SPECIAL REPAIR TO BLDG NO. P-27 SINGLE LIVING NURSING OFFICERS ACCN AND BLDG NO. P-27/A AND P-27A1 NURSING OFFICERS MESS OF MH JABALPUR UNDER GE (WEST) JABALPUR

Amount

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc including removal of debrise to a distance 50 m out side MD land complete all as specified & directed.

M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in chajja, parapet, facia etc and the like complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

Use and waste of form work to faces of walls,lintel band, retaining walls , abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter, surface fair finished complete all as specified and directed.

Use and waste of form work to chajjas and similar items including edges etc. complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in filling pressed steel door frame without using extra cement complete all as specified and directed.

Supplying and fixing 40mm thick flush shutters of make as approved by GE, solid core construction, with block board core and plywood face panels, both face covered with decorative face veneers with lipping/frame to match complete all as specified & directed.

Supplying and fixing in repair 19 mm thick water proof block board of exterior grade-1 fixed with screw as kitchen, cup board box and shutter & shelves etc complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in frame complete all as specified & directed.

Supply & fix factory made solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, at site complete all as specified & directed.

S&F in repair 18 mm thick PVC sheet celuka board for kitchen cabinet including necessary fitting & fixture as per manufactures instructions complete all as specified & directed.

S&F in repair stainless steel hinges of 75 mm for cupboard including necessary fitting & fixture as per manufactures instructions complete all as specified & directed.

S&F Europa cupboard lock complete all as specified & directed.

S&F stainless steel handle 150 mm including all connection fitting complete all as specified & directed.

Supplying & fixing 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supplying & fixing 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

M&L for 5 to 10 mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5 Cm complete all as specified & directed.

M&L for 11 to 15 mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 5 Cm but not exc. 10 cm complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in framed work complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in section, in unframed work in any position complete all as specified and directed.

S&F suspended false ceiling grid system using chicago metallic (E Grid) exposed suspended system, grid size 600 x 600 mm comprising of GI powder coated main runner 39 x 24 x 0.8 mm (Thickness comprising of GI/0.4mm + PPPCGS/0.3mm and min weight of runner 1.35 Kg for 3600mm length), cross tee 29 x 24 x 0.80mm (Thickness comprising of GI/0.4 mm + PPPCGS/0.3mm and min weight of angle 0.195 Kg for 600mm length) and wall angle 22.2 x 22.2 x 0.65 mm thick (Thickness comprising of GI/0.35mm + PPPCGS/0.3mm and min weight of angle 0.7 Kg for 3050mm length) with and including 4mm thick HPSC (High Pressure Steam Cured) pre-primed, self embosed, textured design board, water resistant, termite resistant, fire resistant for insulation and acoustic purpose to be placed in grid system duly suspended with @ 1.2m c/c both way with 4 mm dia GI wire hangar fixed with steel dash fasteners or from purlin of roof with butterfly clips (wt 0.007kg), hold down clips (wt 0.0035kg) etc complete, ( main runner / cross tee /wall angle of Galvanised Iron powder coated), as per manufacturere instruction complete all as specified and directed. Note : Cost of making frame work and board (cut out) for fixing light fitting grill diffuser etc shall be deemed included in the quoted rate.

Supply and fix extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified & directed.

Supply and fix extruded aluminium alloy handles, fabricated type, anodised of size 125 mm complete all as specified & directed.

Supplying & fixing 100mm size butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized, type B-21 complete all as specified & directed.

Supplying & fixing continuous (Piano) hinges, mild steel, bright finish or electro galvanized, 30 mm width of flaps (when open) complete all as specified & directed.

Supplying & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified & directed.

Supplying & fixing 300 mm size ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified & directed.

Supply and fix 125 mm aluminium anodised hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

S&F aluminium Hat & coat pegs, solid body, 125mm to 175 mm fixed with brass screw complete all as specified & directed.

S&F in repair of stainless steel peg set of 6 powder coated complete all as specified and directed.

S&F mild steel drapery rod/ curtain rod of 25mm dia fancy type with PVC coating and fixed in the MS hook or brackets in both side complete all as specified and directed.

M&L for Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treating with tar or coal tar black paint small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each complete all as specified and directed.

Supplying & fixing 300 mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Cutting chases in brick walls, pinning in brick wall/ stone concrete block or slab walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good as per existing, cutting not exceeding 10cm girth complete all as specified and directed.

