PROVISION OF CHILDREN SCHOOL AT JORHAT MILITARY STATION UNDER GE JORHAT

Amount

NOTE:- (Applicable for all parts/items/):- The bidders/contractors are advised to read tender document, all drawings & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Lumpsum price workedout by the tenderer for BUILDING & STRUCTURE WORKS as listed in Schedule ‘A’ Part-I

Lumpsum price worked out by the bidder/ tenderer for SITE CLEARANCE, SITE DEVELOPMENT AND EARTH WORK as listed in Schedule 'A' Part-II.

Lumpsum price worked out by the bidder/ tenderer for INTERNAL WATER SUPPLY as listed in Schedule 'A' Part-III.

Lumpsum price worked out by the bidder/ tenderer for INTERNAL ELECTRIFICATION as listed in Schedule 'A' Part-IV.

Lumpsum price worked out by the bidder/ tenderer for ROAD/CULVERT/ PATH/HARD STANDING as listed in Schedule 'A' Part-V.

Lumpsum price worked out by the bidder/ tenderer for SEWAGE DISPOSAL as listed in Schedule 'A' Part-VI.

Lumpsum price worked out by the bidder/ tenderer for AREA DRAINAGE as listed in Schedule 'A' Part-VII.

Lumpsum price worked out by the bidder/ tenderer for COMPOUND WALL/SECURITY FENCING/GATE as listed in Schedule 'A' Part-VIII.

Lumpsum price worked out by the bidder/ tenderer for EXTERNAL WATER SUPPLY as listed in Schedule 'A' Part-IX.

Lumpsum price worked out by the bidder/ tenderer for EXTERNAL ELECTRIFICATION as listed in Schedule 'A' Part-X.

Lumpsum price worked out by the bidder/ tenderer for DEMOLITION AND DISMANTLING as listed in Schedule 'A' Part-XI.

Sch 'A' Sec-XII (Miscellaneous Items)Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 signifies this fact only.

M & L for Concealed Point wiring with 1.5 Sqmm (nominal cross-sectional area) FRLSH PVC insulated & unsheathed 1100 volts grade multi stranded copper conductor single core cable drawn through and including non-metallic rigid PVC conduit of adequate size with all fittings and accessories including sunk mild steel terminal boxes with 3mm thick plastic laminated sheet top cover complete including FRLSH PVC insulated & unsheathed single core multistranded copper conductor cable of size 1.5 Sqmm green in colour as earth continuity conductor connected to common earth and earth dolly for One light/fan/bell point controlled by one,one way bell push/switch all as specified and directed by Engr-in-Charge

All same as per item No. 12.01 here-in-before but one light point controlled by 2 Nos two way swich

All same as per item No. 12.01 here-in-before but One socket outlet point 6 A on independent board

All same as per item No. 12.01 here-in-before but using wire 2.5sqmm for one light point controlled by one, one way 15 A switch

All same as per item No. 12.01 here-in-before but using wire 4sqmm for One 16 Amp socket outlet on independent board

All same as per item No. 12.01 here-in-before but using wire 4sqmm for Four Nos 5A Socket outlet

All same as per item No. 12.01 here-in-before but using wire 4sqmm for one industrial socket outlet (upto 16-20 Amp) independent.

S & F MCCB, 4 Pole 80 Amps, 16 KA, complete all as specified and as directed by Engineer in Charge.

S & F MCB SP 6 to 32 Amp, rupturing capacity 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge

S & F MCB SP 40 to 63 Amp, rupturing capacity 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge

S & F MCB SPN 6 to 32 Amp, rupturing capacity 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge

S & F MCB SPN 40 to 63 Amp, rupturing capacity 10 KA, 'C' curve complete all as specified and directed by Engr-in-Charge

S & F Ceiling fan 1200 mm sweep (BLDC motor) with remote control, BEE 5 star rated suspended from fan hook including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose to ceiling fan complete all as specified and as directed by Engineer in Charge.

Supply and fixing Exhaust fan 230 mm sweep MS CRCA body metal blades with double ball bearing, metal protective bird guard AC single phase 230V with self closing louvers including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose to Exhaust fan complete all as specified and as directed. Note:- (a) cost for making suitable opening in wall for fixing of exhaust fan is deemed to be included in the lumpsump cost of building.

Supply and fixing Exhaust fan 300 mm sweep MS CRCA body metal blades with double ball bearing, metal protective bird guard AC single phase 230V with louvers including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose to Exhaust fancomplete all as specified and as directed Note:- (a) cost for making suitable opening in wall for fixing of exhaust fan is deemed to be included in the lumpsump cost of building.

