CERTAIN MISC REPAIR TO STEEL AND WOODEN FURNITURE UNDER GE NARANGI

Amount

REPAIRS TO ALMIRAH STEEL LARGE WITH SHELF/ALMIRAH STEEL 1/2HX1/2S AND ALMIRAH MEDIUM [DRG NO: [(FD-67M, 1031, FD/E6/MAP/18 & 1032 ) ]

Replacement of existing unserviceable handle by providing new Mild Steel chromium plated handle of standard size including nuts and washers of Almirah large/medium steel best quality as approved all as specified and directed.

Supply and fix new 75mm 6 lever lock with two keys set fixed with suitable screws, welding as required for Almirah large/Almirah 1/2Hx1/2S and Almirah Medium steel incl removing the existing unserviceable lock. Make: Godrej/Harrison/Link

Supply and fix new steel cleats for supporting shelves inalmirah large/almirah 1/2Hx1/2S and almirah medium steel incl removing the existing unserviceable cleats complete all as directed.

Removing unsv 3 way locking device from alimarh large steel and fixing new locking device all as specified

All as per item No 1.04 here-in-above but of almirah medium steel.

Material and labour for welding by gas welding wherever required complete all as specified and directed. Welding at one point will be measure as one unit

Preparation of old painted surfaces of Almirah large steel internally and externally including shelves (Top & bottom) by No 50 sand paper and wire brush. Applying putty on the patch and rubbing with sand paper No 150 to make surface even Thereafter applying one coat of red oxide primer and applying two coat synthetic enamel paint by spray painting of approved colour all as specified and shown on drawing.

All as per item No 1.07 here-in-above but for Almirah medium steel.

All as per item No 1.07 here-in-above but for Almirah steel1/2 Hx1/2S

REPAIRS TO BED HARD TOP STEEL [FD/MAP/E6/08(R) ]

Removing the unserviceable plywood from bed hard and tightening all legs ,long rails and short rails of bed hard top Steel complete all as directed.

Removing the old welding spots from broken welding joints and re-welding in the same place as required. Preparation of old surface by sand paper No 50 and wire brush and apply black paint on compete bed all as specified and directed.

Supply and fixing new 12 mm thick BWR plywood top alongwith 06 in Nos Countersunk screws and washers on three stiffeners all as shown on Drg and as specified and directed Make : Greenply Industries Ltd (Ply & Board Division) / Kitply / Century / Archidply

Removing the existing unsv shoes and Supply and fix new PVC shoes in legs of Bed Hard as per existing pattern.

REPAIRS TO CHAIR VERANDAH [ FD-359 & 256 ]

Removing the existing unserviceable/ plastic cane, scrapping the old paint and apply two coats of synthetic enamel paint white colour as specified and directed

Re-canning of chairs verandah with 4 mm wide 0.5mm thick plastic cane complete all as specified and shown on drg.Preparing the existing steel surfaces and panting with two coats of white synthetic enamel paint as specified and directed

S & F new PVC shoes for chair verandah inclidung taking down old shoes complete all as specified and shown on Drg.

REPAIRS TO CHARPOY GI PIPE PLYWOOD TOP: [FD-220 ]

Removing the existing unserviceable ply wood from GI charpoy and supply & fix 12mm thick plywood, BWR grade, ISI marked alongwith two angle iron stiffeners 900x25x3mm with 08 Nos Nut Bolt complete all as specified and directed. Make : Greenply Industries Ltd (Ply & Board Division) / Kitply / Century / Archidply

Removing the existing unserviceable / broken long rail 32mm dia and supplying and fixing new long rail for charpoy GI Pipe of Make : TATA/JINDAL/ASIAN .

Preparing short rail from broken long rail obtained from Sl item No 4.02 above and fixing for charpoy GI pipe complete all as specified and shown on drawing including removing the existing broken/ unserviceable short rail .

