SPL REPAIR TO BLDG NO JP-44 (JCO MESS), JP-18, JP-181 (TOILET BLOCK), SPL REPAIR/REPLACEMENT OF DAMAGE SLAB AND JOINT FILLING FOR HELIPAD AND PROVN OF HARDSTANDING WITH INTERLOCKING TILES ADJACENT TO BLDG NO 55 (ECHS) UNDER AGE B/R-I AT ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified & directed.

M&L brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with fly ash brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified & directed.

Demolition of cement concrete (un-renforced) in ground floor and paving not exc 15 cm thickness (below or above ground level) & removal of rubbish material complete all as specified & directed.

M&L 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate), 25mm thick, as in Sub base complete all as specified & directed.

M&L non skid ceramic tiles colored 300mm x 300mm x 7mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement over with and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

M&L vitrified ceramic tiles 10mm thick (square/ rectangular), polished, coloured (light shade as approved), area of each tile n exc 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L vitrified ceramic tiles 10mm thick (square / rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 10mm thick rendering cement & sand mortar 1:4 complete all as specified and as directed.

M&L machine cut kota stone slab flooring 18-20mm thick over with and including 20mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed

M&L 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc n.exc 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified & directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises.

M&L glazed ceramic coloured tiles in vertical surface 450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10mm thick rendering in CM 1:4 complete all as specified & directed.

M&L machine cut kota stone slab 18-20mm thick in steps for riser, dado, skirting, wall etc over 15 mm thick cement plaster in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

M&L 50mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in plinth protection finished fair and even complete all as specified & directed.

M&L granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types over with and including 20mm thick screed bed in CM 1:6 cement concrete complete.

Taking down cement plaster any description on brick or stone walls etc.

M&L rendering 10mm thick in cement mortar 1:6 on fair faces of brick/stone masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in CM 1:4 on brick/stone wall surfaces or other than fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound all as specified. Note : Water proofing compound shall be measured and paid separately as supply only here-in-after.

All as per item No 19.00 but 10mm thick in CM 1:3 over ceiling.

M&L rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed.

Supply only Integral waterproofing compound.

M&L preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified & directed.

M&L preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 1 mm thick wall care putty of approved tint complete all as specified & directed.

M&L applying two coat of weather coat/apex paint (exterior emulision) of approved tint over new plastered surfacess scraping, sand papering or by any other mean and preparing plastered surfaces including one coat of primer on walls etc complete all as directed.

M&L preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade /tint complete all as specified& directed.

M&L preparation of newly plastered surfaces & applying three coats of white wash on ceiling complete all as specified& directed.

M&L applying two coat of weather coat/apex paint (exterior emulision) of approved tint over old plastered surfacess scraping, sand papering or by any other mean and preparing old plastered surfaces including one coat of primer on walls etc complete all as directed.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & directed.

Complete removal of old plastered surfaces of walls applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete all as directed.

M&L preparation of old plastered surfaces & applying one coat of white wash on ceiling complete all as specified & directed.

Taking down Chowkatts or frames with shutters (without taking off shutters from the frame) n exc 1.5 sqm each & removing to store.

Taking down Chowkatts or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but n exc 4 sqm each & removing to store.

S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast.

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification.

M&L factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified & directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified & directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed.

S&F Butt hinges 100mm long medium weight, cold rolled mild steel complete all as specified & directed.

S&F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed.

S&F 150mm aluminium handles, cast type, anodised complete all as specified & directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed.

M&L preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified& directed.

M&L mild steel angle iron door frame/chowkats of Fe 410-0 (Gde-E-250) incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified & directed.

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos), suitable handle (1 No) complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc complete all as specified & as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

S&F sheet glass ordinary quality, in squares n.exc 0.5 sqm each 4.80 mm thick complete as directed.

S&F frosted/figured sheet glass, in squares n.exc 0.5 sqm each 4.00 mm thick complete as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed.

S&F in repair rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks complete all as specified& directed.

S&F in repair ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 20 mm dia complete all as specified & directed.

S&F in repair brass Gun-metal, globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed.

Taking up or down 20mm steel tubing and connections, complete all as specified& directed.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed.

S&F steel tubing medium grade 20mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed.

S&F in repair 15mm dia fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed.

S&F in repair thin rim table top basin size 480mm x 380mm x 135mm including 32mm CP waste coupling & PVC flexible waste pipe of 90cm long complete set all as specified and directed.

S&F Brass chromium plated bottle traps 32mm dia for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified & directed.

