Improvement, Upgradation and Renovation of State Guest House No-1 at Koinadhara, Khanapara, Guwahati-22 (Temporary conversion for Rajbhawan Assam ) (Phase-II) (Electrical works).

Amount

Supplying installation, testing, programming and commissioning of On-table Boundary Layer Microphone With Programmable Microphone Button (PTT, PTM, toggle ON/off, permanent on) And A Bi-color LED Ring For Status Indication; Frequency Response Of 40 Hz – 20 kHz;

Supplying installation, testing, programming and commissioning of Audio equipment LAVALIER SET: Receivers AF frequency response 50 to 16,000 Hz (–3 dB), Microphone Sensitivity < 3 μV at 52 dB(A)rms S/N, Input sensitivity 1.5 mV / Pa

Supplying installation, testing, programming and commissioning of Audio equipment,8" Open‐Back Ceiling Speaker. 70V/100V taps at 6W, 3W, 1.5W (plus 0.75W at 70V), very high 97 dB sense, 50 Hz to 16 kHz, for non‐plenum applications, 1.4 kg (3.0 l.

Supplying installation, testing, programming and commissioning of Professional 4-Channel Power Amplifier; 4 x 75 Watts Into 4 Ohms; 4 x 50 Watts Into 8 Ohms;

Supplying installation, testing, programming and commissioning of Dual 2 Way 5" Full Range Surface Mount Loudspeakers with Line Transformers;120 Watts Continuous, 480 Watts Peak power; 120, 60, and 30W On The 100 V Line

Supplying installation, testing, programming and commissioning of Ultra-Lightweight, High-Density Power Amplifier Delivers 2 x 500 Watts into 2 Ohms; 2 x 300 Watts into 4 Ohms; 1000 Watts into 4 Ohms (bridge mode)

Supplying installation, testing, programming and commissioning of Advanced Digital Audio Processor with Confi gurable DSP, Audio Networking 30 high-headroom analogue universal mic/line inputs, 18 electronically balanced low impedance line level outputs

Supply and Laying of High flexible Speaker cable for power amplifiers upto minimum 500 Watt , Jacket - PVC, ø 0.32 in, black Conductor - Stranded bare copper wires, 140x35 AWG (13AWG) ,

Supply and Laying of Audio Signal Cable;Balanced microphone cable with single shield, high flexible, velvet faint PVC-Jacket , Conductor: Stranded bare copper wires 28 x 0.10 mm (0.22mm²) , Jacket: PVC, 6.0 mm max. Ø

Supply and Installation of XLR connectors Male

Supply and Installation of XLR connectors Female

Supply and Installation of 1/8" (3.5mm) Balanced Phono Plug

Supply and Installation of Speakon Connector

Supply and Installation of RCA Connector

Supply and Installation of 6KVA Online UPS with Batteries and Battery Rack

Supply and Laying of PVC Conduit

Supply and Installation of 24U Equipment Rack

Supply, Installation, Testing and Commissioning of 55" Video Wall Display (0.88mm) . Screen Size:- 139.7cm (55), Resolution:- 1,920 x 1,080 (FHD), Brightness(Typ.,cd/m²):- 700, Bezel Width:- 0.44mm (Even), Total Bezel:- 0.88mm, Monitor Dimension (W × H × D):- 1,210.51 x 681.22 x 86.5 mm, Operation Temperature:- 0°C to 40°C, Power Supply:- 100-240 V~, 50/60 Hz, Content Management Software:- SuperSign CMS,

Wall Mount Bracket For Video Wall

Supply, Installation, Testing and Commissioning Of 55 inches Full HD LED TV With Resolution Of 1920 x 1080(FHD); Visible Screen Size (diagonal) 138 cm; Terminal- 2 x HDMI, 2 x USB, 1 x Component Video Input, 1 x Composite Video Input, 1 x Digital Audio Output (Optical), 1 x AV Out, 1 x PC Input;

Supply, Installation, Testing and Commissioning Of 18.5" Monitor.

Supply, Installation, Testing and Commissioning of Popup Box; Easy Access To Connectors Durable Pnematic Movementand Mechanical Latching Mechanism One Female 15pin HD Connector And 3.5mm Mini Stereo Audio Jack, Two CAT RJ45 Network/Data/Phone Connectors, Two Unswitched AC Outputs, One HDMI

Supply, Installation, Testing and Commissioning of 8-Port HDMI Switch: Video Input: Interfaces 8 x HDMI Type A Female (Black), Impedance 100 Ώ, Max. Distance 1.8 m; Video Output: Interfaces 1 x HDMI Type A Female (Black), Impedance 100 Ώ; Video: Max. Data Rate 6.75 Gbps (2.25 Gbps Per Lane), Max. Pixel Clock 225 MHz, Compliance HDMI (3D, Deep Color) , HDCP Compatible , Consumer Electronics Control (CEC), Max. Resolution Up to 1080p, Max. Distance Up to 15 m; Audio: Input 8 x HDMI Type A Female (Black), Output 1 x HDMI Type A Female (Black), Control RS-232 Connector: 1 x DB-9 Female (Black), Baud Rate and Protocol: Baud Rate: 19200, Data Bits: 8, Stop Bits:1, Parity: No, Flow Control: No

Supply, Installation, Testing and Commissioning of VGA to HDMI Converter with Scaler: Video Input: Interfaces 1 x HDB-15 Female (Blue), Impedance 75 Ώ; Video Output: Interfaces 1 x HDMI Type A Female (Black), Impedance 100 Ώ; Video: Max. Pixel Clock 165 MHz, Max. Resolution Up to 1080p, Scaler Resolutions 480p; 480i; 576p; 576i; 800 x 600; 1024 x 768; 1280 x 720; 1280 x 1024; 1360 x 768; 1440 x 900; 1400 x 1050; 1600 x 1200; 1680 x 1050; 1080i; 1080p; 1920 x 1200; Audio: Input Analog: 1 x Mini Stereo Jack Female (Black); Digital: 1 x RCA (Yellow)

Supply, Installation, Testing and Commissioning of HDMI Repeater Plus Audio De-embedder: Video Input: Interfaces 1 x HDMI Type A Female (Black), Impedance 100 Ώ; Video Output: Interfaces 1 x HDMI Type A Female (Black), Impedance 100 Ώ; Video: Max. Data Rate 6.75 Gps (2.25 Gbps Per Lane), Max. Pixel Clock 225 MHz, Compliance HDMI (3D, Deep Color) , HDCP Compatible, Max. Resolution Up to 1920 x 1080; Audio Output 1 x HDMI Type A Female (Black); 1 x Toslink (Black); 1 x RCA (Orange); 2 x RCA (Red/White);

