CONSTRUCTION OF INSPECTION SHED AT SUPPLY DEPOT ASC WELLINGTON AND CERTAIN REVENUE WORK AT WELLINGTON AREA UNDER GE WELLINGTON

Amount

Removal of bushes, shurbs and vegetation by surface dressing not exceeding 15 cm deep in any type of soil all as specified and directed.

Excavation in trenches not exceeding 1.5 meter deep and not exceeding 1.5 meter wide and gettting out in Soft/ Loose soil for laying of under ground cable, and foundation of poles, etc complete all as specified and as directed.

Excavating in post holes (or similar holes) each in soft /loose soil not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering and removal of excavated materials to a distance not exceeding 50mtr and making good surfaces, complete all as specified and directed

Plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concreting, complete all as specified and directed.

Steel work in square/rectangualr tubular trusses/vertical members/purlins etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 etc con- forming to Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication all as specified and directed.

Preparation of new or untreated steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet as in ridge of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed.

Use and waste of timber as in formwork to sides of concrete foundations, footings, base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work; vertical or to batter flat surface rough finished complete all as specified and directed.

Reinforced cement concrete (nominal mix) Type B1, 1:2:4 using 20 mm graded stone aggregate as in foundations, including rafts, footing, foundations, beams, plinth beams, bases for columns, etc., basement slabs, under reamed piles and mass concrete etc complete all as specified and directed.

Use and waste of steel Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. Fair finished surfaces of concrete flat complete all as speicified and directed.

Reinforced cement concrete (nominal mix) Type B1, 1:2:4, using 20mm graded stone aggregate for beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use and waste of formwork for fair finished surface of chajjas, trough, fin and similar items including edges all as specified and directed.

Reinforced cement concrete (nominal mix) Type B1, 1:2:4, using 20mm graded stone aggregate for chajja, fin complete all as specified and directed.

Pre-cast cement concrete block masnory with solid block exceeding 10cm in width and setting in mortar 1:6 type C1 1:3:6 using 20mm graded aggregate complete all as specified and directed

Pre-cast cement concrete block masnory with solid block not exceeding 10cm in width and setting in mortar 1:6 type C1 1:3:6 using 20mm graded aggregate complete (with plain or interlocking joints as directed) setting in motar, complete walls built all as specified and directed

Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm (5mm thick in cement mortar 1.4 with WPC over a coat of 10mm thick in cement mortar 1:6) on other than fair faces of brick work or concrete surface including finished even and smooth with using extra cement all as specified and directed.

Mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No 19 hereinbefore but 5mm dia and over upto and including 10 mm dia in stirrups, spacers and binders all as specified and directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base to floor 100mm thick all as specified and directed.

100 mm thick Plain cement conncrete 1:2:4, type B-1 using 12.5mm graded crushed stone aggregates as in floor surface all as specified and directed.

Applying three coats of white wash over a coat of primer over one coat of 3mm thick wall care putty on newly plastered wall surface including preparation all as specified and directed.

Applying two coats of cement base paint over a coat of primer on newly plastered surfaces of wall including preparation of surfaces all as specified and directed.

Hardcore of broken stone gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed.

75mm thick plain Cement concrete , 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection all as specified and directed.

Forming 12mm thick Expansion joints filled with Pre-formed bitumious filler and top 30mm primed and sealed with sealing compound Grade 'A' all as specified and directed.

Removing excavated soil/ material to a distance exceeeding 250m and not exceeding 500m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Steel rolling shutter with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete push pull or manual type thickness of laths in 125mm all as specified and directed.

Ball bearing for rolling shutters complete all as specified and directed.

Mild steel Framed work such as grill, grating etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron door, ladders, framed balusters and simialr work conforming to Fe290 Gde E-165 all as specified and directed.

Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

Moorun/ red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

Expanded metal, not exc 4.00 kg cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members all as specified and directed.

Aluminium dividing strips, 1.5mm thick and 38mm width inserted in position, conform to design all as specified and directed.