S & F 10W LED PC Battern with all accessories enternally prewired and including and connecting of with twin core twisting flexible cord of 0.50 Sqmm copper conductor cable complete all as specified and as directed..

S & F LED light fitting, 2 x 20 watt, (4 Feet) 230 volts, Pendant/surface luminaries with efficient optics ensuring perfectly uniform illumination including suspension (02 Nos) of 1.5 mtr with electronic driver and with best quality diffuser with system efficancy 100 lumens/watt, 2.5 KV voltage surge protection, PF > 0.98, THD < 10% complete with all accessories including and connecting with twin core of PVC insulated 0.75 Sqmm copper conductor cable complete all as specified and directed.

S & F LED light fitting, 1x 20 watt, (4 Feet) 230 volts, Pendant/surface luminaries with efficient optics ensuring perfectly uniform illumination including suspension (02 Nos) of 1.5 mtr with electronic driver and with best quality diffuser with system efficancy 100 lumens/watt,, 2.5 KV voltage surge protection, PF > 0.98, THD < 10% complete with all accessories including and connecting with twin core of PVC insulated 0.75 Sqmm copper conductor cable complete all as specified and directed.

S & F new generation energy saving and environmental friendly long life LED security light 20 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with 32mm bore light grade GI pipe bend to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twin core from ceiling rose to light fittings complete all as specified and directed

S & F LED light fitting, 1 x 18 watt (porch light) round shaped surface mounted LED luminaire, 230 volts, complete with all accessories including and connecting with twin core of PVC insulated 0.50 Sqmm copper conductor cable complete all as specified and directed

M & L for Concealed Sub main Wiring with two run of 6.0 Sqmm (nominal cross-sectional area) FRLSH PVC insulated & unsheathed 1100 volts grade multistranded copper conductor single core cable drawn through and incl PVC conduit of adequates size and fittings and accessories concealed in walls, floors and ceilings complete including one run of FRLSH PVC insulated & unsheathed single core multistranded copper conductor cable of size 6.0 Sqmm green in colour as earth continuity conductor connected to common earth and earth dolly complete all as specified and directed. Note:- Two run of main wire and one run of earth wire shall be measured as 1(one) RM

M & L for RJ-11 telephone socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed.

M & L for PA equipment socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed.

M&L for LAN socket UTP Cat with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed.

M&L for TV socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 600 mmx600 mmx6mm thick burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters deep below normal ground level and filled with alternate layers of charcoal and salt with 15 cm thick layer , connected to galvanised wire earth lead 4mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron, 20 mm bore GI pipe (med grade) for watering, 15 mm bore GI pipe (light grade) for protection of earth lead, including necessary earth work in any type of soil, Earth pit of PCC (1:3:6) type C1 and precast earth pit cover made of RCC (1:11/2:3) type A1 duly reinforced with 8 mm dia TMT bar @ 150 mm c/c both ways, one lifting handle made of 8 mm dia TMT bar embedded in cover slab complete all as specified and as shown in Electrical Plate No 3 of SSR Part-I including testing on completion. complete all as specified and directed.

All same as per Srl Item No.12.26 here in before but with earth lead 25x4mm and 40mm bore for protection

Supply and fixing wall mounted Air Circulator fans 600mm sweep AC with double ball bearing, heavy duty gear box and metalice body & blades single phase 230V with louvers, including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 1.5 sqmm copper conductor from ceiling to fan complete all as specified and directed.

Supply and fixing 120W LED integral flood light luminaire with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP 66 including suitable mounting arrangement at 1.0 mtr from ceiling level including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 2.5 sqmm copper conductor from ceiling rose to fitting complete all as specified and directed.

Supply and fixing 160W LED integral flood light luminaire with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion with IP 66 including suitable mounting arrangement at 1.0 mtr from ceiling level including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 2.5 sqmm copper conductor from ceiling rose to fitting complete all as specified and directed.

Supply and fixing compact IC track mounted CDM spot light suitable for and including 1 x CDM -TC 70 watt complete all as specified and directed.

Supply and fixing IC track for mounting lights as described in item above here-in-before complete all as specified and directed.

S&F double sided LED signage with built in battery back up for 2 Hrs for "EXIT" light, complete all as specified and directed.

S&F single sided LED signage with built in battery back up for 2 Hrs for "Entry" light. complete all as specified and directed.

S&F LED suspension (Chandlier) mounted multi light fixture (9 Nos ) Model No -40542 of make : Philips or equivalent in Bajaj/Crompton Greaves including proper hanging arrangement with brass chain upto reqd height (not more than 12 mtr) complete all as specified and directed.