Supply, Installation, Testing and Commissioning of 8-Port HDMI Splitter: Video Input Interfaces 1 x HDMI Type A Female (Black), Impedance 100 Ώ, Max. Distance 1.8 m; Video Output Interfaces 8 x HDMI Type A Female (Black), Impedance 100 Ώ; Video, Max. Data Rate 10.2 Gbps (3.4 Gbps Per Lane), Max. Pixel Clock 340 MHz, Compliance HDMI (3D, Deep Color, 4K); HDCP Compatible, Max. Resolution Up to 4096 x 2160 / 3840 x 2160 @ 60Hz (4:2:0); 4096 x 2160 / 3840 x 2160 @ 30Hz (4:4:4); Max. Distance Up to 15 m, Audio Input 1 x HDMI Type A Female (Black); Output 8 x HDMI Type A Female (Black); Control RS-232 Connector: 1 x DB-9 Female (Black) Baud rate and protocol: Baud Rate: 19200, Data Bits: 8, Stop Bits:1, Parity: No, Flow Control: No, EDID Settings EDID Mode:Default / Port 1 / Auto

Supply, Installation, Testing and Commissioning of HDMI over Single Cat 5 Extender: Video Input: Interfaces transmitter 1 x HDMI Type A Female (Black), Impedance 100 Ώ, Max. Distance 1.8 m; Video Output Interfaces reciever 1 x HDMI Type A Female (Black), Impedance 100 Ώ ; Video: Max. Data Rate 10.2 Gbps (3.4 Gbps Per Lane) 10.2 Gbps (3.4 Gbps Per Lane), Max. Pixel Clock Up to 340 MHz Up to 340 MHz, Compliance HDMI (3D, Deep Color, 4K) , HDCP Compatible , Consumer Electronics Control (CEC) HDMI (3D, Deep Color, 4K) , HDCP Compatible , Consumer Electronics Control (CEC), Max. Resolutions / Distance Up to 4K@70m (Cat 5e/6) / 100m ; Audio Input 1 x HDMI Type A Female (Black); Output 1 x HDMI Type A Female (Black)

Supply, Installation, Testing and Commissioning Of Video Conference System. Features: Video up to: 1080p, 720p Data up to: 1080p/ WUXGA 30fps Full band audio Dual screen support 12 Mbps bandwidth Support H.264,H.263++ and other video standards Full HD camera with pan, tilt and zoom features Digital Mic array with automatic echo cancellation and noise suppression.

Supply and Installation of Service Warranty Pack for Video Conference System

Supply and Laying of 15 mtr. High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable.

Supply and Laying of 10.7 mtr. High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable.

Supply and Laying of 1.8 mtr. High-performance Cables With Molded HDMI Connectors At Both Ends. HDMI Standard Supports High-definition Video Plus Multi-channel Audio In A Single Cable.

Supply and Laying of 0.9 mtr. High−performance computer graphics video cable with molded 15−pin HD connectors on both ends.

Supply and Installation of HDMI To DVI Converter

Supply and Laying of Cat 6 UTP Cables

Supply and Installation of Glass Tray for VC Unit

Supply, Installation, Testing and Commissioning of USB PTZ Camera: Equipped with a 1/2.8 inch image sensor or better USB 3.0 and HDMI video output interface or better Full HD 1080p signal output format with a high frame rate of 60 fps,12x optical zoom or better Applicable for a medium size conference room or better Viewing Angle: 74°(H) 82°(D) or better Wide range Pan/ Tilt/Zoom actions Pan angle from -100' to +100'; tilting angle from -30° to +30°. or better

Supply, installation, Testing and Commissioning of HDMI/VGA to HDMI Live Video Streamer with Recording Function: 1 HDMI input ,1 VGA input and 1 HDMI output (for local monitoring) are supported HDCP 1.x and HDCP 2.2 compliant or better HDMI input/output supports resolutions up to 4K UHD (18Gbps, 4K@60Hz 4:4:4, 8-bit) or better VGA input supports resolutions up to WUXGA (1920x1200@60Hz)or better Advanced H.264 video streaming and recording is provided at QVGA (320x240), VGA (640x480), 720p, or 1080p at up to 60fps or better

Supplying including installation of the Octagonal poles shall be designed to withstand the maximum wind speed of 169 km/hr. The top loading i.e. area and weight of fixtures are to be considered to calculate maximum deflection of the poles and the same shall meet the requirement of BS:5649 Part VI 1982. The pole shaft shall have octagonal cross section and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding of the pole shaft. The welding of the pole shaft shall be done by Submerged Welding process. All octagonal pole shafts shall be provided with the rigid flange plate of suitable thickness with provision for fixing 4 foundation bolts. The base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside. The welding shall be done as per process approved by Third Party Inspection agency. (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) * Pole Type BOP or equivalent-9030 Height 9m The materials of the pole as follows : Conforming to grade S355JO, Base Plate :- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts:- 6.8 Gr. As per IS 1367, Pole Sections:- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization :- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening:- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :-70, Bottom Dia.:- 155 , Sheet Thickness :- 3mm , Base Plate Dimensions :- (L x B x T) 260 x 260 x 16, Foundation Bolt Size :- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia.:- PC 250 Bolt Length:- 750, Projected Bolt Length :-125 Anchor plate thickness :- 4 mm , Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation:- The foundation shall be done with ( Earth work 2.04 cubic Meters.RCC 1:1.5 : 3 proportion 0.65 cubic metres. Steel 22.43 Kg). Shuttering 4.32 square metres. = 22.43 Kg)."

* Pole Type BSR or equivalent-1030 Height 10m The materials of the pole as follows : Conforming to grade S355JO, Base Plate:- Fe 410 Conforming to IS 226/ IS 2062, Foundation Bolts :- 6.8 Gr. As per IS 1367, Pole Sections :- The Octagonal Poles shall be in single piece with single longitudinal welding join, Galvanization:- The poles shall be hot dip galvanized as per IS 2629 / IS 2633 / IS 4759 standards with average coating thickness of 65 micron. The galvanizing shall be done in single dipping. Door opening :- The Octagonal poles shall have door of approximate 500 mm length at the elevation of 500 mm from the base plate. The door shall be vandal resistance and shall be weather proof to ensure safety of inside connection as approved by the Depts.. The door shall be flush with the exterior surface and shall have suitable locking arrangement. The pole shall be adequately strengthened at the location of the door compensate for the loss in section. There shall also be suitable arrangement for the purpose of earthing, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Top Dia. :- 100, Bottom Dia.:- 200, Sheet Thickness :- 3mm, Base Plate Dimensions :- (L x B x T) 310 x 210 x 20, Foundation Bolt Size :- (no. x dia.) 4 x 24 Dia, Pitch Circle Dia. PC :-270, Bolt Length :-750, Projected Bolt Length :-125, Anchor plate thickness :- 4 mm, Pole Foundation :- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation :- The foundation shall be done with ( Earth work :- 2.04 cubic Meters.RCC :- 1:1.5 : 3 proportion 0.65 cubic metres. Steel :- 22.43 Kg). Shuttering :- 4.32 square metres. = 22.43 Kg).

