SPL REPAIR TO CERTAIN BLDGS AND PROVN FOR TOILET BLOCK AT VARANASI CANTT UNDER GE (EAST) ALLAHABAD.

Amount

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work including cutting of reinforcement to facilitate demolition, complete all as specified and directed. NOTE:- The reinforcement obtained out of demolition shall be deposited in the AGE (MES) Varanasi storeyard and shall be taken into charge by the department duly entering into the salvage register.

Demolition of Concrete work (un-reinforced) in ground floors and pavings including floor tiles not exeeding 15 cm thickness (below or above ground level), complete all as specified and directed.

Plain Cement concrete 1:2:4 type B-0 (using 12.5 mm crushed stone aggregate), 25mm thick, as in levelling course, benching, etc, finished even and rough to receive cement mortar screed bed, complete all as specified and directed.

Plain Cement concrete 1:3:6 type C-2 (using 40 mm crushed stone aggregate), 75mm thick, as in sub-base course to floors, finished even and rough to receive cement mortar screed bed, complete all as specified and directed..

Coloured chequered Cement concrete tiles 250 mm x 250 mm x 22-25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors with grey cement and pigments with and including provision of 15mm thick screed bed in CM 1:6 for laying of tiles, complete all as specified and directed..

Plain Cement concrete 1:3:6, type C1 (using 20mm graded stone aggregate), in plinth protection, 75mm thick, finished even and smooth without using extra cement, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store, removing rubbish off the premises, complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm each ,as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm each ,as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm each ,as in vertical surface of walls such as skirting / dado and risers to steps. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10mm thick screed bed in CM 1:4 complete all as specified and directed.

Glazed ceramic coloured tiles [premium quality] as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 450mm x 300mm x 7- 8mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing of tiles in cement mortar 1:4, complete all as specified and directed..

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 20mm thick screed bed in CM 1:4 complete all as specified and directed.

Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including 10mm thick screed bed in CM 1:4 complete all as specified and directed.

Makrana White Marble tiles 30cmx 20cm x 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing, complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Brickwork with flyash bricks, old size straight or curved on plan exceeding 6 metre mean radius, built in CM 1:6, complete all as specified and directed.

Brickwork with flyash bricks, old size straight or curved on plan to any radius in half brick walls, built in CM 1:4, complete all as specified and directed.

Taking down cement plaster on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Rendering 15mm thick, on fair faces of brick work or concrete surfaces in cement sand mortar 1:6, finished surface even and smooth, complete all as specified & directed.

Rendering 15mm thick, on other than fair faces of brick work or concrete surfaces in cement sand mortar 1:4, finished surface even and smooth complete all as specified & directed.

Rendering 5mm thick in CM 1:3 on concrete surfaces in ceiling, finished fair and even smooth, complete all as specified & directed.

GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, complete all as specified & directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil emulsion paint in approved shade over a coat of primer over wall care putty, complete all as specifed and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint in approved shade over a coat of primer over wall care putty, complete all as specifed and directed.

Preparation of new plastered or unplastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

Complete removal of exisitng treatment / finish on walls by scrapper or wire brushes & clean with water and minor wall cracks or holes shall be filled up with oil putty and applying two coats of oil emulsion paint of approved colour over one coat of primer over wall care putty on wall surfaces, complete all as specified and directed.

Complete removal of exisitng treatment / finish on walls by scrapper or wire brushes & clean with water and minor wall cracks or holes shall be filled up with oil putty and applying two coats of cement base paint over wall care putty on wall surfaces, complete all as specified and directed..

Complete removal of existing treatment (any number of layers) from old surfaces of ceiling and applying two coats of white wash, complete all as specifed and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded in any mortar, complete all as specified and directed.

Marble work (of any type, table rubbed and polished), 15-20mm thick, in steps,jambs and pillars, window cills, cooking platforms etc, including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of marble with and including 15mm thick screed bed in CM 1:6, complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections, complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections, complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) for 15mm bore of GI pipe, complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) for 20mm bore of GI pipe, complete all as specified and directed.

Galvanised Steel water tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15mm dia, complete all as specified and directed.

