SPL REPAIR TO BLDG NO P-267 (PERS COOK HOUSE) AT 422 FD HOSP UNDER GE (WEST) DELHI CANTT-10 AND PROVN OF TOILET CUMBATHROOM NEAR BLDG NO P-25 AT 1/5 GR UNDER GE (WEST), DELHI CANTT-10

Amount

Surface excavation n exc 30cm deep and averaging 15cm deep including getting out in any type of soil

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Filling under floor, spreading and levelling in layers n exc 25cm thick well raming including watering as requred complete all as specified and directed

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface under sub base flooring or plinth protection etc.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete

M&L for RCC M25 design mix, using 20mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete

M&l for RCC M25 design mix, using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts

M&L for RCC M25 design mix using 20mm graded stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L for RCC M25 design mix using 20mm graded stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for RCC M25 design mix using 20mm graded stone aggregate in Chajjas

Use and waste for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

Use and waste for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.for rough finish surface

Use and waste for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finish surface

Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and opening,

Use and waste for Formwork to chullah hoods, chajjas, troughs and similar items including edges

Use and waste Formwork to sides of pillars,posts, struts, piers, columns and stanchions

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Ditto as above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base flooring

M&L for 75mm thick PCC 1:3:6 type C-2 (40mm graded agg) for plinth protection laid in bays and finished even and fair incl filling the joint with bitumen mastic complete all as specified and directed .

M&L for PCC 1:3:6 type C-2 (20 mm graded agg) as in surface channel/drain / haunching of manhole etc.

M&L for Glazed ceramic tiles in vertical surface 300x450x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick screed bedding/backing in CM 1:4

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thic screed bedding layer in CM 1:6

M&L for vitreous china wash hand basin flat back size 550x400 mm size white excluding taps waste chain and plug and porcelain stopper but including brackets and 32mm dia waste fittings brass chromium plated with long screwd shanks and fly nuts, 32x600mm long PVC waste pipe complete

M&L for Ready Mix plaster 15mm thick on brick or concrete surface of internal and external walls finished even and fair surface without using extra cement complete all as specified and as directed.

M&L for 15mm thick cement plaster on brick or concrete surface in CM 1:6 finished even and fair surface without using extra cement

M&L for Ready Mix plaster 5mm thick on concrete surface of ceiling finished even and fair surface without using extra cement complete all as specified and as directed.

M&L for brick work in cement morta 1:6 using sub class B bricks, straight or curved on plan exc 6mtr mean radius complete all as specified and directed.

M&L for 40mm thick DPC on horizontal or vertical surface in PCC 1:2:4 type B0 using 12.5mm graded stone aggregate including necessary formwork and using WPC as per Manufacturer insruction

Preparation of newly plastered surface on wall and applying two coats of cement based paint over one coat of primer white or tinted complete

Ditto but three coats of white lime wash or tinted complete

Ditto but three coats of white lime wash on ceiling complete

M&L for water proofing treatment to roof surface with APP water proofing membrane 3mm thick & weighing not less than 3.0 kg/sqm of approved make black finish & reinforced with non woven polyester matt of min 150 gm/sqm laid over a coat of bitumen primer conforming to IS-3384 @ 0.4 Ltr/sqm over prepared roof surfaces, forcing overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100mm at ends & sealing as per manufacturer's instructions complete all as spd and directed. Note :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only. 2. Bitumen primer, bitumen and membrane shall be of same make/manufacturer. 3. The APP Membrane to be inserted in the parapet wall/wall by cutting chases of atleast 65X50mm size & making good in CM 1:3. complete all as specified and directed.

M&L for rendering 10mm thick cement mortar 1:4 on fair face of brick work or concrete surface on wall/roof surface including using WPC as per manufacturer instruction

M&L for sand bedding/cushioning under interlocking tiles floor complete.

M&L Machine pressed precast concrete interlocking glossy paver block any sahpe and size confirming to IS15658-2006 of 60mm thickness, M-35 grade set and jointed with white cement and pigment

S&F pre cast concrete block for kerb stoen with solid block ex 10cm in width type C1, 1:3:6 (using 20mm graded stone aggregate ) set in CM 1:6 of any shape and size. Kerb stone shall be fixed in true line and level or incurves for edging of road side path including embedding in ground to any depth as reqd.