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (BAJAJ/ PHILIPS/ VALMONT/ PARUTHI ENGR/Nezone make) Stiffener plate from arm of the following types : " * Single arm bracket 2000mm long for 3m to 10 metre. Poles.

*Supplying and installation and commissioning of vermin and dust proof totally enclosed double door cubical type compartmental floor mounting panel board of size 1.20 m ×1.00 m ×0.50 m made of 16 SWG (1.66mm) thick CR sheet and 35 mm × 35 mm × 6 mm size angle and 35 mm ×6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coats of enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 40 Amp 4 pole 415 Volt 50 Hz MCCB as incomer - 1 no 2. 32 Amp 2 pole open execution with HBC fuse SDFU unit as outgoing - 3 nos. /32 A DP MCB 3 Nos/ 32A DP RCBO 3 NOS. 3. 25 mm × 5 mm size 4 strip copper Bus-Bar- 1 set 4. 40 Amp 4 pole ON-OFF poser contactor - 1 No. 5. Surface mounting timer switch - 1 No. 6. 63 Amp bakelite HBC fuse kit-kat - 3 Nos

Supply, installation & testing of G.I. Plate earth station with 600 mmx600 mmx6 mm heavy duty G.I. earth plate with necessary 40 mm dia. G.I. watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm hinged cover C.I. cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt 5 Kg and Charcoal 96 Kg in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

Supplying & laying of 25x6 mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 16.00 Sq.mm 3 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 25.00 Sq.mm 3 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 35.00 Sq.mm 3 Core armoured U.G. cable

Supplying,installation,testing and commissioning of pressure die cast powder coated aluminium alloy housing frosted PC diffuser, IP65/IP66 protection of the following street light including connection with 2.5 Sq.mm. 3 core PVC insulated round copper conductor as required and as directed by the department. f BRP 322 LED 142 CW HE MR FG S4 XTFC L GR

Supplying,installation,testing and commissioning of the following integral flood lighting luminaires conforming to IP 65 / IP 66 suitable for vertical and horizontal mounting applications pressure die cast powder coated aluminium alloy housing with corrosion resistance powder coating using nano Technology transparent injection moulded poly carbonate UV stabilized diffuser having high impact strength to withstand min IK09 with high power LED and unique flood optics to ensure uniform light distribution and maintenance free system ideal for area lighting, high mast lighting, sports lighting and billboard. The luminaires should be equiped with external surge protection device to withstand 10 KV / 5KV including connection with 2.5 sqmm 3 core PVC insulated round copper conductor as required and as directed by the department. e BVP 122 LED 150 CW HE NB FG XTFCL S4

Supplying including installation, commissioning of HENSEL make ENYCASE DK Thermoplastic cable Junction Boxes conforming to IP66/67 weather proof for outdoor installation with knockouts for cable entry complete as specified and directed by the deptt. h HENSEL ENYCASE DK THERMOPLASTIC CABLE JUNCTION BOXES.CAT NO.K 8250 HENSEL ENYCASE DK THERMOPLASTIC CABLE JUNCTION BOXES.CAT NO.K 8250 HENSEL ENYCASE DK THERMOPLASTIC CABLE JUNCTION BOXES.CAT NO.K 8250

Supplying, erection and commissioning of the following specification as per IS:2713 : 410 SP hot dip Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having a base plate including providing all required building materials as directed and specified by the deptt. (BANSAL/SRP / Valmont / PARUTHI ENGR make) * 410 SP 76 Length of pole = 14.50 metre., Length of sections, Bottom = 6.50 M, Middle = 4.00 M, Top = 4.00 M, Out side dia. & Thickness Bottom =219.10 x 5.90 mm, Middle =193.70 x 4.85, Top =165.10 x 4.50 mm

Supplying, installation testing and commissioning of the following rating copper wound indoor / out door type transformer complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure. * 250 KVA,50Hz.11/0.433 KV. Oil filled transformer with Off Circuit tap change.

Supplying and fixing of 11 KV 150 A D.O. fuse set complete as required and as directed by the department.

Supplying and fixing of 11 KV 5 KA Lighting arrestor (Poly) set complete as required and as directed by the department.

Supplying with fitting and fixing of P.G. clamp for Racoon conductor complete as required and as directed by the department.

Supplying and string up AAAC Racoon conductor in the existing P.S.C./ M.S/ Galvanized pole with binding etc. as required and as directed by the department. Directed by the department.

Supplying including installation of 4” dia. C.I. earth pipe complete as required and as directed by the department.

Supplying, erection and commissioning of the following specification as per IS:2713 : 410 SP hot dip Galvanized Steel tubular pole manufacturing out from electrically welded in 3 (three section having a base plate including providing all required building materials as directed and specified by the deptt. (BANSAL/SRP / Valmont / PARUTHI ENGR make) * 410 SP 36, Length of pole = 9.50 metre., Length of sections, Bottom = 5.00 M, Middle = 2.25 M, Top = 2.25 M, Out side dia. & Thickness Bottom = 138.7 x 5.40 mm, Middle =114.30 x 4.50 mm, Top =88.9 x 3.25 mm

Supplying and erection of 11 KV Pin insulator (Poly) with G.I.pin, blots and nuts coach screw etc. as required and as directed by the department.

Supplying and erection of 11 KV Disc insulator (Poly) 45 KN with hard ware fittings etc. as required and as directed by the department.

Supplying with fitting and fixing of 11 KV T Cross arm complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supplying with fitting and fixing of galvanised channel of 100 mm x 50 mm x 6.5mm, 2200 mm long complete with clamps ,blots, nuts etc. as required and as directed by the department.

Supplying with fitting and fixing of H.T. danger plate complete as required and as directed by the department.

Supplying and erection of H.T. stay set complete (Galvanized) with 19mm dia x1.8m long stay rod anchor plate of size 30cm x 30cm x6.4 mm, thimble stay clamps, turn buckle (19mmx 60cm) 7/3.15 mm dia G.I. stay and strain insulation etc. in cement concrete 1:3:6 (1Cement:3Course sand:6graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc. as required and as directed by the department.

Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx6 mm heavy duty copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt 5 Kg and Charcoal 96 Kg in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

Supplying & laying of 40x6 mm size Copper strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supply including fitting and fixing of 11 KV SCREENED XLPE cables heat shrink type single core HT cable outdoor termination Kits RAYCHEM RPG including all accessories for the following sizes including testing and commissioning as specified and directed by the Deptt.* 120.00 to 240.00 Sq.mm., 1 Core cable.

