PROVISION OF FURNITURE FOR CONSTRUCTION OF OFFICER MARRIED ACCOMODATION SINGLE UNIT AT NAGPUR UNDER GE KAMPTEE

Amount

3 Door wardrobe (size 1275 mm x 600mm x 3275 mm) Drawing No. CWE / NAG / SK / 1(a) / 2024 Note:- The item shall be consist of details given as under: SERVANT BEDROOM (WARDROBE) (a) Wardrobe shall have 19mm thick pre-laminated particle board in soffit sides, shelves, drawer and bottom. (b) The wardrobe shall consist of size 1275x600x3275 mm. All as shown in drawing. (c) Shoe drawer in both units shall be provided of height 300mm all as shown on drawings at bottom of wardrobe. (d) The drawers of height 250mm shall be provided on top of shoe drawer. A drawer and locked drawer each of 150mm height and divided into equal parts width wise shall be provided above it. (e) A hanging space of 975 mm height shall be provided all as shown on drawings. A 20 mm dia hanging rod shall be provided with brackets at both the ends. (f) Two open shelves of height 250mm each shall be provided on top of hanging space. Luggage space 900mm height shall be provided on top of units. (g) Shutter shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be subdivided in sizes as shown on drawing.

3 Door wardrobe (size 2100 mm x 600mm x 2950 mm) Drawing No. CWE / NAG / SK / 1(b) / 2024 Note:- The item shall be consist of details given as under: BEDROOM NO- 01 (WARDROBE) :- (a) Wardrobe shall have 19mm thick pre-laminated particle board in soffit sides, shelves, drawer and bottom. (b) The wardrobe shall consist of 2100x600x2950mm. All as shown in drawing. (c) Shoe drawer in both units shall be provided of height 225 mm all as shown on drawings at bottom of wardrobe. (d) The drawers (02 nos) of height 250mm shall be provided on top and shoe drawer. A open shelf (01 nos) and locked drawer (01 nos) each of 225mm height and divided into equal parts width wise shall be provided above it. (e) A hanging space of 950mm height (02 nos) shall be provided all as shown on drawings. A 20 mm dia hanging rod shall be provided with brackets at both the ends. (f) Four open shelves of height 250mm each shall be provided on top of hanging space. Luggage space (02 Nos) 550mm height shall be provided on top of units. (g) Shutter shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be subdivided in sizes as shown on drawing.

3 Door wardrobe (size 1550 mm x 600mm x 3150 mm) Drawing No. CWE / NAG / SK / 1(c) / 2024 Note:- The item shall be consist of details given as under: BED ROOM NO- 02 (WARDROBE) :- (a) Wardrobe shall have 19mm thick pre-laminated particle board in soffit sides, shelves, drawer and bottom. (b) The wardrobe shall consist of size 1550x600x3150mm. All as shown in drawing. (c) Shoe drawer in both units shall be provided of height 300mm all as shown on drawings at bottom of wardrobe. (d) The drawers (02 nos) of height 250mm shall be provided on top of shoe drawer. A drawer and locked drawer each of 150mm height and divided into equal parts width wise shall be provided above it. (e) A hanging space of 975 mm height shall be provided all as shown on drawings. A 20 mm dia hanging rod shall be provided with brackets at both the ends. (f) Two open shelves of height 250mm each shall be provided on top of hanging space. Luggage space 750mm height shall be provided on top of units. (g) Shutter shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be subdivided in sizes as shown on drawing.

4 Door wardrobe (size 750 mm x 325mm x 2350 mm) Drawing No. CWE / NAG / SK / 1(d) / 2024 Note:- The item shall be consist of details given as under: 04 DOOR WARDROBE OFFICE:- (a) 04 door wardrobe shall have 19mm thick pre-laminated particle board in soffit sides, shelfs and drawers except open shelf which shall be 12mm thick glass bottom. (b) 04 door wardrobe shall consist of size 750x325x2350mm. All as shown in drawing. (c) A luggage space of 675mm height shall be provided all as shown on drawings. (d) Four open shelves of 12mm thick glass height 332x350x550mm shall be provided on top of luggage space all as shown on drawings. (e) Shutters shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be sub divided in sizes as shown on drawings.