Preparing leg of GI Charpoy made from old short rail obtained from item No 4.03 above and welding 3mm thick base plate to the bottom of the leg and preparing MNF clamp holes as per existing and all as specified

Supply and fixing GI 3 way elbow 32mm bore,ISI marked, length not less than 65mm in each way including dismantling of old GI elbow.

Supply and fixing GI checknut, 5mm thick suitable for 32mm GI pipe pe including dismantling of unserviceable checknut.

CHAIR CB STEEL WITH ARMS [DRG NO: (FD-75M) ]

Removing the existing unserviceable/ broken seat for chair CB steel with arms and supply and fix new Seat of size 450 x 390 mm complete with frame made out of 50 X 50 mm 1st class hard wood members duly painted with black paint & canned with 2 mm wide plastic cane of oval shaped & 4 mm wide plastic cane for borders in Godrej pattern complete all as specified and shown on drg including fench polishing to wooden surfaces all as directed.

All as per item No 5.01 above but for back of chair CB steel with Arms

Removing the existing unserviceable/ broken Arms rest for chair CB steel with arms and supply and fix new Arms rest of size 420 X 50 X 20mm 1st class hard wood duly painted in black colour paint made to complete all as specified & shown on drg including french polishing to exposed surfaces all as directed. (Each Arms rest measured separately)

Supply and fix MS plate of size 50mm X 20mm X 4 mm thick duly welded and painted on two seat pipe to support seat of chair CB steel all as specified and directed.

Preparation of steel surfaces of chair CB steel with arms and applying two coat of synthetic enamel paint of approved colour complete all as directed

CHARPOY HARD TOP [DRG NO: (FD/MAP-II/01 ) ]

Removing the old welding spots from broken welding joints and re-welding in the same place as required & denting and straightning of MS Pipes. Thereafter preparation of old surface by sand paper No 50 and wire brush and apply two coat of synthetic enamel paint of black colour on complete item all as specified and directed.

Removing the existing unserviceable /broken ply wood top and supply and fixing new 12 mm thick BWR plywood top alongwith countersunk screws bolted on the stiffners 06 in Nos all as shown on Drg and as specified and directed . Make : Greenply Industries Ltd (Ply & Board Division) / Kitply / Century / Archidply

REPAIRS TO CHAIR WRITING OFFICERS [DRG NO: (FD/E6/MAP/12) ]

Removing the existing unsv PVC arm rest and Supply and Fix in repairs new PVC armrest of best quality of size 24cmx 6.4cmx 3.3cm shall be made out of polyurethane 76-85 shore ‘A’ Hardness. Pair of two will measure as one unit.

Removing unsv Seat of chair writing and Supply and Fix new Seat 75mm thick polyurethane foam(PU) moulded with density 50-55kg per cubic mtr thick and hardness duly covered with tapesry cloth not less than 200/- per RM all as specified and directed.

All as per item No 7.02 above but back of chair writing

Removing unsv shoes of chair writing and Supply and fix new shoes of chair including painting of metal portion all as specified and directed

LOCKERS STEEL BED SIDE [DRG NO: ( FD-1029)]

Removing the existing unserviceable handle of locker bedside & Supply and fix new 100 mm long Handle all as specified & shown on drg.

Removing the existing unserviceable hasp & staples & Supply and fix new mild steel 100 mm long hasp & staples all as specified & shown on drg.

Preparation of old painted surfaces of locker steel internally and externally including shelves (Top & bottom) by No 50 sand paper and wire brush. Applying putty on the patch and rubbing with sand paper No 150 to make surface even. Thereafter applying one coat of red oxide primer and applying two coat synthetic enamel paint by spray painting of approved colour all as specified and shown on drawing.

Supply and fix new legs of locker steel made of 1.6 mm thick MS sheet bend to shape duly painted with one coat of Red oxide primer and fix with Gas welding as shown on drg including removing of unserviceable legs complete all as directed.