Supply and laying 11/33 KV HT 3 core Stranded compact Circular Aluminium Conductor, Conductor Screen With Extruded Semi Conducting compound, XLPE Insulated, Insulation Screening with truded Semi Conducting compound in combination with Copper Tape (0.3kA for 1 se , cores laid up, inner sheath of PVC tape, galvanised flat steel strip armoured and overall PVC Sheathed cable conforming to IS 7098 / (PART-I 1985 with latest amendment cable laid through medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.) / partially in air as required for connection as directed, including excavation of trench, refilling reconstruction of damaged done to road, drain, wall et as specified by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make or equivalent) * 95mm 3 Core armoured 11 KV (H.T. U.G. cable laid through 100mm dia hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.) )

Supplying fitting and fixing of transformer bushing

Heat curing and tanking of transformer

Oil filter and filling after dehydration of transformer

Supplying fitting and fixing of transformer new gasket set complete

Cleaning, painting, varnishing oftransformer tank both inside and outside

Testing of transformer

Transformer oil refilling

Supplying and fixing of 11 KV 400 A Gang operated switch with all accessories complete as required and as directed by the department.

Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection powder painted sheet steel enclosure fitted on angle iron frame of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. *(ABB, Schneider, legrand, L&T make) * 250 A

Supplying with fitting and fixing Four Pole 415V Front handle operated On Load Change over switch (IP-20 protection powder painted sheet steel enclosure fitted on angle iron frame of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. *(ABB, Schneider, legrand, L&T make) * 400 A

Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. *35/36 KA 415V 50 Hz 4P MCCB (C&S, Havells, Indo Asian, HPL, V-Guard or equivalent make as approved by the Deptt.) * 250 A

Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.* 400 A

Supplying with fitting and fixing panel mounting open execution 25 KA 415V 50Hz 3P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. *25 KA 415V 50 Hz 3P MCCB (Havells, HPL, Indo Asian make)" *63A

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 95.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 185.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Load Security & Meter Security to be paid to the APDCL authority as per direction of the department. (payment will be made by department after production of APDCL Demand Note)

Transformer Pad as per APDCL Schedule of Rate 2018-19 Sl No 429

Supply, Installation, Testing & Commissioning of Toshiba/Carrier/Bluestar Make Air-Cooled Celling Suspended stable power inverter ducted having Reciprocrating Comprressors and microprocessor-based Control Panel.*3.0 HP stable power inverter ducted Unit

Supply, Installation, Testing & Commissioning of Toshiba/Carrier/Bluestar Make Air-Cooled Celling Suspended stable power inverter ducted having Reciprocrating Comprressors and microprocessor-based Control Panel.*4.0 HP stable power inverter ducted Unit

Supply, Installation, Testing & Commissioning of Toshiba/Carrier/Bluestar Make Air-Cooled Celling Suspended stable power inverter ducted having Reciprocrating Comprressors and microprocessor-based Control Panel.*5.0 HP stable power inverter ducted Unit

Supply, Installation, Testing & Commissioning of Toshiba/Carrier/Bluestar make 1.0 TR R-32 5Star Inverter Hi-Wall Unit for dressing room

Supply, Installation, Testing & Commissioning of Toshiba/Carrier/Bluestar make 2.0 TR r-32 5Star Inverter Hi-Wall Unit for dressing room

AIR COOLED VRF UNITS*Supply, Installation, Testing & Commissioning of Carrier/ Bluestar/voltas make Variable Refrigerant Volume modular type airconditioning system complete with indoor and outdoor units, individual remote with refrigerant piping, control cabling as per detail given in drawing and having following items:*OUTDOOR UNITS: *20.0 HP Outdoor unit (For Conference & Dining area)

INDOOR UNITS:* Supply, Installation, Testing & Commissioning of Carrier/ Bluestar/Voltas Make Air-Cooled Celling Suspended Indoor units suitable for VRF with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, outer cabinet, drain pan, insulation, pipe connections etc. of various capacities as per drawings etc. *5.6 TR Ductable Unit (Dining Area)

INDOOR UNITS: Supply, Installation, Testing & Commissioning of Carrier/ Bluestar/Voltas Make Air-Cooled Celling Suspended Indoor units suitable for VRF with pre-filter, fan section with low noise fan, multispeed motor, coil section with DX coil, outer cabinet, drain pan, insulation, pipe connections etc. of various capacities as per drawings etc. *4.6 TR Ductable Unit (Conference room)

Supply & Fixing of Y-joints as required size

Refrigerant Piping*Supply & Laying of Soft Drawn Copper refrigerant piping interconnecting the outdoor & indoor units with insulation for 3.0 HP stable power inverter ducted Unit.

Refrigerant Piping*Supply & Installation of Soft Drawn Copper refrigerant piping interconnecting the outdoor & indoor units with insulation for 4.0 HP & 5.0 HP stable power inverter ducted Units.

Refrigerant Piping*Supply Laying, Testing & Commissioning of Refrigerant Copper piping with closed cell Nitrile Rubber insulation interconnecting for VRF indoor & outdoor Unit.

Control and Transmission Wiring*Providing & fixing Copper control cable of 3Core x 1.5 sqmm copper in suitable PVC conduits between indoor and outdoor unit complete with interconnecting control cables as per drawings

Drain Piping* Supply & Fixing of 25mm Hard PVC drain pipe

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. "24G Galvanized Sheet Steel Ducting

Supplying & fixing of powder coated extruded aluminium Supply Air Slotted Grille with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Slotted Grille without aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Exhaust Air Grille without aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Eye Ball Diffuser without aluminium volume control dampers as per specifications. For waiting room

Supply,installation,testing and commissioning of fire retardant nonporous double layer flexible connection between machine and ducting.

Supplying, installing & testing of Thermal Insulation for supply / return air duct as per technical specification. (closed cell Nitrile Rubber, Class 'o', 25.0 mm thick for supply air duct)

Supplying,Fixing & testing of Acoustic lining within supply /return air ducts with 25 mm thick acoustic lining of fiber glass wool as per technical specification.

Supply & charging of R-410 Refrigerant Charge

Supply & Installation of M.S. Stand for Split O.D.Units

Material With Labour for Minor Civil work

Supply & fixing of Machine Hanging Arrangements Support & Angle

Providing labour for Rework of ducting dismantling and reinstallation of the same

Supply, Installation, Testing & Commissioning of 300 cfm Toilet Inline Fan for toilet exhaust

Wiring to a 5 pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete.* Short point up to 3.00 metre. length.

Wiring to a 5 pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete.* Medium point up to 6.00 metre. Length.

Wiring to a 5 pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete.* Long point up to 10.00 metre. Length.

"Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) "* Short point up to 3.00 metre. length.

"Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) "*Medium point up to 6.00 metre. Length.

"Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) "*Long point up to 10.00 metre. Length.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) complete* Short point up to 3.00 metre. length.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) complete* Medium point up to 6.00 metre. Length.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system with 20mm dia 2mm thick / heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) complete* Long point up to 10.00 metre. Length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.*With 3 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.*With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.*With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.*With 2 x 10 sq. mm. + earth continuity with 1x 6 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including earth continuity in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system .*With 3 x 2.5 sq. mm. + earth continuity with 2x1.5 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. (for UPS Points)

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including earth continuity in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system .*With 3 x 4 sq. mm. + earth continuity with 2x 2.5 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit. (for UPS points)

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.*With 4 x 4 sq. mm. + earth continuity with 2x2.5 sq. mm. cable in 25 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.*With 4x 6 sq. mm. + earth continuity with 2x4 sq. mm. cable in 32 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.*With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system.*With 4 x 16 sq. mm. + earth continuity with 2x10 sq. mm. cable in 40 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supply and fixing of 19 mm dia 1.50mm to 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) on surface system including painting etc as required: (for CCTV,Data & Tel. wiring)

Supply and fixing of 25 mm dia 1.50mm to 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) on surface system including painting etc as required: (for CCTV, Data & Tel. wiring)

Supply and fixing 32 mm dia 2.00mm average wall thickness heavy rigid PVC IS: 9537 Part - III conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) on surface system including painting etc as required: (for Data & Tel. wiring)

Supplying installation testing of UTP CAT6 Cable without PVC conduit

Wiring for Co - axial Jelly Flooded (Unarmoured) (FINOLEX /RR KABEL /NICCO / ANCHOR make) cable in existing surface conduit wiring system including connection etc as required.*Co - axial Jelly Flooded (Unarmoured) RG 11 (Copper)

FITING AND ACCESSORIES*Supplying and fixing of 3 plate Ceiling Rose (Anchor Penta PC CHERRY /Gold medal /Kolor kany.kom/Havells or equivalent make as approved by the Deptt.) on the existing block including connection as approved by the Deptt.)complete as required

FITING AND ACCESSORIES*Supplying and fixing of Call bell ( Buzzer ) including 6 amp capacity flush type bell push switch including connection as approved by the Deptt.)as required.

FITING AND ACCESSORIES*Supplying and fixing of Fan box (AKG or equivalent as approved by the Deptt.)with inbuild rod as required.

Supplying, fitting fixing of LED Batten Tubes high quality aluminium extruded with decorative end caps connection with 1.5 Sq.mm 1 core PVC insulated round copper conductor as required and as directed by the department. "*BN 021C LED 20 S PSU CW GR S2

Supplying fitting & fixing of LED Kubik Batten tube light fitting 300mm length as required and as directed by the department ( Jaquar or eqvt. make). "c kubik Series Batten tube fitting 20W

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-DN 393 B LED 12 S-6500 PSU WH / D01257R000 / D01240R000 / D01230R000 / CRDL11R017HP57 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make).

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-DN 394B LED 16 S -6500 PSU WH / MV1857RLOO / MV1840RLOO /MV1830RLOO / MV1830RLOO / MV1857R500 / MV1857R500 / MV1840RLOO / CRDL11R023HP57 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / LT / Wipro make).

Supplying, installation, testing and Commission of the following indoor Decorative Recessed mounted 2' x 2' LED down lighter luminaries of model no- RC380 B LED 36S-6500 G4 L60 PSD OD WH OC / RC380 B LED 36S-6500 G4 L60 PSD OD WH OC / LCTRS-36-TL / LCTRS-36-CDL / IO2830RP00 / IO2840RP00 / IO2850RP00 complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips / Crompton / LT make).

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-LESP01R009XC / LESP01R009XN /LESP01R009XW / L00957R000 / L00940R000 / L00930R000 /LD90-111 - XXX-65-XX complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Jaquar / LT / Wipro make).

Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED round fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required. LED Round Light,6W * LED Round Light,6W

Supplying fitting and fixing of double wall brackets model FCG 308, (or equivalent as approved by the Deptt.) on the wall in GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover with all accessories including connection as required complete. ( without Lamp).

Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED outdoor light fittings complete with all accessories including connection cable, as approved by the Deptt.s etc. as required. * LED Ground Burial 4W

Supplying and fixing of table lamp model Philips 69066/30 LEDINO WALL LIGHT 2.5W (or equivalent as approved by the Deptt.) including connection as required.

Supplying and fixing of Philips 32071/31 LED 0.96W TYPE flush type circular ceiling fittings (or equivalent as approved by the Deptt.) complete with Shade, holder, back plate and LAMP holder, 20 Watt CFL lamp including connection as required.

Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt.s etc. as required complete and as directed by the Department [Without regulator]. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make)*Energy efficient 5-star 1200 mm sweep Fusion 5 star (Havells or equivalent make)

Supplying including fitting fixing of following star rated A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection cable, as approved by the Deptt.s etc. as required complete and as directed by the Department [Without regulator]. (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make)*Energy efficient 5-star 1200 mm sweep. ORIENT PSPO / Usha / CROMPTON / Havells/ ATC or equivalent make

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.*Domestic*Ventilator DX 250 mm sweep Louver type (ORIENT make), Brisk Air 250 mm sweep Louver type/ Trans Air 150 mm sweep (Crompton make), Ventil Air DX 150 mm sweep Louver type (Havells make)

Supplying and fitting fixing of Electric storage water heater [Geyser] of Bajaj/Crompton/Racold/V. Guard or equivalent make including necessary connection cable, as approved by the Deptt.)etc. as required complete and as directed by the Department. * Horizontal type *10.00 litres. capacity (5 Star Model) (Bajaj/Crompton/Racold make)

Supplying including fitting and fixing of the following Oil filled/heat converter/halogen heater complete as directed and specified by the deptt. (Bajaj or equivalent) * OFR 9F Oil filled heater

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. (For VRV Outdoor Unit) *ABB, Schneider MG, legrand, Hager make)* 8 way SPN single door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)* 8 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)* 12 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof IP-43 double door surface mounting horizontal Per Phase Isolation (PP DB incorporated with bas-bar 125A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)* 6 way TPN (8+6+18) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof IP-43 double door surface mounting horizontal Per Phase Isolation (PP DB incorporated with bas-bar 125A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)*8 way TPN (8+6+24) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof IP-43 double door surface mounting horizontal Per Phase Isolation (PP DB incorporated with bas-bar 125A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)* 12 way TPN (8+6+36) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof IP-43 double door surface mounting Vertical Per Phase Isolation (PP DB incorporated with bas-bar 125A, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. *ABB, Schneider MG, legrand, Hager make)* 6 way TPN (8+6+18) double door

"Supplying with fitting and fixing Single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*B Series (Schneider MG, legrand, Hager make)"*6 to 32A

"""Supplying with fitting and fixing Single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*C- Series (Schneider MG, legrand, Hager make) (Schneider MG, legrand, Hager make)"*6 to 32A

"Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*C Series (ABB, Schneider MG, legrand, Hager make)"*6 to 32A

"Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*C Series (ABB, Schneider MG, legrand, Hager make)"*40A

"Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*C Series (ABB, Schneider MG, legrand, Hager make)"*63A

"Supplying with fitting and fixing TP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*C Series (ABB, Schneider MG, legrand, Hager make)"*40A

"Supplying with fitting and fixing TP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*C Series (ABB, Schneider MG, legrand, Hager make)"*63A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. (for LDB., PDB)*C Series (ABB, Schneider MG, legrand, Hager make)*Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. (for LDB., PDB)*C Series (ABB, Schneider MG, legrand, Hager make)6 to 32

