SPL REPAIR TO JCOs MD ACCN BLDG NO P-10 AND P-14 (04 QTRs Each) AT DUNDAHERA MIL STN , GURUGRAM UNDER AGE B/R-II AND AGE E/M OF GE (SOUTH) DELHI CANTT-10

M & L for injecting chemical chlorpyrifos emulsifiable concentrate for Post Constructional Anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litre/RM including drilling and plugging holes etc. in apron complete all as specified and as directed.

M & L for Post Constructional Anti termite Treatment of soil under existing floors using chemical chlorpyrifos emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed.

M & L for mild steel TMT bars 10 mm dia & over as in reinforcement of columns, beams, RCC, slabs, chajjas, lintels etc cut to length bent to shape required including cranking, bending, spirally hoping for columns, hooking ends and welding the new reinforcement with old steel bars and including binding with mild steel wire not less than 0.90mm dia complete all as specified and as directed.

M&L for Reinforced cement concrete (Nominal Mix) type B1 1:2:4 using 12.5mm graded stone aggregate as slabs supported on walls, beams and columns in floors, roofs, landings, balconies, sunshades, canopies, deck slabs and in shelves and the like complete including necessary form work including demolition of reinforced cement concrete any type or in any position complete all as specified and as directed.

M&L for glazed ceramic coloured tiles, 8 to 9 mm thick size (600x600mm / 600x1200mm ), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15mm thick screed bed in cement mortar 1:4, including dismantling of cement concrete/terrazzo/ceramic tiles flooring in floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

M&L for glazed ceramic coloured tiles, 8 to 9 mm thick (match to floor), as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 10 mm thick backing coat in cement mortar 1:3, including dismantling of cement concrete/terrazzo/ceramic tiles skirting complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in cement mortar 1:6, including dismantling of existing flooring tiles complete all as specified and as directed.

M&L for joint free glazed ceramic coloured tiles in vertical surface 300x600x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match,over and including 10 mm thick backing coat in cement mortar 1:4, including dismantling of existing wall tiles complete all as specified and as directed.

M & L for 25 mm thick PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in level course under floor tiling etc complete all as specified and as directed.

M&L for Granite work,(of any type) 16-18 mm thick (table rubbed and polished including moulding edges with smooth finishing) as in cooking platforms, over and including 20 mm thick screed bed in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including dismantling of existing granite / tiles complete all as specified and as directed.

M&L for udaipur green marble work 16 to 18mm thick (table rubbed and polished including moulding the edges) as in jambs, pillars & window cills including 15mm thick scread/backing in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed.

S&F heavy duty full body 10 to 12mm thick, non skid ceramic tiles of any colour, any pattern any desing as approved by GE, area of each tile exc 0.04 Sqm but n.exc 0.36 Sqm as in floors/landing/steps/riser/parking/ footpath etc and over & including 15mm thick screed bed or bedding/rendering layer in cement mortar 1:4, including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles including dismantling of existing tiles of any description complete all as specified and as directed

Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc of any description including removing debrish from site complete all as specified and as directed.

M&L for brick work with flyash bricks straight or curved on plan exc. 6 mtr mean radius built in cement mortor 1:6, complete all as specified and as directed.

M&L for old size brick work with sub class `B' bricks straight or curved on plan exc. 6mtr mean radius built in cement mortor 1:6 except bricks, complete all as specified and as directed.

M&L old size Brick work with sub class 'B' bricks strainght or curved on plan to any radius in half thick in cement mortar 1:4 brick wall built in cement mortor, complete all as specified and as directed.

Supply and fixing of 20 mm outer dia CPVC pipes SDR 11 & CPVC SCH-40 fitting on walls / ceiling or laying in floors/wall including all fitting such as (brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor including taking down of existing GI tubing 15mm dia and connection complete all specified and as directed.

Supply and fixing of 25 mm outer dia CPVC pipes SDR 11 & CPVC SCH-40 fitting on walls / ceiling or laying in floors/wall including all fitting such as (brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor including taking down of existing GI tubing 20mm dia and connection complete all specified and as directed.

