Providing and applying painting to the existing surfaces and some minor repairing works at various locations inside BARC, Trombay, Mumbai.

Amount

Providing and Painting two coats of synthetic enamel paint on steel surfaces of approved brand and manufacture to give an even shade over a primer coat, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

Providing and applying two coats of water based high build anticarbonating coating over sealer to exteriors on Cement pointing wall/Cement concrete wall and cement concrete Y posts in coastal/sea side area to high vehicular gas emissions with total thickness of 200 microns as per manufacturer's specifications to give an even shade including removing all deposited salt, articles,dust, grease, moss, loose materials etc. if any by watering , scrapping the uneven surfaces and filling the damaged /honeycombed surface, etc. if any with the help of applying grey cement paste , grinding up to smmoth finished, cleaning, cutting of vegetations , dismantling of loose pointing if any, with necessary scaffolding etc. complete as directed. Note :- (1) Minimum Consumption of all coats should be done at site as per range given in manufacturer's specifications. (2) The cost of scaffolding, cutting of wild vegetations and applying of cement paste to the rough surface is included in this item. (3) For painting over cement pointing surface the area will be increasing by 20 % over plain area surface.Tentative Suggested Make of anticarbonating coating & Sealer :Anticarb High build or its equivalent make

Providing and applying white cement based wall putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge .

Providing, painting,finishing walls with two coats of anti-algae, weather proof acrylic smooth emulusion paint of approved make with silicon additives on sand face plaster/ plain plaster & concrete surfaes of required shade over new work over a base coat of exterior cement primer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge.

Providing and Painting with Epoxy PU paint using 2 coats of (120 Micron dry film thickness) Epoxy PU high build coating as finishing coat over a priming coat of High Build primer of 50 micron thickness over steel surfaces at all locations prepared and applied as per specifications including preparation of surface by cleaning with wire brush and rubbing, scraping , applying sand paper , making free of Rust, dust, dirt etc. filling the holes, joint, cracks if any using epoxy putty complete. all as per manufacturers technical data and as directed at site to achieve minimum overall dry Film thickness of 170 micron (50 Micron primer Coat + 120 micron finishing Coat). On STEEL surfaces Tentative suggested make of high build primer : EPILUX-13 or approved equivalent

Painting road surface marking with Thermoplastic paint hot applied to give uniform finish with Glass beeds / power Topping, on bituminous surface in white / yellow shade including cleaning the surface of all dirt, scales, oil, grease and other foreign material etc complete as directed by the Engineer-in-charge (a) Thermoplastic paint on bitumen sufaces.

Dismantling Kerb stone carefully without damaging the stone, including removal of earth, base pcc etc. and refixing the same in line and level on newly laid base PCC 1:3:6 and pointing the exposed faces in cement mortar 1:3, curing etc. complete as directed by the Engineer in charge. The rate shall also include charges for disposal of unserviceable materials within 50 m lead. The base PCC laid shall be paid separately under relevant item.

Providng and fixing at and near ground level precast cement concrete 1:2:4 in kerbs, edgings etc. as per approved patterns and setting in position with C.M 1:3 (using crushed sand) including consolidation, curing, cost of required centering, shuttering, finishing smooth with 6 mm thick cement plaster 1:3 (using crushed sand) on exposed surfaces complete as per specifications and as directed by the Engineer-in-charge.

Labour charges for dismantling existing shahbad stone pavement in footpaths, in Plinth Protection etc. carefully without damaging and re-laying the same over a bed of stone grit 150mm consolidated thickness, to proper slope, including cutting the edges to proper lines and sunk pointing with Cement mortar 1:3 with 15mm x 10mm groove cross wire and longitudinally and curing etc. complete (Grit to be provided by the Contractor).

Providing and fixing Rough Shahbad Stone of minimum 50 mm average thickness of size 600 X 600 mm (Approximate) over 150 mm thick (consolidated thickness) stone dust backing including setting in position in footpath to the required level and line Pointing with C.M 1:4 (using crushed sand). Joint shall be 20 to 25 mm wide including filling of joints with cement mortar and making grooves etc. complete as per the direction of Engineer-in-charge.

Providing and laying in position cement concrete of 1:3:6/M-10 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels.

Providing and laying in position cement concrete of 1:2:4/ M-15 with minimum cement content 320 Kg/Cum (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels .

Extra for RCC/PCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants. Note:- (i) In view of limit on water-cement ratio for durability requirements, concrete admixtures (Naphthalene / Melamine based super plasticizers) shall be used after taking prior approval of Engineer-in-Charge and the rates quoted for these items shall be inclusive of the cost of admixtures, trial mixes, testing (at site & at approved labs), etc. complete. Note:-Retention of slump for piling work shall be 150 mm after two hours.

Supplying man power along with necessary pans, spades, shavels pickaxe, punjas, ropes, smallspecial spade etc. upto maximum any numberof labour as and when decided by Project Engineer to work for eight hours per day or monsoonperiod to carry out the cleaning/scrapping and brushing to existing rusted ms railing, marking of numbers on new RCC precast wall and also carry out seasonable departmental work allotted byProject Engineer from time to time.

RESHMA CONSTRUCTION

B.L.Waghmare Baba & Co

ORIENTAL INTEGRATED FACILITY MANAGEMENT PVT. LTD.