King Size Bed (size 7' x 6' 7") Drawing No. CWE / NAG / SK / 3(a) / 2024 Note:- The specifications of king size bed shall be of specification as given below :- (a) The entire material except particle board shall be made of class-I hard wood of teak wood. (b) The bed shall contain members which are short leg, long leg, short rail, long rail, head rest, bottom stiffener, middle stiffener (which is supported on a two way member joining long and short rail ). (c) The dimensions of various members is given in the drawing. In addition certain other details as mentioned below:- (i) Short leg :- The short leg shall be circular moulded in shape and its circumference at the centre shall be 125 mm and it shall be moulded as shown in the drgs list opposite at top & bottom. Exact location where moulding/carving is to be done is given at drgs. (ii) Long Leg :- The long leg shall be circular in shape in middle with gradual tapering towards the top. The circumference at the centre shall be 125 mm and it shall be moulded as shown in the drgs list opposite at top & bottom. Exect location where moulding/carving is to be done is given at drgs. (iii) Short rail :- The Short rail will have min thickness of 1.5 inches and width of 6 inches and length of 6’ 7’’ feet. (iv) Long rail :- The long rail will have min thickness of 1.5 inches and width of 6 inches and length of 7 feet. Contnd.... 2.01

Contd 2.00 (v) The frame shall be made by members in such a manner so as to fit the mattress of size 7’ x 6’7” using the members mentioned above. (vi) The stiffeners as shown in the drgs shall be of size 2” x 4”. Its ends shall be keyed by tongue and groove joint and the same shall not be visible on the external side of the frame. (vii) The stiffeners should be placed on two way members made of teak wood of size 2“x 4“ and these shall be keyed by tongue and groove joint and the same shall not be visible on the external side of the frame. (viii) Head Rest :- The head rest shall be of thickness 2” width 6’7” and height 2 feet. The head rest shall have certain moulding and carvings as shown in drgs. It should be keyed by tongue and groove joint with long legs and the same shall not be visible on the external side of the frame. (ix) The carvings and mouldings shall be made as per drgs or as directed by Engr -in-charge/ Garrison Engineer. (d) The particle board shall be of size suitable to fit inside the frame of the king Size Bed (Preferable single piece, not more than two pieces). The specifications of Particle board shall be as per Zonal Specifications given in CA. (e) Polish:- The entire bed except particle board shall be polished in chestnut brown colour using melaminepolish as per zonal specification. (f) Hard rubber ring/toe shall be provided.

King Size Bed (size 6' x 6' 6") Drawing No. CWE / NAG / SK / 3(b) / 2024 King Size Bed :- Overall size of the bed shall be 6’ wide and 6’6’’ long and its height shall be 1’8’’ at the bottom of particle Board. The specifications of king size bed shall be of specification as given below :- (a) The entire material except particle board shall be made of class –I hard wood of teak wood. (b) The bed shall contain members which are short leg, long leg, short rail, long rail, head rest, bottom stiffener, middle stiffener (which is supported on a two way member joining long and short rail). (c) The dimensions of various members is given in the drg. In addition certain other details as mentioned below:- (i) Short leg :- The short leg shall be circular moulded in shape and its circumference at the centre shall be 100 mm and it shall be moulded as shown in the drgs list opposite at top & bottom. Exact location where moulding/carving is to be done is given at drgs. (ii) Long Leg :- The long leg shall be circular in shape in middle with gradual tapering towards the top. The circumference at the centre shall be 100 mm and it shall be moulded as shown in the drgs list opposite at top & bottom. Exact location where moulding/carving is to be done is given at drgs. (iii) Short rail:- The Short rail will have min thickness of 1.5 inches and width of 6 inches and length of 6 feet. (iv) Long rail :- The long rail will have min thickness of 1.5 inches and width of 6 inches and length of 6’6’’ feet. (v) The frame shall be made by members in such a manner so as to fit the mattress of size 6’ x 6’6” using the members mentioned above. Contnd.... 3.01