Supplying and fixing of 40 mm outer dia CPVC pipes SDR 11 & CPVC SCH-40 fitting on walls / ceiling or laying in floors/wall including all fitting such as (brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded adaptor etc) union ,ball valves, flange and tank adaptor including taking down of existing GI tubing 32-40mm dia and connection complete all specified and as directed.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank of capacity exceeding 250 litres but not exceeding 500 litres, complete all as specified and as directed.

S&F Ball brass valves, high pressure, with of PTMT with epoxy coated aluminium rod & high desity plastic ball ascrewed for iron pipe of 25mm bore and fixed, complete all as specified and as directed.

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and as directed.

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore, complete all as specified and as directed.

S&F PVC connections 600 mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and as directed.

S&F 15 mm Angle valve/Stop valves, cast copper alloy , chromium plated, fancy type screwed down high pressure with crutch and butter fly handles, screwed with pipes or for union, complete all as specified and as directed.

S&F two way CP brass Bib Cock 15mm dia with single handle and wall flange complete all as specified and as directed.

S&F 15 mm dia WHB mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified and as directed.

S & F 15 mm dia Wall mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified and as directed.

S & F 15 mm dia Sink mixer chromium plated screwed down highpressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified and as directed.

S&F in repairs brass chromium plated overhead shower rose 125mm dia, with revolving joint and shower rod to fixed to 15mm bore pipe, complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, 'D' type 60 cm long between flanges of brass CP, complete all as specified and as directed.

S&F in repair stainless steel sinks without drainage board made of stainless steel 1 mm thick sheet, for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F Health Faucet (ABS Body) chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed.

S & F Toilet paper holder of stainless steel, fixed to walls with chromium plated (CP) brass screws etc complete all as specified and as directed.

S&F corner glass assmbley with stainless steel railing, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan with P or S trap (pedestal pattern) , white, including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device, complete all as specified and as directed.

S&F in repair, PVC valveless, syphonic action type flushing cisterns 10 ltr capacity, low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level, complete all as specified and as directed.

S&F in repair vitreous china wash basin, white, flat back, size 450 x 300mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified and as directed.

Taking down (Steel Window)/doors chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

Taking down (Door) chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

S&F factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65 x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/ wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter fixing with including stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

S&F 30 mm thick factory made wire mesh solid WPC, consisting of Density 650 Kg /Cum Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mmx25mmx2mm and 32mm long steel screws drilled suitable to pass through Other hardwares should be fixed with 19x6mm size steel screws etc. complete all as specified and as directed.

S&F factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Spply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter fixed with and including stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

S&F for mild steel 300mm long, ordinary rat tail rod pattern springs including roller and roller plate complete, fixed with screws to wooden frame or welding to steel frames etc complete all as specified and as directed.

Dismantling wrought iron or mild steel / cast iron work of any description (steel window & Grill) complete all as specified and directed.

Supply, fabricating and fixing of powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be mooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete all as specified and as directed.

S&F 4.8mm thick sheet glass ordinary quality n.exc 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165, including dimantling old existing steel any type or in any position complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coat of synthetic enamel paint, complete all as specified and as directed.

S&F in repairs Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free/Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws including dismantlfing of existing of baord any type. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen and Cabinets. Note :- All necessary fittings and fixtures like nickle plated clip hinges, knobs etc complete all as specified and directed. (a) Pattern & design of WPC board to be decided by GE. (b) Items like, magnetic Catcher, cupboard 100mm SS handle, and CP Clip/continuous (piano) hinges,mild steel, bright finish or electrogalvanised, width of flap (when open) is 30mm, Haps & Staple deemed to be included in the quoted rate.

S&F in repair 25 mm dia with wall thickness of 1.6mm SS AISI 304 curtain rod, with fixing brackets, side knobs of good quality as approved complete all as specified and as directed.

M&L for welding in repairs exc 2.5 cm but not exc. 5.0 cm in length thickness of metal be welded exc 6mm but n.exc 9mm, complete all as specified and as directed.

S&F MS chromium plated peg set of five fixing with wall, complete all as specified and as directed.