Galvanised Steel water tubes medium grade in any size or length galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 20mm dia, complete all as specified and directed.

Dismantling of water tanks of capacity exc 250 litres but n. exc. 500 litres, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 500 litre capacity (ISI marked), double layered, hoisted and fixed in position including connecting up pipes, complete as specified in SSR Part 1 complete all as specified and directed.

Ball brass valves, high pressure, with polythene float and fly nut, screwed for iron pipe or brass ferrule 20mm bore, complete all as specified and directed.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, 20mm bore, fixed in repair, complete all as specified and directed.

PTMT Nipple suitable for HDPE water tank, 20mm bore, (Minimum weight 45gram), complete all as specified and directed.

PVC low level flushing cistern 'white' with inlet, 10 litre capacity, with float valve including bracket with 32mm dia PVC flush pipe , fixed in repair, complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580mm x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), including provision of lime concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe, CI trap 100mm bore of pipe, fixed in repair, complete all as specified and directed.

Vitreous china wash hand basin white flat back of size 550mm x 400mm excluding chain, plug and porcelain stopper but including brackets and cutting for and pinning in ends of brackets, fixed in repair, complete all as specified and directed.

Chromium plated mild steel soap tray / soap dish any type of approximate size 100mm x 50mm x 10mm, fixed to plugs with CP brass screws, fixed in repair, complete all as specified and directed.

Chromium plated brass shower rose 65 to 90 mm size with swivel joints, fixed in repair, complete all as specified and directed.

Tubular towel rail of brass chromium plated, 20mm dia, D type, 600mm long between flanges, fixed in repair, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 450mm, fixed in repair, complete all as specified and directed..

Bib taps, long shank, cast copper alloy, chromium plated, with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore, fixed in repair, complete all as specified and directed.

Angle valve, cast copper alloy chromium plated with long shank and cup, screwed down, high pressure, with crutch or butterfly handle, 15mm bore, screwed for iron pipe or for unions, fixed in repair, complete all as specified and directed.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup (concealed type), 15 mm bore, fixed in repair, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly-nuts, screwed for iron pipe 15mm bore, fancy type, complete all as specified and directed.

Grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms), fixed in repair, complete all as specified and directed.

MS tubing of 25mm dia with PVC coating for curtain rod fancy type including fancy type PVC rings and CP brackets, socket and knobs (wall to wall or flush to wall) for securing to curtain rod, fixed in repair, complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 sq.m but not exceeding 4.0 sq.m each and removing from site, complete all as specified and directed..

Taking down chowkats or frames not exceeding 1.5sq.m each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down shutter of any description exceeding 1 sqm not exceeding 2 sqm each complete all as specified and directed..

Taking down shutters of any description n exc 1 sq. m each, complete all as specified and directed..

Factory made 35 mm thick, second class hardwood of plain framed, panelled shutter (two panel) with panels of timber flat on both sides feather edged, or of veneered particle board, medium density or particle board with commercial face, complete all as specified and directed..

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured separately.

Preparation of new wooden surfaces & applying two coats of synthetic enamel paint over a coat of pink primer exc 10 cm width or girth, complete all as specified and directed.

Preparation of old wooden surfaces & applying one coat of synthetic enamel paint exc 10 cm width or girth, complete all as specified and directed.

Preparation of old steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, complete all as specified and directed. Note: Reinforcement to be measured and paid separately.

RCC 1:2:4 type B-1 using 20mm graded stone aggregate in Chajjas, complete all as specified and directed. Note: Reinforcement to be measured and paid separately.

Formwork to chullah hoods, chajjas, troughs and similar items including edges for flat rough finished surface of concrete, complete all as specified and directed.

TMT bars 8-10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material & Labour mild steel TMT bars 6 to 10 mm dia used as in stirrups, spacer bars & binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed.

PCC 1:3:6 type C-1 using 20mm crushed stone aggregate as in surface channels and drains including necessary form work if required complete all as specified and directed..

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified and directed. Note: Inner girth shall only be measured and paid.

Plain Cement concrete 1:2:4, type B-0 (12.5 mm crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges using water proofing compound, complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately under respective item of this Schedule.

