Special Repair of Door, Windows, Fly Proofing, Roof, Plastering, Ceiling and Periodical Services Of Non Resdl/Office Bldg for Jorhat Garrison and ARDTC

Amount

Dismantling out door, windows and clesestory shutters (steel or wood ) incl stacking within within 50 m lead of sectional area 3 sqm or below.

Providing & fixing wood work in frames of doors, windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of reqd dia and length, 2nd class hard wood.

Providing and fixing angle iron frames for doors, windows and ventilators of MS angle sections of size 45x45x5 mm incl necessary bolt, hinges and screws and applying priming coat.

Providing and fixing ISI marked flush door shutters conforming to IS 2202 (part-I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains on both faces, 35 mm thick.

Providing and fixing 1 mm thick MS sheet door with frame of 40x40x6mm angle iron and 3 mm MS gusset plates at the juncton and corners, all necessry fittings, complete using flats 30x6mm.

Providing and fixing wire gauge shutters using gal MS wire gauge of average width of aperture 1.4mm in both directions with wire of dia o.63 mm, for doors with hinges 30 mm thick.

Providing and fixing alum window double shutters incl. frame with built up appropriate Z sections and other sections of approved make incl providing and fixing hinges/pivots and making provn for fixing of fittings wherever reqd incl the cost of EPMD rubber/neoprene gasket, 4 mm thick glass panes and wire mesh, all complete.

Providing and fixing glazed shutters for windows using 4mm thick float glass panes, incl. ISI marked MS pressed but hinges with all necessary scews, 35 mm thick of 2nd class hard wood.

Renewing 4 mm glass panes, with putty and nails wherever necessary.

Providing and fixing alum dia cast body tubular type universal hydraulic door closer, door weitght upto 35 Kg with all accessories and screws etc complete.

Providing and fixing fly proof galvanised M.S wire gauge to windows and ventilators using wire gauge with average width of aperture 1.40 mm in both directions with wire of dia 0.63 mm fixed with 2nd class hard wood beading all complete

Demolishing cement concrete 1:3:6 by means manually incl disposal rubbish as per direction of Engr-in-charge.

Supplying, Laying, Spreading and Compacting stone aggr. of 53mm to 22.4mm size in uniform thickness, hand packing incl watering and compacting to the reqd density.

52mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 and top layer 12mm thick in CM 1:2.

Providing and laying in position cement concrete 40 mm thick 1:3:6 using 20 mm graded aggr.

Providing neat cement punning over plinth protection.

Dismantling old plaster and cleaning the surface incl disposal of rubbish to the dumping ground within 50m lead

15 mm cement plaster on rough side of single or half brick wall of mix CM1:4

12 mm thick cement plaster in CM1:3 finished with a floating coat of neat cement

Hacking of CC flooring incl cleaning of surface etc, complete as per direction of Engr -in - charge

Grading roof for water proofing treatment with cement concrete 1:2:4 using 20 mm or under size aggr.

Providing and laying in situ seven coarse water proofing treatment with APP modified polymeric membrane over roof consisting of Ist coat of bitumen primer @ 0.40 ltr per Sqm , 2nd, 4th & 6th coarses of bonding material @ 1.20 Kg/Sqm which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layer of roofing membrane APP modified polymeric membrance 1.5 mm thick of 2.25 Kg/Sqm weight consisting of five layer prefabricated with centre core as 20 micron etc over 12 mm layer of CM 1: 3 finished with neat cement with WPC all as per DSR 19 item Code No 14.86

Dismantling wood work in frames, trusses, parlins and rafters upto 10m span and 5 m height incl stacking the materials of sectional area 40 Sqcm or above

Providing & fixing wood work in frames of trusses, partition etc, sawn and fixed in position with necessary stainless steel screws 2nd class hard wood

Dismantling G.S sheet incl ridges, hinges, valleys and gutters etc, and stacking the material with 50m lead

Providing and fixing corrugated G.S sheet roofing 0.63mm thick incl vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm Diameter with bitumen and GI limpet washer incl of the coat of primer and coats of primer

Providing & fixing ridges or hips of width 60 cm overall width plain G.S Sheet fixed with polymer coated J or L hooks, bitumen washers.

Providing and laying ceramic glazed floor tiles of size 300x300 mm of 1st quality of approved make in colours such as whites, Ivory, Grey etc, laid on 20 mm thick CM1:4 incl painting complete.

