construction of Lecture Room, faculty room, instrument room and shed and renovation of existing store and toilet in research area of Department of Agricultural Meteorology at CCSHAU Hisar. including PH and EI works

Amount

Civil work 1 to 75:- Earth work excavation in ordinary soil exclusive of compensation of earth- {HSR 6.2(b)} (b). earth-work undressed with a combined lead upto 15 metres including breaking of clods

Dressing of earthwork :-new work or remodelling work {HSR 6.3(i)}

Earth work in excavation in foundations, trenches, etc .in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches ,stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish lead upto 50 m and lift upto 1.5 m (a) soft/loose soil {HSR 6.25(a)}

Dismantling brick work, tile masonry or tile lining and tile terracing {HSR 8.5(b)} (b) in cement

Dismantling cement conglomerate/ terrazzo floors 25mm to 50mm thick including concrete base.{HSR 8.25)

Extra for smooth exposed concrete finish as desired which is not to be touched or plastered but is to be left as it comes out of the shuttering for columns (square or rectangular or polygonal in plan) (45% labour rate of item No.9.9)

Cement concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation and plinth.{HSR 10.28}

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.41)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59)

Pre-cast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete at the ground level or in first storey {HSR 10.77}

Pre-cast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in tiles and channels and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete at the ground level or in first storey. {HSR 10.78}

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. (HSR 10.81)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement , but including centring and shuttering, laid in position , complete in all respects (HSR 10.82)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams, girders, stairs, columns,(square or rectangular) battens and lintels etc., excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects (HSR 10.86)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in footings, strips, foundations, beams, rafts, pedestals and approach slabs of bridges etc., excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects,(For work upto 1.5 metres below ground level). {HSR 10.90}

Extra over item Nos. 10.79 to 10.94 , if 1:1.5:3 mix is used, instead of 1:2:4 {HSR 10.95(a)}

Damp proof course 40 mm thick of cement concrete 1:2:4 using stone aggregate with 2 coats of bitumen 20/30 penetration at 1.65 kg per sqm laid hot and sanded (HSR 10.114)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in pavements, roads, taxi-tracks and runways, laid to required slope and camber, including consolidation, finishing and tamping complete. (HSR 10.132)

First class brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR 11.7)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR 11.7+note) (i) at first floor

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure (HSR 11.48(a)

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure {HSR 11.48(a) +note} (i) at first floor

11.43 cm thick brick wall laid in cement stone dust (from crusher) mortar 1:4 without reinforcement in foundation and plinth. {HSR 11.52)

Providing 5.72 cm brick dalli facing with brick size 22.86 cm X 11.43 cm X 5.72 cm thick to be obtained after cutting of bricks laid in cement sand mortar 1:3 on RCC lintels, beams fascia etc. including centring and shuttering complete (HSR 11.98)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc.(HSR 13.13)

Top khurra 0.6 m X 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50)

Supplying and fixing in position G.I. pipe class ‘B’ spouts in chajjas and cantilevers {HSR 13.55(e)} (e) 50 mm internal dia, G.I. pipe

Bottom khurra on ground 1.2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR 13.57)

Cement concrete 1:2:4 gola 10 cm X 10 cm quadrant along junction of roof with parapet wall finished smooth, where specially specified (HSDR 13.64)

Providing and fixing PVC rain water pipe pressure of ISI mark in cement mortar during masonry work {HSR 13.89(a)} (a) 100 mm dia PVC pipe 6 kg. pressure

Providing and fixing PVC bend ISI mark {HSR 13.90(a)} (a) 100 mm dia PVC bend

Providing and fixing false ceiling with 12 mm thick Gypsum Board fixed on M.S. steel runners frame including cost of screws angles, cleats, rawel plugs with taping, filling with Gypsum compound and applying priming coat etc. complete in all respects (HSR 13.91)

