Providing and fixing of MS chowckats, tile work, stone work and other misc. works in Kaveri Girls Hostel at MDU, Rohtak

Amount

Removing door and windows (wood and steel ) with chowkats by making recesses in walls when the wall is not to be dismantlled. Doors

Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hings, confirming to PWD specifications, including bolts for fixing stops, locknutch, provision for receiving tower bolts and finished with one coat of ready mixed paint red lead non setting primer of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (a) Door and window frame of size 89mmx50mm with 40mm wide single rebate

Providind and fixing 1st quailty ceramic glazed wall tiles confirming to I.S 15622 (thick ness to be specified by the manufactureer) of appreved make in all colors shades except burgundy, bottle green, black of any size as approved by Ebgineer-InCharge in skirting risers of steps and dados over 12 mm thick bad of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matchine shades complete. Size of ceramic Glazed tiles 200X300mm

Factory manufactured solid flush door shutters, with block board core as der I.S. No. 1659-1669 bonded with water, proof type danol formaloehyde synthetic resin, hot-press as , conforming to I.S. 2202 part-I and II fixed in position including iron hinges screws chocks/cleats and stops, etc. (Excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) Note:- Commercial veneering with vertical grains or cross bands and face vaneer on both sides comercial facing with laminated core and lipped edges. Duro, Green make 30 mm. Thick

Providing and fixing in position best indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 Nos chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P brass screws ( as required by the Engineer-in-charge) complete including cutting and making good the walls etc. indian make (i) 600mm X450 mm

Wrought iron and mild steel ( using angles, flats, square bars, tee and channels) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position

Cement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects.

Steel reinforcement TMT bars FE-500 EQR/FE-500D grade or more for RCC wrok, where no included in the complete rate or RCC including straightening, bending, binding, wastage,overlaps,welded joints,spacer bars,chairs,stays,hangers and annealed steel wire etc. and heights/depths/storeys/basements etc. Note. Reinforcement shall be measured in length indluding hooks, if any, separately for different diameters as accuslly used in work, excluding overlaps. wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.

Applying priming coat with ready mixed exterior paint in all shades on newly plasterd or concrete exterior surface.

Providing, Laying and fixing Granite Stone in all Shades 15 mm to 18 mm thick in flooring, Skirting, Dado etc laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with whicte cement slurry mixed with pigment to match the shade of granite stone complete in all respect to complete satisfaction of Engineer-in-charge.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm (+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size(5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. complete in all respect as per entire satisfaction of Engineer-in-Charge.(DSR 12.50)

Pawan Kumar