Contnd.... 3.00 (vi) The Stiffeners as shown in the drgs shall be of size 2” x 4”. Its ends shall be keyed by tongue and groove joint and the same shall not be visible on the external side of the frame. (vii) The stiffeners should be placed on two way members made of teak wood of size 2“x 4“ and these shall be keyed by tongue and groove joint and the same shall not be visible on the external side of the frame. (viii) Head Rest:- The head rest shall be of thickness 2” width 6’ and height 2’ feet. The head rest shall have certain moulding and carvings as shown in drgs. It should be keyed by tongue and groove joint with long legs and the same shall not be visible on the external side of the frame. (ix) Foot Rest :- The foot rest shall be of thickness 1.5” width 6’ and height 2’ feet. The foot rest shall have certain moulding and carvings as shown in drgs. It should be keyed by tongue and groove joint with long legs and the same shall not be visible on the external side of the frame. (x) The carvings and mouldings shall be made as per drgs or as directed by Engr -in-charge/Garrison Engineer. (d) The particle board shall be of size suitable to fit inside the frame of the king size bed (Preferable single piece, not more than two pieces). The specifications of Particle board shall be as per Zonal Specifications given in CA. (e) Polish:- The entire bed except particle board shall be polished in chestnut brown colour using melamine polish as per Zonal Specification. (f) Hard rubber ring/toe shall be provided.

Book case Wooden (size 1125mm x 475mm x 2400mm) Drawing No. CWE / NAG / SK / 4(a) / 2024 Note: The specifications of book case wooden shall be of specification as given below:- (a) Book case wooden shall have 19mm thick pre-laminated particle board in soffit sides and bottom shelves. (b) The book case wooden shall consist of size 1125x475x2400mm. All as shown in drawing. (c) 06 open shelves of size 393mm x 385mmx 392mm shall be provided on right side of book case wooden. (d) A luggage space of 1325mm height shall be provided all as shown on drawings. (e) Two open shelves of height 500mm each shall be provided on top of luggage. (f) Shutter shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be sub dived in sizes as shown on drawing.

Book case Wooden (size 750mm x 325mm x 2350mm) Drawing No. CWE / NAG / SK / 4(b) / 2024 Note:- The specifications of book case wooden shall be of specification as given below:- (a) Book case wooden shall have 19mm thick pre-laminated particle board in soffit sides and bottom except open shelves which shall be 12mm thick glass. (b) The book case wooden shall consist of size 750x325x2350mm. All as shown in drawing. (c) A luggage space of 675mm height shall be provided all as shown on drawings. (d) 04 open shelves of 12mm thick glass height 332mmx350mmx550mm shall be provided on top of luggage space. (e) Shutter shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be sub dived in sizes as shown on drawing.

Display Show Case Drawing No. CWE / NAG / SK / 07 / 2024 Note:- The specifications of display show case shall be of specification as given below:- (a) Display show case shall have 19mm thick pre-laminated particle board in soffit sides, bottom and shelves. (b) The Display show case shall consist of size 3361x600x800 mm and 3000x600x800 mm All as shown in drawing. (c) Shutter shall be provided all as shown in drawing at display show case . the shutter of height 800mm shall be provided. (d) A space of 600mm height from cooking platform. (e) Shutter shall be made of 19mm thick pre-laminated particle board of approved shade and colour shall be sub dived in sizes as shown in drawing.

Sofa Set 03 Seater Drawing No. CWE / NAG / SK / 11 (a) / 2024 Note:- The specifications of sofa set 03 seater shall be of specification as given below :- Overall size of the sofa set 3 seater shall be 5’ long 1’6” wide and its height shall be 1’3” at the top of the ply board. The specifications of sofa set 3 seater shall be of specification as given below. (a) The entire material except ply board (on which cushion is placed) shall be made of class-I teak wood. It shall have members i.e 02 Arm rest, long rail, short rail, wooden bearer (which is needed to support ply board). (b) The dimensions of various members are given in the drawing. In addition certain other details as mentioned below. (c) Legs-04 :- The legs shall be of length 1.5 feet and dimensions 3 inch x 3 inch. There shall be certain mouldings and carvings which are as shown in the drawing. Exact location where moulding/carving is to be done is given at drawings. (d) Short rail:- The short rail will have min thickness of 1.5 inches and width of 3 inches and length of 1’6”. (e) Long rail:- The long rail will have min thickness of 1.5 inches and width of 3 inches and length of 5’. (f) The frame shall be made by members in such a manner so as to fit a cushion of size 1’6” x 5’ using the members mentioned above. (g) The wooden bearers as shown in the drawings shall be of size 18”x60”. Its end shall be keyed by tounge and groove joint and the same shall not be visible on the external side of the frame. Contnd.... 6.01

