REPAIR/ RENEWAL/ MAINTENANCE OF PUMP SETS, MOTOR STARTERS, LT PANELS, APFC PANELS DG SETS AND CONNECTED ITEMS AT MIL STATION SOLAN UNDER GE KASAULI

Amount

Schedule 'A' Section - I

Disconnecting the electrical connections of motor, water supply to the Pump and taking out pump after disconnecting both motor and pump mechanically 10 to 15 HP capacity, capacity - 45 Cum at 35 metres head installed at Water Pump House and Back Solan and transporting the same to an authorized workshop for following repairs :-

S&F Shaft with keys made out of steel 410 grade for Srl Item No 1.00

Shaft sleeve with nuts made out of stainless steel 410 grade for Srl Item No 1.00

Set of pins and Gaskets made out of Mild Steel for Srl Item No 1.00

Coupling set made out of Cast Iron including bolts, nuts, washers & rubber bushes for Srl Item No1.00

Gland box made out of Cast Iron including gland box studs with nuts and washers for Srl Item No1.00

Gland packing made out of Gr. Cotton for Srl Item No 1.00

Impeller made out of cast Iron duly balanced by means of precision lathe machine for Srl Item No 1.00

Driving End bearing for Srl Item No1.00

Non Driving End bearing for Srl Item No 1.00

Disconnecting the electrical and mechanical connections of motor, and taking out motor,15 HP capacity at Solan Pump House. Transporting the same to an authorized workshop for following repairs:-(a) Dismantling burnt AC 3 Phase, 50 Hz, motor, 15 HP taking out all coils and re-winding the motor complete with same gauge of wire and same nos of turns. Heating, Baking and varnishing the winding complete. Re-assembling the motor and fixing back in position all as directed by Engr-in-Charge and recommended by the manufacturer.

All as per item No 2.00 here-in-before but for, 10 HP capacity .

Supply & fixing in repairs Volt Meter Digital, 96 x 96 mm, 0-500 Volts, Class 1, AC.

Supply & fixing in repairs Amp Meter Digital, 96 x 96 mm, 0-100 Amps, Class 1, AC.

Supply & fixing in repairs die cast resin CT, Class 1, for digital Amp Meters. Ratio of CT- all as directed by Engineer- in-Charge.

Taking out old & unserviceable power contactor and Supply & fix power contactor for S/D starter 15 HP 3 pole, 32 Amps for AC 3 rating 415 volts, 15 kW 50 Hz supply including control coil, 1NO+1NC, contact springs, spring retainers and arc runners complete.

Taking out old & unserviceable power contactor and Supply & fix power contactor for S/D starter 10 HP ,3 pole,12 Amps for AC 3 rating 415 volts, 5.5 KW , 50 Hz supply including control coil, 1NO+1NC, contact springs, spring retainers and arc runners complete.

Supply / laid PVC insulated unsheathed multistranded HRFR 3 x single core ( R,Y,B) copper conductor 1100 volts grade of size 16 sqmm passing through existing PVC/ERW conduit from starter upto pump fixed with required size of copper lugs complete all as specified and directed by Engr-in-Charge.( Note- 3 single core wire of 16 sqmm ( colour coding RYB) will be measured as one length of 1 RM)

S&F in replacement of Water meter 100 mm nominal bore conforming to IS:2373-1981 having CI casing bronze body and SS/Alloy/Bronze gear having dial duly marked with litres or kilolitres in boldface, thread/flanged end type with provision of strainer out side the meter complete all as specified and as directed .

S&F in replacement of Foot Valve conforming to IS-4038 flanged ISI marked completed with nut, bolts, washers etc including taking out old existing u/s foot valve of 100 mm dia.

S&F Push Button 22.5 mm with push knob flush type having 1 NO & 1 NC illuminated type for putting on / off the starter.

S&F LED indicating light surge and low voltage protected 220 / 240 Volts AC, Colour R/Y/G/A for LT Panels.

S&F electronic star delta Timer ( 1 to100 sec) DQR 415/240V, 110V : AC complete.

Cutting down leaking piece of pipe 100mm. Cut down the rusted & leaking portion , providing (i) new piece of GI pipe 100 mm medium grade upto 0.50 metre long (ii) New union socket 100 mm - 1 Nos. (iii) Jointing the new pipe with existing old pipe by means of welding to make it leakproof including testing on completion complete all as specified and directed.'Note:- Unit rate quoted shall be included for (a) Necessary excavation/earth work (b) New GI pipe 100 mm upto 0.50 metre length (c ) union socket 100mm - 1 Nos. (d) welding etc complete including testing on completion.

