Loading
Loading…
Loading…
Tender Value
₹2.1 Cr
EMD Value
₹2.6 L
Closing Date
2 Apr 2026, 2:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
S AND T
14 conditions · 2 needing a document upload
For works amounting Rs.50 lakhs and above: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of 'total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Any Work involving supply, installation, testing and commissioning of SDH and /or PDH equipment (STM-1/STM- 4/STM-16, MUX etc.)
9 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Demand for the Financial Criteria, Association of Railway Officers, List of Arbitration cases, Court cases and Mandate for NEFT are to be uploaded with a scanned copy duly filled in and signed as per annexure no. IV, V, VI, VII, VIII, IX, XI, VIA, VIB, VI and Annexure-V and Annexure- V(A) of GCC-2022 respectively. These Annexures are available in View Document menu at Home page and is downloadable. The details of the uploaded documents should be produced whenever demanded for verification on written request at any point of time of the tender and contract within 7 days.
1. Tenderer must understand the work before quoting. Submission of tender shall be deemed to have been done after careful study and examination of papers as well as work site and understanding of the implication thereof. 2. Quoted rates shall include all types of taxes (including GST), duties, carrying cost of all materials for the work including loading unloading involved in the concerned work. 3. All the supply materials to be deposited at the store of SSE/Tele/Store/ASN. 4. All material supplied by Railway as well as those supplied by the contractor have to be transported from the store of SSE/Tele/Store/ASN to the site of work by the contractor's own arrangement. 5. All released materials as well as any leftover material intact will have to be transported from the site back to the office of the SSE/Tele/Store/ASN by contractor's own arrangement. 6. Any consumables which is required for execution of the work, not mentioned in this schedule as Rly. supply, contractor has to arrange for the same as per advice of Site Engineer. 7. Items supplied by the contractor will be inspected by the authorized representative of Sr. DSTE/ASN or RDSO/RITES as mentioned in schedule of work. Cost of inspection is as applicable. 8.Contractor have to submit indemnity bond for safe custody and protection of railway materials during transportation (sample may be collected from office) 9. Work to be done as per advice of site engineer.
10.The Contractor & his supervisors, staff must take proper precaution during working in Railway area to prevent any interference with existing Rly. system, working & passengers. 11. Care should be taken to avoid damage to existing gears during the work. Any damages to the Railway property shall be made good by the contractor in his own cost. 12. Payment shall be made as per extant works contract procedure based on actual work done. 13. Latest guideline of Railway Bd.'s vide letter no. 2018/CE-I/CT/9 dated 04.06.2018 regarding "Letter of Credit" as Mode of payment in Works Tenders or Service Tenders is attached in pdf file. 14. An Eastern Railway Guidelines (ER cable cut JPO) for protection of cables while digging work in the vicinity of underground Signalling, Electrical & Telecommunication cable (ER letter No.SG.224/13/0, dt.12.08.2024) has been finalised. Accordingly, while working near underground Signalling, Electrical & Telecommunication cable, proper care should be taken to avoid the cable cut, other wise the penalty amount as per Railway Guidelines will be recovered from the erring contractors. 15) PVC clause shall be applicable only in tender having advertised value above Rs.2 Crore vide Railway Bd,s letter no. 2022/CEI/ CT/GCC-2022/Policy, dated 14.07.2022.
Asansol Division: Provision of Telecom Infrastructure for new OFC Room in Asansol Division.