Supply, installation, testing and comissioning of weather and vermin proof outdoor type LT Panel with canopy factory made, front & back openable, CPRI approved fabricated out of 3.15 mm thick CRCA (Cold Rolled Closed Annealed Cell) sheet compartmentalized design including mild steel channel frame of ISMC 75 at the base of panel only for grouting purpose (fabrication shall be done in transpotable sections) and grouted with PCC using 20 mm graded stone aggregate, duly epoxy powder coated, complete with heat shrink insulated aluminium bus bar of 800 Amps rating, including all connections with aluminium strips. Panel board/box shall be provided with danger notice plate with skull & bone sign, PVC gasket and sealed, making all incoming and out going electrical cable connections with new lugs, glands to be provided at cable entries, entire enclosure shall have a common earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required and all as specified and as directed. Each panel shall be comprising of following accessories:- Incoming (a) MCCB 500 A, 4 Pole, 415 V, 36 KA - 01 No (b) Phase indicating lamp with MCB - 1 set

Supply, installation, testing and comissioning of weather and vermin proof outdoor type LT Panel with canopy factory made, front & back openable, CPRI approved fabricated out of 3.15 mm thick CRCA (Cold Rolled Closed Annealed Cell) sheet compartmentalized design including mild steel channel frame of ISMC 75 at the base of panel only for grouting purpose (fabrication shall be done in transpotable sections) and grouted with PCC using 20 mm graded stone aggregate, duly epoxy powder coated, complete with heat shrink insulated aluminium bus bar of 200 Amps rating, including all connections with aluminium strips. Panel board/box shall be provided with danger notice plate with skull & bone sign, PVC gasket and sealed, making all incoming and out going electrical cable connections with new lugs, glands to be provided at cable entries, entire enclosure shall have a common earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required and all as specified and as directed. Each panel shall be comprising of following accessories:- Incoming (a) MCCB 125 Amps 4 Pole, 415 V, 25 KA - 01 No (b) Phase indicating lamp with MCB - 1 set

Supply, installation, testing and comissioning of weather and vermin proof outdoor type LT Panel with canopy factory made, front & back openable, CPRI approved fabricated out of 3.15 mm thick CRCA (Cold Rolled Closed Annealed Cell) sheet compartmentalized design including mild steel channel frame of ISMC 75 at the base of panel only for grouting purpose (fabrication shall be done in transpotable sections) and grouted with PCC using 20 mm graded stone aggregate, duly epoxy powder coated, complete with heat shrink insulated aluminium bus bar of 200 Amps rating, including all connections with aluminium strips. Panel board/box shall be provided with danger notice plate with skull & bone sign, PVC gasket and sealed, making all incoming and out going electrical cable connections with new lugs, glands to be provided at cable entries, entire enclosure shall have a common earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required and all as specified and as directed. Each panel shall be comprising of following accessories:- Incoming (a) MCCB 63 Amps, 4 Pole, 415 V, 16 KA - 01 No (b) Phase indicating lamp with MCB - 1 set

Supply, installation, testing and comissioning of weather and vermin proof outdoor type LT Panel with canopy factory made, front & back openable, CPRI approved fabricated out of 3.15 mm thick CRCA (Cold Rolled Closed Annealed Cell) sheet compartmentalized design including mild steel channel frame of ISMC 75 at the base of panel only for grouting purpose (fabrication shall be done in transpotable sections) and grouted with PCC using 20 mm graded stone aggregate, duly epoxy powder coated, complete with heat shrink insulated aluminium bus bar of 200 Amps rating, including all connections with aluminium strips. Panel board/box shall be provided with danger notice plate with skull & bone sign, PVC gasket and sealed, making all incoming and out going electrical cable connections with new lugs, glands to be provided at cable entries, entire enclosure shall have a common earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required and all as specified and as directed. Each panel shall be comprising of following accessories- Incoming (a) MCCB 125 Amps, 4 Pole, 415 V, 16 KA - 01 No (b) Phase indicating lamp with MCB - 1 set

