only 3.0 mm thick figured glass, pin head type and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only aluminium expanded metal fly proof mesh, cut to required size and shape, with 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F 20mm dia mild steel PVC coated curtain rod with fancy type end brackets of any colour complete all as specified and as directed.

S&F sliding door bolt, 300mm long, aluminium alloy, anodised, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F door closer, aluminium (extruded section body), hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed with screws complete all as specified and as directed.

M&L for 15mm dia or bore galvanised steel tubing, medium grade, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

M&L for 20mm dia or bore galvanised steel tubing, medium grade, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

M&L for 50mm dia or bore galvanised steel tubing, medium grade, with all fittings and laid in trenches or fixed to walls and ceilings or laid in floors complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C2 (using 40mm graded stone aggregate) bed to drain pipes 100mm dia including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks, triple layered, ISI marked (cylindrical vertical with closed top), 1000 litres capacity, hoisted and fixed in position all as specified in SSR Part I, 2009 including 25mm dia or bore PTMT ball valve high pressure with epoxy coated aluminium rod & high density plastic ball (minimum weight 455gms) screwed for iron pipe, provision of 40mm/25mm spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

M&L for vitreous China wash hand basin, white, flat back, size 550mm x 400mm including cutting for and pinning in ends of brackets or erecting stand, 32mm dia waste coupling brass chromium plated, PVC waste pipe of suitable length, chain and plug, screwed down for iron pipe or for unions complete all as specified and as directed.

M&L for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests, P or S trap including provision of lime concrete bedding complete all as specified and as directed.

S&F 20mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron or CPVC pipe, fixed in repairs complete all as specified and as directed.

S&F bib tap, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule complete all as specified and as directed.

S&F pillar tap, brass, 15mm dia, chromium plated, fancy type with capstan heads, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.

S&F stop valves 15mm dia or bore, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

M&L for PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets and 32mm dia PVC flush pipe complete all as specified and as directed.

M&L for PVC connections 15mm size with PTMT nuts of length 600mm, fixed in repairs complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) bends with oval access door, any radius, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) branch piece with oval access door, single (single Y) equal or unequal, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) vent cowl of diameter 110 mm complete all as specified and as directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement, diameter of outlet 75mm complete all as specified and as directed.

S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190gms) complete all as specified and as directed.

S&F towel ring of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 90gms) complete all as specified and as directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and as directed.

Cutting 20mm dia existing steel tubing for alterations or additions (each cut measured) complete all as specified and as directed.

Taking down carefully old unserviceable aluminum/ copper point wiring (light, fan, socket or power) complete, including fittings & fixtures such as switches, ceiling roses, lamp holders, pendants, regulators sockets, light fittings, junction/terminal boxes etc; removing from site and making good disturbed surfaces of walls, floors etc., to match with existing surrounding surfaces complete all as specified and as directed.

Taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down existing unserviceable main switches/ distribution boards of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down carefully old unserviceable light fittings only and removing from site complete all as specified and as directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE LIGHT/FAN point controlled by one, one way 6 Amps switch.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE LIGHT/FAN point controlled by one, one way 6 Amps modular switch.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps modular switch on independent board.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps modular switch on same board with other switches.

M&L for Point wiring complete with 2.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC conduit of suitable size (not less than 20mm dia) medium grade and conduit accessories concealed in walls/ceilings etc., including provision of PVC insulated 2.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in modular type pressed steel terminal boxes of suitable modules made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint all over and modular cover plates with frames on top for suitable modules on top for housing switches, sockets etc., all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps modular switch on independent board.

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M&L for Sub main wiring complete with four runs (3P+1N) of 10.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and two runs of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Four runs of 10.0 Sqm copper conductor, two runs of 6.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M&L for LTUG XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 2 core, 16 Sqmm laid in trenches/floors/ducts or fixed on poles/walls with suitable clamps/saddles or drawn through pipes etc., including connecting up with suitable size of lugs, glands and jointing material complete all as specified and as directed.

M&L for LTUG XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 3½ core, 70 Sqmm laid in trenches/floors/ducts or fixed on poles/walls with suitable clamps/saddles or drawn through pipes etc., including connecting up with suitable size of lugs, glands and jointing material complete all as specified and as directed.

