Up-Gradation of University Guest House at Dr YSP University of Horticulture and Forestry Nauni, Solan ( SH- Civil and Furnishing items etc.)

Amount

Excavation in all kinds of earth work such as pick work, jumper work, including chiseling/wedging etc. and disposal of all excavated earth upto all leads, lifts and disposed earth to be leveled and neatly dressed complete in all respect as per satisfaction of Engineer-in-charge.

Form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu-reinforced concrete complete and plain concrete work including all leads and lifts of material as directed by the Engineer-in-Charge. a) Foundation footings, bases of column etc. and mass concrete.

Providing and laying cement concrete 1:8:16 (one cement : eight sand : sixteen graded stone crushed aggregate 20mm nominal size)and curing complete on slab and floor excluding the cost of form work screed laid under flooring complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (one cement: two sand and four graded stone crushed aggregate 20mm (twenty milimetre nominal size) curing complete excluding cost of form work including all leads, lifts and carriage of material complete in all respect as per satisfaction of Engineer-in-charge. a) Foundation and plinth.

Providing and laying cement concrete 1:5:10 (one cement: five sand and ten graded stone crushed aggregate 40mm (forty milimetre nominal size) curing complete excluding cost of form work in foundation and plinth in all leads and lifts of material as directed by the Engineer-in-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, frame and fixed in position complete in all respect as per satisfaction of Engineer-in-charge .a) Sawl wood.

Providing & laying heavy duty precast cement concrete inter locking paver blocks vibrato compacted upto M-50 grade including border or curb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (one cement : four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base concrete floor to be paid for separately) complete in all respect as per satisfaction of Engineer-in-charge a). 60mm thick inter locking block (NTC make).

Providing & fixing 0.60mm (point sixty milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 micron over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted limpet and rubber washers complete with all accessories as required as per the direction /satisfaction of Engineer-in-charge(Tata/Jindal Make).

Providing & fixing 0.60mm (point sixty milimetre) thick and 60cm wide ridges or hips prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polister of 5 micron over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia & prepainted GI limpet and bitumen washers complete with all accessories as required as per the direction / satisfaction of Engineer-in-charge TATA / Jindal / SAIL make.

Steel/ MS pipe work welded in built up sections trusses and framed work including cuttings, hoisting, fixing in position and applying a priming coat of red lead paint including all leads and lifts of material as directed by the Engineer-in-Charge.

a)In beams, joists, channels angles, tees, flats with connecting plates or angles as cleats in main and cross beams, hip and jack rafters, purlins connected to common rafter and the like.

b) In grating framed guard bars, ladders, railing, brackets and similar work.

Painting two coat (excluding priming coat) on new steel and other matter surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including all leads and lifts of material as directed by the Engineer-in-Charge. a)Enamel paint other than white.

Applying two coats of wood preservative on new wood & wood based surface after including preparing surface by thoroughly cleaning oil grease, dirt & other foreign matter, sand papering & knotting complete in all respect as per satisfaction of Engineer-in-charge.

Polishing two coats with melamine polish of required shade on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler complete in all respect as per satisfaction of Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equalized on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand paper smooth complete in all respect as per satisfaction of Engineer-in-charge.

Removing of vegetation and white/colour washing by steel with brushing and/or scrapping & preparing the surface smooth including necessary repair to scratches complete in all respect as per satisfaction of Engineer-in-charge.

15mm (fifteen milimetre) cement plaster in single coat in fair/rough side on brick concrete/stone walls for interior/exterior plastering with all height including arises internal rounded angles chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth in cement mortar 1:4 (one cement: four sand) including all leads and lifts and material as directed by the Engineer-in-Charge.

Providing and fixing stainless steel ( Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories& stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. complete in all respect as per satisfaction of Engineer-in- Charge.

Providing and fixing 12 mm thick imported pine wood paneling/lining & ceiling with tongued and grooved jointing and wooden screws etc. complete in all respect as per satisfaction of Engineer-in- Charge (Frame work to be measured and paid for separately).

Providing and applying one coat prime seal and two coat roof seal of Dr. fixit on new/old concrete/ masonry/plastered surfaces after and including preparing the surface by thoroughly cleaning by wire brushes and sand papering etc. as required complete in all respect through approved applicator of the Dr fixit company and should give the guarantee for its sustainably for seven year’s on the stamp paper duly attested from the notary and 10% ( ten percent ) of cost of these item will be retained as guarantee to watch the performance of the work done out of which 50% will be released after five year’s if no complaint / leakage noticed and remaining amount will be released after successful completion of guarantee period of seven year’s..