41-SDSTE-ASN-2025-26
41-SDSTE-ASN-2025-26
Open
Works - General
18 Months
Paschim Bardhaman, West Bengal
₹0
₹2.6 L
2 Apr 2026
10 Mar 2026
19 Mar 2026
185 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,43,43,462.08 | ||
| — | 16.00 | — | — | ||
| Supply of PLB-HDPE Duct for UG armoured Optical Fibre Cable diameter 40.0 mm, as per RDSO Specification No. RDSO/SPN/TC/45/2013 Revision 2.0 or latest, in length of 1000mtrs/roll. For each K.M. of HDPE duct pipe following items are to be supplied (a) end plugs-02nos., (b) cable sealing plugs-02nos., (c) plastic couplers slip fit/push fit type-02nos., (d) end plugs to be provided along with drum-02nos. MAKE: WESTERN/Gangotri/similar. Inspection: RDSO. | — | — | — | 10,05,872 | |
| — | 16.00 | — | — | ||
| Laying Of HDPE DUCT 40/33 mm in trenchs and protective works including pulling of single mode armoured OFC Cable( fibre) through duct in trenches as advised by site engineer. Note: (1)Contractor will take over the OFC cable from Railway store to site of work duly checked the continuity of each fiber from end to end (2) before & after cable laying of OFC cable through duct, continuity test from end to end of each fiber to be made by contractor to ensure availability of all fibers duly certified by the site enginner. | — | — | — | 3,95,744 | |
| — | 10.00 | — | — | ||
| Supply of Splice Closure for 24core Optical Fiber Cables Armoured and Metal free type OFC With screws sealing as per as per TEC/GR/TX/OJC-002/03/APR-2010 or latest, including all miscellaneous items & consumables for fiber splicing, make: 3M/Comscope/R&M/Drone Edge/similar, Inspection: Consignee. | — | — | — | 35,580 | |
| — | 18.00 | — | — | ||
| Jointing, terminating and Splicing of 24 Fibre Optical Fibre Cable and fixing of termination Box/FDF/Placing of joint clousers in pit required at various location including tranportation of all the jointing & terminating materials from railway store to the works site and returning leftover materials to the railway store. The rate should include all jointing materials. | — | — | — | 1,91,250 | |
| — | 3050.00 | — | — | ||
| Supply of CAT6 U/UTP Cable for Indoor use, 4-pair unshielded twisted pair (UTP) cable, FR PVC Jacket, High Density Polyethylene insulation, 23 AWG solid copper conductor for superior conductivity, Conductor diameter: 0.57 mm (23 AWG), supports Gigabit Ethernet (1000 Base-T) standard, Make -Molex/DLINK/similar, Inspection: Consignee. | — | — | — | 57,950 | |
| — | 200.00 | — | — | ||
| Fixing of GI Pipe of required length at all road crossing/track crossing which fall on cable route & laying of telecom cable through them & also on bridge/below mettaled road/L- Xing/culvert/track crossing for laying of cable through it. This also includes installation of all materials required for fixing arrangement. At the ends of GI pipe, flexible/corrugated HDPE pipe will be provided by contractor to protect cables from sharp edges & sudden bends. | — | — | — | 19,600 | |
| — | 20.00 | — | — | ||
| Supply of Thermo shrink Universal Jointing kit for Quad Cable (for straight joints) 0.9mm dia as per RDSO spec IRS/TC-77/2012 revision 3 With latest Amdt. Inspection: Consignee. | — | — | — | 43,700 | |
| — | 20.00 | — | — | ||
| Execution of Thermo Shrink Jointing Kit as per site engineer's instruction at various location. Cable jointing shall be carried out at site as per the detailed procedure suggested by RDSO approved manufacturers of thermoshrink jointing kit for PIJF & 6-Quad cable. Jointing kit will be supplied by Railway. Inspection: Consignee. | — | — | — | 19,120 | |
| — | 16.00 | — | — | ||
| Excavation of OFC pit for cable jointing of size 1.5m x 1.5m x 1.2 m for all type of soils. The section. Back filling the pit and ramming after jointing. Provision of brick walling the four walls and bottom of pit with RCC slab, back filling with earth and ramming as per drawing. N.B. all the materials including cement required for the above will be supplied by the tenderer. | — | — | — | 1,06,784 | |