S&F in repair kitchen plate rack with four shelves made out of stainless steel sheet 1 mm thick overall size not exceeding 450mm x 600mm x 250mm (Potrait shape) complete all as specified and as directed.

S&F in repair stainless steel AISI 304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and as directed.

S&F in repair stainless steel AISI 304 grade handle of size 200 mm long, etc., complete all as specified and as directed.

S&F in repair Stainless steel of AISI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts, complete all as specified and as directed.

M&L for 15 mm thick rendering with readymix plaster (as per manufaturer's instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement including taking down of existing plaster complete all as specified and as directed. Note :- Contractor shall be bounded to carryout repair / maint upto G+2 storey building and the rate shall be deemed including scafolding / double scafolding, safety equipments and misc accessories.

M&L for preparation of newly plastered surfaces of walls and applying 1mm thick waterproof cement based putty @ 1Kg (undiluted) per Sqm of Asian Paints or its equivalent over the new/old plastered wall after scrapping to prepare the surface even and smooth duly sanding, then applying one coat of acrylic waterbased exterior grade primer @ 0.8 ltr (undiluted)/10Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalent having an electric motor of min 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent coats at last providing and applying two coats of smooth acrylic emulsion with rich matt finish having voc less than 50 gram per ltr complying leed criteria @ 1 ltr (undiluted)/10Sqm diluted with water in 2:1 ratio applied over priming coat with fully automatic airless spray machine of paint application of Asian Paints Trucare Graco or equivalant having an electric motor of min 1 HP with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface in both the coats of paint, complete all as specified and as directed. Note :- 1. (Applicable to item above) At the time of execution of work contractor shall submit the MOU towards triparty agreement between contractor, Manufacturer of Paints from Asian Paints/Berger Paints/Goodlass Nerolac Paints or other manufacturer as specified in the list of make and their Applicators, for material and execution of work from any of the said manufacturers. 2. Terms of the MOU so entered between tenderes, Applicators and Manufacturers mentioned above shall also cover the gaurantee from manufacturer of paints for any defect in work executed by their applicator for a period of 3 Years. All other aspects with regard to payment, execution of work or other legal points shall be solely as decided between the Contractors, Paint manufacturer & Applicator. Department shall in no way be responsible for any complicacy arising at a later stage between the parties to MOU with regard to payments or execution of work. 4. The necessary steel scaffolding upto G+2 storeyed wherever required to execute the work shall be provided by the contractor with all safety equipments and the cost of providing scaffolding & safety equipments shall be deemed to be included in the quoted rates of the contractor and nothing extra shall be admissible on this account. 5. The work shall be executed in AOR of AGE B/R-I and is being restricted area and head loss etc shall be considered before quoting the rates by the contractor as nothing extra shall be admissible on this account.

M&L for 10 mm thick rendering with readymix plaster (as per manufaturer's instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement on wall including necessary scaffolding, formwork, safety precautions for multi storey bldgs up to G+2 stories including taking down of existing plaster complete all as specified and as directed.

M&L for two coats of oil bound distemper on walls/ceiling including preparation on new surfaces including a coat of primer and applying 1mm thick layer of wall putty on walls to give uniform surface including sanding of the putty surface with Asian Paints TruCare wall sander: L-01/H-01 or equivalent (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above having dia of 7”/9” to make the surface free from dust etc. by skilled labour, complete all as specified and as directed.

M&L for 5 mm thick rendering on ceiling surfaces with redimix plaster (as per manufaturer's instruction) on face of brick or concrete surfaces finished even and smooth surface without using extra cement on wall of up to Gthree stories bldgs. Make of ready mix plaster including taking down of existing plaster complete all as specified and as directed.

M & L for cutting of vegetation/scrubs plant (girth not exceeding 300mm) from roof, terrace, chajjas etc digging out the roots and making good the surface in PCC 1:2:4 type B1 with surfaces finished to match complete including scaffolding etc, complete all as specified and as directed.

Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area complete all as specified and as directed.

M&L for Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in roof pedding , finished even and smooth without using extra cement ,including cleaning the concrete surface by steel wire brushes, up to three stories bldgs, complete all as specified and as directed.