Dismantling tiles work in floors and roofs laid in CM incl stacking of thickness 10 mm to 25 mm

Providing and laying vitrified floor/riser tiles in size 600x600mm of approved make in all colours and shades laid on 20 mm thick CM 1:4 incl grouting joints, complete

Providing and fixing 15mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved taxture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel section contisting of main 'T' runner suitably spaced at joints to get reqd length and size 24x38 mm made from 0.33 thick sheet , all as per DSR 19 item code No 12.53

Providing and fixing plain multipurpose cement board 6 mm thick (high pressure steam cured) with suitable screws to fix board in ceiling cement fiber board etc, complete

Distempering with 1st quality acrylic distemper (ready mix) having voc content less than 50 gms/ltr of approved brand and manufacture to give an even shade one or more coats on old surfaces incl preparation of surfaces.

Finishing walls with Acrylic smooth exterior paint of required shade, one or more coats of old surfaces incl preparation of surface

Painting with synthetic enamel paint of approved brand and manufacture of reqd colour to give an even shade one or more coats on old surface

Providing and fixing 2nd class teak wood plain living tongued and grooved, incl wooden plugs complete with necessary screws and priming coat on exposed surface 25 mm thick eave board

Providing and fixing wind ties of 40x6mm flat iron section

.Dismantling A C Sheet roofing including ridges, hips, valleys and gutters etc,and stacking the materials within 50 metres lead.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Providing and fixing plain Multipurpose Cement board ( High Pressure steam cured ) as per IS : 14862, with suitable screws for fibre cement incl GI sheet board in ceiling etc. complete (frame work to be paid separately) : 6 mm thick cement board Screw Grid frame.

Providing & fixing Ply wood 7 ply, 9 mm thick9.7.4.1 Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and size Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

15 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in different sizes, conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of CM 1:3 incl grouting the joint with white cement & matching pigments etc.complete, Size of tiles 600x600 mm

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid each

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required : single half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete 40 mm dia

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing uplasticised PVC connection pipe with brass unions : 18.21.1 30 cm length 45 cm length 15 mm nominal bore

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology. 15 mm nominal bore

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm dia

--Ditto-- but single socketed pipes. 75 mm dia

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend each.

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 mm bend each

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for nplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door 110x110x110 mm each

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, incl jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door 75x75x75 mm each

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm dia

Constructing brick masonry manhole in cement mortar 1:4 with R.C.C. top slab with 1:2:4 mix stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix inside plastering 12 mm thick with cement mortar 1:3 finished with floating coat of neat cement and making channels in cement concrete 1:2:4 stone aggregate 20 mm nominal size finished with a floating coat of neat cement complete as per standard design : 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internaldimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix stone aggr 20 mm nominal size cement plastered on both sides with cement mortar 1:3 finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 19.21.1 For pipes 100 to 250 mm diameter each

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 each

Cement concrete flooring 1:2:4 finished with a floating coat of neat cement, incl cement slurry, but excl the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed torequired colour or shade, with nuts and screws etc. complete : 300x16 mm each

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm each

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore metre

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore each

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore each

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore each

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore each

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :14.66.1 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Earth work in surface excavation n exc 30 cm in depth but exc 1.5m ,n width as well as 10 sqm on plan incl getting out and disposal of excavated earth upto 50m.

15 mm thick cement plaster finished with a floating coat of neat cement of CM 1 4

lanck work on edge flooring with bricks on a bed of 12mm CM. inct filling the Joints with same mortar wrth non-modular bricks in CM IA

25 mm thick kota stone Hoeing over 20 mm (average) thick base laid over and jointed with gray cement slurry mixed with pigments, inci. rubbing and polishing complete wrth base of CM1.4.

Providing and laying 60mm thick factory made cement concrete Interlocking paver block of M-30 grade made by block making machine with strong vibrating compaction. of approved size, design and shape laid over and incl. 50mrn thick compacted bed of sand filling complete.

Providing and fixing 2nd class wood plain lining tongued and grooved inol wooden plugs complete with necessary screws and priming coat exposed surface 20mm thick

Providing and fixing plain 6mm thick multipurpose cment board with suitable screws for cement particle board in ceiling complete

Providing and fixing glazed shutter for window using 4mm thick float glass panes incl M.S pressed butt hings and handles 30mm thick 2nd class hard wood

Providing and fixing wire guage shutters using gal M S wire guage of average width of aperature 1.4mm in both direction with wire of dia 0.63mm for windows 30mm thick 2nd class hhard wood

Providing and fixing fly proof gal WS wire guage to doorstwindows using wire guage with average width of aperature 1.4mm in both direction with wire of dia 0.63mm all complete with 12mm M S U beading

Providing and fixing 1mm thick M.S sheet door with frame of 40x40x6mm angle iron and 3mm M.S gusset plate at the Junction and corner, all necessary fittings complete using flat 30x6rnm for diagonal incl priming coat primer

Dismantling W_C pan of all size Inc! disposal of dismantled material ilc malba all complete as per direction of Engr-im-charge

Dismantling flushing cistern of all types incl stacking of useful materials near the site and disposal of unserviceable materials within 50m lead

Providing and fixing water closet squatting pan (Indian type W.0 pan) with 100mm sand cast iron P or S trap. 101itr low level white PVC flushing cistern, incl. flush pipe, with manually controlled device. with all f i ttings and fixtures complete, incl cutting and making good white vitreous china Orrissa pattern complete

Providing and fixing white vitreous urinal basin of-size 430x260x350 mm with 5 litr white PVC automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unions and GI clamp complete, incl painting of fittings and brackets, cutting and making good

Providing and fixing WI-113 size 550x400mm with-a pair of 15mm CP brass pillar taps, CI brackets, waste. incl_ painting of fittings and cutting and making good the walls

Providing and fixing mirror of superior glass of rectangular shape 1500x450mrn approved quality with plastic moulded frame and 6mm thick hard board backing.

Providing and fixing CP brass bib cock of approved quality conforming to IS: 8931 15mm nominal bore

Providing and fixing CP brass stop cock of standard design and of approved make conforming to IS; 8931, 15 mm nominal bore

Providing and fixing GI pipes complete with Cl fitting and clamps incl cutting and making good the wall etc. 20 mm dia nominal bore in external wall

Dismantling CI pipes inch excavation and refilling trenches after taking out the pipes upto 150mm die

Supply, laying, spreading and compacting 53mm to 22.4mm stone aggregate in uniform thickness watering and compacting to the reqd density

Brick work with common bumf clay (non - modular) brick of class designation 7.5 in fdn and plinth in CM 1:6

All As per Item No 60 but single tee with door 110x110x110mm

All As per Item No 60 but bend 87.5 of 110mm dia

Providing and laying cement concrete 1:5.10 using 40mm graded aggr upto haunches of PVC pipe inch bed concrete as per standard design

Painting two or more coats with synthetic enema! paint of approved brand and manufacture of reqd colour to give an even shade inch a coat of steel primer

Finishing walls with Acrylic smooth exterior paint of reqd shade, one or more coats on old surfaces.

--Ditto-- but one or more coats on old surfaces

Removing dry or oil bound distemper, water proofing cement paint and the like by scraping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. Distempering with oil bound washable distepmper of approved brand and manufacture to give an even shade: Old work (one or more coats)

Wiring for light pt/fan pt/exhaust fan pt /call bell pt with 1.50 sqmm FR PVC insulated copper conductor single core cable in conceiled wiring in PVC conduit with piano type switch, suitable size M.S box and earthing the point with 1.50 sqmm wire incl replastering the gap and painting complete.

conceiled wiring for 3 pin 5 Amp socket outlet with 2x4 sqmm FR PVC insulated copper single core cable in conceiled wiring incl. loop earthing as required all as per DSR12 Code No 1.12.

conceiled wiring for 3 pin 15/16 Amp socket outlet with 4x4 sqmm FR PVC insulated copper single core cable in conceiled wiring incl. loop earthing as required all as per DSR12 Code No 1.13.

Supplying and fixing modular switch / 3 pin 5/6 amp socket outlet on the existing modular plate & switch box incl connections but excl modular plate.

--Ditto--- but 6 pin 15/16 Amp socket outlet.

Supplying and fixing metal box of 200x250x75 mm deep size on conceiled with suitable size of phenolic laminated sheet cover.

---Ditto--but size 200mmx150mmx75 mm deep.

Supplying and fixing 5Amps to 32 Amps rating, 240/415 Volt, C curve MCB in the existing MCB DB complete, single pole and neutral etc.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wdn block incl connection etc.

Installation, testing and commissioning of resistance type fan regulator incl connection with earthing.

Supplying and fixing 63 Amps , four pole, (three phase and neutral ), 415 volts, (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as reqd.

Supplying, installing, testing and commissioning of 63 amps TPN, 4 way distribution tap off box made of 1.60mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with HRC fuses, intrconnections, earthing etc reqd.

Earthing with copper earth plate 600mmx600x3 mm thick incl. accssories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.70 mtr long etc. with charcoal/ coke and salt as reqd.

Installaation, testing, and commissioning of pre wired, fluorescent fitting/compact fluorescent fitting of all types, with all accessories and tue etc., incl ball and socket arrangement, 2 no rod all approved by dept.

Wiring for circuit/ submain wiring along with earth wire with the 2x16 sq.mm + 1x16 sq mm earth wire of FR PVC insulated copper conductor, single core cable in surface/ recessed med class PVC conduit as required.

SCHEDULE OF CREDITS (a) Unserviceable CGI Sheet

(b) Unserviceable wooden shutter with frames

(c) Unserviceable CP Stop/ bib/ pilar cock

M/S SWETA ENTERPRISES