Removing unsv conduit pipe and supplying and fixing new chromium plated 20mm dia conduit pipe of 1.6mm thick wall thickness

Removing unsv hinges and Supplying and fixing new hinges to shutters by reveting or gas welding as per existing

TABLE DINING ORs STEEL [DRG NO: (FD-165M) ]

Preparation of surface by scrapping the old paint and painting of complete M.S frame with synthetic enamelled paint of black/OG colour over coat of red oxide primer

Removal of u/s Top of table and supply and fixing new top of size 1800x600x18mm made out of Block board/ plywood 18mm covered from all side with Aluminium sheet 22 gauge thick covered alround. Top fixed with steel screw of required size complete all as directed.

Removal of u/s PVC shoes and Supply and fix new PVC shoes suitable for MS pipe 25mm square complete all as directed.

TABLE OFFICE OFFICER/ CLERK/ TYPIST STEEL [DRG NO: (FD-84/1004/1003/1006) ]

Removing the existing unserviceable/ broken top of steel table office offrs and Supply and fix new table top of 1370 X 760 mm of 18 mm thick prelaminated Particle Board board exterior grade with both side decorative with 6mm thick half round teakwood edging around all as specified on drg.

Removing the existing unserviceable/ damaged drawers of table office offrs steel/ table clk steel and Supply and fix new drawers made of 1 mm thick MS sheet bend to shape as including necessary welding shown on drg.

Removing the existing unsv lock and supply and fix new brass lock of harrison/Link/Godrej 65mm 6 lever with duplicate keys

Preparation of old painted surfaces of tables internally and externally including shelves (Top & bottom) by No 50 sand paper and wire brush. Applying putty on the patch and rubbing with sand paper No 150 to make surface even Thereafter applying one coat of red oxide primer and applying two coat synthetic enamel paint by spray painting of approved colour all as specified and shown on drawing.

TABLE (900x600) STEEL WITHOUT/WITH DRAWER [DRG NO: (FD-1007/1008) ]

Removing the existing unserviceable/ broken top of steel table office offrs and Supply and fix new table top of 900 X 600 mm of 18 mm thick prelaminated particle board exterior grade both side decorative with standard PVC edging around and all as shown on drg.

Removing the existing unserviceable/ damaged drawers of table 900x600 and Supply and fix new drawers made of 1 mm thick MS sheet bend to shape as including necessary welding shown on drg.

Removing the existing unsv lock and supply and fix new lock with duplicate keys

Preparing steel surface of table by scrapping old paint and applying two coat of synthetic enamel paint by spray painting complete all as specified & shown on drg.

Table Bed side [DRG NO: (FD/E6/MAP/15R) ]

Removing the existing unserviceable top & supply & fix 18 mm thick pre-laminated particle Board exterior grade of size 450mmx450mm with 6 mm thick teakwood edging all round & treated with French polishing including welding to repairable frames complete all as shown on drgs.

Preparing old painted steel surfaces of frame & apply one coat of black synthetic enamel paint including removing the unsv rubber shoes and supply and fixing new of same size rubber shoes all as specified and directed.

Removing unsv Telescopic channel and supply and fix new telescopic channel 300mm long in any large or small drawers of table bed side all as specified and directed.

Chair school with Hand Board [DRG NO: (FD/E6/MAP/15R)]

Removing the existing unserviceable openable top & supply & fix 18 mm thick pre-laminated particle Board exterior grade with PVC edging(hinged on RHS) screwed to 25 mm thick hollow pipe inserted in 20 mm thick MS rod welded to frame including welding complete all as shown on drgs.

Removing the old welding spots from broken welding joints and re-welding in the same place as required.Preparing old painted steel surfaces of frame & apply one coat of red oxide primer and painting the steel portion with black synthetic enamel paint all as specified and shown on drg.

Removing unsv one piece back & seat and supply and fixing of make Blowplast or equivalent all as specified and shown on drg.