M&L for PCC 1:3:6 type C-2 ,bed concrete to 150mm bore dia drain pipes (of 100mm thick) including packing under, and haunching against the sides of pipes after they are laid and tested;

M&L for 150mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed as specified

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coping, bed plates, kerbs including weathering slightly rounded or chamfered and throating complete

M&L for 75mm thick SFRC manhole/drain cover size not exc 1.00sqm each set and jonted in cement mortar 1:4 complete.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete.

S&F 150 mm long aluminium anodised barrel tower bolt extruded section.

S&F 150mm long extruded aluminium alloy handle

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete

S&F 4mm thick pin headed, figured glass with oil putty in square n exc 0.50 sq m in each pane

M&L for preparation of new steel surface and applying two coat of synthetic enamel paint over one coat of red oxide primer

S&F for 15mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed

S&F for 20mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed

S&F for 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified.

S&F 20mm float ball valve high pressure of PTMT with epoxy coted aluminium rod & high density plastic bal serewed for ison pipe

S&F brass body chromium plated fancy type health faucet with chromium plated 1mtr long pipe complete

S&F vitreous china white european type WC with "P" or "S" trap including connection to drain pipes, traps and PVC flushing cistern with pipe 32mm dia PVC flush pipe including PVC seat cover and fixing bolts complete all as specified and directed.

S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed.

S&F 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

M&L for Bib tap fancy type, chromium plated for 15mm bore of pipe, cast copper alloy with crutch or butter fly handle, screwed for iron pipe complete

M&L for stop vale/angle vave cast copper alloy chroumium plated fancy type for 15mm bore dia of pipe

S&F 15mm bore dia pillar tape cast copper alloy chromium plated fancy type screwed down for high pressure pipe

S &F brass CP shower rose of size 125 mm with swivel joints fixing to steel pipes etc. all as specified.

S&F 15mm nominal internal bore PVC connection 450mm long with two brass nuts and PVC washers

S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F vitreous china full stall urinals,white, complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, grating and union for discharge pipe all as specified and as directed.

M&L for 75mm out let diaPVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F 75mm PVC (SWR) pipes single socket in any length with rubber ring joints, fixed to wall or laid in trenches

S&F in 75mm bore PVC (SWR) bends any radius all as specified and direction

S&F in 75mm bore PVC (SWR) bends with acess door any radius all as specified and direction

M&L for 110mm bore PVC (SWR) pipe conforming to relevant IS single socketed in any length with rubber ring joint and fixed to wall complete incl taking down old rain water pipes

S&F 110mm bore PVC (SWR) bends any radius all as specified and direction

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal with acess door any radius all as specified and direction

S&F 110mm bore PVC (SWR) vent cpwl any radius all as specified and direction

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each complete all as spd & directed.

All as per item No. 78 above but n. exc 1.5 sq. m each.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as spd & directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Dismantling Brick tiles or terracing tiles, single layer on roofs including thatching any type, mud phuska etc including cleaning the surface by water/air pressure and removal of debrish beyond MOD land complete all as specified and directed.

Dismantling framed timber scantlings any size in section, in any position (as in purlins etc) complete all as spd & directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings incl ridge complete all as spd & directed.

Complete removal of existing treatment of painting by scraping, brusing, wahing down to open the brick or concrete original surface and raking out joints/ pointing in cement mortar to brick work in walls or to bricks on edge in floors, surface channels, roofs, etc complete all as spd & directed.

M&L for powder coated Anodised aluminium frame for doors, windows, ventilators, grill, partitions, sliding tracks, aluminium section for shutters suitable for two/three/four track window and aluminium section sliding members incl all necessary fittings and fixtures, jointing cleats, rubber packing etc complete all as specified and directed.

S&F powder coated aluminium window and ventilator shutters, side hung type with/ without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2 Nos) suitable handle (1 No) complete all as specified and directed.

M&L for powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,(handles 2 Nos in each door, 15mm aluminium hinges-3 Nos each door, 15mm Aluminium tower bolt 02 Nos each door), anodised aluminum snap beading screws etc. complete all as specified.

S&F Factory made 35mm thick second class hard wood plain framed panelled door shutters (Minimum two panels) with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The sizes of rail and stiles as per IS:1003 ( Part I), kiln seasoned and chemically pressure treated and fixed in position complete all as spd & directed .