Contnd.... 6.00 (h) Arm Rest:- The arm rest shall be of thickness 1’ 5” , width 1’ 6” and height 7”. The arm rest shall have certain moulding and carvings as shown in drawings . It should be keyed by tounge and groove joint with long legs and the same shall not be visible on the external side of the frame. (i) The carvings and mouldings shall be made as per drawing or as directed by Engr- in –charge/ Garrison engineer. (j) The ply board shall be of size suitable to fit inside the frame of the sofa set 3 seater (preferably single piece) The specification of ply board shall be as per zonal specification given in CA. (k) Cushion:- The cushion shall be provided inside the frame of bed bench of 4” thickness and it shall be of 32 density covered with best quality tapestry cloth as directed by E-in-charge/GE. The cost of Tapestry cloth shall not be less than Rs. 400 per sqm. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (l) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (m) Polish:- The entire sofa set except ply board shall be polished in chestnut brown. (n) Hard rubber ring/toe shall be provided

Sofa Set single seater Drawing No. CWE / NAG / SK / 11 (b) / 2024 Overall size of the sofa set single seater shall be 3’ high 1’6” wide and its length shall be 1’6” All the members of the chair shall be made of class-I teak wood. The specification of chair shall be as given below:-. (a) It shall have members i.e 02 Rear legs, 02 front legs extended to form back rest, arm rest, bracing members and seat frame. (b) The dimensions of various members are given in the drawing. In addition certain other details as mentioned below:- (c) Front Legs-02 :- The legs shall be made out of 3”dia and 1’6”height of varying diameter all as covered /moulded as shown on drg and as directed ny E-in-charge/GE. (d) Rear legs 02:- The rear legs shall be extended to form back rest of chair, madeout of 2 inch x 4 inch thick first class teak wood. Its height shall be 3’4” and it shall be fabricated to size and shape all as indicated in the drg . (e) Arm Rest:- The arm rest of the chair shall be fabricated by carving/ moulding as shown in drawings and it shall be attached to rear legs and front legs for support. (f) Bracing members:- These members should be provided near the bottom of the chair bracing all four legs and shall be made out of first class teak wood of dimensions all as per drawings. (g) Seat frame:- A seat frame shall be made by conjoining rear legs and front legs using first class teak wood of dimenssion3 inch x 1.5 inch. The frame should have adequate support and bracing to accommodate cushion and weight of 150kg. Contnd.... 7.01

Contnd.... 7.00 (h) Cushion:- The cushion shall be provided inside the frame of chair of 3” thickness and it shall be of 32 density covered with best quality tapestry cloth as directed by E-in-charge/GE. The cost of Tapestry cloth shall not be less than Rs. 400 per sqm. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (i) Back rest:- Back rest shall be formed using a teak wood frame and it shouls be supported by rear legs and shall have sufficient cross bracing to support the weight.The back rest assembly shall be having a cushion of 3” thickness and it shall be of 32 density covered with best quality art lather as directed by E-in-charge/GE. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (j) The carvings and mouldings shall be made as per drawing or as directed by E- in –charge/ Garrison engineer. (k) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (l) Polish:- The entire sofa set except ply board shall be polished in chestnut brown. (m) The carvings and mouldings shall be made as per drawing or as directed by Engr- in – charge/ Garrison engineer. (n) Hard rubber ring/toe shall be provided