M&L for mild steel work conforming to Fe-290 Gde -165 as in hand rail, half round or other steel section or core for wooden hand rail strait portion, drilled and countersunk for balusters running bars for doors, nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

Supply only stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples or any other means as per site requirement complete all as specified & directed. Note:- To be fixed in steel windows/ ventilators since fixing element of this item has already been considered alongwith steel windows/ ventilators as taken here-in-before.

Supply and fix rolled mild steel sections conforming to Fe- 410-W (Gde E-250) quality-A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates etc complete all as specified & directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified & directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed..

Dismantling of mangalore pattern roofing tiles with ceiling tiles or state roofing bedded in lime or cement mortar in roof covering complete all as specified and as directed.

Dismantting of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering and ridge complete all as specified and as directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based 0.50mm thick (AZ-150) corrugated steel sheet of any colour having minimum tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts as complete all as specified & directed.

S&F of pre-painted galvalume aluminium zinc coating GI based 0.50mm thick (AZ-150) plain steel sheet of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) fixed with self tapping screws complete all as specified & directed.

M&L for glazed ceramic coloured tiles 350x250x7mm or 450x350x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement forming joints to full depth at every 3M intervals and at every change of direction and filing with bitumen sand mixture 1:3 by weight complete all as specified and directed.

M&L for scratch free light shade vitrified floor tiles, minimum 10mm thick (square/ rectangular) area of each tile exc 0.42Sqm but not exc 1.00Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for scratch free light shade vitrified floor tiles, minimum 10mm thick (square/ rectangular) area of each tile exc 1.42Sqm but not exc 1.00Sqm as in skirting/ dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for 18-20mm thick granite of approved quality as in platform i.e. in horizontal & vertical position, machine cut (table rubbed and polished) laid over and including 15mm thick rendering in CM 1:4 and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed.

M&L for machine cut cudappah stone slab flooring 20-25 mm thick as in shelve for cooking platform complete all as specified and as directed.

M&L for machine cut kota stone slab as in flooring, 18-20mm thick over & including 20mm thick cement screed bed in CM (1:6) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for machine cut kota stone slab as in skirting/ vertical surface, 15-18mm thick over & including 10mm thick rendering in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for rounding to edges of granite stone slabs one edge, such as in counter type WHB, cooking platform and other similar situations etc. complete all as specified and directed.

Taking down cement plaster etc on brick walls/ terrazo surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for 10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed. ( Note:- Liquid Water Proofing Compound shall be measured and paid for separately. )

M&L for preparation of newly plastered surfaces of wall and apply two coats of oil emulsion distemper over 3 mm thick of Birla/ JK wall care putty over a coat of cement primer for smooth finish of wall complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling finished even and smooth without using extra cement complete all specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash as in ceiling complete all as specified and directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' modular fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M&L for brick work with sub class B bricks, modular fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty /wooden beads in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

Supply only 3.0mm thick figured glass, pinhead type for glazing in squares n exc. 0.5 sqm in each pane complete all as specified and as directed. Note:- (i) To be fixed in wooden doors/ windows since fixing element of this item has already been considered alongwith wooden doors/ windows as taken here-in-before. (ii) Beads for glazing shall be supplied with joinery.

M&L for preparing old decorated plastered or unplastered surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spot and applying one coat of white wash on ceiling complete all as specified and as directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of new surfaces of iron/ steel of any description n.exc 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of old painted surface of wood and wooden based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with one coat of creosote oil complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and preparation of surfaces for further treatment and applying two coats of cement base paint over a coat of alkaline resistant primer on external wall plastered or unplastered surface complete all as specified and directed. ( Note :- Curing shall be done before and after applying of paint. )

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and preparation of surfaces for further treatment and applying two coats of oil bound distemper over 3 mm thick wall care putty on wall surface complete all as specified and directed.

M&L for prepration of new plastered surfaces of external walls and applying two coats of cement base paint over & including a coat of cement base primer complete all as specified & directed.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc including removal of debrise to a distance 50 m out side MD land complete all as specified & directed.

M&L for 10mm thick rendering over roof surfaces in CM 1:3 with using water proofing compound @ 3% by wt of cement or as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum over lap of 100mm and over lap shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer's as specified for polymeric water proofing membrane.

Supply only water proofing compound (liquid) ISI marked of make as approved by GE complete all as specified & directed.

Supplying & fixing for 125x60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified, supplied and fixed complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 20mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 25 to 32 mm bore of pipe complete all as specified and as directed.

Refixing old steel water tubing 15mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Refixing old steel water tubing 20mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Refixing old steel water tubing 25 to 32 mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning.