| — | 50.00 | — | — | ||
| Cement concrete work for miscellaneous items in the ratio 1: 3: 6. Item includes excavation, ramming, curing and plastering with cement & sand mixture (aggregate not exceeding 3.8 cm.) (Aggregate cement & sand to be supplied by the contractor). Wherever depth of 0.5 m cable trench is not feasible, cable shall be protected as: - Preparation of cement mixture 1:3:6 with contractor's own materials and spreading cement concrete mixture layer of 100 mm thick over the already laid cables in the excavated trench. | — | — | — | 1,79,800 | |
| — | 300.00 | — | — | ||
| Supply of Power cable 3 core, 2.5sq. mm. PVC insulated power cable with ISI marks confirming spec. IS:694:1990 reaffirmed 1995 or latest. make: Finolex/Polycab/Havells/similar, Inspection: Consignee | — | — | — | 18,300 | |
| — | 20.00 | — | — | ||
| Supply of 2 MB Programmable Primary Digital drop insert multiplexer as per RDSO Specs. IRS:TC:68/2012 (Rev.0) or latest with conference facility and other stipulation to tender documents and fully wired for 30 channels complete with power supply card, remote control, supervision facility and all other accessories, installation material, manuals etc. It should have facilities to accommodate data interface card in multi drop mode and should be able to support cards needed for video conferencing and ISDN. It shall support NMS installed at Test Room and may operate local/remote location of entire section. It also includes submission of all technical documents, manuals and supply of all miscellaneous items which will be required for final testing and commissioning of system. The above MUX should be equipped with following circuits: - i) 2 wire/ 4 wire E&M VF circuits ( minimum 16 nos ckts) ii) Subscriber loop circuits ( minimum 4 nos ckts) iii) Exchange loop interface circuits (minimum 8 circuits ) iv) This also includes connecting all pigtails, optical patch cords etc. to the SDH equipment. This also includes connection of SDH and primary MUX equipment with all interface cards to the 48V Bus including supply of wires and connectors termination of all evens on DDF taking PVC cable over runway or a wall and termination of VF interface circuit to the Krone type. Note: The materials to be procurred from RDSO approved vendor. Inspection: RDSO | — | — | — | 29,86,160 | |
| — | 20.00 | — | — | ||
| Installation, wiring, testing and commissioning of 2 MB Programmable Primary Digital drop insert multiplexer as per RDSO Specs. IRS:TC:68/2012 (Rev.0) or latest with conference facility and other stipulation to tender documents and fully wired for 30 channels complete with power supply card, remote control, supervision facility and all other accessories, installation material, manuals etc. It should have facilities to accommodate data interface card in multi drop mode and should be able to support cards needed for video conferencing and ISDN. It shall support NMS installed at Test Room and may operate local/remote location of entire section. It also includes submission of all technical documents, manuals and supply of all miscellaneous items which will be required for final testing and commissioning of system. The above MUX should be equipped with following circuits: - i) 2 wire/ 4 wire E&M VF circuits ( minimum 16 nos ckts) ii) Subscriber loop circuits ( minimum 4 nos ckts) iii) Exchange loop interface circuits (minimum 8 circuits ) iv) This also includes connecting all pigtails, optical patch cords etc to the SDH equipment. This also includes connection of SDH and primary MUX equipment with all interface cards to the 48V Bus including supply of wires and connectors termination of all evens on DDF taking PVC cable over runway or a wall and termination of VF interface circuit to the Krone type. All materials such as wires for Earthing & power supply, wire carrying aluminium ladder, MCB, Connectors, foundation bolts, nuts, base frame, mounting accessories for fitting of transformers, U-Link Panels, inter connecting cables etc. required for the above shall be supplied by the contractor. | — | — | — | 2,27,440 | |