Providing and fixing mineral fibre false ceilings tiles at all hieghts of size 595 x 595 mm of approved texture, design and pattern, the tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 85%, Thermal Conductivity K = 0.052 (-) 0.057 w/m k, Fire Performance as per (BS 476 pt - 6 & 7) in true horizontal level suspended on interlocking T-Grid of hot dipped all round gavanized iron section of 0.33 mm thick (galvanized @ 120 gsm) comprising of main T runners of 15 x 35 mm of length 3000 mm, cross T of size 600 x 600 mm suspended from celing using galvazied mild steel item (galvanizedd @ 80 gsm) 50 mm long 8 mm outerdiameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85 x 25 x 2 mm, spaced at 1200 mm centre to centre along main 'T'. The suystem should rest on periphery walls/partitions with the help of GI perimeter wall angle of wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all hieghts, The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-charge. with or without groves (HSR 13.92)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling (HSR 14.1)

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in flooring laid in any patterns as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles {HSR 14.89} Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in skirting / dado laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles {HSR 14.90} Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this. {HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92(b) (b) size of ceramic glazed tiles 300 mm x 450 mm

12 mm thick cement plaster 1:4 on walls (HSR 15.5)

12 mm thick cement plaster 1:6 on walls (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12)

10 mm thick cement plaster 1:4 on underside of ceiling (HSR 15.52)

Cement pointing 1:2 deep variety on brick and tile work (HSR 15.60)

Cement pointing 1:2 flush on flat brick flooring (HSR 15.71)

Cement pointing on stone slab pavement with cement mortar 1:2 (HSR 15.73)

20 mm thick cement plaster damp proof course 1:3 with 2 coats of bitumen at 1.65 kg per sqm laid hot and sanded :- (HSR 15.77(a) (c) vertical

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead , linseed oil, varnish and chalk mitti including finishing the surface to required finish complete (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade (HSR 16.3)

Applying priming coat with metal primer on new steel or iron work including preparation of surface {HSR 16.9}

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

White washing three coats (HSR 16.48)

Distempering with washable oil bound distemper (of approved manufacture) two coasts excluding priming coat on new work (HSR 16.57)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79(b) (b) 1st quality

Providing and applying two coats of white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc., complete (J.K/ Birla make). (HSR 16.81)

Commercial hard wood such as hollock, champ, chikrassy and chaplash ,etc.,(non coniferous timber other than teak conforming to I.S. specification No. 1003 kiln seasoned), shutters with vertical styles and rails, as specified in the statement No.1 ( attached in the end of this chapter) , with two Nos. plywood panels of the specified thickness, mentioned below , tongued and grooved including the cost of iron hinges, screws, chocks/cleats, stops ,etc. ,complete fixed in position excluding the cost of tower bolts and handles but including the labour for fixing the same- {HSR 17.30+note) (a) 35 mm thick (12 mm thick BWR Grade-II ply wood panel) Note: Nothing shall be paid extra for additional vertical style (any size) if required by the Architect or by the Engineer-in-Charge)

Proving and fixing 35 mm thick glazed door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. ( non-coniferous timber other than teak confirming to I.S. specifications No. 1003 kiln seasoned), with vertical styles and rails, as specified in the statement no.1 ( attached in the end of this chapter), with glass panes of 4 mm thickness , tongued and grooved including the cost of iron hinges , screws, chocks/cleats, stops , etc., complete fixed in position excluding the cost of tower bolt and handles but including the labour for fixing the same (Based on 17.30 (a) + 17.24(c)} (a) 35 mm thick ( 4 mm thick glass panes)

Providing and fixing sliding bolt with nuts and screws, etc., complete- {HSR 17.83(b)(ii)} (b) aluminium (ii) size 250 mm X 16 mm

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges :- {HSR 17.93(a)} (i) 25 mm thick

(iii) 35 mm thick

Structure steel work in angles, tees and flats, welded including cutting fixing all gusset plates, bolts, nuts, welding rod, etc. with hoisting and creating in position:- For roof trusses, well kerbs, plates and trussed girders, etc., of any span for buildings and bridges. {HSR 18.7}

Wrought iron and mild steel (using angles, flats square bars. tees and channels) ladders, grills, gratting frames, window guards, iron door openable or fixed stair case or parapet or any other type of railing , gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position {HSR 18.12}

