PROVN OF OVER HEAD SHED WITH HARD STANDING FOR 10 x B VEHICLE NEAR BLDG NO P 90 WKSP REPAIR SHED AT 229 FD WKSP COY OF 607 EME BN AND OTHER SANCTIONED WORK UNDER GE WEST FEROZEPUR CANTT

Amount

Dismantling of brick tiles in roof single layer jointed & pointed in cement mortar including removal of grass vegitation including roots near outlet of RWP and OHT staging area or specifically ordered by Engineer -in -Charge in writing, complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L 10 mm thick screed bed or bedding layer of mortar in CM(1:4) with water proofing compound @3% by weight of cement or as per manufacturer instructions will be on surface to have a smooth surface. Note: WPC shall be measured and paid separately

M&L for 15mm thick on fair faces of brick work or concrete surfaces in cement mortor 1:4 mixed with water profing comund @3% by weight of cement content as in verticle surfaces and finished even and smooth without using extra cement. Note: WPC measured and paid seperately.

Supply only water proofing compound.

M&L for tack coat of industrial bitumen 85/25 @ 1.20 Kgs per Sqm over a coat of bitumen primer @ 0.30 litre per Sqm including preparation of roof surfaces complete all as specified.

S&F 50 micron thick Polythene film, laid on a roof including preparation of roof surfaces complete all as specified & directed by the Engr-in-Charge.

M&L for 80mm thick average consolidated thickness mud phuska on flat roof including 25mm thick mud plaster complete.

S & F 40 mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar(1:3) mixed with 5% of crude oil by wt of cement on mud phuska complete all as specified and directed.

All as per item No 10 herein before but using old brick tiles retrieved from dismantling (Item No 01 hereinbefore) including cleaning and removal of mortar from tiles. complete all as specified.

M&L Plain Cement concrete (1:2:4), type B-0 using 12.5mm graded stone aggregate min radius of 75mm tk as in roof and parapet wall junction, roof benching, kerbs, mud stop, coping, rounded or chamfered on edges, incl necessary sloping on roof including form work complete all as specified.

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on any face of brick wall or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified.

M&L for 10mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for 5mm thick rendering in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified.

Dismantling of floor hearth and wall tilling incl mortar beding removing serviceable tiles to store and rubbish off the premises as directed by the Engr-in-Charge

M&L for 25mm thick cement concrete (1:2:4) type B-1, using 20mm graded stone aggregate as in floor and finished even and rough to receive the topping layer complete all as specified and directed by Engr-in-Charge.

M&L for Non skid ceramic coloured (colour & shade as approved) tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in flooring set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Non skid ceramic coloured (colour & shade as approved) tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in flooring set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Non skid ceramic coloured (colour & shade as approved) tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in skirting set and jointed in neat cement slurry over and including 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Glazed ceramic tiles, coloured (light shade with dark shade boder as approved), of size 300X200 of 7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over and including 10mm thick backing in cement mortar (1:4) complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc.

Kota stone slabs, 20-25 mm thick, machine cut as in flooring of size not less than 0.25 Sqm each, set and jointed in cement slurry over & including screed bed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing (mirror type) complete all as specified.

Kota stone slabs, 10-12 mm thick in riser of steps , dado machine cut as in skirting, set and jointed in cement slurry over & including rendering coat of 15 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing complete all as specified.

M&L for 16-18mm thick coloured marble slab of size not less than 1 Sqm each, machine cut as in cooking platform or in any position, set and bedded in gray cement slurry over & including 15mm thick screed in cement mortar (1:4) and pointed in white cement with admixture of pigment to match the shade of granite including cutting, polishing (mirror type) complete all as specified.

M&L for Grinding/rubbing/polishing to Terrazzo tiles/ Kota stone surfaces to mirror finish complete all as specified and directed.

Demoltion of brick work built in cement mortar of any specification and in any position complete all as specified.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified.

All as per item 24 above here-in-before but using old bricks retrieved from demolition under item 23 here in before including cleaning and removal of mortar from old bricks.

M&L Cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in lintel 1.5 m clear span cills, steps, sesmic and other similar bands, plinth course string courses lacing course, paraphets and railing upto 60cm in height coping kneelers apex stones, bed plates, kerbs not provided, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm and not exceeding 4 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified..