Factory made Polyvinyl Chloride (PVC) door shutter 30mm thick, made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a UPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a UPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer, complete all as specified and directed.

Factory made UPVC door frame made of UPVC, extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer, complete all as specified and directed.

Rolled mild steel conforming to Fe 410-W (Gde-E- 250) quality-A, sections as in frmaing for cladding, glazing and the like including door frame/ chowkats and fixed with angle cleats and connecting plates, etc, fixed in repair, complete all as specified and directed.

PCC 1:3:6 type C-1 (using 20mm crushed stone aggregate) as in fixing of hold fasts with and including provision of necessary form work if required complete all as specified and directed..

Aluminium anodised, barrel tower bolts of 200 mm length, extruded section, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Butt hinges, 100 mm long, medium weight, cold rolled mild steel, complete all as specified and directed..

Aluminium handles, 150mm size, cast type, anodised, complete all as specifeid and directed.

Aluminium handles, 100mm size, cast type, anodised, complete all as specifeid and directed.

Aluminium anodised hasp and staple, 150mm size, safety type with mild steel hinge pin including bolt to hinge plate, fixed with screws, fixed in repair, complete all as specified and directed..

Second class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including butt hinge etc & all necessary labours; articles n exc 200 cu. cm each, complete all as specified and direcetd.

Butt hinges, 50 mm long, medium weight, cold rolled mild steel, complete all as specified and directed..

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specifed and direcetd.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, fixed in repair, complete all as specifed and direcetd.

Block boards, 18 to 19 mm thick, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber frame-work, complete all as specified and directed.

Continuous (piano) hinges mild steel bright finish or electro galvanized 20mm width of flaps (when open ), complete all as specified and directed..

Second class hardwood plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads, cross sectional area exceeding 13 sq.cm but not exceeding 25 sq.cm, complete all as specified and directed..

Steel window factory made with side hung shutter including box type hinges with steel handle, steel peg stay, complete with glazing bars, dovetailed or welded joint, complete all as specified and directed..

Steel window factory made with side hung shutter including box type hinges with steel handle, steel peg stay, complete without glazing bars, dovetailed or welded joint, complete all as specified and directed..

Steel ventilator with top hung double shutter (i.e. glazed shutter from outside and gauged shutter from inside) including hinges, steel peg stay handles lugs incl guard bars, glazing bars, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in squares, not exceeding 0.5 sq. m in each pane, complete all as specified and directed.

Sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane including hacking out of glass panes, fixed in repair, complete all as specified and directed.

Dismantling of Cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required for 100 mm dia including all fittings, complete all as specified and directed.

UPVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls complete all as specified and directed..

UPVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in floors or trenches, fixed in repair, complete all as specified and directed..

UPVC (SWR) bends / shoe of any radius and 110mm bore, fixed in repair, complete all as specified and directed..

UPVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, complete all as specified and directed..

UPVC(SWR) vent cowl, 110mm bore, complete all as specified and directed..

Dismantling of Cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required for 75 mm dia including all fittings, complete all as specified and directed..

UPVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls or laid in floors or trenches complete all as specified and directed..

UPVC (SWR) bends / shoe of any radius, of 75mm bore, fixed in repair, complete all as specified and directed..

UPVC (SWR) junction single, (Single T) equal or unequal, 75 mm bore, complete all as specified and directed..

UPVC(SWR) vent cowl, 75mm bore, complete all as specified and directed..

Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm bore, complete all as specified and directed.

Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm bore, complete all as specified and directed.

UPVC (SWR) floor trap of 75mm dia, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply, laying, jointing and testing of Salt-glazed stoneware drain pipes of grade 'A', internal diameter 150 mm, laid in trenches and jointed with bends and taper bends, any radius complete with collars CM 1:1, complete all as specified and directed. NOTE:- (a) The rates include for laying pipes level or to falls in trenches, on concrete bed or directly on hard grounds as indicated. Excavation and earthwork shall be measured and paid separately. (b) The measurements shall be net as fixed between the fittings without any allowances for cutting and waste. Quoted rate shall deemed to include all necessary extra joints, waste and cutting.