Supplying, hoisting and placing in position tubular trusses including runners, purlins, consisting of steel tubes conforming to I.S. specifications of tested quality duly welded with fillet welds 6 mm thick through-out including wind bracing. Open end of pipe sealed with 3 mm thick plate including the cost of nuts and bolts where bolts connections are specified at flange joints including one coat of ready mixed red oxide zink cromate primer of approved quality assembling and fixed in position complete in all respect (HSR 18.14)

Fe-500 D TMT steel bars for R.C.C., works, where not included in the complete rate of R.C.C. , including bending ,binding and placing in position complete (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make {HSR 18.30(b)} (b) glass panes 4 mm thick, exceeding 40 sq dm areas

Pressed steel sheet frames (chowkhats), consisting of 2.00 mm thick steel sheet of the specified section, including iron lugs (hold fasts, iron hinges, confirming to PWD specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red led non-setting primer of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs, complete:- {HSR 18.34(a)} (a.) door and window frame of size 89mmx 50mm with 40mm wide single rebate.

M.S. Angle iron nozing of specified section including cutting to size, welding of M.S. bars for embedding in flooring and steps etc., fixed in position.(HSR 18.39)

Providing and fixing readymade white writing board of size 8'-0" x 4'-0" of PRESKO make with delux frame or any other similar brand, fixed in position, including wooden gutties, nails and screws, etc., complete in all respects as per drawing and design.(NS)

Providing and fixing marble strips of size 14mm to 17 mm and 125 mm wide in cement concrete flooring/pavement fixed in position, complete in all respects as per drawing and design or as directed by Engineer-in-Charge. (NS)

Providing and fixing IRC fabric of size 50 X 25 mm, made of 2.70 mm to 3.25 mm diameter wire, in steel frame with 3 mm thick flat iron cover moulding of 12.5 mm width fixed with machine screws, welded, complete in all respects as per architectural drawing & design. (excluding steel frame which shall be paid separately in HSR items) (NS)

Providing and fixing 0.60 mm thick high strength galvanized colour coated steel sheets having trapezoidal profiles of approved make (I.S.I. mark) in roofing, at all height, fixed in position with self drilling screws of approved shape & make, complete in all respects as per drawing & manufacture’s specifications and instruction of Engineer-in-Charge. (NS)

Earth filling under floors with dune sand (tiba sand), brought from outside (any lead), in 15 cm layer including laying, dressing, watering ramming, consolidating, excavation, carriage, loading, unloading and compensation, etc., complete (NS)

Providing and fixing 15 mm to 18 mm thick Z-Black granite stone (polished) on worktop laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade including rubbing and polishing, complete. (NS)

PH work 76 to 170 :- Earth work in excavation in foundation, trenches, etc., in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal soil, as directed within a lead of 30 metres. (HSR 6.6)

Excavation for pipe lines running under pressure in trenches and pits, in open areas, where disposal of surplus earth is done alongwith the alignment including trimming & dressing sides, leveling of beds of trenches to correct grade, cutting joint holes, cutting trees and bushes, etc., refilling consolidation and watering of refill, in 15 cm layers and restoration of unmetalled or unpaved surface to its original condition, including the cost of dewatering of rain water, diversion of traffic, night signals, fixing caution boards, watching, fencing etc., and outside the town in ordinary soil:- (HSR 6.8[a]) (a) without timbering and shoring up 1.5 metres depth

Excavation of trenches in streets, lanes or in open areas for storm sewer, sewers running by gravity and manholes to full depths as shown in drawing including shoring, timbering of poling boards, frame system type, dressing to correct sections and dimension, according to templates and levels, dewatering, provision for diversion of traffic, cutting trees and bushes, etc., night signals, profiles, pegs, sight rails, boning rods, crossing over trenches, for access to the houses, watching, fencing, etc., fixing and maintenance of caution boards, refilling of trenches, watering of refill, in 15 cm layers, ramming and restoration of unmetalled or unpaved surface to original condition and removal of surplus soil, from site of work, up to a lead of 1 K.M. in ordinary soil {HSR 6.10(a)} (a) for depth of excavation not exceeding 3 metres below ground level

Dismantling cement conglomerate/terrazzo floors 25 mm to 50 mm thick including concrete base. (HSR 8.25)

Scraping {HSR 8.32 (c )} (c) Cement plater

Cement concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation and plinth. (HSR 10.28)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR 10.41)