S&F switch piano, flush type, single pole, one way, 6 Amps, 240 volts complete all as specified and as directed.

S&F modular switch, one way, one module, single pole, 6 Amps complete all as specified and as directed.

S&F modular socket, multipurpose, 2/3 pin combined, 2 module, single pole, 6 Amps complete all as specified and as directed.

S&F modular socket, multipurpose, 2/3 pin, 6/16 Amps combined, 2 module, single pole, complete all as specified and as directed.

S&F modular switch, one way, one module, single pole, 16 Amps complete all as specified and as directed.

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 6A, 240 volts complete all as specified and as directed.

S&F ceiling fan of three blades metallic colour, remote controlled, 1200mm sweep, 360 RPM, suitable for AC 230 volts, heavy duty with down rod and canopies complete all as specified and as directed. MAKE: GORILLA Model: GOLDEN OAK WOOD

S&F exhaust fan, 250mm (10") sweep, plastic body with louvers complete all as specified and as directed. MAKE: CROMPTON GREAVES, Model: VENTIUS or equivalent in ORIENT/HAVELLS

S&F LED tube light fitting, 1x20 watts, 230 volts, 50Hz AC supply, with high power and high efficiency long life LEDs with built-in electronic driver, fixed on walls and provision of 3 core, 1.5 Sqmm copper cable from ceiling rose to connector of fitting complete all as specified and as directed. MAKE: PHILIPS Cat Part No. BN150WLED20S6500PSE0DGR or its equivalent in HAVELLS/CROMPTON/C&S

S&F LED security light fitting, 1x25 watts, 230 volts, 50Hz AC supply, with high power and high efficiency long life LEDs with built-in electronic driver, unique peanut lens to ensure uniform distribution completely housed including suitable down rod and fixed on walls including MS clamps (02Nos) made up of 40mmx5mm MS flat, nuts, bolts and washers and provision of 3 core, 1.5 Sqmm copper cable from ceiling rose to connector of fitting complete all as specified and as directed. MAKE: PHILIPS Cat Part No. BRP020LEDHP/CW240V25/ CROMPTON Cat Part No. LSTS-25-CDL or its equivalent in HAVELLS/C&S

S&F LED post top luminaire, outdoor type (Prince opera midi) of 240 Volts, 50Hz, 40 watt capacity, IP 65 protection including mounting on 63mm dia galvanised medium grade pipe of 2.0 metre height from GL with necessasry PCC (1:2:4) type B1 foundation and connecting up with and including 3 core 2.5 Sq mm multistranded copper conductor cable drawn through 25 mm dia rigid PVC conduit complete all as specified and as directed. MAKE:CROMPTON GREAVES Cat part No. LPTO-40-CDL or equivalent in PHILIPS/C&S/ HAVELLS

S&F MCCB DB sheet steel enclosure, VTPN, 4-way, double door, 415 Volts with 200 Amps rated bus bar, IP-43 protection suitable for incoming MCCB 160/200 Amps and outgoing MCB TP, cement spill protector concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed. MAKE: L&T/ LEGRAND/ SIEMENS/ INDO ASIAN/ HAVELLS

S&F MCB DB, SPN, 4-way, vertical type, double door, 240 Volts with 200 Amps rated bus bar, IP-43 protection, shrouded neutral bus bar, cement spill protector, concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed.

S&F MCCB, 4 pole, 100 Amps, 50Hz, 25KA rupturing capacity, 415 Volts adjustable type with thermal and magnetic release complete all as specified and as directed. MAKE: L&T/ LEGRAND/ SIEMENS/ INDO ASIAN/ HAVELLS

S&F MCB, DP, "C" series, 230 volts, 40 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811174 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

S&F MCB, SP, "C" series, 240 volts, 6 to 32 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811129 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

S&F MCB, SPN, "C" series, 230 volts, 63 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811154 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

S&F decorative cute lines LED light fixture of 20 Watts capacity, 6000K, 230 Volts, 50 Hz AC supply, warm white with extruded aluminium heat sink, environmental friendly energy efficient light fitting, surface mounted including 20 Watts LED lamp and testing complete all as specified and as directed. MAKE: PHILIPS Cat part No. BN150WLED 20S-6500PSEODGR or equivalent in HAVELLS/ WIPRO/CROMPTON GREAVES