REPAIR TO SIDE BOARD /BOOK CASE / BIN SOILED LINEN MULTI PURPOSE ((FD-26/241/FD-371) , (FD-287/FD-237),(DB-4122) , FD/E6/MAP/09)

Removing the existing unsv/ broken shutter of side board, book case & bin soled linen and supply and fix new shutter made of 18 mm thick prelaminated particle Board Exterior Grade with 40 mm wide piano hinges including handle100 mm long or knob and magnetic catcher alongwith teakwood beading 6mm thick all around, complete all as specified and shown in drg. (Each leaf to be measured separately).

Removing the unserviceable broken back ply of side board,book case & bin soled linen and supply and fixing new 6 mm thick BWR grade plywood all as specified and shown on drg.

Removing the unserviceable/ broken drawers of side board & bin soled linen and supply and fixing new drawers made of front 18 mm thick prelaminated Particle Board Exterior Grade and bottom of drawer with 6 mm thick BWR grade plywood duly fixing of 40 mm knob or handle as per existing specified and shown on drg.

Material and labour for Preparation of surface and French polishing to side board inner and outer except prelaminated portion as directed.

REPAIR TO TABLE DINING 6PERS(FD-80 (M)/273),(FD/MAP-II/03)

Removing the existing unsv/ broken top of Table dining 6 pers and supply and fix new top of prelaminated prelaminated Particle Board exterior grade of 18 mm thick both side laminated duly covered with teakwood beading 6mm thick half round all around, complete all as specified and directed.

Removing the existing unsv/ broken top long rails of Table dining 6 pers and supply and fix new long rails made of 1st class hard wood of size as shown on drawing complete all as specified and directed.

Removing the existing unsv/broken top short rails of Table dining 6 pers and supply and fix new short rails made of 1st class hard wood of size as shown on drawing all as specified and directed.

Removing the existing unsv/ broken legs of Table dining 6 pers and supply and fix new legs made of 1st class hard wood all as specified and shown on drg.

Material and labour for Preparation of surface and applying French polishing to Table dining 6 pers except laminated portion all as directed.

REPAIR TO TABLE DRESSING LADIES (FD-32/251 & 378/FD/MAP-II/07)

Removing the existing unsv/ broken drawers of Table dressing ladies and supply and fix new drawers front made of 18 mm thick prelaminatd Particle board and bottom of drawer with 6 mm thick BWR grade plywood duly fixed with aluminium anodised knobs 40 mm all as specified and shown on drg.

Removing the existing unserviceable/ broken mirror with 6mm thick back plywood of Table dressing ladies and supply and fix new mirror of 5 mm thick suitable to the existing frame alongwith 6mm thick BWR grade plywood back all as specified and shown on drg.

Meterial and Labour for Preparation of old surface and French polishing to Table dressing ladies except laminated portion all as directed.

REPAIR TO TABLE DINING 1200 x 900MM (FD-273), FD/MAP-II/03

Removing the unserviceable /damaged top of table dining and supply and fixing new top made up of 18 mm thick pre-laminated particle Board exterior grade both side laminated duly covered with teakwood beading 6mm thick half round all around, complete all as specified and directed.

Removing the unserviceable /broken legs of table dining and Supply and fix new leg made of 1st class hard wood all as specified and as shown on drg. (Note:each leg will be measured separately)

Removing the existing unsv/ broken top long rails of Table dining 4 pers and supply and fix new long rails made of 1st class hard wood of size as shown on drawing complete all as specified and directed.

All as per item No 17.03 here-in-before but top short rails of table dining 4 pers (Note:Each rail will be measured separately).

Material and labour for tightening and Preparation of old surface for french polishing to table dining complete all as directed.

REPAIR TO TABLE 900x600x760 MM W/O DRAWER (FD 42/284,(FD -55/223)

Removal of unserviceable leg and Supply and fix new leg made of 1st class hard wood for table Size complete all as specified & shown on drg.