Supplying and installation of study table Load Bearing Capacity- Table Top: 35 Kg. Overall Size (+/-1) mm- Length:1000 mm* Width: 480 mm* Height: 720 mm. with 15mm MDF for table top/drawer front, 14mm MDF for inner drawer left & right side,3mm for drawer bottom,15mm PB for other panels. 0.18mm p v c was vacuum laminating for surface of table top and drawer front, 0.4mm lapping for other panels. Metal Parts: (Material & Coating details). Hardware: (Details) - KD fitting, screw & slides etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of cots having a size Overall Size: Width- 970 mm Depth— 2046 mm Height -901 mm, Material: Bed Structure consists of metal frames made of M S. Channels in 1mm Thickness. Horizontal plinths and bottom plinth are made of 25 mm Thick Pre laminated Particle Board 1S:12823 Class E1 (as per EN13986). Head board is made of 18 mm thick Pre laminated Particle board 1S:12823 Class E1 (as per EN13986) with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue. Tail board is made of 18 mm thick Pre laminated Particle board 1S:12823 Class E1 (as per EN13986).Side rail is made of 18 mm thick Pre laminated Particle board 1S:12823 Class E1 (as per EN13986).Mattress panels of Bed are made of 18 mm thick Pre laminated Particle Board IS: 12823 Class E1 (as per EN13986) with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue .Hard ware: The high quality hardware are used. Construction: Knock Down construction. Packets: 2 packet .Finish :.18 mm thick Pre laminated Particle Board 1S:12823 Class E1 (as per EN13986)is in Imperial Oak shade. Lapping shade is 299P MAKE REHAU etc as required complete in all respect t as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of dressing with stool having a size Overall Size :Depth — 461.0 mm Width -460.0 mm Height— 1710.0 mm Material:2 Panels of Dressing table are made of 18 mm thick Pre laminated Particle Board IS:12823 Class E1 (as per EN13986) .All the exposed edges are edge banded with 0.8 mm thick PVC edge banding glued with Hot Melt EVA glue .Drawer front & Door are made of 18 mm thick Pre laminated Particle board 1S:12823 Class E1 (as per EN13986). Mirror panel is made of 18 mm thick particle board 1S:12823 Class E1 (as per EN13986) with 4 mm thick mirror fixed on to it. Supporting pipe used for fixing the mirror frame is made of MS square pipe of thickness 1.2 mm .Hard ware :The high quality hardware used like Roller Slides, Hinges , mini fix, dowels is of make Hitachi..Construction: Knock Down construction. Packets: 2 Packets. Finish:18 mm thick Pre laminated Particle Board 1S:12823 Class E1 (as per EN13986) is in Imperial Oak shade. Lapping shade is 299P MAKE REHAU Metal pipe is powder coated in shade Metallic Silver Grey to thickness of 50 microns(+-10) etc. as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of Bed side table with drawer having a size 510 mm height into 460 mm width and 461mm depth are made of 18 mm thick pre-laminated particle board IS: 12823 and exposed portion are PVC edge banding glued with hot melt EVA glue along with allied accessories as required complete in all respect t as per satisfaction of Engineer-in- Charge (Godrej / Rockworth / Steel Case/ HNI make).

Supplying and installation of centre table having a Overall Size : Width : 120cm Depth : 60cm Height : 37.8cmTABLE with solid veneer 18 mm thick MDF top and luges of solid rubber wood of required colour and shade etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of easy chair with seat and back assembly. The seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric and moulded Polyurethane foam with PVC lapping all around. The back foam should be designed with contoured lumbar support for extra comfort. BACK SIZE 49.0 cm. (W) x 47.0 cm. (H) SEAT SIZE 49.0 cm. (W) x 44.0 cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density = 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. 3. ARMRESTS: The armrest tops should be injection moulded from black Polypropylene. They should be fitted to tubular armrest supports made of Ø2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated (DFT 40-60 microns). The tubular armrest supports hold together the seat and back. 4 TUBULAR FRAME: The tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated DFT 40-60 microns ) etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of centre table having a size of 1180*600*450 mm. with solid sheesham wood 18 mm top, 35 x 35 mm leg and 15 mm thich bottom shelf of required shade etc complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of sofa five seated ( 3 + 2 ) Three seater having a Overall Size : Width : 189cm Depth : 82cm Height : 90cm Seating Height : 45cm seat and Two seater having a Overall Size : Width : 150cm Depth : 82cm Height : 90cm Seating Height : 45cm seat. The Understructure is made up of combination of plywood & pinewood members. Plywood is 12+1mm thick. [moisture resistance & termite proof as per IS:303] & pine wood are of cross sections 22x64mm, 34x64mm & 16x35mm without having major knots & defects on the surface. Zigzag spring of dia. 3.8mm is mounted on the seat structure using plastic spring mounting clip for support & additional cushioning purpose. ... nomenclature continued to 27.1