S&F factory made 35mm thick 2nd class hard wood glazed / gauged shutters, open, rebated prepared to receive glass , guage etc W/O sash bars for doors as specified in SSR Part I complete all as spd & directed .

S&F for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors/door frames; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as spd and directed.

S&F MS butt hinges medium weight 100 mm size fixed with MS screws.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.50mm graded stone aggregate as in levelling couse of sub base all as specified and directed.

S&F Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as spd & directed.

M&L for 20mm thick, granite (of any type) work (table rubbed and polished) in window-cills, cooking platforms and like in 15mm tihck cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as directed.

M&L for machine cut kota stone slab 20-25mm thick as in riser of stpes, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing surface and including 15 mm thick screed bedding layer in CM 1:6 complete all as spd & directed.

M&L for providing not exceeding 1mm thick wall care putty on wall surface complete all as spd & directed.

M&L for Rough cast plaster, applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone of size between 6 to 12 mm mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete all as specified and directed.

M&L for preparation of old treated brick surfaces of walls upto by scrubbing with wire brush, hard brush, washing down with water and applying two coats of cement paint, white or tinted over one coat of alkali resistant primer complete all as spd & directed.

M&L preparation old plastered surfaces of ceiling and applying two coats of white wash all as specified and directed.

M&L for Preparation of new rough cast plastered surfaces of wall and applying two coats of cement based paint white or tinted ,complete all as specified and directed .

M & L preparation of new surfaces plastered of wall two coats of distempering walls with distemper oil emulsion, white or tinted over a coat of primer complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls and applying two coats of cement based paint white or tinted ,complete all as specified.

M&L for preparing surface of wall and applying two coat of oil bound distemper all as specified and directed.

M&L for brushing neat cement slurry with 3.Kg of cement per sqm complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in roof padding/kerb, mud slopes, rounded or chamfered edge complete all as specified and directed

M&L for providing PMM (Polymer modified cementitious mortar ) :-(i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes) (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note: Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed

Demolition and breaking of 150 mm dia sewage/drain pipe (salt glazed where AC or reinforced concrete) set in cement mortar complete all as specified & directed.

M&L for PCC 1:3:6 type C-2 ,bed concrete to 150mm bore dia drain pipes (of 100mm thick) including packing under, and haunching against the sides of pipes after they are laid and tested;

M&L for 150mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed as specified

Taking up or down 15mm bore dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm bore dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

M&L 20mm CPVC pipes SDR 11 with all plain CPVC SDR 11 and brass elbow, Tee, MTA/BTA Adeptor,tank adeptor etc. CPVC fittings and fixed complete to walls, ceiling or laid in floor complete all as spd and directed.

M&L 25mm CPVC pipes SDR 11 with all plain CPVC SDR 11 and brass elbow, Tee, MTA/BTA Adeptor,tank adeptor etc. CPVC fittings and fixed complete to walls, ceiling or laid in floor complete all as spd and directed.

S&F in repair Chromium plated brass long body bib tap fancy type 15 mm bore dia complete all as specified and directed.

S&F in repair 15mm bore angle valves, fancy type, cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle, complete all as specified and directed.

S&F Grating doom 100mm dia of SS (Minimum weight 25gms) complete all as specified and directed.

S&F Grating doom 125 mm dia with waste hole of SS. (Minimum weight 40gms) complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts complete length 600mm complete all as specified and directed.

S&F in repair flexible PVC waste pipe with coupler complete 900mm length complete all as specified and directed.

S&F in repair chromium plated stanless steel curtain rod 25mm bore fixed with fixing brackets,stops, rollers etc complete all as specified and directed.

S&F for drapery rod's side bulb stainless steel chromium plated suitable for 25mm bore curtain rod complete all as specified and directed.

S&F in repair coated MS drapery rod's brackets as required complete all as specified and directed complete all as specified and directed.

S & F of box type steel window with side hung shutters including box type hinges with steel handle, hold fast and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

Ditto as per item above but without glazing bars complete all as specified.

M&L for mild steel work with square/rectangular section in post, Roof trusses (framed), trussed, purlins, rafter, crane gantries, wind ties, rails and fastenings and heavy bracket, framing of tube sections including distance pieces, cleats, MS plates, nut & bolts etc complete all as specified and as directed.

S&F of Pre-painted galvalume aluminium zinc coating (150 GSM) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and as directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying two coats of syntethic enamel paint over one coat of red oxide Zink chrome complete all as spd & directed.