Cement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement , but including centring and shuttering, laid in position , complete in all respects (HSR 10.82) (at first floor)

Extra over item Nos. 10.79 to 10.94 , if 1:1.5:3 mix is used, instead of 1:2:4 {HSR 10.95(a)}

First class brick work laid in cement sand mortar 1:5 in foundation and plinth. (HSR 11.3)

First class brick work laid in cement sand mortar 1:5 in first storey up to 4 metres above plinth level. (HSR 11.8)

11.43 cm thick brick wall laid in cement sand mortar 1:4 without reinforcement , in foundation and plinth (HSR 11.47)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Conglomerate floor 50 mm thick in 2 coats, under layer 40 mm thick of cement concrete 1:2:4 and top layer 10 mm thick 1:1.5 cement grit ( 1 Part of cement : 1.5 part of stone grit).(based on HSR 14.10)

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles (HSR 14.91) Note : tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT, JOHNSONS & RAK

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92) (b) size of ceramic glazed tiles 300 mm x 450 mm (i) first floor

12 mm thick cement plaster 1:5 (HSR 15.6)

Cement rendering on plaster 1 mm thick. (HSR 15.75)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade (HSR 16.3)

White washing two coats (HSR 16.47)

Steel work, fixed independently without connecting plates, including cutting hoisting and fixing in position in:- {HSR 18.1(a)} (a) R.S. Joist

Fe-500 D TMT steel bars for R.C.C., works, where not included in the complete rate of R.C.C. , including bending ,binding and placing in position complete (HSR 18.22)

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets elbows etc. inside building and testing etc. complete including cutting threading. {HSR 28.18(b)} INCLUDING COST OF SPECIALS (i) 15 mm internal diameter of pipe line

(ii) 20 mm internal diameter of pipe line

(iii) 25 mm internal diameter of pipe line

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets, elbows etc. in trenches in the ground, cutting, threading and testing etc., complete. {HSR 28.19} (c) 25 mm internal diameter of pipe line

(e) 40 mm internal diameter of pipe line

(h) 80 mm internal diameter of pipe line

(i) 100 mm internal diameter of pipe line

Extra for fixing and jointing union couplings in G.I and W.I pipe lines. {HSR 28.21} (b) 20 mm internal diameter

(c) 25 mm internal diameter

(e) 40 mm internal diameter

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. (HSR 28.24) (a) 11.43 cm thickness of walls

(b) 22.86 cm thickness of walls

Cutting holes up to 23 cm square for pipes in floor and roofs of cement concrete reinforced concrete or reinforced brick work and making good including repointing, replastering, replacing bitumen and colour or white washing where required. {HSR 28.26(b)} (b) 115 mm thickness of roof of floor

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I pipelines laid in the ground or inside buildings including cartage from divisional stores or nearest railway station to site of works. {HSR 28.29} (c) 25 mm internal diameter

(e) 40 mm internal diameter

Making connection with the existing G.I branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site. (HSR 28.34)

Providing and fixing ductile iron seal manhole covers and framers of 610 mm x 610 mm with looking arrangements on clear water tanks including cost of setting in Cement concrete 1:2:4 correct alignment and levels including carriage, loading etc. complete in all respects to the satisfaction of Engineer-in-Charge. (HSR 28.59)

Providing and fixing steel bar embedded plastic steps of size 263 mm x 165 mm of orange colour, conforming to specifications, in pump chambers, manholes etc., having minimum 3 mm thick polypropylene on 12 mm dia ribbed steel bars per IS : 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1:2:4 cement concrete including carriage, loading, unloading, stacking, handling, re-handling etc., complete in all respects to the satisfaction of Engineer-in-Charge. (HSR 29.28) (Amended item)

Constructing brick masonry inspection chambers sizes as given below up to 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar2:3 in foundation cement concrete 1:2:4 benching 12 mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2:4 slab 100 mm thick/C.C. topping. 50 mm thick with 455 mm x 455 mm/ 455 mm x 610 mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design. {HSR 29.84(c)} (c) size 600 mm x 900 mm inside ( with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg. With R.C.C. slab)