| — | 10.00 | — | — | ||
| Supply of Tributary interface card of Webfil make PD Mux (flexi Mux) as per Specification No. IRS: TC 68/12 Rev.0 with amendment no 1 or latest. Inspection: Rites | — | — | — | 4,80,507.8 | |
| — | 10.00 | — | — | ||
| Supply of Network interface module (NIM) interface card compatible with existing PD Mux (flexi Mux) as per Specification No. IRS: TC/ 68/12 Rev.0 with amendment no 1 or latest. Inspection: Rites | — | — | — | 3,16,912.6 | |
| — | 20.00 | — | — | ||
| Supply of Subscribe loop interface cards of compatible with existing PD Mux (flexi Mux) , minimum 4 circuits per card. Inspection: Rites | — | — | — | 2,45,040 | |
| — | 10.00 | — | — | ||
| Supply of Exchange loop interface card, compatible with existing PD Mux (flexi Mux), 6 circuits per card. Inspection: Rites | — | — | — | 81,510 | |
| — | 10.00 | — | — | ||
| Supply of 2W/4W E&M interface cards compatible with existing PD Mux (flexi Mux), minimum 4 circuit per card. Inspection: Rites | — | — | — | 1,20,240 | |
| — | 10.00 | — | — | ||
| Supply of surge suppressor for all the 30 circuits derived from the Primary MUX (Z protection). Inspection: Consignee. | — | — | — | 65,540 | |
| — | 10.00 | — | — | ||
| Supply of standard 19"rack mountable , -48V DC working, Add-Drop STM-4 SDH equipment conforming to GR No. TEC/GR/TX/SDH - 010/03.Jan 2011 (with latest amendment) complete with redundant power supply, 2 no. STM 4 of aggregate L.4.2 Optical interface modules/Cards one each for East and west side, TX/RX and 2 nos. of STM-1 S 1.1 optical interface modules complete with 5 mtrs long optical fibre cords, 21 E1s with DDFs and cable assembly for termination to DDF and minimum 8 nos. of 10/100 Base-T Ethernet ports, Fast Ethernet on SDH [EoS] 10/100 Base-I interface module/card supporting with LCAS and GEP, order wire sub Rack DDF installation material, manuals and other accessories. Complete Engineering order wire (EOW) arrangement. Necessary/Firmware for local/remote monitoring/configuration of the equipment through EMS and Software/Firmware interface to work all Network elements as Gateway Network Element [GNE], 2 nos of MCBs of appropriate rating and necessary connecting cords and cables for power supply modules. Inspection: Rites | — | — | — | 19,92,280 | |
| — | 10.00 | — | — | ||
| Installation and commissioning of STM-4 in the existing rack with ready infrastructure or in new rack as desired by the site Engineer. | — | — | — | 2,34,950 | |
| — | 10.00 | — | — | ||
| Installation of 4W way station DTMF equipment as per RDSO spec. no IRS-TC/ 60/ 93 or latest (with 4 wire telephone as per spec. No IRS-TC-38 /97 or latest. Make- Bentron, Epsilon or similar | — | — | — | 12,570 | |
| — | 10.00 | — | — | ||
| Supply of 4W way station DTMF equipment as per RDSO spec. no IRS-TC/ 60/ 93 or latest (with 4 wire telephone as per spec. No IRS-TC-38 /97 or latest. Make- Bentron, Epsilon or similar and supply of 12V/7AH power supply unit for control phone. Inspection: Consignee | — | — | — | 67,100 | |
| — | 10.00 | — | — | ||