M&L for RCC 1:2:4 nominal mix using 20mm graded stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

S & F stack clamp made of 50 mm X 5 mm flat iron and 16 mm dia round iron stay including nut bolts and securing ends of stay to wall or roof suitable for 110 mm bore pipe complete all as specified and directed.

M & L in repairs for Gun-metal, globe or gate valves, with iron wheel head, screwd both end sor iron pipe and fixed 20 mm dia complete all as specified and directed.

S&F sink made of stainless steel 1mm thick for kitchen with plugs, washers and waste including bedding in cement mortar to dwarf wall or uncluding fixing cantilever breckets and connecting union to pipe over all size 495 x 420 mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base flooring complete all as specified and as directed.

S&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/window or other frames/chowkats of size 45x70mm comprising of vergin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/ wheet husk) and non toxic additive etc all as per SSR 2020 part 2 ser No 08100A. complete all as specified and directed.

S&F Factory made single extruded WPC (W) solid decorative type flush door shutter of size 30mm thick comprising of vergin polymer of K value 58-60 (Suspension grade ), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additive etc all as per SSR 2020 part 2 ser No 08105C. complete all as specified and directed.

S&F in repair vitreous China wash down water closet pan (pedestal pattern) incl P or S Trap of cast iron , white and connection with cistern complete all as specified and directed.

S&F in repair Vitreous China urinals, Half stall type (back or corner wall type), white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing brackets, flush pipe, grating and Union for discharge pipe and waste pipe complete all as spd & directed by Engr-in-Charge.

S&F plastic water closet seat cover, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device of approved colour and as per existing model complete all as specified and directed.

S & F in repairs for 15 mm bore brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified.

S&F CP wall mixer non telephonic type for mixing hot and cold water for shower screwed down for 15 mm brass iron pipe of ferrule of complete all as specified.

M&L for solid WPC (Wood Polimer Composite) sheet 18mm thick (water proof and termite proof) prelaminated one side with decorative choice colour and other side balancing white as in cup board shutter. The sheet shall be finished all edges with 0.5mm beading/ lipping of same lamination pvc sheet pasting or bonding tape etc complete all as per manufacture's instruction, specification and as directed.

S&F in repair 40 mm wide Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F for 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished same as existing model for almirah and cup board .

Material and labour for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in new modular metal flush box and providing modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit all as specified and directed by Engr-in-charge for the following :-

(a) One light/fan/bell point controlled by one way switch 5 amps.

(b) One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in PVC conduit with cable 2.5 Sqmm size 1100 volts grade conforming to IS:694 in new modular metal flush box with new modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for One 3 Pin socket 16A Indepentent board.

S&F Modular switch 1 way 6 A, 1 module complete all as specified and directed.

S&F of Modular socket outlet 6 A, 2/3 pin, combined 2 module complete all as specified and directed.

Supplying and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10.00 sqmm , complete including connection all as specified and directed.

S&F of Hot water storage(Geyser)25 Ltrs capacity, BEE 5 star rated,vertical type with suitable size of fastner and incl provision and connecting up of ss braided pipe with adopter for inlet and outlet water connection, copper element corrosion resistance antiscaling magnesium anode, having adjustable knob for temperature control and of superior glass lined inner tank and outer body material ABS with high pressure withstanding capacity upto 8 bar, having heating element 2 KW and minimum two year warranty on product, minimum 3 years warranty on heating element complete all as specified and directed.

S&F of factory made epoxy polyester powder coated distribution board SP & N 4 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 including taking down old MCB's complete all as specified and directed.

S&F of SPN MCB 40 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity and terminal box suitable upto 63 sqmm cable complete conforming to IS 8828 of 1996 all as specified.

Supply and fixing in repair LED lights fitting 1x 20W, 220V, AC with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and directed.

S & F of Fresh air ventilation fans of 250 mm sweep, speed 1200 RPM, Air delivery not less than 850 m^3 / Min, rated voltage 220-230, 50 Hz, Min two years warranty complete all as specified and directed.

Supply and fixing LED Building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and directed.

M&L for modular AC Box with 20A SP mini MCB, Plastic enclosure & unbreakable Heavy Duty ISI mark Plug Top complete set dully concealed in wall complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

Taking down carefully copper/aluminium any type of point wiring (light/fan/socket /power) complete (fittings such as switches, ceiling roses, holders, sockets, regulators light fittings) and making good the disturbed surfaces of wall/floors/ceiling etc) complete all as specfied & directed.