Providing slat glazed stone ware pipes grade ‘A’ in standard length of 600 mm each pipe marked with is: 651 and their lowering, cutting, jointing and testing as desired in HSR item No. 29.38, 29.39, 29.40, including the cost of jointing materials as well as carriage, loading, unlloding stacking, handing, re-handling etc. complete in all respects to the satisfaction of Engineer-In Charge. (HSR 29.95) 150 mm internal dia

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type Orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100 mm H.C.I ‘P’ trap with or without vent as required and all other necessary fittings as fully described in item no. 30.1 above (excluding cost of CI high level flushing cistern) (based on HSR 30.2) (a) 580 mm (i) WHITE

Providing and fixing in position best Indian make European type water closet suite with concealed ‘P’ of ‘S’ trap with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item No. 30.3 above (excluding cost of C.I. high level cistern) White based on {HSR 30.6 (a) (i)}

Extra over item no. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13) (i) White plastic seat ( Solid)

Extra for providing and fixing 32 mm dia. G.I/ C.P flush pipe complete with accessories instead of 32 mm dia. Galvanised telescopic flush pipe with clips ( as required by the Engineer-in-charge) {HSR 30.15(b)} (b) 32mm dia C.P brass flush pipe

Providing and fixing in position best Indian make large flat back or angular lipped front urinal 610 mm high consisting of:- (HSR 30.25) (i) flat back lipped or angular urinal basin or vitreous china-ware; (to the approval of the Engineer-in-charge) (ii) 5 lit capacity mosquito proof Indian make C.I automatic flushing cistern painted with non-yellowing white enamel paint or other approved shade enamel paint on out side and superior black bitumastic paint on inside with screwed 15 mm pipe: (iii) pair of R.S or C.I painted brackets and brass couplings:- (iv) pair of C.I special type brackets for urinal: (v) 32 mm C.P brass spreader: (vi) standard size G.I flush pipe with C.P brass wall clips and unions: (vii) 32 mm C.P brass waste with dome-grating: (viii) 32 mm C.P brass bottle trap: complete including cutting and making good the walls and floors and painting of fittings etc. (as required by the Engineer-in-charge) Single Urinal (i) White

Extra for providing and fixing vitreous automatic flushing Cistern including fittings and brackets of C.I. flushing cistern complete {HSR 30.37(a)} (a)5 ltr. capacity cistern (i) white

Extra for providing and fixing standard size C.P. brass flush pipe complete with fittings instead of G.I flush pipe complete {HSR 30.38(a)} (i) For single urinal

Providing and fixing in position best Indian make (ordinary) lavatory suites consisting of Lavatory in vitreous china ware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary, R.S or C.I brackets for building into wall including painting;32 mm C.P. brass waste with C.P brass chain and rubber plug;15 mm C.P brass screw down pillar tap with jamnuts or couplings best design ( as approved by the Engineer-in-charge) all fittings best Indian make and; to the approval of the Engineer-in-chargeall brass work chromium plated and complete in all respects including cutting and making good the walls and floors and painting of fittings etc. (HSR 30.41) (iv) size 550 mm x400 mm with one no tap

Providing and fixing in position 32 mm dia G.I waste pipe embedded in wall or lead waste pipe (weighing 3.47 kg per meter and 2.8 mm thick) up to floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge) (HSR 30.48)

Providing and fixing in position best Indian make chromium plated brass bottle trap 32 mm diameter (HSR 30.50)

Providing and fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P brass screws ( as required by the Engineer-in-charge) complete including cutting and making good the walls etc.{HSR 30.71(a)(i)} (a) INDIAN MAKE (i) 600mmx450mm

Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P brass screws and rawl plugs etc. complete including cutting and making good the walls etc. {HSR 30.73(a)(ii)} (a) C.P. BRASS (ii) two way

Providing and fixing in position 15 mm i/d C.P brass bib cocks of best quality ( as required by the Engineer-in-charge) {HSR 30.75 (c)} (c) bib cock

Providing and fixing in position C.P brass stop cock (as approved by the Engineer-in-charge) {HSR 30.76 (a)} (ii) concealed stop cock with flange

Providing and fixing in position best Indian make C.P brass inlet connection 15mm with 375mm pipe and C.P brass nuts. (HSR 30.83)