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. (for LDB., PDB)*C Series (ABB, Schneider MG, legrand, Hager make)*40A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. (for LDB., PDB)*C Series (ABB, Schneider MG, legrand, Hager make)*63A

"Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*30mA sensitivity DP RCCB (for LDB, PDB, ACDB) (ABB, Schneider MG, legrand, Hager make)"*25A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*30mA sensitivity DP RCCB (for LDB, PDB, ACDB) (ABB, Schneider MG, legrand, Hager make)"*40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*30mA sensitivity DP RCCB (for LDB, PDB, ACDB) (ABB, Schneider MG, legrand, Hager make)"*63A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*"100/300mA sensitivity DP RCCB (ABB, Schneider MG, legrand, Hager make)" (ABB, Schneider MG, legrand, Hager make)"40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*""100/300mA sensitivity DP RCCB (ABB, Schneider MG, legrand, Hager make)"" (ABB, Schneider MG, legrand, Hager make)""40A"*63A

SURGE PROTECTION & OVER VOLTAGE PROTECTOR*Supplying with fitting and fixing Surge protector of max operating voltage 350V at 400V network for maximum discharge current 40KA, with operator indicator and draw out cartridge of Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the deptt. * 1P + N

SURGE PROTECTION & OVER VOLTAGE PROTECTOR*Supplying with fitting and fixing Surge protector of max operating voltage 350V at 400V network for maximum discharge current 40KA, with operator indicator and draw out cartridge of Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the deptt.* 3P + N

MCCB with Thermal & Magnetic Release*Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*25 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens, Indo Asian make) *63A

MCCB with Thermal & Magnetic Release*Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*25 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens, Indo Asian make) *80A

MCCB with Thermal & Magnetic Release*Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*25 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens, Indo Asian make) *100A

"Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*35/36 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens make)"*160A

"Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*35/36 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens make)"* 250A

"Supplying with fitting and fixing panel mounting open execution 35/36KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*35/36 KA 415V 50 Hz 4P MCCB (Schneider, legrand, Siemens make)"* 400 A

CHANGE OVER*Supplying with fitting and fixing Four Pole 415V Front handle operated open execution On Load Change over switch fitted on the existing cubical panel of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*ABB, Schneider, legrand, L&T make)*63A

CHANGE OVER*Supplying with fitting and fixing Four Pole 415V Front handle operated open execution On Load Change over switch fitted on the existing cubical panel of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.*ABB, Schneider, legrand, L&T make)*400 A

Supplying and installation and commissioning of vermin and dust proof totally enclosed double door cubical type compartmental floor mounting panel board of size 1.20 m ×1.00 m ×0.50 m made of 16 SWG (1.66mm) thick CR sheet and 35 mm × 35 mm × 6 mm size angle and 35 mm ×6 mm flat iron having 4 nos legs at the bottom and G.I. Sheet reefing on the top complete painting with 2 coats of red oxide metal primer and 2 coats of enameled paint. The panel board is to be erected in 1:3:6 RCC pole foundation including excavation of trench and brick soling etc. complete neatly internal wiring done as specified and directed by the department comprising of the following electrical items. 1. 40 Amp 4 pole 415 Volt 50 Hz MCCB as incomer - 1 no 2. 32 Amp 2 pole open execution with HBC fuse SDFU unit as outgoing - 3 nos. /32 A DP MCB 3 Nos/ 32A DP RCBO 3 NOS. 3. 25 mm × 5 mm size 4 strip copper Bus-Bar- 1 set 4. 40 Amp 4 pole ON-OFF poser contactor - 1 No. 5. Surface mounting timer switch - 1 No. 6. 63 Amp bakelite HBC fuse kit-kat - 3 Nos

Supply with installation & commissioning of readymade maintenance free CPRI approved chemical earthing system with 50 mm dia. 3.00 Metres length corrosion free dual pipe technology G.I. CHEMRODE ELECTRODE complete with RESLOW Grounding Minerals (25 K and Advance Earth Pit cover (PV including excavation of earth pit and construction brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the deptt.

Supply, installation & testing of G.I. earth station with perforated 50 mm dia and 3.00 Metre long heady duty G.I. pipe with necessary 50 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 65 mmx50 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of following size (25mm X 6mm) G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of following size (25mm X 6mm) Copper strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system.*With 2 x 16 sq. mm. + earth continuity with 1x 10 sq. mm. cable in 32 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Supplying & laying of 6 SWG G.I. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt. (for A.C. ODUs' & ExternalLightning Earthing)

Supply, fitting & fixing 20 mmx5 mm G.I. strips drawn on vertically or horizontally on building wall/parapet wall in surface system complete with supply of G.I. Nuts & Bolts, Screws etc including riveting, soldering and making connection as approved by the Deptt.)with earth electrode G.I. strips and Lightning Arrestor etc. as specified and directed by the deptt.

Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid Copper tube having 85 mm dia. single prong at top and 3 mm thick base plate at bottom complete with fitting & fixing with Brass nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Supply, installation & commissioning of Advanced Lightning protection system by using High pulse Voltage ESE Lightning conductor with Optimized Pulse Rod (ABB or equivalent make) as specified and directed by the deptt (as per NFC 17 - 102 STANDARD & IEC Std 60 - 111989)

Supply with installation & commissioning of readymade maintenance free CPRI approved chemical earthing system with 50 mm dia. 3.00 Metres length corrosion free Single pipe technology- Copper CHEMRODE ELECTRODE complete with RESLOW Grounding Minerals 25 K and Advance Earth Pit cover PV including excavation of earth pit and construction of brick earth chamber including plastering both inner & outer surface of brick wall as specified and directed by the deptt.

Supplying & laying of 50x6 mm size G.I. strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of G.I. nuts & bolts, screws etc including riveting, soldering & making necessary connection as approved, specified and directed by the deptt.

Supplying & laying of 8 SWG Copper earth drawn through 15 mm dia. Medium quality G.I. pipe from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *2 Core A2XWaY A2XFaY* 6.00 Sq.mm 2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *2 Core A2XWaY A2XFaY*10.00 Sq.mm 2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 3 & 1/2 Core A2XFY* 25.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 3 & 1/2 Core A2XFY* 50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 3 & 1/2 Core A2XFY*95.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 3 & 1/2 Core A2XFY* 185.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris et to proper place as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . * 3 & 1/2 Core A2XFY* 300.00 Sq. mm.3 & 1/2 Core armoured U.G. cable (Including Standby)

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *Core - 3.5 A2XFY*25 Sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *Core - 3.5 A2XFY*50 Sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *Core - 3.5 A2XFY*95 Sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *Core - 4 A2XWY A2XFY*10 Sq.mm four core armoured cable

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *Core - 4 A2XWY A2XFY*16 Sq.mm four core armoured cable

Supply and laying of following size armoured telephone cable laid in air or through existing cable trench/ duct/ cable tray/ HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . *20 pair

Supplying, laying of HDPE Pipe /DUCT IS 4984: 1995 as required in the existing trench, through micro tunneling, as directed and specified by the department. *75 mm PE63 GRADE PN6

Supplying, laying of HDPE Pipe /DUCT IS 4984: 1995 as required in the existing trench, through micro tunneling, as directed and specified by the department. *110 mm PE63 GRADE PN6

Drawing of cable through HDPE pipe / duct, cable trench, cable tray as directed and specified by the deptt.