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and removing from site.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each and refixing in the same opening after resecuring or easing.

S&F Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with/without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel ventilator side/top hung with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

Dismantling of steel work including doors ,gates but excluding framed truss etc complete all as specified and directed

M&L for Cutting holes in brick wall exc half bricks but not exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified.

Framed work such as grills grating etc with ends of bars shoulders ans or riveted, or forged in to spikes: framed guard bars barred iron doors ladders framed balusters walk way railing framework of water cooler stand , angle iron in stair steps, iron gate and similar work conforming to fe 290.Gde E-165

M&L for forming jambs etc built in cement mortor 1:6 to openings incl cutting toothing and properly bonding into to old work also facing ,jointoing and pointing to match to existing work complete all as specified.

S&F Pressed steel frames made of 1.25 mm thick MS sheet of profile 105 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

All as per item No 41 hereinbefore but size of profile 125 mm X 60 mm, complete all as specified.

All as per item No 41 here-in-before but size 75x50mm with single rebate.

S&F 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

S&F 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 12mm thick BWR plywood size of members as specified in clause 8.20(a) of MES Schedule Part-I section-8 complete all as specified.

S&F in Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

S&F in repair Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

M&L in repair, 2nd class soft wood fillets, sectional area exc. 3 sqcm and n exc 6 Sqcm, rectangular or triangular in section, wrought finished, fixed with PVC rawl plug & steel screw complete all as specified.

S&F 3 mm thick ordinary quality sheet sheet glass glazing with oil putty and glazing clips fixed complete to wooden/Steel window not exc 0.5 sqm in each pane complete all as speciifed.

S&F 3 mm thick, Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as speciifed.

S&F in repair 3 mm thick ordinary quality sheet sheet glass glazing with oil putty and glazing clips fixed complete to wooden/Steel window not exc 0.5 sqm in each pane including hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips, complete all as specified.

S&F Small articles of I class hard wood (hollock, sheesham wood may be used without financial adjustment), such as hinge blocks, door and window stops, articles not exceeding 200 cubic centimeter each and fixed with steel screws, complete all as specified.

Demolition of boarding of any description and in any position complete all as specified.

S&F 16-18mm Solid PVC board coloured, fixed with screws or adhesive with complete accessaries as in Shutters,partition and shelves with rebates fixed on PVC soild patten of size 40mmX18mmX500mm on three sides complete all as spd and directed by Engineer in charge Make : Rajshri, Echon or equivalent as approved by GE

S&F Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified.

S&F 125mm size, extruded aluminium alloy handles, fabricated type, anodized and fixed with screws complete all as specified.

S&F magnet catchment of specified shape and size for cupboard selves in kitchen ect, complete all as specified.

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2004).

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved.

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified.

S&F PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified.

S&F PTMT handle 125mm long fixed with steel screws complete all as specified.

S&F Extruded Aluminium alloy tower bolt of 200mm length of bolt and fixed with screws, complete all as specified.

S&F 100mm size Butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm size, extruded aluminium alloy handles, fabricated type, anodized and fixed with screws complete all as specified.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F 300 mm Mild steel helical door spring including roller and roller plate complete all as specified.

M&L for welding in running for thickness of metal to be welded n.exc 6mm, complete all as specified.

S&F galvanised steel water tubes 15 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

S&F galvanised steel water tubes 20 mm bore medium grade, with all fittings and fixed complete to walls and ceiling or laid in floors including taking down corroded GI pipe complete all as specified and as directed by Engr-in-Charge.

Taking up or down 15 mm existing steel tubing and connections and Re fixing old steel tubing and connections in new or old position complete to walls and ceiling or laid in floors complete including cleaning the steel tubing all as specified and as directed.

All as per item No.67 here in before but 20mm dia.

S&F 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measure seprately)

S&F 20mm bore brass ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified.

S&F 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & cantilever brackets embedded in cement and sand mortar in wall , overall size of sink 495mmx420mm, bowl size 410mmx330mmx160mm as in repair complete all as specified.

S&F stainless steel plate rack of standard pattern & of size 750x600x250mm thickness of stainless steel sheet shall be 304 AISI including fixing to wall with 4 nos 50 mm screws & pvc rawl plugs complete all as specifed and directed.