Side Table:- Drawing No. CWE / NAG / SK /12 / 2024 Overall size of the side table shall be 1’ x 1’ and height shall be 1’6” (Overall). All the members of the side table shall be made of class-I teak wood. The specifications of side table shall be as given below:- (a) It shall have members i.e. Legs x 04, bracing members, Top frame and Glass Top. (b) The dimensions of various members are given in the drg. In addition certain other details as mentioned below:- (i) Legs x 04:- The legs shall be made of out of square section of size 3 inch x 1.5 inch and height 16.5”. (ii) Bracing Members:- These members should be provided near the bottom of the side table bracing all four legs and shall be made out of first class teak wood of dimensions 1 inch x 1 inch fit to finish as shown in the drg. (iii) Top Frame:- A top frame shall be made by conjoining all four legs using first class teak wood of dimensions 2 inch x 1 inch. The outer to outer size of the frame shall be 12” x 12” and it shall have grooves to accommodate a top glass of size 9” x 9”.The frame should have adequate support and bracing to accommodate the weight of top glass and additional expected weight on top. (iv) Top Glass:- Toughened glass of thickness 1 inches and dimensions 9” x 9” with smooth edges shall be provided at the top. (v) All the carvings and mouldings shall be made as per drg or as directed by Engr -in-charge/Garrison Engineer. (vi) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (vii) Polish:- The entire dining table shall be polished in chestnut brown. (viii) Hard rubber ring/toe shall be provided

The Table Bed Side (Type-I):- Drawing No. CWE / NAG / SK /13 / 2024 Overall size of the Table bed side shall be 2’ long, 2’6” wide and its height shall be 1’8”at the Top. The specifications of Table bed side shall be as given below:- (a) It shall have members i.e. Legs x 04, Drawers x 03, Top. (b) The dimensions of various members are given in the drg. In addition certain other details as mentioned below:- (i) Legs x 04:- The legs shall be of length 1.8 feet and dimensions 3 inch x 3 inch. There shall be certain mouldings and carvings which are as shown in the drgs. Exact location where moulding/carving is to be done is given at drgs. All the legs shall be made of class-I teak wood. (ii) Rails:- There shall be 04 rails and they will have min thickness of 1 inches and the size shall vary to accommodate the drawer as shown in the drgs. All the rails shall be made of class-I teak wood. (iii) Drawers:- The entire drawer (03 Nos) shall be made of teak wood and have min thickness of 1 inches, width of 4 inches and length of 28’’, fixed over 90mm x 90mm teak wood bearer fixed on sides. On the external face there shall be a handle/knob made of brass. The drawer should be of approved quality telescopic channel. Contnd.... 9.01

Contnd.... 9.00 (iv) The Top of the table bed side shall be of class-I teak wood of thickness 1 inches and width 2’ and length 2’6”. (v) The 3 sides of Table bed side shall also be class-I teak wood of thickness 1 inches, width and height as shown in the drgs. (vi) The carvings and mouldings shall be made as per drgs or as directed by Engr -in-charge/Garrison Engineer. (vii) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (viii) Polish:- The entire bed bench except ply board shall be polished in chestnut brown. (ix) Hard rubber ring/toe shall be provided.

The Table Bed Side (Type-II):- Drawing No. CWE / NAG / SK /17 / 2024 Overall size of the Table bed side shall be 2’ x 1’9" and its height shall be 1’8”at the Top. The specifications of Table bed side shall be as given below:- (a) It shall have members i.e. Legs x 04, Drawers x 03, Top. (b) The dimensions of various members are given in the drg. In addition certain other details as mentioned below:- (i) Legs x 04:- The legs shall be of length 1.8 feet and dimensions 3 inch x 3 inch. There shall be certain mouldings and carvings which are as shown in the drgs. Exact location where moulding/carving is to be done is given at drgs. All the legs shall be made of class-I teak wood. (ii) Rails:- There shall be 04 rails and they will have min thickness of 1 inches and the size shall vary to accommodate the drawer as shown in the drgs. All the rails shall be made of class-I teak wood. (iii) Drawers:- The entire drawer (03 Nos) shall be made of teak wood and have min thickness of 1 inches, width of 4 inches and length of 16’’, fixed over 90mm x 90mm teak wood bearer fixed on sides. On the external face there shall be a handle/knob made of brass. The drawer should be of approved quality telescopic channel. Contnd.... 10.01

Contnd.... 10.00 (iv) The Top of the table bed side shall be of class-I teak wood of thickness 1 inches and dimensions of 2’ x 1’9". (v) The 3 sides of table bed side shall also be class-I teak wood of thickness 1 inches, width and height as shown in the drgs. (vi) The carvings and mouldings shall be made as per drgs or as directed by Engr -in-charge/Garrison Engineer. (vii) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (viii) Polish:- The entire bed bench except ply board shall be polished in chestnut brown. (ix) Hard rubber ring/toe shall be provided