Providing and fixing in position H.C.I soil waste vent or antisyphonage pipes to I.S.I specifications of E.L.C manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floors etc. and making good to its original condition but excluding cost of lead jointing. {HSR 30.84(b)} (b)75 mm i/d

Cutting chase in brick walls in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition {HSR 30.95(a)} (a) size 75 mm X 75 mm

Providing and fixing in position automatic brass ball valves in tanks {HSR 30.110(b)(iii)} (b) WITH PLASTIC BALL (iii) 25 mm internal diameter

Providing and fixing HDPE WATER STORAGE TANKS of sintex, diplas O.K. Supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (HSR 30.119) 500 Ltr. Capacity

Main Switch Supply and erection of metal clad switches/ B.D.B.S. with rag bolts on wall or on existing angle iron board/ pedestal including bonding to earth and necessary connections :- (HSR 31.12(a)(xiv) (xiv) Triple pole switch with neutral link 63 amp. 415 volts .

Earthing. (HSR 31.22[i]) (i) Earthing with G.I. earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. as required

(xii) Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required

Supply and erection of Godrej Almirah type M.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars. The top covering should have downward overhang of 75 mm on all sides of pedestal, having two sets of water proof ventilation holes of suitable size on the sides, at top and bottom, each set containing four Nos. holes to discharge the heat produced by the current. The shutters fixed with rubber gasket of superior quality and of suitable size of make it water proof. The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and it’s legs are embeded upto the entire depth in 1:2:4 cement concrete block, projected 75 mm all around the pedestal and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of work-(HSR 31.33(iii) (iii) M.S. pedestal of size 750 mm wide, 1200 mm high and 300 mm deep and bottom totally open, duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster, having a base of size 1050 mm x 600 mm x 250 mm below ground level.

Supplying & jointing three core flat cables of Finolex, Polycab, Ecao & Bunton with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors with voltage grade 1100 volts marked with IS:694:1990 including cost of jointing materials as well as carriage, loading, unloading etc., complete in all respects to the satisfaction of Engineer-in-Charge. (HSR 31.59) 2.5 square mm (copper)

Supply of GI pipe 'B' Class ISI Marked Ravindra/Jindal/Parkash(Surya) Make. (NS) (i)15 mm i/d

(ii)20 mm i/d

(iii)25 mm i/d

(iv)40 mm i/d

Supply of GI Union Couplings of UNIK/UNCO make . (NS) (i) 20 mm i/d

(ii)25 mm i/d

(iii)40 mm i/d

Supply of Gun Metal Peet Valve ISI Marked of DRP/Leader/Bajaj make (NS) (a) 25 mm i/d

(b) 40 mm i/d

Providing and fixing in position PVC flushing cistern 8.0 ltrs. capacity of Hindware/Perryware/Cera make ISI marked, white, alongwith fittings complete in all respect. (NS)

Supply and fixing of CP brass Jet with flexible pipe and patti etc. of best quality, complete in all respect (excluding cost of CP brass cocealed stop cock (NS)

Supply of PVC pipe 6 kg/cm² pressure of ISI marked of Prince / Supreme/Skipper make (NS) a) 90mm o/dia (3” i/dia) size

b) 110mm o/dia (3” i/dia) size

Providing and fixing PVC floor traps of 3" i/d outlet of Prince/Supreme/Skipper make complete in all respect. (NS)

Providing and fixing PVC Gully traps of 4" i/d size with cover and frame of Prince/Supreme/Skipper make complete in all respect. (NS)

Boring of well 6" dia size upto 150 feet deep (suitable for lowering 5" dia PVC pipe) with suitable boring system complete in all respect as per directions of the Engineer-in-Charge.(NS)

Providing,lowering,joinging and fixing PVC blind pipe 5" i/dia 6kg/cm2 pressure in the bore hole complete inall respect. Make Prince/Supreme/Skipper make (as approved by the Engineer-in-Charge). (NS).

Providing,lowering,joinging and fixing PVC perforated/slotted pipe 5" i/dia 6kg/cm2 pressure along with nylon jali and dhaga etc. duly wrapped on the PVC pipe (for making filter) in the bore hole complete in all respect. Make Prince/Supreme/Skipper make (as approved by the Engineer-in-Charge). (NS).