Supply & fix 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & fix 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & fix 25 mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply and fix in repairs, 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed.

S&F in repairs, 15mm dia bib cock,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed.

S&F in repair 15 mm bore brass chromium plated wall mixer, 3 in 1 system with hot and cold water arrangement with provision of both hand shower and overhead shower along with CP brass caps screwed for fixing complete all as specified and as directed.

S&F in repairs, sheet glass corner shelf consisting of 5.5mm thick sheet glass shelf 30 cm wide complete all as specified & directed.

S&F in repairs, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, design & make/ pattern as approved by GE complete all as specified & directed.

Supply & fix in repairs kitchen sink with drainage board made of stainless steel 1.0mm thick with plug, washers with and including 32 mm dia PVC rigid waste pipes and C.P coupling including fixing cantilever brackets of suitable shape & size as required at site and connecting unions to pipe, overall size 915 mm x 460mm, bowl size 410 mm x 330 mm x 160mm and necessary cutting to slab complete all as specified & directed.

S&F in repair kitchen plate rack made of stainless steel 1 mm thick complete size of 1200X900X 200 mm complete all as specified & directed.

Supply & fix in repairs vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F toilet paper holder of brass, chromium plated, fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

Supply & fix in repairs, soap dish disc wall mounted (oval) type, silver brass finish including all necessary screws of same finish of pattern & make as approved by GE complete all as specified and directed.

Supply & fix 32mm bore, low density polyethylene pipe (LDPE) pipes, of pressure rating 6 Kg/cm2, fixed to walls, ceilings or laid in floor fixed complete all as specified and directed.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed.

S&F in repairs grating doom 125 mm dia of PTMT (Minimum weight 25 gms) complete all as specified & directed.

S&F in repair, brass CP shower rose 200 x200 mm size suitable for 15mm bore GI pipe with or without swivel joint including fixing to pipe and union as approved by GE complete all as specified and directed.

S&F, in repair, PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size. complete all as specified and directed.

S&F chromium plated brass tubular towel rail, 20mm dia, D type, 60 cm long fixed with screw and wooden or plastic cleat complete all as specified and directed.

S & F, in repair, towel ring, brass chromium plated, round type, fixed with screws and wooden or plastic cleats complete all as specified and directed.

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but plastic water closet seat, black/ white, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified & directed.

M&L for 100 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair plastic water closet seat cover, coloured, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed..

M&L Waste fittings, brass, chromium plated for 32 mm dia of glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed..

M&L Waste fittings, brass, chromium plated for 40 mm dia of glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Supply and fix in repair 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed.

Taking down eaves gutter, rain water pipes of any size or pattern including all fittings etc complete all as specified and as directed.

Supply & fix in repairs, PVC (SWR) branch piece (double Y), equal or unequal, 110mm bore with access door rubber ring joint fixed to wall complete all as specified & directed.

Supply & fix in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 110 mm bore (spigot or socket type) or with parallel branches complete all as specified & directed.

Supply and fix 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints,fixed to wall or laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed.

Supply and fix 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supply and fix 110mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply and fix 75mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply & fix PVC (SWR) junction single (single T), equal or unequal provided with access door, 110mm bore complete all as specified & directed.

Supply & fix PVC (SWR) junction single (single T), equal or unequal provided with access door, 75 mm bore complete all as specified & directed.

Supply and fix 110mm bore PVC (SWR) vent cowl complete all as specified & directed.

S&F in repair PVC (SWR) gully trap, out let dia 125/110mm, plain with grating including jointing with solvent complete all as specified and as directed.

S & F stack clamps, out of 50mm by 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore etc complete all as specified and directed.

Dismantling of water tank of any description of capacity exc. 250 litres but not exc. 500 litres, removing to store or from the site complete all as specified and as directed.

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Supply & fix, 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed. (Note-Min weight should not be less than 210 gms)

Supply & fix 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply & fix 25 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified & directed.

Taking down of existing exhaust/ ceiling fan of any size/ sweep and depositing in the safe cosdoy of MES store complete all as specified & directed.

Taking down main switches/ DB's (alongwith existing board, MCBs & isolators) including removing the same from site and making good disturbed surfaces complete all as specified & directed.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified and directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/ regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one light /fan/exhaust/bell point controlled by one no one way switch 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with and including 01 number single pole MCB 20 Amps complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 1 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 2 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 3 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 4 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 6 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement of white modular cover plate with frame for modular switch 8 module as per existing make/model complete all as specified & directed.