Wine Colour Dining Table With 06 Chair Drawing No. CWE / NAG / SK /15(a) / 2024 Overall size of the Wine colour Dining Table shall be 6' long and 3' wide and it's height shall be 2'8" at the bottom of Tabletop. Both ends of the Table shall be of oval shape as shown in the drg. All the members of the dining table shall be made of class-l teak wood. The specifications of Dining Table shall be as given below:- (a) It shall have members i.e. Legs x 02, Table Top. (b) The dimensions of various members are given in the drg. In addition certain other mentioned below:- (i) Legs x 02:- The legs shall be of height 2'8" and dimensions 1'8" x 1'8". There shall be certain mouldings and carvings which are as shown in the drg. The entire leg shall be made of a single wood piece and it should be monolithic. Exact location where moulding/carving is to be done is given at drg. (ii) The Top of the dining table shall be consisting of two detachable members. Each section shall be of dimensions 3' x 3' and thickness 2 inches. End sections of the table shall be given oval shape as shown in the drg. (iii) All the carvings and mouldings shall be made as per drg or as directed by Engr -in-charge/Garrison Engineer. (iv) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (v) The dining table shall consist of two separate detachable sections, each capable of functioning independently as shown in the drg. (vi) Polish:- The entire dining table shall be polished in chestnut brown. (vii) Hard rubber ring/toe shall be provided

Wine Colour Dining Table cum computer table Drawing No. CWE / NAG / SK /15(b) / 2024 Overall size of the Wine colour Dining Cum computer table shall be 9' long and 3' wide and it's height shall be 2'8" at the bottom of Table top. Both ends of the table shall be of overall shape as shown in the drg. All the members of the dining table shall be made of class-1 teak wood. The specifications of wine colour dining table cum computer table shall be as given below:- (a) It shall have members i.e. Legs x 01, Table Top. (b) The dimensions of various members are given in the drg. In addition certain other mentioned below:- (i) Legs x 01:- The legs shall be of height 2'8" and dimensions 1'8" x 1'8". There shall be certain mouldings and carvings which are as shown in the drg. The entire leg shall be made of a single wood piece and it should be monolithic. Exact location where moulding/carving is to be done is given at drg. (ii) The Top of the wine colour dining table cum computer table shall be consisting of three detachable members. Each section shall be of dimensions 3' x 3' and thickness 2 inches. End sections of the table shall be given oval shape as shown in the drg. (iii) All the carvings and mouldings shall be made as per drg or as directed by Engr-in-charge/Garrison Engineer. (iv) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (v) The wine colour dining table cum computer table shall consist of three separate detachable sections, each capable of functioning independently as shown in drawing. (vi) Polish:- The entire dining table shall be polished in chestnut brown. (vii) Hard rubber ring/toe shall be provided

Chair Dining Drawing No. CWE / NAG / SK /15(c) / 2024 Overall size of the chair shall be 3' high and 1'6" x 1'6". All the members of the chair shall be made of class- I teak wood. The specifications of chair shall be as given below:- (a) It shall have members l.e. Rear Legs x 02, Front legs x 02 extended to form back rest, arm rest, bracing members and seat frame. (b) The dimensions of various members are given in the drg. In addition certain other details as mentioned below:- (i) Front Legs x 02:- The legs shall be made of out of 3" dia and 1'6" height of varying diameter all as carved/moulded as shown on drg and as directed by Engr-in-charge/Garrison Engineer. ii) Rear Legs x 02 :- The rear legs shall be extended to form back rest of chair, made out of 2 inch x 4 inch thick first class teak wood. Its height shall be 3' 4" and it shall be fabricated to size and shape all as Indicated in the drg. (iii) Arm Rest :- The arm rest of the chair shall be fabricated by carving/moulding as shown in the drg and it shall be attached to rear legs and front legs for support. (iv) Bracing Members:- These members should be provided near the bottom of the chair bracing all four legs and shall be made out of first class teak wood of dimensions all as per drawings. (v) Seat Frame:- A seat frame shall be made by conjoining rear legs and front legs using first class teak wood of dimensions 3 inch x 1.5 inch. The frame should have adequate support and bracing to accommodate cushion and weight of 150kg. Contnd.... 13.01

