REPAIR AND MAINTENANCE OF BED HARD, CHARPOY MS TUBULAR, CHARPOY IP FOLDING, CHARPOY GI PIPE 32 MM WITH CONNECTED WORKS AT ALWAR MLN STN UNDER GE ALWAR

Amount

Removing unserviceable 12 mm thick plywood top from charpoy GI pipe (FD-220) and tightening all check nuts, elbows, long rails, short rails etc. and S & F new plywood top, 12 mm thick plywood, 5 ply, boiling water resistance (BWR) Grade, AA type as per IS 303: 2024 and IS 848: 2006 of size 2020 mm X 900 mm (single piece) with 12 Nos galvanised iron nuts, bolts of 6 mm dia and 70 mm long including sufficient numbers of GI washers of suitable size and thickness on top to maintain the plywood top in levelled position and one GI (heavy duty) washer on the underside before tightening the nuts including embossing MES with paint on all four corners of plywood top as per drawing No: FD-220 complete all as specified and as directed.

Removing unserviceable stiffeners from charpoy GI pipe and S & F new stiffeners of 32 mm X 32 mm X 1.6 mm mild steel pipe conically slanting cut at the ends and flush welded to the top edge of long rail including painting with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer and including making one hole on stiffener for tightening of plywood with nuts, bolts, washers etc complete all as specified and as directed.

Dismantling old broken/ unserviceable long rail and S & F 32 mm nominal dia galvanised mild steel tube, medium grade, ISI marked as per IS 1239 (Part-1): 2004 as new long rail for GI charpoy as per FD-220 including threading at both ends and provision of two check nuts of 6 mm thick suitable for 32 mm bore pipe complete all as specified and as directed. (Note: Each long rail shall be measured separately.)

Dismantling old broken/ unserviceable short rail and replacing the same by using the GI pipe obtained under dismantling of long rail by cutting into required size including threading at both ends for GI charpoy as per FD-220 complete all as specified and as directed. (Note: Each short rail shall be measured separately.)

Dismantling old broken/ unserviceable legs and replacing the same by using the GI pipe obtained under dismantling of short rail by cutting into required size including threading at one end for GI charpoy as per FD-220 complete all as specified and as directed. (Note: Each leg shall be measured separately.)

Dismantling old broken/ unserviceable 3 way elbow and provide 3 way elbow suitable for 32 mm bore pipe (weight not less than 415 gms) complete all as specified and as directed.

Removing unserviceable 12 mm thick plywood top and S & F the new plywood top, 12 mm thick plywood, 5 ply, boiling water resistance (BWR) Grade, AA type as per IS 303: 2024 and IS 848: 2006 of size 1974 mm X 904 mm (single piece) in furniture (bed hard) as per drawing No: FD/E6/MAP/08 complete all as specified and as directed.

Removing unserviceable PVC ring/ shoe and S & F the new PVC ring/ shoe in furniture (bed hard) as per drawing No: FD/E6/MAP/08 complete all as specified and as directed.

Preparing steel surfaces and applying two coats of synthetic enamel paints using spray machine including sanding to steel surfaces of "bed hard" as per drawing No: FD/E6/MAP/08 complete all as specified and as directed.

Removing unserviceable 12 mm thick plywood top and S & F the new plywood top, 12 mm thick plywood, 5 ply, boiling water resistance (BWR) Grade, AA type as per IS 303: 2024 and IS 848: 2006 of size 1990 mm X 900 mm (two equal pieces), leaving gap to facilitate folding including 12 Nos galvanised iron nuts, bolts of 6 mm dia and 70 mm long including sufficient numbers of GI washers of suitable size and thickness on top to maintain the plywood top in levelled position and one GI (heavy duty) washer on the underside before tightening the nuts including embossing MES with paint on all four corners of plywood top in furniture (charpoy folding IP with hard top) as per drawing No: FD-388 complete all as specified and as directed.

Preparing steel surfaces and applying two coats of synthetic enamel paints using spray machine including sanding to steel surfaces of " charpoy folding IP with hard top " as per drawing No: FD-388 complete all as specified and as directed.

Removing unserviceable 12 mm thick plywood top and S & F the new plywood top, 12 mm thick plywood, 5 ply, boiling water resistance (BWR) Grade, AA type as per IS 303: 2024 and IS 848: 2006 of size 1974 mm X 874 mm (single piece) in furniture (charpoy with hard top) as per drawing No: FD/MAP-II/01 complete all as specified and as directed.

Preparing steel surfaces and applying two coats of synthetic enamel paints using spray machine including sanding to steel surfaces of “charpoy with hard top” as per drawing No: FD/MAP-II/01 complete all as specified and as directed.

Pleiad Complex On (BID ID -3083860)

KHAZAN SINGH SAWHNEY (BID ID -3090449)

B.S Constructions (BID ID -3083763)

K K Construction Co (BID ID -3090868)

M/s M S CONSTRUCTION (BID ID -3090028)

C.P.Computers (BID ID -3090511)