100mm thick Plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floors/ pavings etc all as specified and directed.

Chequered cement concrete coloured tiles 30 cm x 30 cm x 25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors, steps etc over and including 15 mm thick screed bed in CM 1 :6 complete all as specified and as directed.

130mm thick PCC 1:2:4, type B1 using 20mm graded stone aggregate as in floors/ pavings ets complete all as specified and directed.

PCC 1:2:4 20mm graded aggregate in wall or retaining walls, any thickness, size or shape including pilaters, buttresses coloumns, pillars, boundary pillars and posts including necessary form work all as specified and directed.

Pre-Fab Portable Toilet Indian Type (IWC) cabin (Material LLDPE) size (L 1000mm x W 1100mm x H 2325mm) including one water tap (PVC fittings Pipe/ Polo), inner wash basin with water tap and 1 bulb holder and switch including all civil work for platform etc including door shutter all as specified and directed. Make: Sintex or Equivalent as approved by GE.

Pre-Fab Portable Bathroom Type Cabin (Material LLDPE) Size (L 1000mm x W1100mm x H 2325mm) PVC door size 1850mm H x 615mm W x 25mm T (PVC Fittings Pipe/ Polo), including Water tap and 1 bulb holder and switch, PVC Towellrod, PVC Soap dish including civil work for platform etc all as specified and directed.

PVC Water Tank including all connections, float valve with mild steel staging 3.00 mtr height for fixing 1000 ltr capacity water storage PVC with painting 1000 Lts all as specified and directed.

PVC septic tank 1500 Ltr with 40to 60 Flush (15 to 20 users) (W-1025, L-2350 mm, H-1250mm) with all civil work such as excavation, RFR and including PVC pipe connection upto 3m diatance haunching with PCC etc all as specified and directed.

PVC Soak Pit 50 Ltr with all civil work such as excavation, RFR and including PVC pipe connection all as specified and directed.

Earth work in excavation in any kind of soil by mechanical means (Hydraulic excavator) over areas (exceeding 30cm and not exceeding 1.5m in depth not exceeding 1.5m in width as) including getting out and disposal of excavated earth led upto 50m and lift upto 1.5m all as specified and directed.

Earth work in excavation in any kind of soil by mechanical means (Hydraulic excavator) over areas (exceeding 30cm and exceeding 1.5m in depth not exceeding 1.5m in width as) including getting out and disposal of excavated earth led upto 50m and lift upto 1.5m all as specified and directed.

Rendering 10mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces with using water proofing compound all as specified and directed. Note: Water proofing compound can be measured separately.

Rendering 15mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces with using water proofing compound all as specified and directed. Note: Water proofing compound can be measured separately.

Supply only integral water proofing compound all as specified and directed.

Returning filling in including spreading, levelling watering and well ramming in layer not exceeding 25 Cms all as specified and directed.

PCC 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, plinth courses, etc and similar work including necessary form work complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surface of concrete complete all as specified and directed.

Reinforced cement concrete (nominal mix) Type B1, 1:2:4, using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts all as specified and directed.

Use and waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) rough finished surfaces complete all as specified and directed

Reinforced cement concrete (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Mild steel TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers, binders, etc complete all as specified and directed.

Plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in 50mm thick flooring and finishing the surfaces fair and even without using extra cement all as specified and directed.

Coloured Non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Coloured Glazed ceramic tiles in vertical surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in cement mortar 1:3 complete, complete all as specified and directed.

PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and as directed

Factory made solid panel PVC door shutter 30mm (Stile) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, fixed including welding complete all as specified and directed (Box type frame and shutters).

4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 sq. m in each pane all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section 150 mm long all as specified and directed.

Aluminium butt hinges 100mm size all as specified and directed.

Aluminium handles, cast type, anodised 100 mm long, complete all as specified and directed.