Contnd.... 13.00 (vi) Cushion Seating:- The cushion shall be provided inside the frame of chair of 3" thickness and it shall be of 32 density covered with best quality art lather as directed by Engr-in-charge/Garrison Engr. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (vii) Back Rest:- Back rest shall be formed using a teak wood frame and it should be supported by rear legs and shall have sufficient cross bracing to support the weight. The back rest assembly shall be having a cushion of 3" thickness and it shall be of 32 density covered with best quality art lather as directed by Engr-in-charge/Garrison Engr. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (vii) The carvings and mouldings shall be made as per drawing or as directed by E- in –charge/ Garrison engineer. All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (viii) Polish. The entire bed bench except ply board shall be polished in chestnut brown (ix) Hard rubber ring/toe shall be provided.

TV Console Drawing No. CWE / NAG / SK /19 / 2024 Overall size of the console shall be 1’4" wide, 1’3” long and 2’8” high at the top. All the members of the console shall be made of class-I teak wood. The specifications of TV console shall be as given below:- (a) It shall have members i.e. Legs x 04, Top & bottom bracing members, 01 x drawers and console top. (b) The dimensions of various members are given in the drg. In addition certain other details as mentioned below:- (i) Legs x 04:- The legs shall be of height 2’8” and dimensions 3 inch x 3 inch at the top. The member tappers down to the bottom in a circular shape with certain mouldings and carvings which are as shown in the drgs. Exact location where moulding/carving is to be done is given at drgs. (ii) Top Bracing Members:- The top bracing members shall be made by joining all the four legs and should be able to accommodate to separate parallel drawers as shown in the drg. (iii) Drawers:- The entire drawer (01 Nos) shall be made of teak wood and have min thickness of 1 inches, width of 5 inches and length of 3’9’’, fixed over 90mm x 90mm teak wood bearer fixed on sides. On the external face there shall be a handle/knob made of brass. The drawer should be of approved quality telescopic channel. (iv) TV unit Console Top:- The TV unit console top shall be of class-I teak wood of thickness 1 inches and width 1’4” and length 3’7" with curved shape at one end as shown in the drg. Contnd.... 14.01

Contnd.... 14.00 (v) Bottom Bracing:- These members should be provided near the bottom of the console bracing all four legs and shall be made out of first class teak wood of dimensions 2 inch x 1 inch fit to finish. (vi) The carvings and mouldings shall be made as per drgs or as directed by Engr -in-charge/Garrison Engineer. (vii) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (viii) Polish :- The entire bed bench except ply board shall be polished in chestnut brown. (ix) Hard rubber ring/toe shall be provided

Chair Visitor. Drawing No. CWE / NAG / SK /21 / 2024 Overall size of the chair shall be 3’ high and 1’6” x 1’6”. All the members of the chair shall be made of class-I teak wood. The specifications of chair shall be as given below:- (a) It shall have members i.e. Rear Legs x 02, Front legs x 02 extended to form back rest, arm rest, bracing members and seat frame. (b) The dimensions of various members are given in the drg. In addition certain other details as mentioned below:- (i) Front Legs x 02:- The legs shall be made of out of 2” dia and 1’4” height of varying diameter all as carved/moulded as shown on drg and as directed by Engr-in-charge/Garrison Engineer. (ii) Rear Legs x 02:- The rear legs shall be extended to form back rest of chair, made out of 2 inch x 6 inch thick first class teak wood. Its height shall be 3’ and it shall be fabricated to size and shape all as indicated in the drg. (iii) Arm Rest :- The arm rest of the chair shall be fabricated by carving/moulding as shown in the drg and it shall be attached to rear legs and front legs for support. (iv) Bracing Members:- These members should be provided near the bottom of the chair bracing all four legs and shall be made out of first class teak wood of dimensions 1 inch x 2 inch fit to finish. (v) Seat Frame:- A seat frame shall be made by conjoining rear legs and front legs using first class teak wood of dimensions 1.5 inch x 3 inch. The frame should have adequate support and bracing to accommodate cushion and weight of 150kg. Contnd.... 15.01