Supply, installation, testing and comissioning of weather and vermin proof outdoor type LT Panel with canopy factory made, front & back openable, CPRI approved fabricated out of 3.15 mm thick CRCA (Cold Rolled Closed Annealed Cell) sheet compartmentalized design including mild steel channel frame of ISMC 75 at the base of panel only for grouting purpose (fabrication shall be done in transpotable sections) and grouted with PCC using 20 mm graded stone aggregate, duly epoxy powder coated, complete with heat shrink insulated aluminium bus bar of 400 Amps rating, including all connections with aluminium strips. Panel board/box shall be provided with danger notice plate with skull & bone sign, PVC gasket and sealed, making all incoming and out going electrical cable connections with new lugs, glands to be provided at cable entries, entire enclosure shall have a common earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required and all as specified and as directed. Each panel shall be comprising of following accessories:- Incoming (a) MCCB 250 Amps, 4 Pole, 415 V, 36 KA - 01 No (b) Phase indicating lamp with MCB - 1 set

Supply, install test and commissioning of automatic power factor (APFC) panel outdoor type for 50 KVAR 3 Phase, 440 volts 50 HZ with multistage correction (MPP-H capacitor) capacitors operate in 7 steps configration will be (4 x 5 KVAr & 3 x 10 KVAr) Preiwired with suitable size copper conductor cable all suitable for fairly balance load, factory made, front & back openable, CPRI approved fabricated out of 3.15 mm thick CRCA (Cold Rolled Closed Annealed Cell) sheet compartmentalized design including mild steel channel frame of ISMC 50 at the base of panel only for grouting purpose (fabrication shall be done in transpotable sections) and grouted with PCC using 20 mm graded stone aggregate, duly epoxy powder coated. Panel board/box shall be provided with danger notice plate with skull & bone sign, PVC gasket and sealed, making all incoming and out going electrical cable connections with new lugs, glands to be provided at cable entries, entire enclosure shall have a common copper earth bar of size 25mm x 5 mm at the rear with 2 nos earth studs, solid connection from main bus bar to swich gears with required size of al. bus bars and control wiring with minimum 2.5 sq. mm PVC insulated copper conductor single core , cable alleys, cable gland plates in two half etc complete as required and all as specified and as directed. Each panel shall be comprising of following accessories:- (APFC Panel) (a) 125 Amps 16 KA MCCB TPN 4 Pole 415 Volt - 1 Nos (Incomer) (b) CTs shall be provide for mesuring the capacitor corrent at incoming side of the panel

LT XLPE insulated armoured heavy duty cable 1100 volt grade ISI marked with alumimium conductor multi strand cross sectional area 630 Sqmm single Core complete all as specified and directed.

Material and labour for boring of hole under roads with mechanical arrangement upto 150 mm dia without disturbing the top surface of the road for passing the cable across the road complete all as specified and as directed.

Supply and fix Thermoplastic cable junction box for street lights of size 155 x 210 x 92 mm incl terminals for cable connection with IP 66 protection including one MCB single pole 6 Amp, 240 Volt, 10 KA 'C' curve mounted on DIN rail and connecting all the incoming and outgoing cable terminals with lugs all as specified and directed

M & L for security light energy saving & environmental friendly long life LED light made up of pressure Versatile die-cast aluminium housing with LED as lighting source of capacity 45W LED with IP – 66 incl bracket made out of GI pipe 32mm dia medium grade, 1.2mtr long bent to shape with MS flat iron clamps made out of 40mmX 6mm thick FIat, nuts, bolts complete all as specified and as directed

Material and labour for cable path indicator made out from cast iron and fixed on MS angle iron including PCC (1:3:6) 20 mm graded stone aggregate (size of PCC Block (0.3 m x 0.3 m x 0.3 m) buried in ground and path indicator top visible above ground duly marked “LT Cable” and painted with blue paint complete all as specified and directed.

Taking up cast iron sluice valve of 100mm bore complete all as specified and directed.

Taking up/dismantling of 100mm boreGI pipe complete all as specified and directed.

Dismantling and taking out of transformer of 100KVA capacity and including disconnecting of all electrical connections and same shall be deposit at E/M storeyard complete all as specified and as directed .

Material and Labour for sand filling around the cable with approved quality coarse and for sand cushioning for under ground cable including spreading and puning down desired thickness compete all as specified and as directed.

Materials and labour for brick protection cover to underground cables with sub class ‘B’ over burnt brick (locally available best quality), laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and as directed.

Material and Labour for laying liquid seal coat with 0.09 Cum of stone chipping 6.3 mm size mixed with 9.8 Kg of bituumen applied and rolled to a uniform surface with 8 to 10 tonne power roller complete all as specified.

Sheet metal enclosure DB VTPN 415 Volt 4 way double door type with 200 Amps rated bus bar for fixing MCCB as incomer and MCB as outgoing complete all as specified & directed..

S&F for DWCPE (SN8) 150 mm inner dia pipe including necessary connection & joints complete all as specified & directed.