S&F Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end)etc suitable for 15mm bore of pipe as in repair complete all as specified.

S&F Soap dish of PTMT fixed to wall with steel screws and PVC rawl plug complete all as specified.

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

Dismantling CI pipe alongwith fittings of 50/75/100mm dia, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

Taking down eaves gutters and rainwater pipes(any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, including cleaning or refixing or removal to store(measured overall as fixed along the centre line over fittings and accessories)

S&F 110mm dia pipes single socketed in any length with rubber ring joints, fixed to wall including distance pieces and incld stack clamps with nuts & bolts, (Make : Prince, Victus, Finolex & Supreme) complete all as specfied and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors (Make : Prince, Kissan, Finolex or equivalent) complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends any radius complete all as specified.

S&F 110mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F PVC (SWR) vent cowl, for 110mm bore pipe complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall (Make : Prince, Kissan, Finolex or equivalent) complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore, PVC (SWR) bends any radius complete all as specified.

S&F 75mm bore, PVC (SWR) branch piece, single (single T) equal or unequal with access door complete all as specified.

S&F in repair, 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement as in repairs complete all as specified.

S&F in repair, 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified

S&F in repair bib taps 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromimium plated.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

S&F in repair 15mm stop valve cast copper alloy with crutch or butterflty handle, screwed down for iron pipe or brass ferrule fancy type chromium plated with long shank and cup (Concealed type).

S&F in repair 15mm stop cock/angle cock cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup.

S&F in repair towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms)

S&F in repair chromium plated shower rose 125mm size with or without swivel joint for fixing in 15mm dia pipe.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified.

M&L for 30mm thick Plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in flooring finishing even and fair (without using extra cement).

M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and directed

S&F 60 mm thick (M-35 Grade) factory made, machine pressed,precast cement concrete interlocking paver block any shape with grey cement and pigment, confirming to IS-15658:2006, set and joints grouted in fine sand, laid over and including 25 mm thick layer of sand cushioning, complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified.

M&L 15 mm thick CM (1:4) as in horizontal and vertical surface of sunken floor portion and mix with SIKACIM (liquid integral water proofing admixture) of ratio 100 gm per cement bag(50 kg), add with 23 ltr of water and all as specified and directed by Engr-in-Charge.

M&L a fillet of 75 mm size shall be provided using PCC (1:2:4) type B1 (using20 mm graded aggregate) mixed with WPC @3% weight of cement content at the junction of vertical and horizontal surfaces of the sunken portion. Note: WPC Measured and paid seperately

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m in sunken portion including cleaning surfaces as specified & directed by the Engr-in-Charge.

M&L PCC (1:5:10) type E2 (using 40mm graded aggregate) in filling under sunken floor portion

M&L 30mm thick PCC(1:2:4) using 20mm graded aggregate as in floor finished without using extra cement.

S&F galvanised steel pipe light grade 40mm bore as in spout of sunken projecting 15cm beyond the face of wall complete all as specified and directed.

M&l for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as directed by Engr-in-Charge and as specified.(Note : Construction joint will be measured and paid seperately)

M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound complete all as directed and specified by Engr-in-Charge.

M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified.

M&L for Washing, rubbing down and stopping of old treated distempered and painted surfaces of walls and applying one coat of cement base paint complete all as specified.

M&L for Washing, rubbing down and stopping of old treated distempered and painted surfaces of walls and applying one coat of oil bound distemper complete all as specified.

M&L for Preparation of old decorated plastered or unplastered surface by brooming down with steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of oil bound distemper complete all as specified.

M&L for White wash in one coat on old plastered surfaces of ceiling including preparation of surfaces complete all as specified..

M&L for Preparation of new plastered surfaces wall and applying two coats of Oil bound distember over a coat of primer complete all as specified.

M&L for Preparation of new plastered wall surfaces and applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for Preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide , complete all as specified.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

Preparation of old wood or wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint on already prepared old wooden surfaces complete all as specified and directed.

M&L for prepration of old painted plastered surfaces of any description over 10cm girth or width, not otherwise describe and applying one coat of synthetic enamel (one tint) paint.

Writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including cleaning and preparation of surfaces complete all as specfied and directed.

M&L for Excavation in post holes (or similar holes) each n.exc. 0.5 cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n.exc. 50m and making good surfaces, complete all as directed.

M&L for Cement concrete 1:2:4, type B-2 (40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and directed

M&L for Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and getting out complete all as specified.

M&L for Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling as mass concrete or in sub base of floors complete all as specified.

Returing, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil, complete all as directed by Engr-in-Charge.

Removing excavated material as soil exc. 250 m and n.exc 500 m, depositing where directed at a level n.exc. 1.5m above the starting point, complete all as directed.

S&F Rolled sections as in post/pillars and Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) Quality 'A' including fabrication, erraction and fixing complete all as specified and directed by Engr-in-Charge.

S&F Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment and fixing complete all as specified and directed by Engr-in-Charge.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long and n.exc 10cm long and dia of shank 11 to 15mm etc complete all as specified and directed by Engineer-in-charge.

S&F Pre painted galvalume aluminium Zinc coating GI based corrugated/crimped steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as specified and directed.

All as per item no. 15, but 0.80mm thick plain sheet in ridges hips, valley gutters drip and straight flashings (length and girth as fixed) with grade of Zinc coating 275 all as specified and directed.

M&L for Hardcore of broken bricks of gauge n. exc 63mm, deposited spread and leveled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified..

M&L for 100mm thick Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floors finishes complete all as specified and directed

M&L for Brushing neat cement slurry with 3.0kg of cement per sqm

M & L for 100mm thick Plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in floor finishing even and smooth without using extra cement, including provision of expansion joints in cement concrete flooring to full thickness (100mm) complete all as directed by Engr-in-Charge and as specified.(Note : Expansion joint will be measured and paid seperately).

M&L for Forming 12mm thick Expansion joints in cement concrete floor 100mm thick, joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and directed.

S & F in repair Bib tap of CP, 15mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule (Make : Jaquar FLR 5047N) complete all as specified.

S&F in repair Pillar tap of CP, 15 mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule (Make : Jaquar FLR 5015) complete all as specified

S&F in repair Angle cock /Stop cock of CP, 15 mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule (Make : Jaquar FLR 5053N) complete all as specified.

S&F Toilet roll holder fancy type, Chromium plated fixed to walls with plug and brass screw in repair. complete all as specified.

S&F CP Health Faucet with 1 Meter Long Easy Flex Tube in Chrome Finish and Wall Hook with N.R.V (Back Flow Preventer) (Make : Jaquar or equivalent) complete all as specified.

S&F Wall hung basin with full pedestal including CP waste fittings, 32mm bore size, waste pipe PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair. (Make : Jaquar FLS WHT 5801 & 5301) complete all as specified.

S&F in repair Single Piece WC of Size:370x685x675 mm, with PP Soft Seat cover, Hinges, Fixing Accessories, Accessories Set, and Cistern fittings, P trap-180mm and connection to drain or out going pipe. (Make : Jaquar CNS WHT 851P) complete all as specified.

M & L for 20 mm thick granite of any type tiles machine cut in skirting /dado, urinal partition including grinding and polishing complete all as specified and as directed .

S&F CP Soapdish Oval /squaretype as fixed in repairs and all as specified and directed.

S&F Vitreous China Urinal, Half stall type, whiteUrinal, bowl type or half stall pattern, basin only including connections to flushing pipe and outgoing pipes fixed in repairs complete all as specified and directed.

Cutting and Screwing for existing steel tubing of 15mm dia for alterations or additions complete all as specified and as directed.

Cutting and Screwing for existing steel tubing of 20mm dia for alterations or additions complete all as specified and as directed.

S & F 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with J- type or L- type hook bolts complete all as specified and directed.

Supply only 38mmx3mm glass dividing strips as in floors complete all as specified.

S & F 1.00 mm thick mild steel ,plain sheet in gates and similar work cut to size ,holes punched including round headed screws clout nails or rivits and fixed to steel framing with plain 40 mm lap joints with rivited or welded incl bending or turning up etc all as specified and directed

Taking down carefully copper /aluminium point wiring (light, fan , socket or power ) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls , floors ,etc.