M&L for chemical earthing complete with copper earth plate electrode of size 900mmx600mmx5mm thick buried directly in ground (earth pit not less than 3.0m deep below the normal ground level) with top edge of the earth plate not less than 2.25m below normal ground level connected to 32x6mm copper earth strip as earth lead connected by means of bolts, nuts, washers and check nuts made out of copper by proper treatment of jointing surfaces or by brazing and connected to main switch board/ electrical equipment upto 7.5 metre away from earth electrode including 20mm dia medium grade GI watering pipe, sodium chloride (common salt), magnesium and copper sulphate, salt and soft coke/charcoal in suitable proportions (Charcoal- 100 kg, Copper sulphate-120 Kg, Crystal salt-100 Kg, Magnesium sulphate-100 Kg) laid in minium five layers alternately. A funnel with wire mesh shall be provided on top of watering pipe. The funnel attachment shall be housed in concrete with PCC (1:2:4) type B1 chamber, with cast iron mild steel frame and cover having locking arrangement suitably embedded in the masonry enclosure, finished flush with ground level etc including necessary excavation in any type of strata, returning, filling removing of soil outside MD land, filling of charcoal and salt complete all as shown in electrical plate No.3 of MES Sch Part-I, connected to earthing test point all as specified and directed and testing complete for resistance less than 01 Ohm on completion. NOTE : (i) Unit rate quoted deemed to include for Copper plate and necessary Strip connections upto 7.5 mtrs along with PCC / CI chamber, water funnel along with cover and protection pipe and excavation and returning and refilling of soil. (ii) Contractor should submit test results of earthing after completion of earth pit.

M&L for earthing complete with GI earth plate electrode of size 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5m below normal ground level connected to 4mm dia GI earth wire as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 3 of SSR Part-I connected to common earth dolly including testing on completion complete all as specified and directed. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 422 & 423 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

S&F copper strip 32x6mm fixed with saddles and screws etc., as in roof conductors and down conductors above ground level complete all as specified and as directed.

M&L for test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. of 8mm dia, 25mm long hexagonal head screw complete all as specified and as directed.

M&L for GI sheet/ SMC box of size 150x150x75mm, made out of 2mm thick fixed on walls with necessary wooden gutties/rawl plugs, brass bolts, nuts and washers or brass screws complete all as specified and as directed.

M&L for security/street light mounting bracket made up of 40mm dia galvanised steel tubing, medium grade, 1.20 metres long, bent to shape with inner angle not less than 120°, with and including necessary fixing clamps fabricated out of angle iron/flat iron of suitable size, bolts, nuts and washers as required and applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

Supply, install, test & commissioning of Split type air conditioner, 1.5 TR capacity, 5-Star rating, EER 3.2 having cord less remote control unit, wall mounted inverter type with built-in ioniser and plasma filter for better air quality, copper wound, electric driven, single phase, 240 volts, 50 Hz, AC supply including transporting to site, fixing of indoor and outdoor units with necessary wall mounting brackets, necessary copper piping minimum 8 RM for connections, cutting, bending, brazing, proper insulation on copper pipe and all other pipes, PVC drain pipe upto ground level, installation complete with all accessories including connecting electrically between indoor and outdoor units with suitable size of PVC insulated multistranded copper conductor, 01 No spare PCB for each AC complete all as specified and as directed. MAKE: BLUESTAR Model: 3HW185ATU or equivalent in VOLTAS/LG/HITACHI NOTE: All connected pipes shall be covered with PVC casing and capping.

S&F Electronic voltage stablizer of 4 KVA capacity, wall mounting type having features such as Intelligent time delay system of 2 to 4 minutes, low and high voltage cut-off protection, latest IC technology to protect from power fluctuations, thermal over load protection, wide input variation between 165 Volts to 295 Volts with output voltage stablized at 200 Volts to 240 Volts, with accuracy of +2.5% suitable for split type airconditioner complete all as specified and as directed. MAKE: V-GUARD, Model-

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB "C" series, 240 volts, 6 to 32 Amps, 10 KA rupturing capacitycomplete all as specified and as directed.

M/S VISHAL CONSTRUCTION

BHARAT MULTITECH INDUSTRIES PVT LTD

M/s Ramesh Lal