Vitreous china squatting pan, Orissa pattern of size 580 x 440mm (white coloured) with integral foot rests (excluding flushing cistern and flush pipe) with P or S trap portion to match with existing surface of floor all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white (excluding flushing cistern) plastic water closet seat cover and mild steel chromium plates or aluminised hinging device, trap and connection to drain and flush pipe complete all as specified and directed.

Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Vitreous china half stall bowl urinal flat back, size of 465 x 355 x 265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and directed.

Urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weigth 60gms) all as specified and directed.

15mm bore concussive push button taps of cast iron alloy, screwed for iron pipe and fixed all as specified and directed.

Vitreous china wash basin, white ovel shape counter wash basin size 560x400x205mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of taps, fixing of supply and waste pipe complete all as specified and directed.

PVC waste pipe of 32/40mm bore suitable for wash hand basin/ sink complete all as specified and directed.

32mm waste coupling of PTMT (Half or full threaded) (minimum weight 32mm-45gms) all as specified and directed.

Pillar taps, 15mm bore, fancy type ,cast copper alloy with capstan heads, chromium plated, screwed down high pressure, screwed for iron pipe and fixed all as specified and directed.

PVC connections 15 mm size with PTMT nuts of length 750mm all as specified and directed.

Bib taps,15 mm, fancy type,cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type chromium plated ,15mm bore all as specified and directed.

Soap dish, chromium plated 100x100x60mm fixed to wall with plugs with chromium plated screw complete all as specified and directed.

Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges including all as specified and directed.

PVC (SWR) floor trap plain with grating and jointing with solvent cement all as specified and as directed.

PVC (SWR) bend of any radius 75 mm dia complete all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia complete all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia with access door complete all as specified and as directed.

PVC (SWR) junction single, (single T) equal or unequal of 75mm bore of pipe complete all as specified and directed.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, fixed to walls with necessary clamp all as specified and directed.

PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

Hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed.

Rotational moulded polyethylene water storage tank of capacity 1000 Ltr (cylindrical vertical with closed top) three layers hoisted and fixed in position with proper inlet and outlet connections all as specified and as directed

GI tubes 15mm bore medium grade with all fittings and laid in floor/ wall/ ceiling etc complete all as specified and directed.

GI tubes 20mm bore medium grade with all fittings and laid in floor/ wall/ ceiling etc complete all as specified and directed.

Ball brass valves high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed of dia 20mm all as specified and directed.

Damp proof course 40mm thick in cement concrete 1:2:4, type B1 using 20mm graded stone aggregate to horizontal or vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen at the rate of 1.50 Kg per square meter and blinding with clean dry sand @ 0.05 cu.m per sqm over polythene film 50 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 Kg/Sqm all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified and directed.

Chequered cement concrete coloured tiles 30 cm x 30 cm x 20-22 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors, steps etc complete all as specified and as directed.

Chequered cement concrete coloured tiles 30 cm x 30 cm x 20-22 mm thick, with grey cement and pigments, for work on vertical surfaces as in skirting, dados and risers of steps set, jointed and pointed in neat cement slurry in floors, over and including rendering 10 mm thick screed bed in CM 1 :4 complete all as specified and as directed.

APP based polymeric membrane minimum weighing 4.5 kg/ Sqm and minimum 4mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms / Sqm) land on primed surface by forced application and finished with solar reflective bitumenous aluminium paint / primer @ 0.1Kg/sqm all as spcified and directed.

18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars window cills, cooking, wash basin platforms/ partition and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigmet to match with shade of granite all as specified and directed.

Rounding edges of stone slabs one edge such as steps, cooking platforms and other similar situation, complete all as specified and directed.

Rendering 5mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 in ceiling finished even and smooth without using extra cement complete as specified and directed

Preparing surfaces, plastered or unplastered on new ceiling surface and applying three coats of white wash complete all as specified and directed.