Concrete bed to 150 mm bore drain pipes including forming cradles, in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate), complete all as specified and directed.

Kitchen sink with drainage board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm, fixed in repair, complete all as specified and directed.

Stainless steel plate rack (utensil rack) of size 600 mm x 750 mm and depth 300mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut / bolts, washer etc, complete all as specified and directed.

Shelf of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (Minimum weight 300gram), fixed in repair, complete all as specified and directed.

Removing / taking down of old water proofing treatment from roof / concrete surfaces, including removal of debris up to a distance 250 metre, complete all as specified and directed.

Plain Cement concrete 1:2:4 type B-1 (using 20 mm crushed stone aggregate) as in roof padding and misc surfaces using water proofing compound, complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately under respective items of this Schedule.

Providing water proofing treatment over cleaned roof surface with APP modified bitumenous membrane weight not less than 3 kg per sqm comprising of the following and testing of following: (a) 10 mm thick rendering or screed bed or bedding layer in cement sand mortar 1:4 mixed with water proofing compound @ 2% by weight of cement, finished surface even and smooth without using extra cement. (b) One coat of Bitumen primer confirming to IS-3384-1965 @ 0.3 Kg per sqm. (c) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sqm confirming to IS-702-1998 for water proofing membrane. (d) Providing APP modified polymeric water proofing membrane having weight not less than 3 kg per sqm with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length. (e) Again Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sqm confirming to IS-702-1998 for water proofing membrane. (f) Spread coarse sand over entire bitumen surafce and than topping with 40 mm thick brick tiles laid over and including provision of 15 mm thick screed bed in CM 1:6 and joints shall be pointed with CM 1:3, complete all as specified and directed.

Supply only Integral waterproofing compound, ISI marked, complete all as specified and directed. NOTE:- The WPC shall be used all as per manufacturers instructions only.

Precast reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in drain cover, cover slab (for manholes) and similar work with plain faces, set in cement mortar 1:4, complete all as specified and directed.. NOTE:- Reinforcement shall be measured and paid separately under respective items of BOQ.

Supply and apply a glass fibre reinforced acrylic modified cementitious coating system. Preparation of surface of sunken portion and glass fibre reinforced acrylic modified cementitious coating system as top coat @1.5 kg/m2 over reinforcement over base etc. Supply and apply a protection plaster (12-15mm) admixed with appropiate water proofing compound @0.10 kg per bag of cement including povision of GI pipe 'medium grade' 20mm bore 50mm length as spout pipe. The product should conform to IS-2645. Cleaning of RCC surface to remove dust, loose particles and grinding

PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sunken floors, paving or similar work, including demolition of cement concrete (unreinforced) including removal from premises, complete all as specified and directed..

Surface excavation in any soil n.exc. 30 cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide or area not exceeding 10 sq.m on plan and depth not exceeding 1.5 m for foundation, for shafts, wells, cesspits, manholes, pier holes etc., and getting out in any type of soil, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete or similar work, complete all as specified and directed.

RCC 1:½:3 (noramal mix) (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc., complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC 1:½:3 (noramal mix) (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC 1:½:3 (noramal mix) (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

RCC 1:½:3 (noramal mix) (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.

Formwork in flat surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed. (Rough Finished)

Formwork in square, rectangular or polygonal surfaces (rough finished) to sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified and directed.

Formwork in flat surfaces (rough finished) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc, complete all as specified and directed.

Formwork in flat surfaces (rough finished) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

Damp proof course, 25mm thick in type B-0 cement concrete 1:2:4, to horizontal or vertical surfaces including necessary formwork, complete all as specified and directed. Note: The rates for cement mortar and cement concrete damp proof courses include for incorporating integral water proofing compound in the manner specified by the manufacturer and in the proportions indicated. The rates do not include for the supply of integral water proofing compound, which if supplied by the contractor, shall be paid separately.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified & directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified and directed. MAKE:-Sintex / Rajshree plastic / Wood Forex, Indore

Aluminium anodised, barrel tower bolts of 150 mm length, extruded section, complete all as specified and directed.

Butt hinges, 100 mm long, medium weight, extruded stainless steel hinge pin, bright polished, complete all as specified and directed..

Aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Plain Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate), in plinth protection, 75mm thick, finished even and smooth without using extra cement, complete all as specified and directed.

PCC 1:3:6 type C-2 using 40mm crushed stone aggregate as in surface channels and drains including necessary form work if required complete all as specified and directed..

Hardcore broken stone of of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed..

PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete including in sunken floors, paving or similar work, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required, complete all as specified and directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), but including provision of cement concrete bedding type C-1, 1:3:6 (using 20mm graded crushed stone aggregate), including provision of CI trap ‘P’ or ‘S’ type 100mm size, outgoing flushing pipe 32mm dia and anti-syphonage pipe, complete all as specified and directed.

Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe), including providing PTMT spreader and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement connecting water pipe and waste pipe, complete all as specified and directed.

Vitreous china urinal partition white of size 310x700 mm, complete all as specified and directed.

Vitreous China wash basin, white, flat back, size 550mm x 400mm fixed on mild steel cantilever brackets of angle 35mm x 35mm x 5mm, including provison of 32mm dia brass waste coupling and 32mm dia PVC waste pipe (rigid quality) including fixing of tap, complete all as specified and directed.

Supply only pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly-nuts, screwed for iron pipe 15mm bore, fancy type, complete all as specified and directed.

Bib taps, long shank, cast copper alloy, chromium plated, with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore, complete all as specified and directed.

PVC low level flushing cistern 'white' with inlet, 10 litre capacity, with float valve including bracket with 32mm dia PVC flush pipe, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts on both ends of length 450mm, complete all as specified and directed.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type (concealed type), 15 mm bore, complete all as specified and directed.

Tubular towel rail of brass chromium plated, 20mm dia, D type, 600 mm long between flanges, complete all as specified and directed.

Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed.

Removing of surplus excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of white wash on walls complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of cement base paint on walls, complete all as specified and directed.

RCC 1:½:3 (noramal mix) using 20mm graded stone aggregate in Chajjas, complete all as specified and directed. Note: Reinforcement to be measured and paid separately.

Pressed steel frames for doors of size 165mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Factory made 30 mm thick, second class hardwood of plain framed, panelled shutter (two panel) with panels of timber flat on both sides feather edged, or of veneered particle board, medium density or particle board with commercial face, complete all as specified and directed..

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (with sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured separately.

Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed.

Mild steel pressed handles, 150mm size, oval type, stove enamelled black, complete all as specified and directed.

Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete, 300mm size, complete all as specified and directed.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured), complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed.

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified and directed.

Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note: (a) The rates of cudappah stone slab includes for all cutting and waste including machine cutting. (b) The rate includes for cutting and polishing by machine.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.

Coloured chequered Cement concrete paving tiles 300 mm x 300 mm x 22-25 mm thick, machine pressed having wear resistance coating or wear proof topping, tile fixed iwith @ 3 kg cement slurry per square metre, laid over and including provision of 15mm thick screed bed in CM 1:6 for laying of tiles, complete all as specified and directed..

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litre capacity (ISI marked), double layered, hoisted and fixed in position including connecting up pipes, complete as specified in SSR Part 1 complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of cement base paint on walls complete all as specified and directed.

Taking down carefully point wiring of any type and any description / caping or concealed [light point, fan point or socket point] including removal of battens, pipes, plug sockets, switches, shades, ceiling roses, light fittings etc complete and making good disturbed surface to match the exisitng, complete all as specified and directed.

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories, including provision of concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 2.8 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 1.5 sq.mm FRLS type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed for the following:-

One light / fan / bell / exhaust fan point, controlled by one one-way 5Amp switch

One light point controlled by two way switch

One 3 pin, 5 Amp socket outlet point on an independent board.

One 3 pin, 5 Amp socket outlet on the same board with other switches

Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 4.0 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/ fan/ bell/ buzzer/ exhaust fan point controlled by one, one way 5 Amp switch including provision of concealed opressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 2.8 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 2.5 sq.mm FR type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed.