S & F for 100 mm dia DI sluice valve both side flanged with SS spindle PN 1.0 with bolts, nuts, washer and rubber gasket complete all as specified & directed.

Bringing approved earth (as approved by Garrison Engineer) from sources outside defence land including all cost such as royalty if any, transportation, taxes etc. for area filling/ forming embankments including raising(any height from EGL)/lowering by approved earth and including raising earth spreading in layers not exc 30cm thick each layer, watering, compaction with 8 tonne to 12 tonne power roller and finished to required size and shape etc, any high/depth from EGL. Notes for : (i) Earth required for the item, shall be supplied by contractor, from out side MOD land of any lead, at his own arrangement. (ii) All cost of procurement of earth including cost of transportation, compaction, royalties, tax etc shall be deemed to be included in the unit rate quoted by the contractor. (iii) With reference to clause 3.6 of MES schedule Part-II on serial page No.21 it is clarified that measurement of the above item shall be of finished embankment/traverse of filled earth after consolidation/compaction and 5% deduction shall be made from measured and calculated volume to allow for increase in bulk.

Supply, installation testing and commissioning 315 KVA outdoor type transformer, energy effciency as per IS 1180:2014, Level 3, step down 11KV/433V, 3 Phase 50 C/S AC double wound, core type copper wound, oil immersed naturally cooled (ONAN) with external cooling tubes, delta/star connection on primary side (11KV) , and star connection on secondary side (433V) in accordance with vector symbol DYN-11 and having tapping at +/- 2.5%, +/- 5% and +/-7.5% to be changed by means of manually operated OFF LOAD tap changing gear. The rate of temperature rise after continuous fall load shall be all as specified in IS -2026. The transformer shall be complete with the following:- (a) Cable entry box for LT on secondary side for 3.5 core 400 Sqmm XLPE cable and HT 3 core 95 Sq mm on primary side including fixing arrangement as specified and directed by Engineer-in-charge. (b) Oil conservator with filling cap, drain valve and oil level gauge. (c) Dehydrating breather with connecting pipe, first fill of dehydrating agent and oil seal. (d) Explosion relief vent mounted on tank with double diaphragm and equiliser pipe connection to conservator air space (pressure release device). (e) Air relief plug. (f) Thermometer pocket.

ITEM NO 12.67 Cont.... (g) 100 mm dial type temperature indicator having range 0-120 degree C vapour pressure type with maximum reading pointer/Max temp indicator and resetting device with alarm/trip contact and additional contacts for switching ON or OFF the colling fans. (h) Two earthng terminals on tank and tank cover with lugs to suit 32 mm x 6mm GI strip. (j) Rating and diagram plate. (k) 100 mm dial type thermometer for winding temperature indicator having range 0 - 120 degree C vapour pressure type with maximum reading pointer/Max Temp indicator and resetting device with alarm/trip contact and additional contacts for switching ON or OFF to cooling fans. (l) Drain valve with threaded adopter. (m) Filter valve with threaded adopder (top and bottom). (n) Sample valve. (o) Inspection covers. (p) Lifting lugs. (q) Four plane rollers, bidirectional, hinged type at the bottom for shifting transformer from one place to another place.

ITEM NO 12.67 Cont.... (r) Top cover lifting eyes. (s) Extra bushing outside the cable box for providing independent earthing. (t) First fill of transformer oil. (u) Rail section and channel emdedded in foundation of suitable size in and including PCC platform of size 1.75m x 1.75m x 1.5m (PCC 1:3:6) including ramp as per manufacturers recommendations.

SCHEDULE 'A' PART-XIII (Provisional lumpsup) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

Lumpsum price worked out by the tenderer for Provisional sum of ` 4800000/- for following items including of earth work, concrete work, steel section etc. complete all as directed. (i) Basket Ball court : 02 Nos (ii) Lawn tennis court : 01 No (iii) Volley Ball Court : 02 Nos (iv) Football/Athletics/cricket ground : 01 No (v) Poly carbonated sheet roofing with steel truss over lounge as a dome shape only . (vi) Poly carbonated sheet roofing with steel truss over outdoor stage platform only. Note:- Contactor shall be quote, contractors percentage(amount) plus pre-prices amount.

M/s H.B Enterprises

M/s Singh enterprises

TRIBENI CONSTRUCTIONS LIMITED

Phoenix Infra

Sood Enterprises

M/s Jony Enterprises

M/S ALLIED CONSTRUCTION

MAA BHAGWATI ASSOCIATES

BHARAT ASSOCIATES PVT LTD

Bidder Name

BHARAT ASSOCIATES PVT LTD