Contnd.... 15.00 (vi) Cushion Seating:- The cushion shall be provided inside the frame of chair of 3” thickness and it shall be of 32 density covered with best quality art lather as directed by Engr-in-charge/Garrison Engr. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (vii) Back Rest:- Back rest shall be formed using a teak wood frame and it should be supported by rear legs and shall have sufficient cross bracing to support the weight. The back rest assembly shall be having a cushion of 3” thickness and it shall be of 32 density covered with best quality art lather as directed by Engr-in-charge/Garrison Engr. The cushion assembly shall be machine stitched and the entire assembly shall be fit to finish and neat. (viii) All the carvings and mouldings shall be made as per drg or as directed by Engr -in-charge/Garrison Engineer. (ix) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (x) Polish:- The entire dining table shall be polished in chestnut brown. (xi) Hard rubber ring/toe shall be provided

Table Executive Drawing No. CWE / NAG / SK /22 / 2024 Overall size of table executive shall be 4' wide, 1'3" long and 2'8" high at the top. All the members of the console shall be made of class-I teak wood. The specifications of Table executive shall be as given below:- (a) It shall have members i.e. Legs x 04, Top & bottom bracing members, 01 x drawers and table top. (b) The dimensions of various members are given in the drg. In addition certain other mentioned below:- (i) Legs x 04:- The legs shall be of height 2'8" and dimensions 3 inch x 3 inch at the top. The member tappers down to the bottom in a circular shape with certain mouldings and carvings which are as shown in the drgs. Exact location where moulding/carving is to be done is given at drgs. (ii) Top Bracing Members:- The top bracing members shall be made by joining all the four legs and should be able to accommodate to separate parallel drawers as shown in the drg. (iii) Drawers:- The entire drawer (01 Nos) shall be made of teak wood and have min thickness of 1 inches, width of 5 inches and length of 3'9", fixed over 90mm x 90mm teak wood bearer fixed on sides. On the external face there shall be a handle/knob made of brass. The drawer should be of approved quality telescopic channel. Contnd.... 16.01

Contnd.... 16.00 (iv) Table Executive:- The table executive top shall be of class-I teak wood of thickness 1 inches and width 1'3" and length 4' with curved shape at one end as shown in the drg. (v) Bottom Bracing :- These members should be provided near the bottom of the table executive bracing all four legs and shall be made out of first class teak wood of dimensions 2 inch x 1 inch fit to finish. (vi) The carvings and mouldings shall be made as per drgs or as directed by Engr -in-charge/Garrison Engineer. (vii) All the joints shall be keyed by tongue and groove joint method and the same shall not be visible on the external side of the assembly. (viii) Polish:- The entire bed bench except ply board shall be polished in chestnut brown. (ix) Hard rubber ring/toe shall be provided.

Bath Stool PVC FD/E6/MAP/07

Recepticle PVC 20 Ltr capacity FD/E6/MAP/13

Side board Multipurpose FD-372

Table centre FD/MAP/08

Mirror dressing Gents FD/E6/MAP/16

Table Writing FD-275

Shoe rack (size 600mm x 400mm x 1027mm) FD/E6/MAP/02 (R)

Chair tubular steel with arms (FD-75M/386)

Charpoy with Hard top (FD/MAP-II/01)

Form without back steel (FD-1027)

Table 3'x2' (900x600x760) without drawer (FD-284/231/41M)

Bin linen multi purpose with ironing board (FD/E6/MAP/09)

Chair easy (FD-229)

Chair Varandah Officer (FD/MAP-II/06)

Charpoy folding IP with hard top FD-388(R)

Hat stand with mirror large FD-362

Ladder Aluminium FD-1025

Teapoy FD-278

Teapoy varandah FD/E6/MAP/17

Rifle rack TP (Make: Kaypee, Model: 10 AB ( 5.56 INSAS)

Chair computer medium back TP (Model: GA 538A, Make: Geeken)

Chair Visitor Type-I TP (Model: GB 403, Make: Geeken)

Chair revolving high back TP (Model: GA 568 Synchro Knee Tilt, Make: Geeken)

Budget Furniture Industries (BID ID -3255205)

Bidder Name

dhanshree enterprises

Budget Furniture Industries