Providing and fixing in position PVC End Cap for 5" i/dia PVC pipe complete in all respects of Prince/Supreme/Skipper Make. (NS)

Providing and fixing in position MS clamps (heavy duty) of best quality complete in all respects. (NS) (a) For 5" i/d PVC pipe

(b) For 1½" i/d GI pipe

Development of tubewell bore for at least 12 hrs.(or till development of cavity) with suitable system/engine etc. complete in all respect to the satisfection of the Enginer-in-charge.

Providing and fixing in position submersible pumping set 2.0 HP capacity with 1½" dia delivery, single phase of Kirloskar/KSB make, complete in all respects as approved by the Engineer-in-charge. (NS)

Providing and fixing in position volt metre of 0-500 volts of L&T/ Havells make complete in all respect.(NS)

Providing and fixing in position ampere metre of 0-50 ampere of L&T/ Havells make complete in all respect.(NS)

Providing and installing split type air conditioners, five star rating inverter type with copper coils 2.0 ton capacity ± 10%) fitted with super tropical - DC PAM inverter- return cooled - rotary compressor operating on refrigerant R-410-A suitable for wall mounting confirming to IS : 1391 (part-2)/92 (except power consumption norms) with upto date amendments, suitable for operating on 230 volts, 50 Hz single phase A.C. supply having following specifications:- (i) Cooling coil row -3 Nos. (ii) Air flow (CMH) -1450 cum/ hr. (iii) Sound level (H/M/L)- 41/38/34/25(silent mode) (iv) Louvers swing- 3D + 3D Auto etc. complete in all respect MAKE :- O General/Toshiba/Mitsubishi (Heavy Industries) (five star rating) Model as approved by the Engineer-in-Charge

Providing and installation of automatic voltage stabilizer of 5.00 KVA capacity (heavy duty) copper wound 100 up voltatge ofV-Guard make ISI marked complete in all respect. (N.S.)

Providing and fixing extra copper tubing/regrigerent pipe for above split air conditioners (if required) consisting of inlet, outlet pipes, insulation and electric wiring etc. as per requirement, complete in all respect beyond 4.0 metres length. (NS) NOTES :- INSTALLATION OF AIR CONDITIONERS INCLUDES:- 1. Mounting/ fitting indoor and outdoor units at their respective locations 2. Providing & laying refrigerant pipe line of four metres length and beyond (if required) and connecting both the units after drilling holes in the wall, if required. Thickness of the copper tubing shall not less than 0.80 mm. 3. Insulating the suction pipe with expanded polythene pipe tubing. 4. Providing & laying drain pipe to throughout the condensate water being formed in the indoor unit 5. Leak testing entire system 6. Charging refrigerant gas in the unit 7. Electric wiring ; suitable electric wiring and switch should be provided with in 4 metres of the location of the units as per requirement 8. PVC channels for concealing the pipes etc. 9. Refrigerant piping thickness- 18 guage (1 mm) (i) Liquid line :- 6.35mm (1/4") (ii) Gas line:- 15.88mm(5/8") 10. Providing and fixing 2.5 sqmm x 4 core coper wire sheathed for connections and communication between indore unit to outdoor unit. (NS)

Providing and fixing in position powder coated MS stands for outdoor units of air conditioners including suitable nuts & bolts etc. of best quality complete in all respect (NS)

EI work 717 to 204:- MINIATURE CIRCUIT BREAKER AND ISOLATOR:(HSR 31.17) Supply and erection of miniature circuit breaker/isolator 240/415 V in the existing distribution board including making necessary connections (a) Miniature Circuit Breakers of 9 K.A. breaking capacity (ii)6-32 amp. SP MCB

(ii) 32 amp. TPN MCB

S/E of fittings and accessories (HSR31.18) (xxvi) Supply and erection of hexagonal M.S. box 1.60mm thick having each side 8cms, 7.5cms deep, top covered with M.S. lid by means of screws including 10mm dia 30cm long mild steel rod made into suitable suspension hook and erected in R.C.C. slab for erection of fan, the bottom covered with 3mm thick bakelite sheet with suitable holes, painting etc. compelte with all labour and material required to complete the job