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) DOUBLE compression BRASS GLANDS WITH NICKEL - PLATED*WEATHERPROOF (CBW) Size: 8 - 10, 3/4 "

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) DOUBLE compression BRASS GLANDS WITH NICKEL - PLATED*WEATHERPROOF (CBW) Size: 1Size: 2.5 - 16, 3/4 "

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) DOUBLE compression BRASS GLANDS WITH NICKEL - PLATED*WEATHERPROOF (CBW) Size: 60.5 - 66, 3 "

"SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) SINGLE compression BRASS GLAND HEAVY DUTY "*SINGLE compression BRASS GLAND HEAVY DUTY Size: 3/4"

"SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) SINGLE compression BRASS GLAND HEAVY DUTY "*SINGLE compression BRASS GLAND HEAVY DUTY Size: 1"

"SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) SINGLE compression BRASS GLAND HEAVY DUTY "*SINGLE compression BRASS GLAND HEAVY DUTY 1-1/4"

"SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) SINGLE compression BRASS GLAND HEAVY DUTY "*SINGLE compression BRASS GLAND HEAVY DUTY Size: 1 -1/2"

"SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) SINGLE compression BRASS GLAND HEAVY DUTY "*SINGLE compression BRASS GLAND HEAVY DUTY Size: 1 - 3/4"

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 6

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 10

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 16

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 25

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 50

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 95

SUPPLYING FITTING AND FIXING OF (DOWELLS/ COMET make) ALUMINIUM REDUCER terminal. Size: *ALUMINIUM REDUCER terminal. Size: 185

Supplying, installation of GI PERFORATED cable tray on wall or from ceiling including necessary channel, nuts and bolts, washer etc. as required as directed and specified by the department. (LEGRAND/ AKG /STRUTFAST make). * Size of Tray*152

Supplying, installation of GI PERFORATED cable tray on wall or from ceiling including necessary channel, nuts and bolts, washer etc. as required as directed and specified by the department. (LEGRAND/ AKG /STRUTFAST make). * Size of Tray*304

Supplying with fitting fixing of 6 amp one way modular clip in Bell push MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 10 Amps 3 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 6/10 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 6/10 amp two way modular clip in switch , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.*1-2 module type Metal

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.*3 module type Metal

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.*4 module type Metal

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.*6 module type Metal

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.*8 module type Metal

Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department.*9 module type Metal

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*1 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*2 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*3 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*4 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*6 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*8 module

Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department.*9 module

Supplying including fitting and fixing of TV SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of RJ-11 Telephone jack , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of blank plate single in modular switch system , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of electronic modular fan speed controller 2 - module type MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.*100 watt electronic modular 4 step speed control 2 - module type

Supplying with fitting and fixing of LED Foot lamp with Box MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of electronic chime MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of 20 A energy key switch tag with Time delay 3 M, MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE including making necessary connection as per direction of department.

Supplying with fitting and fixing of key tag, for MODEL RANGE LEGRAND (MYRIUS), ANCHOR (VIOLA), MK (WRAPAROUND/ PLUS), ABB (CHEIRON), KOLORS (KREST), SCHNEIDER (VIVACE), CRABTREE energy key switch as per direction of department.

Supplying including installation of door operated Limit Switch in Cup-board including making necessary connection as per direction of department.

Supplying including installation of Shaver socket outlet 230/12V, 2/3 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying ,installation, testing & commissioning of Hi-Path 1150 Digital Communication System equipped with the following: 8 P&T Ports - 46 Extension Ports (non upgradeable) Auto Call Back ; Built-in FAX/DID Built in Voice Guided Direct inward Dialling 3 party Conference In-built Caller ID 100% Non-Block. Supports PRI/BRI ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Distribution Box 20 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Distribution Box 50 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of IPM( Integrated Protection Module , ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Digital Profiset 3030 for one Touch Button & Busy Extension Indicator for Reception & Boss, ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Dedicated EPABX Earthing for trouble free operation ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of UROSET 2005 Analog Hand set ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Constant Voltage Transformer 500 VA ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of 2 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying installation testing and commissioning of 1/3", Varifocal, 2.8 ~ 10 mm, DC Auto Iris, CS Mount (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation testing and commissioning of - 12x PTZ Dome Camera, 600 TVL (Colour) / 700 TVL (B/W), Min Illumination 0.2 Lux @ F1.67 (Colour) / 0.004 Lux (B/W), 12x Zoom (3.94 ~ 46.05 mm), Digital 16x, True Day & Night (ICR), 1/4" Super HAD CCD (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation testing and commissioning of PTZ Control Keyboard, OSD Menu, 3D Joystick Control, 16 x 2 Character LCD (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation of BNC connection per Pair ()X make

Supplying installation testing and commissioning of Power Supply SMPS Based 12V For 4 Camera (PROTEK make)

Supplying installation testing and commissioning of 22" LCD TFT Screen (SAMSUNG / ball / LG / MITASHI make)

Supplying installation testing and commissioning of UPS 1 KVA for Back Up (ball / ELNOVA / APC make)

Supplying installation testing of UTP CAT6 Cable without PVC conduit

Supply, Installation, Testing & Commissioning of Microprocessor based fire Alarm control panel suitable for wall mounted type with audio visual indication zone i.e. rectifier and charger circuit and maintenance free battery of 2X12 volt with suitable Ampere hour capacity complete ( 08 Zone panel) make :AGNI / MORLEY or equivalent as approved by the Deptt.)

Supply, Installation, Testing & Commissioning of rate of rise & fixed temperature resettable Heat detector with mounting base. make : Apollo/Notifier/System Sensor make :AGNI / MORLEY or equivalent as approved by the Deptt.)

Supply, Installation, Testing & Commissioning of Fire Alarm Hooter with audible range of 25 metre 80 bb output complete. make :AGNI / System Sensor or equivalent as approved by the Deptt.)

Supply, Installation, Testing & Commissioning of Manual Call box made of M/s. Aluminium dia cast with epoxy coated paint with hammer & chain. make :AGNI / System Sensor or equivalent as approved by the Deptt.)

Supplying, installation of Photo Luminescent Exit board in RED/GREEN colour of size 300X150mm

Supply, Installation, Testing & Commissioning of Response indicator fitted on suitable type box with cover

Supplying, installation, testing & commissioning of Photo electronic Smoke Detector with mounting base complete in all respect.make:- APOLLO/Notifier/System Sensor or equivalent as approved by the Deptt.)