S&F looking mirror 5mm thick including cutting, grinding, polishing and chamffering of edges of glass, fixed with and including 20mm dia fancy type stainless steel fixers- 04 Nos complete fixed to wall all as directed.

S&F in repair white vitreous china wash hand basin 'Flat back' of size 550mm x 400mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as directed.

S&F in repair fancy type center hole basin mixer without popup waste system but including plain waste 32 mm size with aerator complete cast copper alloy, chromium plated, scrwed downhigh pressure, with long scrwed shanks & fly nuts scrwed for iron pipes of 15 mm bore complete all as specified & as directed.

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

S&F in repair 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed ddown high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed.

S&F in repair Stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed.

S&F in repair 15mm bore 2 way angle valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F in repair vitreous China wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F in repair Vitreous China Squatting pan, Orissa pattern, size 580mm x 440mm white with integral foot rests connection to trap and to flushing pipe, etc complete including making food to floor complete all as specified & directed.

S&F in repair PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC complete all as specified.

S&F in repair kitchen sink with drainage board made out of stainless steel 1mm thick with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or including and fixing cast iron cantilever brackets and connecting union to pipe over all size 495mm x 420mm bowl size 410mm x 330mmx 160mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified & directed.

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed.

S&F in repair glass corner shelf in 3-sets for each complete all as specified & as directed.

S&F in repair toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws.

S&F in repair towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed

S&F in repair PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors/walls complete all as specified & directed.

S&F in repair PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls/floor complete all as specified & directed.

S&F in repair PVC (SWR) bends any radius 110 mm bore complete all as specified & directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete all as specified & directed

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed.

S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed.

S&F in repair PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed.

S&F in repair Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 100mm dia bore pipe incl bolts and nuts and securing ends of stays to wall or roof complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets/AC boards, any thickness, including cover fillets and removing from site all as specified.

M&L False ceiling with ArmGyp-FB ceiling tiles of size 595mm x 595mm thickness (as approved by GE) fixed with and including galvanised iron powder coated inverted "T" or "L" section (concealed GI frame work) of mettalic or equivalent suspended from ceiling with provn of galvanised wire 4 mm dia and wall taping screw including butterfly clip, hold down clips for fixing the board to frame complete all as per manufacurers instructions all as directed and specified. (a) size of main tee 39 x 24.4 x 0.8 mm (b) size of wall angle 22.2 x 22.2 x 0.65 mm (c) size of grid 0.61 x 0.61 mm complete all as directed and specified.

S&F in repair factory made PVC shutter Cabinet of required size, fabricated by joining for 18mm thick PVC Celluca ply with prelaminated sheet on one side cut to desired size of shutter and fixed with frame as in cabinet boxes with shelf and shutter full size fitted under or above the kitchen cooking plateform incl all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc including dismantling boarding any description. Note (i) : Items like cupboard knobs, stainless steel channel, CP plate clip hinges are included in the unit rates of this item. (ii) For payment purpose, area of front elevation shall be considered.

Dismantling framed timber scantlings 40 sqcm and over in section, in any position complete all as specified.

S&F MS steel work in framed work angle/tubular trusses and tubular posts, purline, rafter including special shaped washers etc complete using but welded. RHS/SHS confirming to IS 4923 : 1997 complete all as specified & directed.

S&F expanded metal weight exc 4.0kg per sqm, cut to length, bent to shape required or mesh and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members.

S&F MS frame work such as grills, gratings, angle frame etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stands and similar work conforming to Fe 290,Gde-E-165 a coat of red oxide primer after preparation of steel surfaces complete all as specified.

Dismantling asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified & directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified or fixed with L type or J type hook bolts & washers etc complete all as specified & directed.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws as specified or fixed with L type or J type hook bolts & washers etc complete all as specified & directed

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

S&F in repair stainless steel drapery rod 25mm dia (in lengths directed) of approved colour with and including decorative bowel at both ends and pair of power coated stainless steel brackets fixed at both ends with PVC Rawl plug and steel screwed on walls/beam complete all as specified & directed

M&L PCC (1:3:6) type C2 (using 20mm graded stone aggregates) in roof kerb, rounded and chemfered edge, benching to manhole complete all as specified

S&F 50mm thick steel fibre reinforced concrete (SFRC) manhole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 3 ton /Sqm in square rectangular or Circular shape incl demolition of old manhole covers complete all as specified and directed

Cutting into existing manholes for new drains, for removing existing branch drain, making good to walling and rendering cutting out branch channel and making good benching (bore of pipe 100 mm).