| Supply, installation and complete indoor wiring of 19 inch (42U) covered Rack of size 2035 mm x 600 mm x 600 mm (Approx.). The rack shall be complete with all fittings for housing SDH equipment, Primary MUXES, DDF, MDF using crone modules and other equipment like runway ladders etc. completely wired and equipped with integrated protection modules for all channels as per technical specifications and other stipulations of tender document. It should be possible to lock all the equipment with only order wire telephone remaining outside the rack. Conform to DIN 41494 or equivalent standard, Lockable Transparent Toughened Glass Door, rear door Steel Perforated , Castor wheels (Front 2 wheels with Break and rear without break) with Levelers, PDU - Two Number dual input Vertically Mounted 230 Volt PDU, 32AMPs with 25 power outputs with 25 (20 nos. Power outs of IEC 320 C13 Sockets & 5 nos. Power outs of 5/15 amps Sockets), FHU with 4 FAN, 1U Canitlever tray for Modem, Inspection: Consignee. | — | — | — | 3,75,700 | |
| — | 10.00 | — | — | ||
| Installation of Battery chargers, Power distribution Board along with MCBs of suitable ratings and wiring and commissioning of External alarm contacts through EMS. The work includes supply of battery rack, MCBs, battery cable and battery lugs and other accessories required for installation of power plant. Inspection: Consignee. | — | — | — | 45,780 | |
| — | 500.00 | — | — | ||
| Supply of Fire-retardant and corrosion-free 25x25 MM PVC Casing Capping, make Pressfit/PRESTO/SGI/similar, Inspection: Consignee. | — | — | — | 33,000 | |
| — | 10.00 | — | — | ||
| Supply of magneto telephone, desk type, spec. No IRSTC-79/2000 AMDT. 1 or latest. Inspection: Consignee. | — | — | — | 35,090 | |
| — | 10.00 | — | — | ||
| Installation of magneto / control telephone, annunciator with all accessories and dry cells (2 nos.). For each phone with wooden battery box. This includes supply of 2 nos. Dry cell for each telephone with wooden battery box. | — | — | — | 1,950 | |
| — | 3.00 | — | — | ||
| Supply of Digital Multimeter of Fluke 287 Industrial or Similar/ superior True RMS with temperature, Analog bar graph, Digital display, Backlight, 1000V AC/DC, measure up to 10A, 20A for up to 30 second. Battery type 6 AA alkaline batteries, Megohm range Up to 500 M, DC mV resolution: 1 micro V, with all accessories like TL71 Test Leads, AC175 Alligator Clips, Batteries - 6 AA, Item to be supplied after successful demonstration and Approval of Railway. make: Fluke/better, Inspection: Consignee | — | — | — | 1,32,192 | |
| — | 9.00 | — | — | ||
| Installation, testing and mounting of G.P. antenna on a GI pipe which is to be fitted on the roof of equipment room and lightning arrestors also to be mounted on a GI pipe. All fixing materials to be supplied by the tenderer and left-over material to be returned to the railway store. Note: G.P. Antenna, GI pipe (50 mm dia) and lightning arrestor will be supplied by the railway. | — | — | — | 55,710 | |
| — | 9.00 | — | — | ||
| Supply, fixing and wiring of surge protection device in attachment plug module with replaceable surge protection for coaxial signal, interfaces N-connector plug/socket installed as surge protection between antenna and 25 W VHF sets, make- Phoenix Contact model CN-UB-280DC-SB- 2818148 or similar as per specifications. this includes mounting plate and reserve gas filled surge arrestor (one no.) with all required connectors/clamp for commissioning of SPD at site. Inspection: Consignee | — | — | — | 62,865 | |
| — | 9.00 | — | — | ||
| Supply of Buffer amplifier for emergency communication through V.H.F. As per voice frequency channel shall be 600 ohms balanced 4W (viz. 2W for transmit, 2W for receive) and 2W for E&M signalling. The nominal voice frequency signal shall be 0 dbm level the buffer amplifier should work of -48vdc or can from the DC-DC converter. Burn in of the complete equipment at 55 degree centigrade to avoid infancy failures. During the test the equipment shall be kept continuously on. Inspection - Consignee. | — | — | — | 1,24,533 | |
| — | 9.00 | — | — | ||