Supply & fixing of 2X1.5sq. mm. PVC insulated copper Armoured Cable on surface/ recess/ above false ceiling etc. as required. (ISI marked) )

Supplying including installation of UPS ( for EPABX & Emergency lighting)*15 KVA On-Line UPS System (Orion or equivalent make as approved by the Deptt.) with PWM-IGBT technology 360V AC Input (300V – 470V) 3 Ph input- 1 Ph output with Isolation Transformer 12KW output with 0.8 PF, 120 min backup using SMF battery

Supplying,installation,testing and commissioning of pressure die cast powder coated aluminium alloy housing frosted PC diffuser, IP65/IP66 protection with built in LED of the following landscape luminaire(POST TOP) suitable for 38mm dia post top mounting applications including connection with 2.5 Sq.mm. 3 core PVC insulated round copper conductor as required and as directed by the department.*PHILIPS POST TOP CODE NOS.BGP161LED2500/NW PSU 220-240V 7043 IN & BGP161LED2300/NW PSU 220-240V 7043 IN.

Supplying with erection of 50mm dia. 3.0 mtrs. length G.I. pipe medium (TATA / NEZONE make) as a garden & parking light pole with 250mm x 250mm x 3mm MS Base plate for Post top lantern complete with 400mm x 400mm x 750mm deep Cement Concrete foundation including excavation and refilling of soil as reqd, provision for cable entry, as per direction of the department. The outer portion of the G.I. Pole is to be painted by two coats of metal primer and alluminium paint. Including complete all acessories etc. as specified and directed by the department.

Supplying including installation, commissioning of HENSEL make ENYCASE DK Thermoplastic cable Junction Boxes conforming to IP66/67 weather proof for outdoor installation with knockouts for cable entry complete as specified and directed by the deptt.

"Supplying,installation,testing and commissioning of pressure die cast powder coated aluminium alloy housing frosted PC diffuser, IP65/IP66 protection with built in LED of the following landscape luminaire(POST TOP) suitable for 38mm dia post top mounting applications including connection with 2.5 Sq.mm. 3 core PVC insulated round copper conductor as required and as directed by the department. "*LIGHTING TECHNOLOGIES ADORNIS MIN MODEL NO.A04557LD00

Supplying including installation, testing and commissioning of Water Cooled Jackson Diesel Generator set coupled to suitable alternator of 415 V, AC, 3-Phase 0.8 p.f.(la mounted on a 1) M.S. Fabricated base frame.,2) M.S. fuel tank of required capacity.,3) Residual Silencer.,4) AMF/Standard Control Panel.5) Suitable batteries with lead.,5) First fill of lube oil.,6) Acoustic Enclosure complete with all accessories as specified and directed by the department conforming to IS comprising the following Technical Specification.. (RANGE FROM 15 KVA TO 625 KV *TECHNICAL DATA CJ250D5P GENERATOR SET SPECIFICATIONS 250/200 3. No. of Phases. 3 phase. 4. POWER FACTOR 0.8 LAG JACKSON ENGINE SPECIFICATION. 1. make). Cummins 2. Model. 6CTA-8.3-G4 3. No. of Cylinders. 6 4. Aspiration. TURBO CHARGED AIR TO AIR COOLED 5. Cooling. Water Cooled. 6. Governor. Electronic 7. Battery Capacity Rating. 2x12 Volt. 8. FUEL CONSUMPTION LTR/HR @ 75% LOAD 40.8 ALTERNATOR SPECIFICATION. 1. make). CGT (STAMFORD) 2. Voltage Regulation. +/- 1.0% 3. Insulation. Class - H. 4. Standard Enclosure. IP 23 5. No. of Phases. 3 *WITH AMF CONTROL PANEL

Supplying, fitting and fixing of occupancy sensor of the following categories as per required and directed by the department. (ABB/ SCHNEIDER/ MK/ ANCHOR/PANASONIC or equivalent make as approved by the Deptt.) Presence detection system with 360 degrees angle of detection with sensor head power unit and cable 2 relays, range up to 4 metre. at 2.5 metre ceiling height

Supplying, fitting and fixing Argus 220 degrees electronic movement detector for outdoor ceiling mounting, maximum range up to 12mtr. IP55 protection

Supplying, fitting and fixing of surface mounting, housing for sensor with

Supplying, fitting and fixing of mounting bracket for Argus 110 and 220 degrees electronic movement sensors

Supplying, fitting and fixing of flush/surface mounting dual load 360 degrees PIR 0-10V analogue dimmable sensor with remote

Supplying, fitting and fixing of IC Astro(Astronomical time switch with module width 2.5 (18 mm/module)

Supplying, installation of LAN works accessories as directed and specified and directed by the Deptt.*APW Cyber Rack Server Rack 18U 600X1000mmD Server Rack with Front Glass Door and Rear Perforated Steel Door with Locks. "PDU 6*5/15A - 01 Nos. Fan 90 cfm 230V - 01 Nos. Mounting Hardware (Set of 10) - 1 Set 19"" 1U Cable Manager - 1 Nos. Support Stud - 4 Nos."

Supply, installation testing and commissioning of following LAN networks equipments.*Solid Copper Cable Cat 6, 4 pair, UTP - 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation testing and commissioning of following LAN networks equipments.*APW Cyber Rack Server Rack 24U APW President Enclosure, 600mmW CYBERACK 24U / 1000mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with following items: - Top cover with cable entry -1no. - Bottom cover with cable entry -1no. - 19” Mounting Angles – 2 pairs. ,Finish : Powder coated to 80 microns; Matt finish. colour : BLACK with , Load rating capacity -- 500 kgs., Front side vented glass door and rear full perforated steel door with locks. "PDU 6*5/15A - 01 Nos. Fan 90 cfm 230V - 02 Nos. Mounting Hardware (Set of 20) - 1 Set 19"" 1U Cable Manager - 1 Nos. Castor with Brake - 2 Nos Castor without Brake - 2 Nos."

Patch Panel Cat 6 UTP Keystone -24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation testing and commissioning of following LAN networks equipments.*Patch Cord Cat 6 UTP Gray 2m - Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation testing and commissioning of following LAN networks equipments.* O. F. Cable 6F Loose Tube ( Unitube ) Type CSTA SM SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation testing and commissioning of following LAN networks equipments.*PIGTAIL SC mm (62.5um) SIMPLEX LENGTH- 1m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation testing and commissioning of following LAN networks equipments.*Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation testing and commissioning of following LAN networks equipments.*DIGILINKL/ LEGRAND OR equivalent 24 Port 10/100/1000Mbps Layer 2 stackable Switch with 4 Gigabit Combo Ports

Supply, installation testing and commissioning of following LAN networks equipments.*DIGILINKL/ LEGRAND OR equivalent 1000Base-LX SFP Transceiver LC type

M/S CAPITAL OVERLAYS