PROVN OF BOUNDARY WALL WITH ENTRANCE GATE AT DCN NODE UNDER GE (SOUTH) UDHAMPUR

Amount

Excavation over areas not exc 1.5 M deep and getting out in any type of soil complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, etc. n exc 10 sq m on plan and n exc 1.5 m in depth in any type of soil and getting out soil, complete all as specified and as directed by Engr-in-Charge.

Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete all as specified.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil, complete all as specified and as directed by Engr-in-Charge.

Removing excavated material exc. 250m and not exceeding 500 mtrs and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and as directed by Engr-in-Charge.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, to obtain rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions etc, square, ractangular or polygonal, to obtain rough finished flat surface of concrete complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams,beam haunchings,girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams, etc. complete all as specified and as directed.

RCC M-25 (design mix), using 20 mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beam; plinth beams; bases of columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed by Engr-in-Charge.

RCC M-25 (design mix), using 20 mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts, complete all as specified and as directed by Engr-in-Charge.

RCC M-25 (design mix), using 20 mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and as directed by Engr-in-Charge.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engr-in-Charge.

TMT mild steel bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engr-in-Charge.

15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4, finish surfaces fair and even without using extra cement, complete all as specified and as directed by Engr-in-Charge.

10mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Preparing newly plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of suitable primer, complete all as specified and as directed by Engr-in-Charge.

PVC pipe 110mm bore single socket in any length as in weep holes of retaining wall all as specified and as directed by Engr-in-Charge.

Providing precast cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) louvres and jallies, 50mm thick (measured solid) , including all mouldings but excluding frame Set in cement mortar 1:4, complete all as specified.

Mild Steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, conforming to Fe-290 Gde-E-165, complete all as specified and as directed by Engr-in-Charge.

Preparation of new steel surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over and including a coat of red oxide chrome primer, complete all as specified and as directed by Engr-in-Charge.

Glazed ceramic coloured tiles of size 450mm x 300mm x 7 mm thick on vertical surfaces of walls as in dado/skirting etc., set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick screed bedding/ backing layer in CM 1:4, complete all as specified and as directed by Engr-in-Charge.

Providing cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles including necessary formwork complete all as directed and specified.

devraj chalotra