M&L for screed bed 10 mm thick plaster on concrete surfaces in cement mortar (1:3) on roof, mixed with water proofing compound and finishing the surface even and smooth without using extra cement all as specified and directed. Note : Rate quoted by the tenderer deemed to including the rate of water proofing compound.

M&L for roof treatment in following stages, complete all as specified and as directed :- (i) Preparation of concrete surfaces by wire brush and cleaned top surfaces of cement concrete . (ii) APP polymeric water proofing membrane minimum 3 mm thick and wieghing not less than 3.5 Kg per Sqm, black finish reinforced with non woven polyester matt with a thermo fasable finish laid over bitumen primer @ 0.5Kg/Sqm by torching application with a propane or a butrane gas torch with an overlap of 100 mm at the sides and 150mm at the ends, as per manufacturers instructiions incl preparation of surface. (Manufacturer as approved by GE).

S&F for Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on and including 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete all as specified and as directed.

S&F cast iron soil, waste and vent pipes (sand cast) 100 mm bore in any length with or without ears with cement joints fixed to walls/laid in trenches or in floor duly apply a coat of bitumenous black paint including dismantling cast iron pipe & reinforced concrete drain pipes, jointed in cement mortar of any dia complete all as specified and as directed.

All as per srl item No 76.00 here-in-before but 75 mm bore pipes fixed to wall/laid in trenches or in floor.

S&F Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door/Tee, union etc complete all as specified and as directed.

All as per srl item No 78.00 here-in-before but 75 mm bore.

S&F Stack clamps made out of 50X5 mm flat iron and 6 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100/110mm bore pipe complete all as specifiecd and as directed.

S&F Stack clamps made out of 50X5mm flat iron and 6mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore complete all as specifiecd and as directed.

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 75 mm bore complete all as specifiecd and as directed.

S&F Cast iron branch pieces single (equal unequal ordinary or inverted (Spigot or socketed type) or with parelled branches 100mm bore complete all as specifiecd and as directed.

S&F cast iron vent cowl for 100mm bore pipe complete all as specifiecd and as directed.

S&F cast iron floor trap/nahani trap 75 mm, with grating including jointing to waste pipe complete all as specifiecd and as directed.

S&F 125mm x 100mm salt glazed stone ware gully traps square & round mouthered trap 'P' including case iron grating and fixed, including necessary excavation and earthwork, concrete in bed, surrounds, kerbs etc., and jointing to drains in cement mortar 1:1, complete all as specified and as directed.

PVC (SWR) pipes 110mm bore single socketed , in any length with rubber ring joints fixed to wall including dismantling of existing SWR/PVC/Salt glazed ware/AC or reinforced concrete pipe set in cement mortar etc. complete all as specified and as directed.

S&F PVC (SWR) bend any radius for 110mm bore pipe complete all as specifiecd and as directed.

M&L for cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection, 50 mm thick, finished even and smooth without using extra cement, including machine pressed, factory made, Glossy finished chequered cement concrete tiles 20cmx20cmx(22-25) mm thick, set jointed and pointed in neat cement slurry in floor with grey cement and pigment over and including 20 mm thick screed bed are bedding layer of cement mortar (1:4) for laying floor finishes complete all as per specified and as directed.

S&F 18 mm thick WPC grill jalli over Arch section stair case area / compound wall superior quality fixing with stainless steel holow square pipes over frame work (Grade 304) including SS nails / screws or as per requirement at site design as approved by GE inluding dismantling existing RCC / Concrete arch sec complete all specified and as directed. Note :- Cost of SS nails / screws and all fittings/ fixtures deemed to be included in the above quoted rates and no extra shall be paid.

M & L for stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specifiecd and as directed.