Supply & fix in replacement modular metal flush box 1/2 module suitable for modular switch as existing switch box and making good to distube surface complete all as specified & directed.

Supply & fix in replacement modular metal flush box 3 module suitable for modular switch as existing switch box and making good to distube surface complete all as specified & directed.

Supply & fix in replacement modular metal flush box 4/5 module suitable for modular switch as existing switch box and making good to distube surface complete all as specified & directed.

Supply & fix in replacement modular metal flush box 6/8 module suitable for modular switch as existing switch box and making good to distube surface complete all as specified & directed.

Supply & fix in replacement of modular switch 06-10 Amp one module 230 volts AC complete all as specified and directed.

Supply & fix in replacement of modular switch 16 Amp one module 230 volts AC complete all as specified and directed.

Supply & fix in replacement of modular socket 6 Amp, 2/3 pin combined 2 module, 230 volt AC complete all as specified and directed.

Supply & fix in replacement of modular socket 6/16 Amp, 2/3 pin combined 2 module, 230 volt AC complete all as specified and directed.

Supply & fix in replacement of modular bell push switch piano ,flush type, 6 Amp complete all as specified and directed.

Supply & fix Buzzer, Ding Dong AC. 230 volts, single pole suitable for AC 230 volt single pole complete all as specified and directed.

Supply & fix ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply & fix in repairs, modular stepped type electronic fan regulator mini flush type 120/ 280 Volts, 02 module complete all as specified & directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 25 mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

Supply and fixing LED focus light (wall/floor mounted) decorative light 18 watt warm white 4000K (picture lights) with surge protection of 4 KV, IP protection and all fixing acceseries alongwith connecting it with 3 core 1.5 sqmm copper conductor to required tapping point all as per required and directed by Engr in charge.

S & F, in repair, Smart bright Batten Series, LED luminaire using LED 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LED and delivers consistent light output, stable color, start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

S & F, in repair, Bulk head endura LED light fitting complete with and including 10 watt LED lamp and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed.

S&F MCCB 4 pole, 415 V ,with thermal megnetic release, adjustable type 100 Amp with breaking capacity 16 KA including taking down old unserviceable MCCB of any type and capacity complete all as specified and as directed.

S&F, in replacement, sheet metal enclosure distribution boards IP-54 and IK-09 , double door factory made Vertical TPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus barand PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 100 amps and 12 modules circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed.

Supply and fix in repairs, 45 watt new generation energy saving and environmental friendly long life LED security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP66 protection and impact resistance of IK07 on bldg wall with and including pipe bracket made of G.I tubing 32/40 mm dia bore medium grade ISI marked 1.20m long bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/ MS clamps & 12mm dia bolts, nuts & washers etc including painting to all and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

S&F change over switch 4 pole 200 Amp, 415 Volts, Onload type, front handle type with enclosure including connection and testing complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure MCB DB double door (Acrylic) single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection, complete all as specified & directed.

Supply & fix MCB SPN, 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix MCB SP, 6 to 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 50 sqmm, 3.5 core including jointing materials such as cable glands & lugs etc after taking out the old unserviceable cable and testing on completion complete all as directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe,post, stay, cable etc or n. exc.10 Sqm on plan and getting out in soft/ loose soil including cutting road surfaces complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness complete all as specified and as directed. (Note :- Punned thickness will be measured for payment purpose)

Supplying and fixing/ laying of 40mm bore dia GI pipe medium grade in trenches including all necessary fittings & clamps made out of 25x3mm flat iron as required for cable protection etc complete all as specified and directed.

Supply and laying Sub Class 'B' bricks well burnt laid in trenchs as cable cover all as specified and as directed.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

M&L for 100 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L for 60mm thick rubber mould reflective factory made coloured pre cast PCC interlocking paver blocks/ tiles confirming to IS 15658-2006, M-35 designation of section as approved by GE in hard standing, laid dry over & including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed.

M&L for RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.50M clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plates etc and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete all as specified and directed. Note:- Reinforcement shall be measured & paid for separately under respective item of BOQ.

Schedule of credit amount of Rs. 2,27,495.00 to be deducted during AOC

Tiki Water proofing Co

RAVINDRA ELECTRICAL

Rai Construction Co

Kirti Chandeliya and Assosicates

DEEPAK CONSTRUCTION

RAVI ENTERPRISES

VEENUS ENGINEERS

J.P ENTERPRISES

M/S Modern builders

M/s SKP CONSTRUCTION