Sub main wiring complete with 2 runs of 6 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of PVC rigid conduit 20mm dia and accessories connecting terminal ends to DB's including providing 1 run of 6 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly including taking down existing sub main wiring any type and making good disturbed surfaces to match with existing including sinking of boxes , complete all as specified and directed. NOTE:- (i) Two runs of 6 sq.mm copper conductor, one run of 6 sq.mm copper earth continuity conductor and one run of PVC rigid conduit and with accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.

Switch piano, flush type single pole, one way 5/6 Amp 230 volts all as specified and directed.

Switch piano, flush type single pole, two way 5/6 Amp 230 volts all as specified and directed.

Switches, bell push, flush type, 5 amp, complete all as specified and directed.

Socket outlet, 2 in 1, 2/3 pin, 5/6 Amps 230 Volts, flush type, complete all as specified and directed.

Electric bell ding dong type AC 230 Volt 50 hz single pole, complete all as specified and directed.

Lamp holder, PVC/polycarbonate body with back plate/ cord grip cap suitable for batten/ angle/ pendent fittings, complete all as specified and directed.

LED retrofit lamp of capacity 15 Watt, B-22 holder base with polycarbonate body and aluminium heat sink warm white complete including taking down old / unserviceable CFL / bulb, complete all as specified and directed.

Switch socket combination 2 in 1, 6 pin, 16 Amp flush type universal, 240 Volts, complete all as specified and directed.

Ceiling rose, single phase, PVC / polycarbonate, insulated body, three terminals, surface bakelite sheet 63.5mm dia, complete all as specified and directed.

Sheet metal enclosure for MCB DBs TPN, 4 way, double door, vertical type, 415 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs, complete all as specified and directed.

Sheet metal enclosure for MCB DBs SPN, 8 way, double door, vertical type, 240 V with 200 Amps rated bus bar, complete with incoming / outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs, complete all as specified and directed.

Isolator / MCB SP 6 to 32 Amp, 240 Volt, conforming to 'B' curve, 10kA breaking capacity, fixed in repair, complete all as specified and directed.

RCBO (Residual current circuit breaker with Overcurrent Protection) for earth leakage, overload and short-circuit protection, two pole, 40 Amp, 100mA, ISI marked, complete all as specified and directed.

Earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth lead of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 40mm dia GI pipe 'light grade', watering pipe 15mm dia GI pipe 'light grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL and connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C-1 earth chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40mm thick pre-cast RCC cover (1:2:4), type B-1 (using 20mm graded crushed aggregate) mix with 8mm dia MS bars @75mm c/c both ways, mild steel handle 12mm dia, PGI funnel and wire mesh, 20mm dia GI pipe light grade(ISI marked) for watering, etc complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciifed and as directed. NOTE:- The quoted rates shall also deemed to include the cost of Earth Test point and earth wire and protection pipe upto 7.5 metre beyond the earth plates electrode.

Supply, laying and testing XLPE cable insulated, screened, PVC beded galvanised steel strip or wire armoured, electric power cable (Heavy Duty) 1100 Volt grade with stranded aluminium conductor of 3.5 core 25 sq.mm, including taking down existing old/ unserviceable cable, complete all as specified and directed. NOTE:- Excavation, earth work, sand cushioning and brick protection work shall be measured and paid separately under respective items of this Schedule. MAKE:- Havells / Nicco / Kalinga premium / Universal

GI pipes, light grade, ISI marked, galvanised including short lengths, laid in trenches / fixed to walls / ceilings or laid in floors / laid in ducts / laid under road crossing for cables, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 50mm bore of pipe, complete all as specified and directed. NOTE:- Necessary excavation and earthwork for GI pipe shall be measured and paid separately under respective items of this Schedule.

Spreading of natural, clean and dry river sand in trenches for cable cushioning, including punning the sand upto desired thicknes and consolidated, complete all as specified and directed. NOTE: Punned thickness shall only be measured and paid.

Supply and lay burnt clay fly ash bricks class 'B', modular bricks, laid in trenches for cable protection with length of brick equal to width of trench, complete all as specified and directed.

Ceiling fan regulator flush type, electronic, rotary stepped type, AC 230 V, suitable for any type of ceiling fan, complete all as specified and directed.