Removal of u/s long stiffner under the top and Supply and fix new long stifner made out of 1st class hard wood for table Size all as per drg and complete all as per speciation and directed.

Removal of u/s top and Supply and fix new top made out of 18 mm thick prelaminated particle board of size 900x600mm Exterior Grade with teakwood beading 6mm thick half round all around, complete all as specified and directed.

Material and Labour for tightening and french polishing of complete table exposed to view except laminated portion complete all as per specified and directed.

REPAIR TO TABLE BED SIDE , (FD-276, 248)

Removal u/s plywood at back of table bed side and Supply and fix plywood 6mm thick BWR Gde as per drg and compelte all as specified and directed.

Material and Labour for french polishing of complete table exposed to view except laminated portion per drg and complete all as specified and directed.

Removal of unserviceable Top and Supply and fix new top of size 230mm X 450mm made out of 18mm thick prelaminated Particle board (exterior gde) beading around the top as per drg and complete all as per specified and directed.

REPAIR TO TABLE WRITING (FD- 33 & 275)

Removal of unserviceable leg and Supply and fix new leg made out of 1st class hard wood leg made out of 35mm x 55mm x 720mm in finished state as per drg and complete all as specified and directed.

Removal of unserviceable knob/handle of drawer and front shutter of cabinet and Supply and fix new knob heavy duty of quality as per sample available as per drg and complete all as specified and directed.

Removal of unserviceable side of cabinet of table and Supply and fix new side of cabinet made out of prelaminatd Particle board 18mm thick ext gde as per drg and complete all as specified and directed.

Taking out U/S shutter of cabinet and Supply and fix new shutter made out of prelaminated Particle board (Ext Gde) 18mm thick duly covered with 6mm thick teakwood beading with mild steel chromium plated piano continuous hinges through out with MS screw of appropriate size as per drg and complete all as specified and directed.

Removal of unserviceable top and Supply and fix new top of size 1145mm x 600mm made out of prelaminated Particle Board exterior grade of 18mm thick both side laminated duly covered with teakwood beading 6mm thick half round all around, complete all as specified.

Material and Labour for tightening & french polishing of complete table exposed to view except laminated portion all as specified and directed.

REPAIR TO CHAIR DINNING (FD-16(M), & FD- 279)

Removing the existing unserviceable/Broken rear leg and supplying and fixing 1st class hard wood rear leg complete alla s specified and shown on drgs (Note:Each leg measured separately)

Removing the existing unserviceable/ broken front leg and supplying and fixing 1st class hard wood front leg complete all as specified and shown on drgs (Note: Each leg measured spearately).

Removing the existing unserviceable/ broken fillet of canning and supplying and fixing 1st class hard wood fillet for canning including drilling holes complete all as specified and shown on drgs.

Removal of unserviceable back rest batten and Supply and fix new back rest batten made out of 1st class hard wood of size as per drg complete all as specified and directed.

Material and Labour for tightening & french polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs).

REPAIR TO CHAIR WRITING (FD-20 & FD- 280)

Removing the existing unserviceable/ broken rear leg and supplying and fixing 1st class hard wood rear leg complete all as specified and shown on drgs ( Note: Each leg measured separately)

Removing the existing unserviceable/ broken front leg and supplying and fixing 1st class hard wood front leg complete all as specified and shown on drgs ( Note: Each leg measured separately)

Removing the existing unserviceable/broken arms rest and supplying and fixing 1st class hard wood arms rest complete all as specified and shown on drgs (Note: Each arms rest measured separately)

Material and Labour for tightening & french polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs.

REPAIR TO CHAIR WOODEN BOTTOM (FD-56,FD-225 & FD-285)

Removing the existing unsv/ broken seat ply and supplying and fixing new seat made out of 6 mm ply wood commercial veneered face of both sides including drilling holes complete all as specified and shown on drgs. Note: Complete seat of one chair measured separately

Material and Labour for tightening and french polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs.