M&L providing precast cement concrete louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar set in CM 1:4, type B-0, (1:2:4) 12.5mm aggregate complete all as specified & directed.

M&L plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) set in CM 1:6 as in coping of brick masonry wall kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wall in) corbels, brackets, etc including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified & directed.

Demolition mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed.

M&L PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified & directed.

M&L rendering or screed bed 15mm thick in CM 1:4 with water proofing compound over green concrete surface (WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified & directed.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces over bituminious primer complete all as specified & directed.

M&L APP based plymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M&L 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring path way etc complete all as specified & directed

M&L rubber moulded coloured chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with gray pigment cement and pigment with and including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L 40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in flooring complete all as specified & directed.

S&F glass dividing strips, 3 mm thick and 38mm width complete all as specified.

M&L providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in concrete bed for 150mm pipe including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M&L 150mm reinforced concrete pipes, class NP2, laid and jointed in CM 1:1 complete with collars complete all as specified and directed

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5 M in depth for foundation and getting out in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified.

Removing excavated material, n.exc 50M and depositing where directed at a level n.exc 1.5M above the starting point complete all as specified & directed.

M&L plain cement concrete 1:4:8 type D-2 (40 mm graded stone aggt) as in foundations, filling & mass concrete complete all as specified.

M&L cement concrete work in pavement/ hard-standing of flexural strength 40 kg/square centimetre in field using minimum 400 kg of cement per cubic metre or as per design mix, thickness of concrete 25cm or less complete all as per directed.

Add/Deduct to item above if extra/less/kg of cement used for cubic metre.

M&L preparing concrete surfaces of pavement and marking 2.5mm thick center lines, stop lines, dashes, arrows etc and the like n.exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.

M&L forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' complete incl removing old joints all as specified & directed.

M&L forming 20mm expansion joints, filled with pre-formed bituminous filler and top 30mm primed filled with sealing compound Grade A complete incl removing old joints all as specified & directed

Suface dressing n exc 15cm deep in soft/loose soil complete all as specified and directed

M&L hard core of broken stone or boulders of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L 60mm thick machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006, M-35 Grade over with and including 25mm thick sand cushion complete all as specified and directed

Taking down carefully copper/aluminium point wiring for one light /socket/power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings complete all as specified.

Taking down unserviceable DB TPN/SPN any type any capacity complete and making good to disturbed surfaces of walls complete all as specified.

M&L point wiring complete with 1.50 Sqmm single core multistranded copper conductor fire resistant low smoke (FRLS) PVC insulated and unsheathed cable 1100 volts grade conforming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20mm dia external) but shall be increased as per actual site requirement in accordance with clause No 19.125 of SSR Part-I, ISI marked with wall thicness not less than 1.8mm including conduit accessories like bends, tees, junction boxes etc fixed to concealed / recessed in wall or ceiling etc including 1.50mm thick FRLS PVC inculated unsheated copper earth wire including sunken type pressed steel terminal boxes electro plated of suitable size with bakelite white / coloured top sheet cover 3.0mm thick for one light point controlled by one way switch. Note : The quoted rate shall deemed to be inclusive of making provisions for concealed wiring if that surfaces are existing and rates shall include cutting chases, pinning and making good the surfaces to match with exising finishes complete.

All as per serial item No 130.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 130.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed. Make :- Havells Cat Part No LHEXBHP71NW018 or equivalent of Philips/ Crompton Greaves /Bajaj/Wipro.

S&F LED lights fitting 2 feet x 2 feet 33/36 watts, 220V, 6500K, Cool white, panel light with driver connecting up with three core flexible copper conductor cable of suitable size from cieling rose complete all as directed. Make : Phillips/ Crompton Greaves/Havells

S&F exhaust fan, steel body AC single Phase, 230 V of size 300mm sweep with blades and frame and louvers complete all as directed.

S&F ceiling fan complete with blades, down rods, electronic regulator and accessories, 230V 1200mm sweep minimum air delivery 210 CFM with service value 6.00 BEE 5 star rated with brushless direct current motor (BLDC) complete all as directed.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F MCB 40 to 63 Amps, single pole & neutral, 240 Volts complete all as specified and directed.

S&F MCB 5-32 Amps, single pole, 240 Volts 'C' curve, 10KA ISI marked as per IS/IEC 60898-1 2002 complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

M&L XLPE inculated, armoured heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross sectional area 10 sqmm, 2 core complete all as specified & as directed.

M/S Naglot Enterprises

shiva construction

AARSINFRATECH

KARTIK ENTERPRISES

M/S JINDAL ENTERPRISES

M/s ASK Enterprises

M/s S Amarjit Singh