Isolator / MCB TPN, 63 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, fixed in repair, complete all as specified and directed.

LED tube light fitting, 20/22 Watt, decorative type, slim aluminium square profile, high Lumen output, energy efficient, direct surface mounting including connecting up with twin core PVC insulated copper conductor of suitable size, including taking down the old unserviceable light fittings, complete all as specified and directed.

LED integral round shape, surface mounting high power LED luminaire, dome shaped opal diffuser lamp of capacity 18 Watt including taking down old unserviceable CFL/ bulb, complete, all as specified and directed. MAKE:- Cat No. BGCML 18 095 WH of BAJAJ or techno-commercially equivalent model in Philips / Crompton / Havells

LED edgelite linear and compact 9W mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser including taking down old unserviceable light / mirror fittings, complete all as specified and directed. MAKE:- Cat No. LHEXAPRP7PN1W009 of HAVELLS or techno-commercially equivalent model in Philips / Crompton / Bajaj

Drilling through bore hole by trenchless technology without disturbing the existing road, complete all as specified and directed.

Supplying, testing and installation of energy efficient five star rating storage water heater (geyser), 25 litre capacity, vertical type, 2 KW, ISI marked including fixing the geyser on wall with and including provision of nut bolts / anchoring bolts and making electric connection and making good disturbed surface of wall to match the existing, complete all as specified and directed. MAKE:- Havells Model : Puro plus GHWAPFTWH025 or techno-commercially equivalent model in Philips / Bajaj

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, complete all as specified and directed.

Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, 20 mm bore, complete all as specified and directed.

Hot water outlet PVC connection , heavy duty made of chromium plated nuts, bolts and flexible tubing 15mm dia, 450mm long, complete all as specified and directed.

Exhaust fans of metallic body heavy duty AC single phase 230 / 240 V, of size 300 mm sweep,900 rpm, with bracket, louver, nuts and bolts including connection with 1.5sq.mm PVC copper flexible wire of appropriate length, complete all as specified and directed. Make: Havells Model Turbo Power or any techno-commercially equivalent model in Bajaj/ Usha/ Crompton

Building security / street LED light fitting 45 Watt IP-66 protection pressure diecast aluminium body, heat resistant glass, including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5m long and fixed on existing GI pipe, fixed to pole or on wall, complete all as specified and directed. Make: Crompton Greaves Cat Part No LSTO-45-CDL or Havells Cat Part No LHETAXU7PN6J045 or any techno-commercially equivalent model in C&S

Taking down / out existing ceiling fan for servicing, greasing, replacement of bearing, safety pin, canopy, fan condensor, clamp, rubber reel, nut / bolts as required at site and cleaning and preparing surface, filling cavities with filler including one coat painting with synthetic enamel paint including down rod of approved white colour including writing of MES No. one fan head and refixing in its original position and making all electric connection, complete all as specified and directed..

Sheet metal enclosure for MCB DBs SPN, 4 way, single door, vertical type, 415 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands, including provision of blanking plate for unused ways, complete all as specified and directed.

Isolator / MCB TPN, 40 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

LED retrofit lamp of capacity 15 Watt, B-22 holder base with polycarbonate body and aluminium heat sink warm white complete, complete all as specified and directed. Make: Havells/ Phillips/ Bajaj/ Crompton

LED tube light fitting, 20/22 Watt, decorative type, slim aluminium square profile, high Lumen output, energy efficient, direct surface mounting including connecting up with twin core PVC insulated copper conductor of suitable size, complete all as specified and directed. Make: Havells/ Phillips/ Bajaj/ Crompton

Sheet metal enclosure for MCB DBs SPN, 8 way, double door, vertical type, 240 V with 200 Amps rated bus bar, complete with incoming / outgoing connection through proper size of lugs and cable glands, complete all as specified and directed.

Isolator / MCB double pole, 63 Amp, 240 Volt, conforming to 'C' curve, 10kA breaking capacity, complete all as specified and directed.

Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep, minimum air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor, complete all as specified and directed. Make: Havells/ Usha/ Bajaj/ Crompton

M/S Akhilesh Enterprises

Prem Singh

HARI OM CONSTRUCTION