M & L for false ceiling at all hights with GRG (Glass Fifre Reinforced Gypsum, with fully perforated 12 mm thick micro tegular edged or 10mm thick square edged GRG false ceiling) False Ceiling Tiles of size 595x595mm of approved texture, design and patterns having Moisture contant less then 2% Humidity resistance of 99%, NRC .050-0.85 as per IS8225:1987,Non combustible as per BS 476(Part -4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal lavel suspended on inter- locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @120grams per sqm including both sides ) comprising of main - T runners of size 15x32mm of length 3000 mm ,Cross - T of size 15x32 mm of length 1200 mm and secondary intermediate Cross T of size 15x32mm of length 600mm of form Grid module of size 600x600mm, suspended from ceiling using galavanised mild steel items (galvanizing @80 grams per sqm) i.e.50mm long, 8mm outer diameter M- 6 dash Fasteners,6mm dia fully threaded hanger rod upto 1000mm length and L -Shape lavel adjuster of size 85x25x2mm Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rrawl plugs at 450mm center to center and 40mm long dry wall SS screws including dismantling of existing false ceiling board any type complete all as specifiecd and as directed.

S&F stainless steel wire cloth, 0.63mm nominal dia or wire and sqm average width or aperature 1.40mm, fixed with tinned tacks or galvanised wire staples to doors/steel windows, complete all as specifiecd and as directed.

M&L for Granite (of any type) work, 16-18 mm thk (table rubbed and polished including moulding edges with smooth finishing and creating 50mm wide patti with sand blasting over steps for non-skid surface) in steps/riser/skirting etc including 20mm thick screed bed cement mortar 1:4 in floor and 15mm thick screed bed in cement mortar 1:4 in vertical surfaces including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including dismantling of existing granite / tiles complete all as specifiecd and as directed.

S&F 4 mm thick figured glass/pin head/frosted glass n.exc 0.50 sqm each pane and fixed with oil putty or with wooden beading in square etc complete all as specifiecd and as directed.

M&L for cement plaster 15mm thick in cement mortar 1:6 on brick or conc surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete all as specifiecd and as directed. NOTE : Rates for water proofing compound/ polymer deemed to be included in the above rates.

M &L for providing and applying a bond coat of Latex:Water:cement - 1:4:6 consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing complete all as specifiecd and as directed.

M&L for Exposing the first joint of masonry structure at ground level horizontally and knocking off the plaster least 50 cm beyond the visibly penetrated area., scrapping out damaged mortar joints to a depth of approximately 2-3 cm. Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer's instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes by air blower prior to fixing nozzles, installation of latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten, Fixing the packer securely using sealent and Cutting/removing of Packers after completion of grouting/injecting without damaging structural elements complete all as specified and as directed.

Supplying and application of very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time, having mixed viscosity 3 to 11 m.Pa.s at 20 Deg C, reaction time adjustable according to ambient temperature and execution time requirement between 8-50 mins, the polyacrylic resin is pumped into the wall through packers injection at a pressure > 20 Bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas cause rising dampness. When polyacrylic resin movement stops or polymer compound appears at the packer, move to the next packers and inject (Approx 0.2-0.3 Kg resin per packer) complete all as specified and as directed. Make : SIKA/FOSROC/BASF

M&L for 75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Supply and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for plain cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in height, coping, kneeless apex stones , kerb stone, bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 (12.5mm graded aggregate) complete all as specified and as directed.

M&L for two coats of synthetic enamel paint on new/old concrete or plastered surfaces (as in kerb stones etc) over a coat of primer including preparation of new surface complete all as specified and as directed.

Taking down old and unserviceable submain wiring any size of two core including earth wire complete including batten/ conduit and make good the disturbed surface to match the existing surface complete all as specified and as directed.

Taking down old and unserviceable copper/alumunium point wiring in batten/ conduit and make good the disturbed surface to match the existing surface, complete all as specified and as directed.

Taking down old and unserviceable, distribution board any type including/ sheet metal enclosures, after removing all connection and make good the disturbed surface complete all as specified and as directed.

M&L for Point wiring using FRLS-H PVC insulated unsheathed, multistranded copper conductor cable 1.5 sqmm drawn through and including PVC conduit of min 20 mm dia by Cutting chases for conduits and sinking's for boxes and making good to walls, floors etc for concealed conduit wiring with modular flush box metal of GI sheet minimum 1.8 mm thick with earth terminal for safety, flush metal GI box of required modules as per site requirement and modular plate with support frame white in colour of required modules, 3mm thick including all fittings i.e. tees, bands and junction boxes, screws etc. complete for One light/Fan point controlled by one switch 6 Amps one way using cable (1.5 Sq mm for phase and neutral and 1.5 sq mm earthing) Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate complete for one light/fan point controlled by one way switch complete all as specified and as directed.