REPAIR TO CHAIR DINNING WITH PVC SEAT FD/MAP-II/05)

Removing the existing unserviceable/Broken rear leg and supplying and fixing 1st class hard wood rear leg complete alla s specified and shown on drgs. Note:Each leg measured separately)

Removing the existing unserviceable/ broken front leg and sjupplying and fixing 1st class hard wood front leg complete all as specified and shown on drgs. Note:Each leg measured spearately).

Removing the existing unserviceable/ broken PVC Seat of Chair Dining and Supply and fix new PVC Seat of Make Swastic/Harmony complete all as specified and shown on drgs.

Removal of unserviceable back rest batten and Supply and fix new back rest batten made out of 1st class hard wood of size as per drg complete all as specified and directed.

Material and Labour for tightening and french polishing to wooden surfaces for repaired chairs (old and new surfaces) complete all as specified and shown on drgs).

COMMON ITEMS FOR CHAIRS (FD-17,20,250 & 280) (FD-16,228 &279) (FD-202, 229 )

Removing the existing unsv/ broken plastic cane suplying and canning with new plastic cane 2 mm wide and 4 mm for borders for canning of chair of all types including couch with detachable chair, bin soied linen, stool dressing complete as per Godrej pattern all as specified and shown on drgs.

Supply & fix stiffeners for chairs made out of 25 X 25 mm 1st class hard wood after removing the existing unserviceable stiffeners complete all as specified and as shown on drgs.

REPAIR TO CHAIR DINNING CUSHIONED (FD/MAP-11/04)

Removing the existing worn out seat cushion and Supply and fix new PU foam seat foam of size 450X450X75mm thick, density 40 Kg/cum with 12 mm thick plywood BWR grade phenol bonded covered with tapestry cloth for chair dining cushioned complete all as specified and shown on drawing. Note: Tapestry cloth shall be approved by GE)

Material and Labour for tightening & preparation of surfaces and french polishing to wooden portion of chairs and applying two or more coat French polish on new surfaces and one coat on old surfaces to match uniform shade complete all as specified and shown on drg.

REPAIR TO TABLE CENTRE/PEG TABLE/TEAPOY(FD-235 & 274),(FD-277, 384), (FD-382,278,DB-3975)

Removing the existing unserviceable top of table centre and Supply and fix new top made out of 18 mm thick pre laminated Particle board exterior grade duly edging with 6mm thick beading including tightening and apply one coat of French polish to mate it in uniform shade complete all as specified and shown on drawing.(FD-235 & 274)

All as per item Ser No 27.01 above but top of Peg Table.FD-277, 384

All as per item Ser No 27.01 above but top of Teapoy.FD-382,278,DB-3975)

REPAIRS TO STOOL DRESSING CUSHION (FD/E6/MAP/14)

Replacement of existing foam cushions of Stool dressing cushion seat including existing tapestry cloth of Stool dressing cushion seat, and supply & fix new PU Moulded Foam 40 density of size 400 x 330 x 80mm thick, duly stitched with approved tapestry cloth and closed with valcrow of suitable size complete all as directed and shown on drg .

REPAIR TO BED PLY WOOD TOP (FD-21/245/246)

Removing the existing unserviceable/ broken long rail and supplying and fixing new 1st class hard wood long rail for charpoy wooden including French polishing all as specified and shown on Drg. Note:Each long rail measured separately).

Removing the existing unserviceable/broken head board assy including legs and supply & fixing new head board for bed ply wood top including teak wood legs and French polishing complete all as specified and shown on drg

Removing the existing unserviceable /broken foot board assy including legs and supply & fixing new foot board for bed plywood top including teak wood legs and French polishing complete all as specified and shown on Drgs.

Removing the existing unserviceable /broken ply wood top and supply and fixing new 12 mm thick BWR plywood Ext grade complete all as shown on Drg and as specified.

M/S KHAN ELECTRICAL (BID ID -3080720)

M.P.SUPPLY (BID ID -3080171)