PROVISION OF REV WORKS / SPECIAL REPAIR WORKS IN AFTC AND AFS UNDER GE M AF JALAHALLI BANGALORE

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding along with screed bed / plaster, removing serviceable tiles to stores and rubbish off the premises all as directed by Engg in charge

Material and labour for 40mm thick PCC 1:2:4 type B-1 using 20mm graded agg as in flooring

Material and labour for 15mm tick screed bedding layer in cement mortar 1:4 surface is to be prepared to receive floor finishes.

Material and labour for Machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006 of 80mm thickness, M-40 grade with grey cement and not pigment interstices all as specified and directed.

Material and labour for Machine pressed precast conctete interlocking paver block using grey cement and with pigments any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including dismantling of old tiles complete all as specified and directed.

All as item No 5 above but except tiles

Material and labour for pre-cast cement concrete block masonry type C1 1:3:6 (20 mm graded aggregate) with soild blocks, exc 10 cm width and setting in CM 1:6

Material and labour for pre-cast cement concrete1 :3 : 6 type C1 using 20mm graded stone aggregate block masonry with solid blocks, exc. 10 cm in width and setting in mortar, built in cement mortar 1:4

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished faiar and even without using extra cement

Material and labour for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting.

Material and labour 15mm thick rendering in CM (1:4) on brick or concrete wall surface finished even & fair without using extra cement as in Wall with water proofing compound as per manufacturer instruction etc complete.(Water proofing compound measured and paid separately).

Material and labour for Pre-cast cemnet concrete 1:2:4 , type B1 (using 20mm hraded granite stone aggregate) in landing, cover slabs (for self's/working platform etc.) shelves and similar articles with plain faces and set in cement mortar 1:4.

Material and labour TMT bars 10mm diaFe-410-W (Gde E-250) quality A or Fe 290 (Gde-E-165), and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS

All as per item No 13 above but 5mm and over upto and including 10mm dia TMT bars in stirrups, spaces and binders

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and mirror polishing all as specified and directed

Material and labour joint free Non skid ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm , in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match.

Material and labour Coloured Glazed ceramic tiles 450 X 300 X 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to matchall as specified and directed

Supply and fixing 1.5mm thick stainless steel sink of size 900mm x900mm x 600mm for kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union pipe complete all as specified and directed by Engr-in-Charge (Note: The entire station should be 304 stainless steel polished and ground)

Preparing old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying a two coat of distemper oil emulsion on surfaces of walls.

Supply and fixing 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

Supply and fixing 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors.

Material and labour for PVC (SWR) Floor trap / Nahani traps of 75 mm outlet plain with grating including jointing with solvent cement.

Supply and fixing in repairs 15 mm fancy type bore chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.

Supply and fixing 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

Supply and fixing 20mm Gun -metal , globe or gate valves, with iron wheel head, screwe both ends for iron pipe and fixed.

Material and labour for 75 mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls .

Supply and fixing 75 mm dia.,PVC Bends (any Radius) with access door

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) any thickenss, including cover fillets.

Supply and fixing Anodised aluminium snap grid frame (powder coated) work for false ceiling 605mmx605mm T angle 1.5mm thick complete all as specified.

Material and labour for Hangers 4 to 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means ofceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners12.5mm dia. 40mm long complete all as specified

Material and labour for providing and fixing pre- painted Gypsum board/tiles 9 mm thick in ceiling insulation and acoustic purposes, 600 x 600 mm in size, fixed with screws to aluminium frame work or with staples on snap grid in ceiling and as per manufacturers instructions.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/Dense soil.

Material and labour Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified

Demolition of brick work built in cement mortar or cement lime mortar

Demolition of cement concrete of any description and in any position not otherwise specifically provided for.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of internal dia 150mm

Supply only Inegral waterproofing compound

Cutting into existing manholes for connecting new drains pipes, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Material and labour for Plain Cement Concrete Type B0 1:2:4 (using 12.5mm graded granite stone aggregate) cast in situ in, plinth courses, copings, bed plates benching and the like including weathering, slightly rounded or chamfered angles and throating, as directed and finishing the concrete surfaces even and smooth without using extra cement

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitered / stopped ends etc complete..

Material and labour 150mm bore of reinforced concrete pipes, class NP2 and jointed complete with collars laid in trenches and jointed as specified.

Material and labour for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point.

Precast cement concrete 1:2:4 type B1 (Using 20 mm graded granite stone aggregate) in landings, cover slabs (for man holes etc) chullah hoods, chajjas, water troughs managers, shelves and similar articles with plain faces and set in cement mortar 1:4

Supply and fixing for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings running rails and guides) and hanging; also fastening and Fe 410 -W (GdeE- 250) quality fixing complete

Material and labour for 75 mm thick 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of flooring.

Material and labour 50 mm thick sand filling under floors or in foundations including watering and consolidation.

Removing building materials etc. to a distance of n exceeding 5 KM ,beyond the lead included in the rates, including loading, unloading and stacking at the destination.

Plugging to walls complete, for wood fillets, grounds, moulding, boarding, etc.,

Material and labour for 18/19mm thick Block boards, grade 2 quality, exterior grade, commercial type, fixed with screws to timber frame-work

Supply and fixing 0.90mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

Material and labour for 19/20mm thick block boards external teak wood lipping, 6mm thick fixed with nails

Supply and fixing 75mm projected hinges stainless steel fixed with screws to wooden shutters

Supply and fixing 75mm long Aluminium anodised, barrel tower bolts of extruded section and fixed

Supply and fixing 100mm long extruded Aluminium alloy handles, fabricated type anodised

Supply and fixing brass locks cup board grade I, size 50mm

Supply and fixing Ball catches with 8mm dia steel ball, and brass body and striking plate including lettering in hand & fixed

Cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required supercial area Exc. 400 sq. cm

Material and labour for Excavating in post holesin hard/dense soil (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

Supply and fixing for 40mm dia stainless steel tube grade 304 vertical posts 900mm high welded with 150mm high AF emblum over 3mm thick 125mm dia SS plate and 4mm dia SS rings on either side for fixing chains complete all specified as directed

Supply and fixing 4mm dia SS chains 25mm X 40mm grade 304 complete fixing to vertical posts

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard/dense soil.

Material and labour cement concrete 1:2:4 type B1 in pilasters, buttresses columns, pillars, boundary pillars and posts.

Material and labour for RCC 1:2:4 type B1 using 20mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

Supply and fixing for Steel work in tubular tru-sses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

Supply and fixing for Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Supply and fixing for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Material and labour for preparation of surfaces of any description, over 10cm in width or grith, not otherwise described and applying two coats of Synthetic enamel paint over a coat of red oxide primer on steel surfaces.

Material and labour for hardcore with broken ganite stone boulders of size not exc 63mm size spreaded rammed or rolled to true surface

Material and labour for 50mm thick Cement concrete type B-2, 1:2:4 using 20mm graded aggregate as in flooring surface is to be finished even and smooth without using extra cement

Material and labour Formwork to sides of pillars,posts, struts, piers, columns and stanchions rough finished surfaces.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3

Supply and fixing for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with Welded attachment

S R Trading Co

LAKSHMI CONSTRUCTIONS

K. VENKATESH NAIDU

ARATHEERTHA CONCEPTS

SRI MAHALAKSHMI CONSTRUCTIONS

chowdeshwariconstructionco

OM CONSTRUCTIONS

shashi shekar construction

Maruthi constructions