Point wiring complete with 1.5 sqmm (nominal area) FRLS grade PVC insulated, unsheathed stranded copper conductor single core cable 1100 volts grade in and including PVC conduit medium grade complete with conduit fittings/accessories with provn of 1.2 mm thick MS/PVC terminal boxes of suitable size and 3 mm thick plastic laminated sheet top cover for housing of switches, sockets etc including 1.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor and connected to common earth dolly for One light/ fan point controlled by one switch 5Amps SP size all as specified and directed.

All as per Item No 109 hereinbefore but One 3 pin 5Amps Socket outlet on same board control with other switch complete all as specified and directed

All as per Item No 109 hereinbefore but point wiring complete with 4 sqmm FRLS cable for 3 pin 15 A socket outlet on independent board including 4 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor all as specified and directed.

Modular switch one way 6A 230V AC 50 HZ SP one module all as specified and directed.

Modular switch one way 16A 230V AC 50 HZ SP one module all as specified and directed.

Modular socket 2/3 pin combined 6A 230V AC 50 HZ SP two module all as specified and directed.

Modular socket 6A/16A 2/3 pin combined 230V AC 50 HZ SP two module all as specified and directed.

Modular White Cover Plate with frame, 3 module all as specified and directed. Make: Havells/ Legrand/ L&T.

Modular White Cover Plate with frame, 8 module all as specified and directed. Make: Havells/ Legrand/ L&T.

Ceiling rose, 3 terminals PVC / polycarbonate, isolated body including base block all as specified and directed.

Wall mounted 20W LED batten comprising of thermally conductive material, pre-wired with high efficiency electronic driver, high translucent frosted diffuser, lamp color white complete all as specified and directed.

Exhaust fans of metal body AC single phase 230/ 240V of size 300mm sweep with louver all as specified and directed.

Distribution board sheet steel phosphatised powder coated for MCB/ DB with copper bus bar and neutral link earthing stud (confirming to IS-13032, IS-8623) SPN 8 way 240 Volts double door all as specified and directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amps, in the MCB DB Complete with connection testing and commissioning all as specified and directed. Make: ABB/ Legrand/ L&T.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles Neutral and current carrying capacity 32 Amps, in the MCB DB Complete with connection testing and commissioning all as specified and directed. Make: ABB/ Legrand/ L&T.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the platee not less than 1.5 mtr below normal ground level, connected to galvanized earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical platee No 3 connected to earth testing point including necessary excavation, earth work, PCC pit ,RCC cover 1:2:4 B1 with 8 mm dia MS bars at 100 c/c, funnel, watering pipe etc. all as specified and directed including testing on completion.

LED building security light fitting of 35 Watt including necessary accessories and GI bracket of suitable size complete all as specified and directed. Make: Crompton Cat No LSTS-20-CDL-M or equivalent in Havells/ Bajaj etc.

XLPE insulated screened PVC bedded, galvanised Steel Strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor, laid in trenches/ ducts, fixed on wall/ inside panel, drawn through pipe of size 2Core x 10Sqmm complete including taking out the old unserviceable LT cable all as specified and directed.

Supply and spreading clean dry riddled sand in trenches for cushioning all as specified for cable protection in trenches / ducts complete all as specified and directed. Note: The punned down thickness shall only be measured

Supplying and laying reinforced precast concrete cable cover,Class LV, Type I, flat, size 250mm x 150mm x 40mm all as specified and directed.

Frame plate six module including matching plate all as specified and directed.

Light fitting mirror type with high out put diffuser 2 feet, 10watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Distribution board sheet steel phosphatised powder coated for MCB/DB with copper bus bar and neutral link earthing stud (confirming to IS-13032, IS-8623) 4 way with 200amps rated bus bar single door 240Volt all as specified and directed.

MCB SP 06 to 32Amps, 240 Volts, 50HZ AC supply complete all as specified and directed.

MCB SPN 40Amps, 240 Volts, 50HZ AC supply complete all as specified and directed.

Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, copper winding of Sweep 250mm all as specified and directed.

P K ENTERPRISES

m/s prabakaran