All as per srl item No 107.00 here-in-before but One 3 pin socket outlet, 5 Amp socket outlet on same board controlled with other switches.

All as per srl item No 107.00 here-in-before but One 5 pin socket outlet, 5 Amp socket outlet on independent board.

All as per srl item No 107.00 here-in-before but one light point controlled by two way switches,

All as per srl item No 107.00 here-in-before but One bell / buzzer point controlled by one bell push on independent board complete all as specified and directed.

All as per srl item No 107.00 here-in-before but one 3 pin 15 Amps socket outlet independent with multistranded copper conductor cable 2.5 sqmm.

S&F Modular Bell push 10A 1 Module with inidicator IP-20 white colour complete all as specified and as directed.

S&F buzzer dingdong AC 230 Volts, single pole, 50 Hz complete all as specified and as directed.

S&F Modular Shuttered Socket, 6A - 2/3 pin 2 module IP-20 white colour on same board complete all as specified and as directed.

S&F Modular Shuttered Socket & switch combination, 6A - 2/3 pin 2 module IP-20 white colour on independent board complete all as specified and as directed.

S&F Modular shuttered Socket 6/16A - 2/3 pin combined IP-20 white colour complete all as specified and as directed.

S&F switch modular type 1way 16A, 1module with indicator IP-20 white colour complete all as specified and as directed.

S&F in replacement Wall mounted LED Integrated Batten 20 Watt - 4Ft White,CRI 80, aluminium housing, 120 Lumens per watt,6500K(cool White)4000 K (Natural White), Pf < 0.90 indoor LED battern IP-40 complete all as specified and as directed.

S&F in replacement Wall mounted LED Integrated Batten 10 Watt - 2Ft White,CRI 80, aluminium housing, 120 Lumens per watt,6500K(cool White)4000 K (Natural White), Pf < 0.90 indoor LED battern complete all as specified and as directed.

S & F LED lamp 9W LED lamp suitable for B-22 holder complete all as specified and as directed.

S&F switch modular type, 1 way 10A, 1module IP-20 white colour complete all as specified and as directed.

S & F Switch Modular type switch, 10 A 2- way 1 Module IP-20 white colour complete all as specified and as directed.

Taking down existing unserviceable ceiling and exhaust fans with all connected items and deposited EM store yard and making good the disturbed surface on ceiling/fan hook and refixing on same position complete all as specified and as directed.

S & F Modular fan regulator 120 W 2 module complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding motor and sweep 300 mm CMH 800-950 and connecting up with replacement of cable T/C flexible cable of size:- 1.50 Sqmm from ceiling rose / connection to fan and taking out fan and deposited to E/M store yard complete all as specified and as directed. Note: Making of hole/opening in wall or window including necessary making good the surface is included in the quoted rate by the tenderer.

Supply, Installation, testing and commissioning of 1200mm sweep BEE 5 star rated, Ceiling fan with remote control, Suitable cell for remote, Brush Less Direct Current (BLDC) Motor, Class of insulation : B, 3 Nos Blade, 30 cm long down road, 2 Nos canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery not less than 220 CMM, 350 RPM (tolerance as per IS:374-2019), THD less than 10%, and all remaining accessories including safety pin, nuts bolts, washers, temperature rise =75 degree C (maximum), insulation resistance more than 2 mega Ohm, suitable for 230V, 50 Hz, single phase AC supply complete all as specified and as directed. including taking down old ceiling fan and depositing to MES store yard.

Supply and fixing ceiling rose, 3 phase/PVC/polycarbonate, isolated body type complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast luminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing in repair Sheet Metal enclosure double door for DBs when MCBs to be used SPN- 12 Way with 200 Amp rated bus bar complete all as specified and as directed.

