PROVN OF INSTALLATION OF HIGH MAST SECURITY LIGHT AND SPL REPAIR OF 06 X TURBO VENTILATORS AND LED FLOOD LIGHTS ALONGWITH REWIRING AND FITTINGS AT BLGD NO TN 583 AT NAGROTA MIL STATION UNDER GE NAGROTA

Amount

SCHEDULE A PART-I : Design, fabrication,Supply , errect, testing and commissioning of 16 meter high mast post of steel in two/three sections suitable for 55 m/sec wind speed as per IS:875(Part-II) totally hot dipped galvanized as per S 355 grade as per BS-EN 10025 with elevating/lowering platform type of tickness 3 mm at bottom & top of high mast pole and diameter at top not less than 150 mm and bottom not less than 360 mm & 20 side polygon standard for galvanisation as per BS EN ISO 1461 including opening at door at base of size with 1050 x 225 mm base plate of not less than 560 mm & thickness 25 mm suitable for mounting 8 Nos floodlight x luminaries in symmetrical arrangement including 450 mm dia luminaire carrage made of 40 NB ERW class B MS pipe welded in 2 sections and electrically operated raising lowering system comprising double drum winch, two continuous 5mm dia steel wire rope made of AISI 304, 7/19 of breaking capacity 1450 Kg , trailing cable of size 3 core 2.5 sqmm , connector, Integral power tool motor of capacity not less than 0.75 HP single speed one number, manual handle, junction box,lightning finial, lantern carriage, top pulley arrangement complete including design and construction of shallow foundation with approved manufactures Drawing with all matarial and labour, foundation bolt manufactured from special steel along with nuts, washer, anchor plate and commom template ,power cables from Panel to top of High Mast cg mounting clamps and bolts,including errection and commissioning including earthing as per BIS and modern engineering practices including providing and fixing of lightening arrestor and LED type single dome aviation obstruction light complete all as specified .

Supply, installing, testing and commissioning, factory made LT feeder pillar box , outdoor type, platform mounted, suitable for 415 volts 3 phase 4 wire, 50 Hz AC supply system, having bus bar chamber with insulated Aluminium bus bars 100 Amps rating installed on porcelain insulators. The panel shall be dust and vermin proof, IP 65 class protection and made of 3.15mm CRCA MS sheet and 40x40x6mm thick angle iron frame work, externally powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer on inside, front & rear opening type, with aprons for cable entry, with double door shutter and locking arrangement also with internal wiring 2.5 Sqmm with PVC insulated, solid copper conductor, FRLS cables, IS-694 marked of adequate size. The scope of work includes the following:- Incoming :- (i) MCCBs TPN, 415 Volts grade, 63 Amps rating and 16 KA rupturing capacity : 01 No for incoming.(ii) Indicating lamps : ­­ 01 set of three. (iii) Digital Timer switch with suitable size MCB & Contactor for automatic ON/OFF switching - 01 No. (iv) Luminaire carriage raising/lowering Push Button . Note : - The rate quoted by the contractor is inclusive of Excavation, PCC Foundation , plastering etc. for errecting the Panel complete.

S&F of 180 W LED Flood light luminaire made up of pressure die cast aluminium housing confirming IP-66 . The driver used is specially design to have built-in-surge voltage, open/short circuit protections. Built-in-surge protection upto 5 KV and external surge protection upto 10 KV provided for additional safety. The LEDs used in Flood light shall have CCT of 3000- 6500 K with CRI of > 70. The LED Flood light shall be integral type . The input voltage range shall be 140V to 270V.The LED driver shall be of isolated type with constant current constant voltage topology to ensure optimum driving of LEDs. The LED flood light shall have luminous of >120 lm/watt and power factor more than 0.9 with THD less than 10% complete all as specified and directed.

Supply laying , connecting & testing complete cable XLPE insulated screened PVC bedded galvanized steel strip wire armoured electric power cables heavy duty with standard aluminium conductor,1100 volts grade,cross sectional area 4 core 16 Sqmm .omplete all,as specified & directed

Supply laying , connecting & testing complete cable XLPE insulated screened PVC bedded galvanized steel strip wire armoured electric power cables heavy duty with standard aluminium conductor,1100 volts grade,cross sectional area 35 Sqmm 3.5 core complete all as specified & directed

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point /Panel as specified and testing on completion complete all as directed.

M&L for Earthing complete with galvanised mild steel earth plate electrode 60cm x 60cm x 6mm thick, burried directly in ground prefarably in vertical position (Earth pit not less than 2.25 mtr below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 25x4 mm by means of bolts, nuts, check and washers of galvanised iron including pit of PCC (1:2:4) type B-1, pre cast RCC cover slab of size 550x550x75 mm, XPM reinforced not less than 1.60 Kg/Sqm with suitable built in handle made from 12 mm dia MS round bar, excavation and earth in any type of soil., 20 mm dia bore medium grade galvanised iron water tubing fixed with cast iron funnel and wire mesh at one end, 15mm bore light grade galvanised iron protection pipe for earth lead wire upto 5 m length, charcoal, common salt complete all as shown in electric plate No 3 of SSR 2009 Part I connected to equipment, testing on completion, complete all as specified and directed.

Supply and lay GI tubing, light grade, 40 mm bore dia as cable protection fixed on walls/pole by using suitable size clamps, nuts, bolts etc. or laid in trenches complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil.complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.complete all as specified and as directed.

Removing excavated material n exc. 50m and depositing where directed. at a level n exc. 1.5 m above the starting point.complete all as specified and as directed.

M&L for Sand cushioning to under ground cable laid in trenches for laying of LT UG cables 8 cm depth before laying the cable and 15 cm after laying of cable as per MES SSR Part-I (2020) all as specified and directed. Note: Punned thickness shall be measured and paid to the contractor.

M&L for well burnt bricks , laid flat ( old size) sub class B designation '75' for cable protection abutting each other complete all as specified and directed.

Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custedy for taking credit all as specified and as directed

Taking down ceiling fan/Wall mounting fan any sweep, removing blades ,cleaning the fan completely for dust and dirt, oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20 mm dia medium grade ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories for modular switches/ socket etc. with and including 1.5 sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly for One light point / fan point / bell point controlled by one switch 5 Amp complete all as specified and directed. .

All As per Srl item N0 16 above but for one socket out let 5 Amp controlled by one switch on same board with other switch .

All As per Srl item N0 16 above for one socket out let 5 Amp controlled by one switch on independent board with other switch .

All as per item No 16 above here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independat board.

S & F Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified and directed. .

S & F Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified and directed. .

S & F Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified and directed. .

S & F Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified and directed. .

S & F Modular white cover plate incl Modular base frame/boxes & powder coated Modular sheet metal concealed box for 6 module complete all as specified.

All as per Item No 24 above but 3 module complete all as specified.

All as per Item No 24 above but 2 module complete all as specified.

All as per Item No 24 above but 8 module complete all as specified.

All as per Item No 24 above but 12 module complete all as specified.

S & F Modular blanking plates 1 module complete all as specified.

S&F of ceiling rose 3 terminal complete PVC/Polycarbonate isolated boly complete all as specified and directed.

S&F for lamp holder PVC/polycarbonate type with back plate including 10 Watt LED Bulbs suitable for batten fittings complete all as specified and directed.

Supply and fixing white / cool white / warm LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S & F LED light fitting 1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed.

S & F Rooftop Turbo Air Ventilator made of Stainless Steel, Non power driven, Colour - as per site requirements complete all as specified and directed.

S&F building security light luminaries eenergy saving and envirnment friendly long life LED light of 25W made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistanve of IK07, including MS Bracket light grade 25 mm dia, 1.2 m long bend in shape fixed on wall having an angle 120 degree, fixed with and suitable size nuts, bolts and washers etc including taking down of existing light fitting complete all as specified and directed.

S&F sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete incl taking out existing UNSV DB with MCBs.complete all as specified and directed.

S&Fin replacement of sheet metal enclosure double door for distribution board factory made for MCB DB load link Vertical TPN 4 way suitable for MCCB as incomer, 125 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar including 125 Amp MCCB as incomer 16 KA complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed.

S&F Supply and fixing wall mounted busbar chamber 415V, 3 Phase 4 wire, 50Hz AC supply system fabricated from stainless steel with 3mm thick for outer cell TPN aluminium busbar of cap 100 Amp 4 pole 8 ways complete all as specified and directed

S&F MCB SPN 40 A to 63 A 10 KA 240 volts "C" series complete all as specified and directed.

S&F MCB single pole 5 to 32 Amps 10 KA 240 volts "C" series complete all as specified and directed.

M&L in replacement of sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked minimum 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 sq mm as earth continuity conductor connected to commen earth and earth dolly complete ,all as specified and directed.

Supply and fixing in repair of aluminium strip 25 x 3.15 mm with saddles and fixing screws etc, for roof conductors and down conductors above ground, complete all as specified and directed.

S &F Air termination, sigle pointed aluminium rod 12 mm dia and 300 mm long complete all as specified and directed by Engr-in-Charge.

Supply and fixing test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 Nos 8 mm dia 25 mm long hexagonal, head screw complete all as specified and directed by Engr-in-Charge.

Azurite Engineering (BID ID -3203849)

UNITED ENGINEERING CORPORATION (BID ID -3198408)

M/S PRAJAPATI ENGINEERS (BID ID -3198303)