M&L point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor multi stranded of size 1.5 Sqmm, single core, in and including rigid non metallic PVC conealed conduit, medium grade of suitable size (not less than 20 mm dia) duly ISI marked with all accessories such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, PVC rectangular boards/round blocks (for housing lamp holders and sketch fittings etc) and new MS pressed steel/cast iron sunken boxes of suitable size for mounting switches/bell pushes/sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continous earth wire of size 1.5 Sqmm unsheated stranded copper conductor with green PVC insulation connected to common earth dolly and finishing surface with match to existing surface complete all as specified and directed for the following:- (a) One light point controlled by one single pole one way switch.

(b) One fan/Exhaust fan point controlled by one single pole one way switch.

(c) One calling bell point controlled by one single pole one way switch.

(d) One socket outlet on the same board controlled by one single pole one way switch

(e) One 5 amps socket outlet independent controlled by one single pole 5 Amp switch.

All as per Item No 2 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing complete.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp complete all as directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked.

Supply & Fixing Socket outlet 5 pin , 5/6 Amps flush type ISI marked.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked.

Supply & Fixing bell push flush type 5 Amps duly ISI marked.

Supply & Fixing ceiling rose,PVC/Polycarbonate,isolated three terminals.

Supply & Fixing Lamp holder PVC/Polycarbonate,isolated with back plate suitable for batten fittings including 10W LED lamp complete all as specified and directed.

Supply & Fixing bell ding dong type AC 230 Volt single pole.

Supply & Fixing step type regulator Piano switch type ( 5 step) for ceiling fan 1200/1400 mm size 230 volts, 6 Amps.

Supply & Fixing LED tube light fitting 18 Watts,4 feet long decorative ultra slim linear LED lighting fixture with extruded polycarbonate,environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

S & F Bee star rated HS Plus 5 star 1200mm sweep ceiling fan AC 230 Volts with all accessories complete all as specified and directed. Make : Bajaja/Havells/Khaitan/Crompton

S&F exhaust fans AC single phase 230 V, of size 300 mm sweep with louver complete all as specified and directed

Supply & Fixing in repair sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series TPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified

Supply & Fixing in repair sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 8 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching complete all as specified.

All as Item No 21 here and before but SPN DB 4 way.

Supply & Fixing MCCB 63 Amps, 415 volts, 16 KA, 4 Pole complete all as specified.

Supply & Fixing MCB, Single pole 240 V,6 - 32 Amps 10 KA 'B Series.

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series.

M & L in repair sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Supply & Fixing LED Bldg security light 30 watts,pressure die cast aluminium housing,heat resistane toughened glass with frame,IP 66 protection with bracket (for housing street light fittings) made of GI pipe 25 mm dia light grade 0.60 mtrs long duly cutted and welded at an angle of 120 degree and fixed to wall with 50 mm X 6 mm MS clamps - 02 Nos with 16 mm dia bolts,nuts,and washers complete all as specified and directed.

Suplying and fixing 1100 volts grade heavy duty 10 Sq mm two core cable PVC insulated aluminium conductor, served with inner shething of PVC sheeathed in service conections suspended by insulating hangers not more than I metre apart including 4Sq mm suspension wire, one twin core cable flat or circular. Make: Havells/Polycab/Gloster

Supply and lay cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 4 core.

All as Item No 30 here and before but 16 Sqmm 2 core.

Excavation in trenches n.exc 1.5 m wide and n.exc depth in loose/soft soil and getting out for laying of cable and reection pole.

Returning filling in including spreading leveling watering and well ramming in layers n. exc 25 cm in soft/loose soil complete all as directed

Removal of excavated soil n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as per directed

M&L for sand filling under floors, foundation or cable protection including spreding leveling in layer not exc 25cm thick.

M & L sub class B bricks locally available of size 22x11x7.5 cm laid dry width wise acrose the line of cable in trenches for protection of UG cable

Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc as required all as specified.

HAPPY ELECTRICALS

JAWAHAR CONSTRUCTION COMPANY

AKASH ELECTRICALS

Ms Hari Singh

KAILASH CONSTRUCTION COMPANY

Brar Enterprises