Supply and fixing of amp rating 240V, 10KA, 'C' curve miniature circuit breaker (MCB) SPN and current carrying capacity 40 Amps in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing repair amp rating 240V, 10KA, 'C'curve miniature circuit breaker (MCB) SP and current carrying capacity 5-32 Amps in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4.0 Sqmm to be drawn through and including PVC conduit 20mm dia medium Grade concealed in walls/roof/floors including taking down the old submain wiring complete all as specified and as directed. Notes:- Two wires of 4 sqmm and one wire of 4.0 sqmm and one run of PVC conduit shall be measured as one unit.

M&L for sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6.0 Sqmm to be drawn through and including PVC conduit 20mm dia medium Grade concealed in walls/roof/floors including taking down the old submain wiring complete all as specified and directed by Engineer in Charge.Notes:- (i) Two wires of 6 sqmm and one wire of 6.0 sqmm and one run of PVC conduit shall be measured as one unit.

Supply & fixing of water storage heater, 5 star rated with Marine grade glass line coating Tank Efficient long life copper heating element ,Adjustable Thermostat, Shock resistant amd rust proof engineering thermoplatic body, waterproof technology, Tank design is suitable to withstand 8 bar pressure (Geyser) of capacity 25 litre ISI mark, PRCD, Ac Supply, 240 volt, complete , 3 core lead, including safety valve, including electric and water connection and making good to disturbed surface complete all as specified and as directed. Note : Electric switch for geyser of 16 Amps shall be provided on main switch board of the bathroom and socket outlet shall be provided near the geyser and will be measured as 16 amps power wiring against item no.113

Supply and fixing of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 volts complete all as specified and as directed.

M & L for GI pipe bracket made out of galvanised iron tubing 40 mm bore (dia), light grade, 1.20 Mtr long bent to shape as per specified for fixing street light fitting including suitable size of clamps and applying two coats of alluminium paint over a coat of aluminium primer including taking down old unserviceable GI pipe bracket with clamps complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5m in depth and getting out for taking out/laying of GI pipe of any size complete all as specified and as directed.

Returning, filling icluding , spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Removing excavated materials to distance not excedding 50m and deposting where directed as level not exceeding 1.5m above the starting point complete all as specified and as directed.

Taking out/taking down old unserviceable damaged GI/PPR pipe size of 20/25/50 mm dia from excavated trenches including removing of fittings all as directed for necessary replacement /relaying serviceable GI pipe complete all as specified and as directed.

Supply and fixing of 50 mm bore GI water tubing, medium grade, with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor trench complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc), complete all as specified and as directed.

All as per srl item No 142.00 here-in-before but 25 mm bore.

All as per srl item No 142.00 here-in-before but 20 mm bore.

Supply and fixing in repair 25 mm bore Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed, complete, all as specified and as directed.

All as per srl item No 145.00 here-in-before but 50 mm bore.

S&F GI Flat strip clamps of size 25mm x 3mm duly bended as per the size of GI tubing and site condition,drilled complete, all as specified and as directed.

Supply and fixing of heavy rust proof passivated bolts made of steel of size 8 mm dia 75 mm long including necessary drilling on wall for fixing of steel frame complete, all as specified and as directed.

M & L for cutting the existing GI/PPR pipe and making connection of GI distribution branch with DI main of sizes 80/100 mm dia by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

Supply and laying dry river sand laid in trenches as cable cushioning and covering complete all as specified and as directed. Note : Punned thickness only measured and paid.

M & L for brick sub class 'B' lais over sand cushioning to cable in trenches keping width of brick paraller to the length of cable complete all as specified and directed.

Supply and laying jointing, testing and comissioning of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable 35 Sqmm 3.5 core with aluminium conductor laid in trenches/pipes, fixed to poles/walls with suitable saddle aluminium lugs, gland if required and jointed including taking down of old cable complete all as specified and as directed.

Supply and laying GI tube light grade size of 40 mm dia laid through trenches/under road floor for cable protection complete all as specified and directed.

M & L for Earthing complete with galvanized street earth plate electrode 600x600x6mm thick buried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanized iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (.c) CI cover with suitable handle (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminum lugs etc all as specified.(e) 15mm nominal bore medium grade GI protection pipe up to 7.50 meter long for protection of earthing lead.(f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.