PIPE LAYING: Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required :-(HSR 31.21) (xv) Heavy gauge welded conduit pipe 20 mm dia 1.60 mm thickness on surface

(xvi) Heavy gauge welded conduit pipe 25 mm dia 1.60 mm thickness on surface

(xxi) Heavy gauge welded conduit pipe 20 mm dia 1.60 mm thickness on flushed

(xxii) Heavy gauge welded conduit pipe 25 mm dia 1.60 mm thickness on flushed

EARTHING (HSR 31.22) (i) Earthing with G.I. earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. as required

(v) Extra for charcoal or coke and salt for G.I. plate earth electrode.

(xii) Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15mm dia G.I. pipe from earth electrode as required.

Miscellaneous (HSR 31.35) (i) Supply of M.S. Pipe (B-Class) for suspension rod of ceiling fan including threading if required. (a) 15mm dia

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe (HSR 31.40) (i) Size 1.5 sqmm(3/0.81mm)

(ii) Size 2.5 sqmm(3/1.05mm)

(iii)Size 4 sqmm(7/0.85mm)

S/E of PVC conduit pipe ISI marked (Medium) recessed in wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work (HSR 31.44) (a) 20mm dia

S/E of copper lugs including crimping etc. upto the entire satisfaction of Engineer-in-Charge of work (HSR 31.45) (b) 4 sqmm to 6 sqmm

(c) 10 sqmm

Pdg. and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (HSR 31.56) 10 amp. 1 way switch

20 amp.switch

10 amp. Socket

16 amp. socket

Fan regulator

Blinking plate

Pdg. and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (HSR 31.57) 1 &2 Modules

3 Modules

6 Modules

8 Modules

12 Modules

Supply, installation testing and commissioning of wall/free standing floor mounting dust & vermin proof compartmentalized cubical panel made out of 2mm thick CRCA sheet, required hardware 3mm thick Bakelite sheet provided all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 coat of Zinc/Red oxide primer followed by 2 coats of powder coating in grey or required shade after rinsing. The panel having PU/Neoprene rubber gasket of not less than 3mm thickness separate detachable gland plate MS base channel hinged door with inter locking arrangement for equipment/switch wear. Transparent acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar Bakelite sheet 3mm thick for separately cable alley to BBC from switch chamber extended solid copper bars upto cable alleys shall provided for outgoing connection which shall be paid as extra items. Side walls and cable alley compartments shall be having bolted type doors with detachable extension type structure. The panel will be complete with control wiring (copper) and fuse protection (Only outer area on all sides shall be measured) (HSR 31.63)

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod and regulator etc. wih rating 5 star {NS} i) 1200mm sweep. Make: Usha, Orient, Crompton.

S/E of recessed type 42 Watt full window glare free opal diffuse LED Panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 4600 or above in cool day light (5600K to 6500K), Power factor >0.95, CRI (Ra) >80, LED Lamp efficiency ≥ 140 lm/w, Average life > 50000 hours, complete with all accessories as required with connections (Industrial) Make: Philips, Havells, Wipro, Bajaj. (NS)

S/I/T/C of push ON/OFF type 25 A modular type motor starter switch (white color) for AC's including the cost of petty material required to compete the job upto entire satisfaction of Engineer-in-charge. (NS) Make;- Schneider/Crabtree/Athena

Supply of propeller type AC ventilating fan (exhaust fan) with necessary earthing arrangements of fan with shutter complete in all respects Size 300mm(12”) sweep Make: Orient, Usha, Havells. (NS)

S/E of LED tube rod ≤20 watt double side connections with 4 feet long housing made of CRCA sheet steel, epoxy powder coated white after phosphochromate treatment and 2 Nos. lamps push fit type white polycarbonate holders and reflector made of white powder coated CRCA sheet. Total system lumen of 20 watt LED should be ≥2200 or above in cool day light (5700K to 6500K), Power factor >0.95, CRI >80, Average life ≥50000 hours, complete with mounting bracket and accessories as required with connections. Make: Philips, Havells, Wipro, Bajaj. (NS)

Kamal Sharma Contector