(c) One 3 pin 5 Amps socket outlet point controlled by one way switch on same board.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in PVC conduit with cable 4 Sqmm size 1100 volts grade including single core stranded FRLS copper conductor 4 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for one modular AC box indepentent board.

S&F of switch piano type 6 amps single pole one way complete all as specified and directed.

S&F of switch piano type 16 amps single pole one way complete all as specified and directed.

S&F of socket outlet multipurpose 2/3 pin 6 amps flush button type complete all as specified and directed.

S&F of socket outlet multipurpose 2 in 1, 6 and 16 Amps complete all as specified and directed.

Supply, laying and drawing submain wiring in and including 20 mm dia concealed PVC rigid conduits including cutting of chases for laying conduit making good the surfaces as per existing surfaces or as directed on walls 02 runs of IC x 10.00 sqmm (Main Cable and neutral) and one run of IC x 10.0 sqmm (as earth wire) of multistranded copper conductor PVC insulated unsheathed cables of 1100 volts grade conforing to IS : 694 of 1990 complete including connection all as specified and directed.

Supply and fix single core PVC insulated cable 1.5 Sqmm FRLS 1100 Volts with copper multi stranded conductor and drawing in same concealed conduits for inverter connection, all as specified and directed by Engr-in-Charge.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades and deposit to MES storeyard, complete all as specified and directed.

Supply, Installation, testing and commissioning of 1200mm sweep BEE 5 star rated, Ceiling fan with Brush Less Direct Current (BLDC) Motor, Class of insulation : B, power factor not less than 0.9, service value (CMM/W) minimum 6.85, not less than 350 RPM (tolerance as per IS:374-2019), THD less than 10%, including electronic regulator unit for speed control and all remaining accessories including safety pin, nuts bolts, washers, temperature rise =75 degree C (maximum), insulation resistance more than 2 mega Ohm, suitable for 230V, 50 Hz, single phase AC supply complete all as specified and directed by Engr-in-Charge including taking down old ceiling fan and depositing to MES store yard.

S&F of factory made epoxy polyester powder coated distribution board SP & N 12 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts, complete all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-54 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs & MCCB's shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F in of MCCB 125 Amp 4 pole 16 KA at 415 V with fixed thermal megnatic release complete all as specified directed.

S&F of single pole MCB 40 Amps, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity including taking down old MCB's complete all as specified and directed.

Supply and fixing in repair suspended linear LED lights fitting 28/30 W, 3000K- 6500 K, 220V, AC comprises of aluminium extrusion, end caps and clutch wire suspension kit for suspended mounting with driver, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fix in repair LED batten luminaire surface mounted system wattage of 20 watts and system lumen efficacy=>100 lm/watt output, power factor=>0.9, color temperature 3000K- 6500 K ,voltage range - 150 to 270 volts AC and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed.

Supply and fix in repair LED batten luminaire surface mounted system wattage of 10 watts and system lumen=>100 lm/watt output, power factor=>0.9, color temperature 3000K- 6500 K and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete mounted in suitable opening arrangement in brick wall/window with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm complete all as specified and directed.

S&F surface mounting LED building security light fitting fitted in high pressure die cast aluminium housing not less than 35 W including fabrication of GI bracket 25mm dia suitable for fixing of LED light fitting duly fixed with clamps, nut bolts & washer etc. Fixture should have minimum efficacy at system level >=100 lumens/watt, CCT 4000-6500K, IP 66 protection with an operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed.

S&F in replacement exhaust fan metallic type ventilating single phase 230/240V of 450 mm sweep with Louvre including cutting of holes in a round shape and including fixing the ventilating fan complete all as specified and directed.

M & L for Earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, burieddirectly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel , connected to earthing test point, earth lead protected by medium grade 15 mm dia GI pipe connected to main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1:2:4 B-1 ( including excavation and earth work, disposal of surplus soil to a distance not exc. 50 Mtrs) all as specified and directed.

M&L far Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burieddirectly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed.

A S CONSTRUCTION CO. (BID ID -3321150)

Chandramauli Engineers Pvt. Ltd. (BID ID -3329382)

Kunal Construction Co. (BID ID -3320989)