Non woven fabric is stapled on the seat structure frame above the spring ashy. to avoid direct contact between the metal springs and the seat foam. This prevents seat foam from tearing. Powder coated MS support pipe is fitted with the wooden seat frame to give additional strength to the structure. Complete understructure is made by gluing, nailing & stapling. Foam: Seat is made of PU foam with density 28 kg/m3 with a top layer of super soft PU foam with density 32 kg/m3. Seat front bottom is stapled with the PU foam with density 28 kg/m3.Upholstery: Seat upholstery is made in polyester fabric with partitions Backrest: Understructure is made up of combination of plywood & pinewood members. Plywood is 12+1mm thick. [moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knots & defects on the surface. . nomenclature continued to 27.2

3mm MDF is stapled on the back of the structure and manjarpat is stapled at the front bottom. Foam: Backrest is made of PU foam with density 28 kg/m3 on the front lumber portion and the shoulder area has super soft PU foam with density 32 kg/m3. This is covered with a top layer of super soft PU foam with density 32 kg/m3. The top surface has foam with density 32 kg/m3. Complete back surface & underarm of backrest is glued with the PU foam with density 28 kg/m3. Upholstery: Backrest upholstery is made in polyester fabric and has a manjarpat cloth for pulling to accentuate the lumbar area. A throw cover is draped over the backrest, which can be dry cleaner. armrest: Understructure: Understructure is made of combination of plywood & pinewood members. Plywood is 12+1mm thick. [moisture resistance & termite proof as per IS:303] & pine wood are of cross section 16x35mm without having major knots & defects on the surface. 2mm cardboard and 3mm MDF is stapled on the structure to provide a surface for sticking foam .Foam: Armrest is made of PU foam with density 28 kg/m3... nomenclature continued to 27.3

Upholstery: Armrest upholstery is made in polyester fabric. Legs: Rubber wood [Grade-A] legs with the M8 stud are fitted at the bottom surface of the Armrest LH & RH. Legs are coated with PU clear coat [matt finish].Assembly: Upholstered seat, backrest, armrest-LH & armrest-RH are assembled together with the M8 bolts, nuts & washer. Then a non-woven is stapled on the bottom surface to cover the structure. Packet: Each packet contains one assembled sofa without legs and a separate hardware packet containing 4 nos. of plastic legs etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make)..

Supplying and installation of revolving chair with SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood. OCP-QLTA-P14.18 and upholstered with fabric and moulded Polyurethane foam with PVC lapping all around. The back foam should be designed with contoured lumbar support for extra comfort. BACK SIZE: 41.0cm. (W) X 46.0cm. (H) SEAT SIZE: 43.0cm. (W) X 41.0cm. (D) 2) HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam should be molded with density = 45 ±2 kgs. /m3 and Hardness load 16 ± 2 kgf for 25% compression 3)ARMRESTS : The armrest should be .made of black integral skin polyurethane with 50-70 Shore A hardness and reinforced with MS insert. The P.U. armrest should be fixed to black powder coated DFT 40-60 microns ) armrest bracket made of 0.5 ± 0.05cm. thk. HR steel4) PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features:-360° revolving type 14° ±2° maximum back-tilt only. .. nomenclature continued to 28.1

Upright position locking. Tilt tension adjustment 4) PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm 5) TELESCOPIC BELLOW ASSEMBLY: The bellow should be 3 piece telescopic type and injection moulded in black Polypropylene 6) PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet (should be :DD 10791 HR) , powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 55.0 ±0.5cm. pitch-center dia. (65.0 ±1.0cm with castors),7 TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of corner table having a size of 600 x 600 x 498mm : All 18mm pre laminated particle board panels are nice Versailles with walnut edge band, PU lamination is high gloss in Ecru shade. All carcass panel are made of 18mm pre laminated particle board with edge banding 1.5mm thickness. Hardware : Hitachi, Construction : Knock down, Finish : All 18mm pre laminated particles board panels are nice Versailles with ail nut edge band, PU laminating is high gloss in Ecru shade etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make).

Supplying and installation of dinning table 8 seater capacity PU Coated a size shall be 2329 Width mm x 1175 Depth mm x 750 Height mm . Top shall be 25 mm thick base material shall be 25 mm MDF board . On top PU painting of minimum 2H hardness with 75% glass as per color chart .Combination color graphics on the centre . Brown Laminate on bottom specially profiled edges for comfort. The Understructure shall be having bend pipe structure of MS powder coated. Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws . Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with understructure and table top. Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Godrej / Rock worth / Steel Case/ HNI make)..

Supplying and installation of dinning chair Body made up of glass filed PP compound, iridium leg bushes to avoid scratches on delicate floor, capable to take 200 Kg weight of vertical load, scratch resistance etc as required complete in all respect as per satisfaction of Engineer-in- Charge (Space wood / Paradise/ Woodland/ Steelcase make).