| Supply of DC-DC converter. for emergency communication through V.H.F. as per specification - the DC DC converter shall be independent for each vhf base equipment (voice equipment) and shall allow to work from -48V nominal input (-48V to -60V variation) & output 12V DC. The power capacity to deliver 10A current with output short circuit protection & ripple voltage less than 5mv for telecom circuit. Short circuit current not more than 2 mA, input-output insulation by 2.5 KV, load & output regulation +/-1% with ERTL certification. Make: DACS, Pune or Webfil Kolkata or Machronics, Kolkata or similar. Inspection: consignee. | — | — | — | 1,86,678 | |
| — | 9.00 | — | — | ||
| Supply of Optic Fibre Cable 6 Core(Single mode) armoured, as per TEC Spec. TEC/GR/OFC-02/03.Sep.2003 or latest, Make: FINOLEX CABLES LIMITED/Usha martin/STERLITE TECHNOLOGIES LIMITED/BIRLA CABLE LIMITED/similar, Inspection: Consignee. | — | — | — | 3,74,832 | |
| — | 10.00 | — | — | ||
| Supply of 48Volt/200AH maintenance free VRLA Batteries duly charged as per IRS Spec. No. S-93/96(A) with amendments-1 or latest. Inspection: RDSO | — | — | — | 8,93,930 | |
| — | 10.00 | — | — | ||
| Installation, wiring, testing & commissioning of 48Volt/200AH maintenance free VRLA Batteries duly charged as per IRS Spec. No. S-93/96(A) with amendments-1 or latest. Inspection: Consignee | — | — | — | 61,900 | |
| — | 10.00 | — | — | ||
| Supply of SMPS based Battery Chargers as per RDSO Spec for Telecom use 48 volts, 25 Amps in 2+1 configuration modules of 25 Amps with ultimate expandable capacity 50 Amps, automatic switching between the modules as per RDSO Spec No. RDSO/SPN/TC/23/1999 version 4 or latest along with two potential free contacts. Inspection: RDSO | — | — | — | 9,27,280 | |
| — | 10.00 | — | — | ||
| Supply of power supply unit for telecom installation at way side station suitable to operate max 6 equipment of DTMF type (12V/7AH) battery with suitable battery charger) as per RDSO spec. No. IRS: TC-72-97 or latest. Inspection: consignee. | — | — | — | 37,400 | |
| — | Breakup | for details. | — | ||
| Earthing of S&T equipment, OFC Equipment and power equipment in 09 OFC Rooms etc. along with supply of all requisite materials. Earthing shall be in the form of Ring Earth/Perimetric earth conforming to RDSO spec RDSO/SPN/197 Ver.1.0 or Latest and as per latest TAN of RDSO No. RDSO/TAN/3006, Ver 3.1 of Earthing and Bonding system. The earthing shall be maintenance free. The ring earth/perimetric earth shall be connected to copper flat of size 25x2 mm ( BRC) in the OFC Room. The copper flat fixed on the wall to the entire breadth of OFC room as an earth bus bar and all earth connections shall be taken from it. Supply, installation commissioning of this work of Earthing and Bonding system to be done at 09 nos. locations (OFC Rooms) as per RDSO/TAN/3006, Ver 3.1 with latest amendment with item details given in break up | — | — | — | 20,86,591.68 | |
| Supply of KRONE TOOL for inserting wire into insulation displacement connectors similar to krone make, Features: a. Ensures proper insertion of wire b. Cuts excess wire in one click operation c. Swing out hook, used to pull out connected wire d. Swing out blade, used to remove module from BMF. Conductor diameter of connectable wires: 0.40 to 0.80 mm, Insulation diameter of connectable wires: 0.7 to 1.6 mmmake: Krone/similar. inspection: consignee. | — | 10.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
MergedGCCCorrectionSlip78910.pdf
ATTACHMENT
TenderDocument_SnT.pdf
ATTACHMENT
GCC_April-2022.pdf
ATTACHMENT
GCC Correction Slip
ATTACHMENT
GCC Correction Slip2
ATTACHMENT
mergedGCCCorrectionslip3456.pdf
ATTACHMENT
2018-CE-I-CT-9dtd.pdf
ATTACHMENT
Annexure-C.pdf
ATTACHMENT
AllAnnexure.pdf
ATTACHMENT
CheckList.pdf
ATTACHMENT
CABLECUT_DiggingJPO_12.08.2024.pdf ER cable cut JPO
ATTACHMENT
Quad Cable termination box
ATTACHMENT
2022_CE-I_CT_GCC-2022Policy14.07.2022.pdf
ATTACHMENT
ACS-2toGCC-2022_2022-CE-1-CT-GCC-2022-POLICY_13.12.20221.pdf
ATTACHMENT
CABLECUT_DiggingJPO_12.08.2024.pdf
ATTACHMENT
TELE-BOX-QuadTerminationBox_2025latest.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .