SPL REPAIR TO OR MD ACCN OF BLDG NO. P-72, P-227, P-228, P-229, P-198 AT COD LINE (20 QTRS) AND P-36, P-164 AT ME LINE (10 QTRS) OF 19 BIHAR UNDER GE(NORTH) DELHI CANTT-10

Amount

Taking down chowkhats or frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) all as specified and directed.

Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) all as specified and directed.

Dismantling of brick tiles, terracing tiles, single layer from roof laid, bedded and pointed in any mortar all as specified & directed.

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof).

Demolition of reinforced cement concrete (Reinforcement cut as required to facilatate demolition) of any description and in any position not otherwise specially provided

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Roughening surfaces of old concrete floor or brick wall by picking sweeping clean and washing down with water to remove dust, etc

Dismantling of floor of size not exceeding 1.50 Sqm mtr for water closet or bathroom and removing out the cinder/concrete from sunken portion, , grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 40 mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 1.50 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

Dismantling of floor of size exc 1.5 Sqm and not exceeding 5.00 Sqm mtr for water closet or bathroom and removing out the cinder/concrete from sunken portion, , grinding any sharp edges etc all as specified and directed with following: (a) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc. (b) M&L for a glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal-107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika® Fab-I and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or Pidilite. (c) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with Sika ® Plastocrete plus as specified. (d) M&L for providing 40 mm dia GI pipe spout projecting at least 150 mm beyond outer face of wall. (e) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed. (f) The area of Each WC portion is n.exc 4.00 Sqm each. (g) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. (h) 72 hrs Ponding test shall be carried out for sunken treatment before payment.

M&L for lean concrete 1:5:10 with 40mm graded stone aggregate in sunken of gauge deposited spread and levelled in layers n exc 15 cm thick hand rammed to a true surface

M&L for ceramic coloured digital tiles 8 to 10 mm thick area of 600 x 600 mm as in floors over 15mm thick screed bed in cement mortar 1:4 set and jointed in neat cement slurry and pointed in coloured cement. all as specified and directed Note- Contractor may use vitrified tile instead of ceramic tile of same size without any financial effect.

All as per Sr Item No 12 here in before but in vertical surface as skirting, dado and risers to steps over and including10 mm thick rendering/backing coat in cement mortar 1:3 etc.complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors over 15mm thick screed bed in cement mortar 1:4 set and jointed in neat cement slurry and pointed in coloured cement. all as specified and directed

M&L glazed ceramic coloured digital tiles in vertical surface 450x350x7 or 450x300x7mm thick with highlighter set and jointed in neat cement slurry and pointed in white or coloured cement to match incl rendering 10mm thick in CM (1:3) and finished rough, complete all as specified & directed.

M&L 18 to 20 mm thick machine cut pre-polished Kota stone slab including 15mm thick screed bed in cement mortar 1:4, laid over cement slurry @ 3 Kg/Sqm and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge of slab complete all as specified and as directed. (Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size in flooring and full length single piece in steps, except the location where the balance portion remain less than size as specified above).

M&L 18 to 20 mm thick machine cut pre-polished Kota stone slab including 10 mm thick rendering in cement mortar 1:3, and jointed with grey cement slurry mixed with pigment to match with shade of slab including molding the edge where as specified and as directed. (Note:- The size of Kota stone slab shall not less than 550 mm x 550 mm cut size as in flooring and full length single piece in steps, except the location where the balance portion remain less than size as specified above).

M&L Granite 20mm thick jet black ( of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed of granite over 15mm thick screed bed in cement mortar 1:6) all as specified and directed

M&L Granite 20mm thick colour as approved ( of any type) work (table rubbed and polished) in for wall lining (veneering to wall) 10 mm thick in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed of granite complete all as specified.

M&L for Reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in chajjas complete all as specified. (reinforcement to be measured separately).

M&L Reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified. (reinforcement to be measured separately).

Mild steel TMT bars 10 mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

Formwork to sides and soffits of slabs n. exc. 200 mm thick and similar works rough finished surfaces of concrete complete all as specified.

Use and waste of formwork to chullah hoods, chajjas, throughs and similar items including edges complete all as specified. .

M & L Brickwork with subclass 'B' Brick straight or curved on plan exc 6m mean radius, built in, built in cement mortar 1:6 complete including demolition of the the brick work at any position all as specified.

All as per Sr Item No 25 here in before but except brick complete all as specified.

Taking down existing cement or grit plaster any thickness including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers i.e.. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) mixed with WPC @ 2% by wt of cement finished even and fair etc complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:6 on internal brick/concrete wall surfaces of any description, and finishing the surfaces even and fair without using extra cement complete all as specified and directed .

M&L 5 mm thick rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even and smooth complete all as specified.

M&L for Preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified.

M&L for Preparing old decorated plastered surfaces of ceiling and applying one coats of white wash complete all as specified.

M&L for preparation of the newly plastered surfaces of walls applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Oil ound Distempering with, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for preparation of old decorated surface (plastered or unplastered) of walls by complete removal of existing treatment by mechanical grinder and applying cement base wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats Oil Bound Distempering, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for preparation of the newly plastered surfaces of ceiling applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two coats of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of priming with chalk whiting, on plastered surfaces preparatory to distempering complete all as specified.

M&L for complete removal of existing treatment of wall including cornices etc. by washing, rubbing down and stopping holes, and applying two coats of cement base paint of approved shade complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided all as specified and directed

S & F for steel gate made of steel section, MS sheets grill work including holdfast, 2x pintels hinges, stoppers, bushes, and all as CI decorative pieces, locking arrangement etc complete all as specified and directed.

Supply only integral water proofing compound complete all as specified..

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified..

All as per Ser Item 41 here in before but 20 mm dia bore.

Supply, laying and fixing of CPVC pipes SDR 11 of 20mm outer dia & plain CPVC SDR 11 fittings, on wall/ceiling or laying in floors complete, incl CPVC fittings (Elbow, Tee /MTA/MBTA , FTA/FBTA, Tank Adopter, Union etc suitable for 20mm bore bath fittings ). Note: - length of CPVC pipes incl fittings shall be measured for payment, no extra payment shall be made for fittings.

Supply , laying and fixing of CPVC pipes SDR 11 of 25mm outer dia & plain CPVC SDR 11 fittings, on wall/ceiling or laying in floors complete, incl CPVC fittings (Elbow, Tee /MTA/MBTA , FTA/FBTA, Tank Adopter, Union etc). Note – length of CPVC pipes incl fittings shall be measured for payment, no extra payment shall be made for fittings).

Refixing only old 20 mm dia bore steel water tubing & connection in new or old position fixed to wall, ceiling or laid in floors including necessary cutting & making of new threads for fixing of new fittings such as elbows, tees, sockets, union, , reducer, etc as required including taking up or down steel tubing and connections complete all as specified.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double alyered hoisted and fixed in position including connecting up pipes including dismantling of PVC water tanks complete all as specified.

S & F in repair 20 mm Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

S & F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic wall, screwed for iron pipe and fixed for 25 mm bore size (Minimum weight 210gms), complete all as specified.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore including demolition/taking down PVC/CI drain/Rain water pipe complete all as specified.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110 mm bore including demolition/taking down PVC/CI drain/Rain water pipe complete all as specified.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 75 mm bore including demolition/taking down PVC/CI drain/Rain water pipe complete all as specified.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, 110 mm bore including demolition/taking down PVC/CI drain/Rain water pipe complete all as specified.

S&F PVC (SWR) bends any radius, 75 mm bore, complete all as specified.

S&F PVC (SWR) bends with access door any radius, 75 mm bore, complete all as specified.

S&F PVC (SWR) bends any radius, 110 mm bore, complete all as specified.

S&F PVC (SWR) bends with access door any radius, 110 mm bore, complete all as specified.

S&F PVC (SWR) junction single (single T), equal or unequal, with access door 75 mm bore, complete all as specified.

S&F PVC (SWR) junction single (double T), equal or unequal, with access door 110 mm bore, complete all as specified.

S&F PVC (SWR) branch piece, double (double Y) equal or unequal of 110mm bore complete

S&F PVC (SWR) vent cowl, 110 mm bore complete all as specified.

S & F in repair Stainless steel plate rack (utensil rack) of size (600 mm x 750 mm) and depth 250 mm made with 0.63 mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts complete all as specified.

S&F in repair CP towel ring of 200 mm dia complete all as specified.

S & F in repair Soap dish disc (oval) type, mild steel chromium plated of approximate size 100 x 50 x 10 mm, complete all as specified.

S & F in repair sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass self 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified..

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate mix with WPC complete all as specified and as directed.

S & F in repair stainless steel sink with drainage board, made out of 1.00 mm thick sheet with plug, washers, waste coupling and pipe, cast iron cantilever brackets, connecting union over all size 915 mm X 460 mm with bowl size 410 mm x 330mm x 160 mm complete all as specified.

S & F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges complete all as specified.

S & F in repair Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15 mm bore complete all as specified.

S&F in repairs bib tap with crutch or butterfly handle, quarter turn screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified

S&F wash hand basin mixer 15mm dia CP brass fancy type including joints to steel pipe or unions all as specified.

S&F 15mm dia chromium plated quarter turn wall mixer hot & cold L bend 3 in 1 pattern fixing and connection to pipes, complete all as specified and directed.

S&F Kitchen sink mixer 15mm dia CP brass fancy type including joints to steel pipe or unions all as specified.

S & F in repair Brass chromium plated shower rose 65 to 90 mm size with swivel joints, including Stainless Steel shower arm with wall flange complete all as specified.

S&F in repair 10 litre capacity PVC low level flushing cistern with dual flush type‘ white’ with inlet, float valve including bracket with 32mm dia PVC waste/flush bend pipe appx 600 mm long complete all as specified.

S & F in repair PVC connection 600mm long and15 mm dia with brass fly nut at both ends complete all as specified.

S&F in repair vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest including 'P' or 'S' trap and provn of cement concrete bedding, outgoing flushing pipe, anti syphonage pipe etc complete all as specified.

S & F vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia CP brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete all as specified. Note :- Pillar tap shall be measured as supply only under respective item

S & F 32 - 40mm dia bore Low density polyethylene pipes (LDPE)of pressure rating 6kgf/cm2 fixed complete to walls, ceilings or in floors etc for WHB complete all as specified.

S&F in repair Chromium plated brass stop or angle valve quarter turn for 15mm bore pipe, fixed in repairs complete all as specified and directed.

S&F Factory Made double rebated extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: For WPC solid door/windows frames, (-) 5mm tolerance in dimension i.e. depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made ,

S&F Pressed steel frames of size/section for doors of section 105mmx60mm with one or more rebates including necessary fixing lugs, 3 x hinges of 100mm , lock strike plate, complete, as specified,

M&L for plain cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as in back fill in pressed steel door frame etc all as specified and directed.

M&L for Plain cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate as in fixing of hold fast of door frame in wall all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm single side prelaminate PVC sheet used instead of plain colour PVC Sheet suppling & fixing in opening as per specification & drawing.

Factory Made Solid PVC Moulded Door Shutter with hard core black board, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelaminate sheet colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing in SSR complete all as specified.

S&F 30mm thick Factory made wire mesh solid WPC door shutter consisting of density 650 Kg /Cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm x25mmx2mm and 32mm long steel screws drilled suitable to pass through Other hardwares should be fixed with 19x6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. Note: Fixture/fittings shall be measured & paid under relevant item .

S&F 35 mm thick factory made flush shutter solid core construction with block board core and plywood face panels commercial type on both sides. Flush shutters shall have teak wood edging as specified in IS complete all as specified..

S&F for steel windows fabricated from roll formed sections made of galvanized steel colour coated powder coated (Base steel as per Sqm IS-513 D quality galvanized as IS 277 with zinc coating of 120 GSM with total coated thickness of 0.60mm. The coated section shall be with primer coated of primer of -7 microns thick, finish painted with a polyester paint of 12.16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick with the following specifications (a) Main frame 72mm x 55mmx0.58mm (b) Mullion 72mmx50mm x0.58mm(c) Glazed/gauzed shutter frame 47mmx20.20mmx0.58mm (d) Glass beads size 12mmx12mmx0.58mm Accessories. Each shutter shall be provided the following fittings (a) Stainless steel pipe of hinges 01 set (b) Aluminium powder coated handle-04 Nos. Glass panes Glazed shutter and fixed glass provided with glass of 5.00mm thick float glass. Wire Mesh -Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperture 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate. Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw. Note: The glazed/Gauzed shutter including guard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive of all aspects as specified in Drg No- CEDZ/TD/289 sheet 1 R/2 and 2R/2..

S&F Rolled mild steel sections conforming to Gde Fe-290-0 or Fe-165 as in coolar stand fixed in position, clamps etc similar work complete all as specified.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, fixed with stainless steel wire staples or wooden beads, tinned tacks to wooden doors shutters complete all as specified.

Taking down/dismantling old particle board or any board kitchen cabinet , wardrobe including all assessary fittings and fixtures complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen & Cabinets.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets.

S&F magnetic catches with steel body ‘H’ type, fixed to shutter complete all as specified.

S&F Brass handles,100mm long cast type, polished bright complete all as specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified.

S&F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floor of size 140 mm complete all as specified.

S&F 4 levers brass cupboard locks grade-I, size 65 mm complete all as specified.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified.

S&F butt hinges, 100 mm size medium weight, Staniless steel complete all as specified.

S&F aluminium handles 125 mm size cast type, anodised complete all as specified.

S&F aluminium handles 150 mm size cast type, anodised complete all as specified.

M&L sliding door bolts stainless steel, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S&F Stainless Steel tubing 25mm dia grade 304,Sch 5 for curtain rod fancy type including fancy type CP brabs brackets (wall to wall or flush to wall) with finials or end caps decorative type as approved by GE for securing to curtain rod to wall in position, fixed in repair complete all as specified.

M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified.

M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation complete all as specified.

M&L cement concrete type C-1, 1:3:6 (using 20mm graded aggregate) as in plinth protection and paving 50 mm thick laid in slope finished even and fair without using extra cement incl making joints at every 2.5m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight including necessary form work and complete all as specified.

M&L cutting crack to 'V' groove section in existing roof cleaning out wetting grouting with cement and sand slurry of 1:3 complete all as specified and directed.

M&L for cement concrete 1:2:4 type B0 (using 12.50 mm graded stone aggregate) as in levelling coarse over RCC slab to bring the desired slope up to six storied Bldg, using water proofing compound @ of 2% by weight of cement complete all as specified & directed. Note:- Water proofing compound shall be measured and paid separately.

M&L for APP based polymeric membrane plain finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints over accessable roof tip.

M&L for APP based polymeric membrane plain finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints over non accessable roof top. (ii) Again applying hot bitumen 85/25 @ 1.2 Kg per Sqm over water proofing membrane. (iii) Dusting dry sand @ 0.75 Kg per Sqm and applying two coat of bituminous aluminium paint @ 0.10 Kg/Sqm over the membrane.

S & F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner.

M&L for followings :- (i) Removing plaster & finishes all around the columns, slabs & beams (on all four side of column to full height , three side of beam to entire span & bottom of slab to area as directed) (ii) After cleaning gently removing cover concrete using pneumatic/electric chipper or any other approved tool in entire portion of structural member (removal of cover concrete shall be done to an extent when reinforcement is visible) (iii) Removal of cover concrete with under cutting of up to a depth of 20mm beyond reinforcement around full circumference & full length of bar where directed. (concrete shall be stripped to an extent concrete substrate is exposed) (iv) Cleaning exposed concrete substrate by using water jet. (v) Removing visible rust along the length of reinforcement using hand tools as approved. Supply & applying of rust removing chemical to remove rust from existing reinforcements. (The Engr-in-charge may order sand blasting if rust is visible) (vi) Any other work as directed by Engr-in-charge to present clean surface for determination of type of repair to be carried out complete all as specified and directed.

M&L for providing rust proof /anti corrosive treatment to bars :- (i) cleaning of all exposed bars (new & old) alround (ii) Apply a single coat of Alkaline rust converting primer on alround bars new & old as recommended by the manufactuer (iii) Apply two coats of Epoxy phenolic anti corrosive protective coat on bars alround new & old as recommended by the manufactuer. Note : Anti corrosive treatment shall be continuous espcially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating.

M&L for providing PMM (Polymer modified cementitious mortar) :- (i) Dry sub strata surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairly rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufacturer complete all as specified and directed.

M&L for treatement of cracks found in the core concrete :- (i) Opening of crack by making a ' V' notch/groove of size 12mm x 12mm over the entire length of the crack as identified by the Engr-in-charge. (ii) cleaning ' v' notch/groove of all dust/debris/loose material (iii) Drilling hole of 16mm dia and about 40mm deep along the length of crack @ (300 mm c/c or thickness of structural member whichever is less) Note : In case length of crack is found less than 300 mm then min 2 holes shall be drilled. (iv) Inserting 12 mm dia flexible PVC one way injection nipple in the hole drilled above and fixing the nipple with the help of fast setting epoxy putty. (v) Seal the surface around the nipple and the area of crack between successive nipples polymer modified mortar to ensure that there is no leakage from any gap. (vi) Allow the polymer modified mortar to cure for 24 hours and ensure that firmly fixed in postion. (vii) Cleaning nipple one by one commencin from the top to bottom in case of column and one by one in alternate direction incase of beam/slab using blow compressed air followed by water injection. An Ensuring that there is no obstruction in free flow of grouting materials complete all as specified and directed. (viii) Injecting " resin with very low viscosity monomer by mixing resin and hardener in proportions recommended by manufacturer by using injection gun equipped with pressure gauge & valves for controlling of flow of compressed air & resin. Note:- pressure shall be in the range of 1-2 kg/Sqm and shall be done in nipples one by one as per order recommended by manufacturer. Mixing of resin and hardenere shall be mixed in small quantities so as it is consumed with in 30 minutes. Before use mixer shall be stirred thoroughly. (ix) Allow entire effected surface to cure for 24 hours. (x) cutting out projected parts of the nipple & seal the hole in the nipple with epoxy putty as recommended by manufacturer. (xi) cleaning exposed surface complete all as specified and directed.

S&F 12mm dia steel sheer connector in grid pattern in between old core and new concrete as wherever directed by Engr-in-charge and as specifed by manufactuer including drilling hole of depth of 100 mm and chemical anchoring with pure epoxy resin anchoring complete all as specified and directed. (Note:- The cost of drilling hole &chemical anchoring with epoxy resin is inclueded in this item)

M&L for Providing & Pouring Micro concreting M-40 grade :- (I) Dry concrete substrate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above pour Micro concreting M40 grade, Make : MasterEmaco S46T of BASF or equivalent FOSROC/SIKA using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be repaired in RCC beams & columns etc,. Adding of aggregates will be permitted only as per manufacturer’s recommendation without compromising the strength. The rate shall include cost of all materials (except re-bar) labour charges for mixing, pouring concrete, cost of tools, lead & lift of materials, transportation etc., to carry out the complete work complete all as specified and directed including M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. The cost of micro concrete M-40 grade & Epoxy bond coat is included in this item.

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 8 mm dia bar - drilling length 80 to 100 mm Note : Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete all as specified and directed. Note:- The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item

M&L for Drilling & chemical anchoring of new rebars/stirrups :- (i) Drilling in to the sound RCC members for anchoring of rebars/stirrups as directed, the dia of hole to be match with dia of rebar & length of drilling as under :- 16 & 20 mm dia bar - drilling length 160 to 180 mm Note:- Anchoring of new re-bars of any dia as directed in to the sound RCC members as directed using pure epoxy resin anchoring mortar with appropriate diameter of drilling of holes as mentioned above for proper bonding into the concrete etc., complete all specified and directed. (The cost of drilling hole & chemical anchoring with epoxy resin is inclueded in this item)

M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note:- Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

S&F for stengthening existing reinforcement by use of mild steel bars of any dia , cut to length, bent to shape required, including cranking, bending spirally and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete as directed at site Note :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guniting is done with polycretes admixture @ 2% by weight of cement all as per manufacturers instructions (polycretes admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

M&L for cement concrete 1:4:8 type D- 2 (40mm graded stone aggregate) as in sub base, hard standing of 75 mm thick, complete all as specified

M&L for Sand filling (sand cushioning) under floors or in foundations including watering and consolidations complete all as specified and directed”

S&F machine pressed precast concrete rubber moulded interlocking coloured (Red and Yellow) paver block of approved pattern shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade

M&L for rubber moulded coloured cement concrete Chequered tiles 300mm x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed

S&F fibre glass reinforced translucent corrugated sheeting 2 to 3mm thick with two corrugations side lap fixed with coach screw and washer in roof, wall etc, complete all as specified and directed

S&F steel work in tubular trusses, Rafters and purlins including special shaped washer etc. complete using washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed

Excavation in post holes (or similar notes each) n.exc 0.5 Cum getting out, returning, filling in and ramming earth or broken rubbles mixed with earth around in layers n.exc 25 cm in soft/loose soil, complete all as specified and directed

M&L for Cement concrete 1:2:4 type B-2 using 40mm graded stone aggregate in foundations, filling and mass concrete to fix post , complete all as specified and directed

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineerin- Charge. (Note: Fitting/ Fixtures shall be paid separately under relevant item)

Cutting shrubs, wild growth, plants not exc 30cm girth grown on permanent structures and removing same from roots and stopping the recurrence by injecting herbicide Glyphosphate 4+ solution (04 % concentrate) into plant root to eliminate further growth. Application shall be as per manufacturer instructions. The disturbed area shall be repaired with PCC (1:2:4) Type B-0 mix and surface finished even and smooth in CM 1:4 incl applying two coats of matching finish of adjacent area. Minimum plant in each block is 10 Numbers

Description of Work / Item(s)

Amount

Taking down carefully copper / aluminium point wiring (light / fan socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc for taking credit including making good the disturbed surfaces to match with the existing complete all as specified and directed

M&L for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall on wall including sunk zinc coated pressed steel terminal box of 1.60mm thick with 3mm thick plastic laminated sheet top cover, brass screws, cup washers etc complete all as specified and directed for One light / bell point controlled by one, one way switch 06 Amps complete all as specified and directed

All as per ItemNo 02 here-in-before but one Ceiling/ exhaust fan point controlled by one, one way switch 06 Amps complete all as specified and directed

All as per item No 2 here-in-before but for one light point controlled by two way switches complete all as specified and directed

All as perItemNo 02 here-in-before but one 3 pin, 06 Amps socket outlet point on independent board controlled by one, one way 06 Amps switch complete all as specified and directed

All as per ItemNo 02 here-in-before but one 3 pin, 06 Amps socket outlet point on same board controlled by one, one way 06 Amps switch

All as per ItemNo 02 here-in-before but point wiring with 4 Sqmm single core FRLS cables and earth continuity wire of 4 Sq mm single core FRLS cable for one 3 pin 15 Amps socket out let point controlled by one, one way switch on independent board complete all as specified and directed

S&F bell push, flush type, 06 Amps, 230 volts with switch frame complete all as specified and directed

S&F switch piano flush type, 06 Amps, single pole, one way, 250 volts complete all as specified and directed

S&F switch piano flush type, 16 Amps, single pole, one way, 250 volts complete all as specified and directed

S&F switch piano flush type, 06 Amps, single pole, two way, 250 volts complete all as specified and directed

S&F socket outlet 2 in 1, 5 pin, 06 Amps, flush type, 250 volts with socket frame complete all as specified and directed

S&F socket outlet 2 in 1, 3 pin, 06 Amps and 3 pin, 16 Amps, flush type, 250 volts with socket frame complete all as specified & directed

S&F ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 100 watts incl connection complete all as specified and directed

S&F ceiling rose, 6 Amps, 250 volts, AC, ISI marked with three equal size terminals complete all as specified and directed

Supply and fixing ding dong bell, AC, 230 volts, single pole complete all as specified and directed

S&F (in replacement) lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting including 9W LED bulb complete all as specified and directed

S&F surface and wall mounted LED batten 10 watt 2 feet long extruded aluminium housing provided for efficient heat dessipation with polycarbonate diffusser and integrated electronic drive suitable for mirror fittings, all accessories pre-wired including connecting up with twin core flat flexible copper conductor cable of suitable size including taking down of old/ unsv light fitting complete all as specified and directed

Taking down of existing u/s tube light fitting and S&F on surface and wall mounted LED batten with polycarbonate housing and initigarated electronic drive 20 Watt fixture 4 feet provided for efficient heat dissipation with policorbonate diffuser and integrated electronic driver and all accessories pre-wired including connection with twin core flexible copper conductor cable of suitable size complete all as specified and directed

S&F decorative wall mounting light SS finish fixture with textruded glass difuser suitable for up to 40 watt mini glass lamp, lamp holder, including 9 Watts LED bulb in warm white clour of 6500 K of B22 base cap and all accessories pre-wired including connecting up including taking down of existing u/s light fitting complete all as specified and directed

S&F on wall energy saving, eco friendly LED bulk head fitting 10 Watt, IP 65surface mounted with ABS body & polycarbonate diffuser, etc and all accessories pre-wired including connecting up including taking down of old/ unsv light fitting complete all as specified and directed

Taking down of exiting u/s security light fitting and supply and fixing energy saving security light fitting of 35 watts LED Versatile pressure die-cast aluminium IP 66 roadway luminaire with high power LED as light source comprising with electronic driver and all accessories pre-wired incl connecting up with PVC insulated copper conductor cable 1.5 Sqmm, 3 core and incl 40 mm bore light grade GI tube mounting bracket of suitable length, bend to shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as specified and directed

S&F Ventilating fan wall mounted type of 250 mm sweep, 230 volts, AC, 50 Hz capacity, cutting of hole in wall, making of wooden frome, all arrangements for mounting of fan including making good of disturbed surface complete all as specified and directed

M&L for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable with and including continuous earth wire of size 6 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable drawing into and including rigid non-metallic PVC concealed conduit of 20 mm dia, medium grade with all conduit accessories and connected to common earth dolly with suitable copper lugs including all cutting / chases etc in walls and making good to the disturbed surfaces to match the existing complete all as specified and directedall as specified & directed, including taking down old sub main wiring complete all as specified and directed

All as asper Item No 24 here in before but for 02 x 4 Sqmm for phase & neutral and 01 x 4 Sqmm for continuous earth wire complete all as specified and directed

Supply and fix electric water heater, storage type 25 ltrs capacity, BEE star rated, vertical type with suitable size of fastner and incl provision and connecting up of SS braided pipe with adapter for inlet and outlet water connection, copper element corrosion resistance antiscaling magnesium anode having adustable knobe for temperature control and inner tank material of superior glass lined tank and outer body material ABS with high pressure with standing capacity upto 8 bar pressure having heating element 2 KW and minium two year warranty on product, minimum three years on heating element complete all as specified and directed

S&F industrial type SPN enclosure with a two pin and earth plug and socket complete all as specified and directedwith and including MCB SP, AC, 230 volts of 20 Amps, 'B' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed

S&F (in replacement) sheet metal enclosure distribution board, single pole and neutral, AC, 240 volts, 8 way, and metal double door with IP - 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed

S&F (in replacement) sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volts, 04 ways and metal double door suitable for MCCB 100 amps as incomer and MCB SP as outgoing along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed(Note :- MCCB & MCB SP will be measured seperately)

Supply and fixing (in replacement) sheet metal enclosure distribution board triple pole and neutral (TPN), AC, 440 volts, 04 ways and metal door with IP 43 & IK 09 protection along with cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed and comprising of the following:- (a) MCB TPN 63 Amps, 10 KA, 'C' curve, 415 V - 01 No. (b) MCB, SP, AC, 240 volts of 40 Amps, "C" curve, 10 KA breaking capacity - 4 Nos

S&F (in replacement) MCCB 100 amps, 4 Pole, 415 volt, AC, fixed type, with breaking capacity 25 KA suitable for load line/ VTPN DB & connection complete all as specified and directed

S&F (in replacement) MCB, SP, AC, 240 volts of 10 to 40 Amps capacity "B" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified and directed

S&F (in replacement) MCB, SPN, AC, 240 volts of 63 Amps capacity "B" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified and directed

M&L for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried vertically in ground (earth pit not less than 2.25meter deep below ground level) with top edge of the plate not less than 1.5meter below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 75mm center to center both way with 12mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40mmx40mmx3mm frame for pit cover including testing on completion complete all as specified and directed

Taking down carefully existing unserviceable electric meter any type any make after disconnecting the electric connections and supply and fixing including Polycarbonate thermoplastic meter box with transparent hinged lid with sealing provision, internally embedded gasket of size 217 x 253 x 115 mm suitable to accommodate single phase KWH meter and connecting up including making good the disturbed surfaces all as directed by Engineer - in - charge. (Note: Old metter will be deposited in E/M Store)

Taking down ceiling / exhaust fan any make from ceiling carefully, cleaning to remove any type of sticky dust with cleaning material as required and re-fixing in its original / desired location with necessary connection incl provision of cable from ceiling rose to connector of fan after repairing, greasing, oiling, replacement of minor items such as pins, nut bolts, flexible wire etc incl spray painting with synthetic enamel paint complete all as specified and directed

BEHAL TRADERS (BID ID -3130466)

GLIBS CONSTRUCTION (BID ID -3130723)

L G BUILDERS (BID ID -3131296)

Shri Balaji Construction (BID ID -3125030)

M/S SURINDERAS CONSTRUCTION CO. (BID ID -3124482)

M/S ANIL KUMAR (BID ID -3130436)

The new hut furnitures (BID ID -3130440)

A R construction (BID ID -3130309)

CHOPRA BUILDERS (BID ID -3131506)

GLIBS CONSTRUCTION (BID ID -3130723)

The new hut furnitures (BID ID -3130440)

BEHAL TRADERS (BID ID -3130466)

Shri Balaji Construction (BID ID -3125030)

M/S SURINDERAS CONSTRUCTION CO. (BID ID -3124482)

L G BUILDERS (BID ID -3131296)

M/S ANIL KUMAR (BID ID -3130436)

A R construction (BID ID -3130309)

CHOPRA BUILDERS (BID ID -3131506)