Supplying and installation of L shape Reception table having a size of front table length 5’-0”, width 2’-6”, corner height 3’-0”, side table length 3’-0” and width 1’-6” .Top 25mm pre-laminated particle board with PVC edge/ teak wood bonding and Leg 18 mm pre-laminated particle board with PVC edge/ teak wood bonding duly polished along with under cabinet i.e three drawer duly locking system etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Supplying and installation visitor three seater outside sitting steel chrome bench having a size of 1830mm length, 670 mm depth and 775 mm height with 40 mm seat height with cross beam made up of powder coated rectangular MSERW tube leg and armrest chrome plated made of cold rolled steel with 0.12=/-0.013 cm thickness. perforated shell seat back shell it is made of chrome plated solid the shell is assembled on the cross beam with help of M bolts etc. as required complete in all respect as per satisfaction of Engineer-in- Charge (Space wood / Paradise/ Woodland/ Steelcase make).

Supplying and installation PVC wash basin cabinet having a size 32” length, 19” depth and 32” height with dressing glass 600 x 450 mm in decorative beading, high neck sensor tap, angle cock including connection in existing pipe line to VIP lounge for 15 mm dia GI pipe, 40 mm PVC pipe , 32 mm CP waste, waste pipe with allied fittings etc. complete in all respect as per satisfaction of Engineer-in- Charge..

Supplying and installation of wooden kitchen service Trolley for home ready to ship product DIY folding unit having a size of 76.2 into 38.1 into 76.2 cm approximate with hand craft by skilled artisans in India using premium quality sheesham wood with inlay work and Natural wood finish with Bottle rack, dispatched in knock down manner etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Supplying, installation, testing and commissioning of split air conditioner (DC inverter type Hot and Cold) 1.0 Ton with all features are to be provided i.e. four way swing, sleep mode, on/off timer, super power cooling, super heating performance, moisture removal, night glow button, feel mode, wireless remote control, auto power restart, Health Ionizer, low voltage startup, anti mild dew, R 32 – DC Inverter compressor healthy titanium dioxide coating upto 67% power saving, 4 metre connecting copper pipe along with AC wire and drain pipe, Titan Gold filter, Photo catalyst Filter, NANO filter, Catch in filter, Anti Bacteria etc. along with voltage stabilizer complete in all respect as per satisfaction of Engineer-in-charge (O General /IFB/ Mitusubhi make).

Supplying, installation, testing and commissioning of split air conditioner (DC inverter type Hot and Cold) 1.5 Ton with all features are to be provided i.e. four way swing, sleep mode, on/off timer, super power cooling, super heating performance, moisture removal, night glow button, feel mode, wireless remote control, auto power restart, Health Ionizer, low voltage startup, anti mild dew, R 32 – DC Inverter compressor healthy titanium dioxide coating upto 67% power saving, 4 metre connecting copper pipe along with AC wire and drain pipe, Titan Gold filter, Photo catalyst Filter, NANO filter, Catch in filter, Anti Bacteria etc. along with voltage stabilizer complete in all respect as per satisfaction of Engineer-in-charge (O General /IFB/ Mitusubhi make).

Supplying and fixing ½ into ¼ inch copper pipe with AC wire complete in all respect as per satisfaction of Engineer-in-charge

Providing and fixing 25mm dia PVC/plastic drain pipe for AC unit complete in all respect as per satisfaction of Engineer-in-charge.

Supplying, installation, testing and commissioning of 32” Full HD Smart LED TV (SONY/Samsung/ LG make) Resolution : HD Full (1366 x768 ) , Refresh rate : 60 hertz, Connectivity : 2 HDMI ports to connect set top box, blue ray players, gaming console/ 1 USB ports to connect hard drives and other USB devices, Sound :20 watt output/ Dolby digital plus, Smart TV feature : Voice assistant, Smart Things App, Personal Computer, Home Cloud, Live cast, Screen share, Music system, Alex Built-in, Voice Control, Clear audio plus, X-reality and wi-fi. Display : LED Panel, Mega Contrast, Pure Color, HD Picture Quality, Slim & Stylish Design. Warranty Information : 1 year comprehensive and 1 year additional warranty on panel by Samsung. Installation : For requesting installation / wall mounting / demo of this product once delivered as required complete in all respect as per satisfaction of Engineer-in-charge ( Sony/ Samsung/ LG Make ) Condition : Warranty of one year on machine and Five year of compressor will be provided at items Nos. 36 & 37. One year free services to maintain the AC and also the release of earnest money after completion of one year as per best performance and is satisfaction of Engineer-in-charge / concerned department.

Vikrant Sharma

Sanjeev Kumar