Cutting down leaking piece of pipe 80mm. Cut down the rusted & leaking portion , providing (i) new piece of GI pipe 80 mm medium grade upto 0.50 metre long (ii) New union socket 80 mm - 1 Nos. (iii) Jointing the new pipe with existing old pipe by means of welding to make it leakproof including testing on completion complete all as specified and directed.'Note:- Unit rate quoted shall be included for (a) Necessary excavation/earth work (b) New GI pipe 80 mm upto 0.50 metre length (c ) union socket 80mm - 1 Nos. (d) welding etc complete including testing on completion.

Cutting down leaking piece of pipe 50mm. Cut down the rusted & leaking portion , providing (i) new piece of GI pipe 50 mm medium grade upto 0.50 metre long (ii) New union socket 50 mm - 1 Nos. (iii) Jointing the new pipe with existing old pipe by means of welding to make it leakproof including testing on completion complete all as specified and directed.'Note:- Unit rate quoted shall be included for (a) Necessary excavation/earth work (b) New GI pipe 50 mm upto 0.50 metre length (c ) union socket 50mm - 1 Nos. (d) welding etc complete including testing on completion.

Cutting down leaking piece of pipe 40mm. Cut down the rusted & leaking portion , providing (i) new piece of GI pipe 40 mm medium grade upto 0.50 metre long (ii) New union socket 40 mm - 1 Nos. (iii) Jointing the new pipe with existing old pipe by means of welding to make it leakproof including testing on completion complete all as specified and directed.'Note:- Unit rate quoted shall be included for (a) Necessary excavation/earth work (b) New GI pipe 40 mm upto 0.50 metre length (c ) union socket 50mm - 1 Nos. (d) welding etc complete including testing on completion.

Cutting down leaking piece of pipe 25mm. Cut down the rusted & leaking portion , providing (i) new piece of GI pipe 25 mm medium grade upto 0.50 metre long (ii) New union socket 25 mm - 1 Nos. (iii) Jointing the new pipe with existing old pipe by means of welding to make it leakproof including testing on completion complete all as specified and directed.'Note:- Unit rate quoted shall be included for (a) Necessary excavation/earth work (b) New GI pipe 25 mm upto 0.50 metre length (c ) union socket 50mm - 1 Nos. (d) welding etc complete including testing on completion.

Cutting down leaking piece of pipe 20mm. Cut down the rusted & leaking portion , providing (i) new piece of GI pipe 20 mm medium grade upto 0.50 metre long (ii) New union socket 20 mm - 1 Nos. (iii) Jointing the new pipe with existing old pipe by means of welding to make it leakproof including testing on completion complete all as specified and directed.'Note:- Unit rate quoted shall be included for (a) Necessary excavation/earth work (b) New GI pipe 20 mm upto 0.50 metre length (c ) union socket 20mm - 1 Nos. (d) welding etc complete including testing on completion.

Cleaning of RCC OH Tank of capacity 50000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump.

Cleaning of RCC UG sump of capacity 100000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump.

Cleaning of RCC UG sump of capacity 30000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump.

Cleaning of RCC Semi UG sump of capacity 15000 Gln on staging 20 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump.

Cleaning of RCC Semi UG sump of capacity 10000 Gln on staging 10 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump.

Cleaning of RCC Semi UG sump of capacity 5000 Gln on staging 10 feet height throughly removing mud, grits etc. from the sump by following method:- (a) Removing all dirt,mud with the help of containers mannually from inside to the water storage Sump, then scraping to walls/pillars/floor complete as directed. (b) Washing with clean water after scraping with wire brush in side and removing mud and spoil to a distance n.exc. 50 mtrs.(c) Washing with clean water and bleaching powder including scraping wire brush on walls/pillars/floor removing mud, grits & deposits etc properly. (d) Repair/ Replacement to all inlet/out lets of sump with a reqd size of MS/GI Pipe as directed including cement work etc complete leakage proof.(MS/GI Pipe if reqd, it will be measured and paid separately).(e) Dry washed walls, coating with a one coat of white cement in side and out side two coat of white wash with lime the whole surface of walls/pillars and floor/roof of sump.

Taking out existing earthings and M&L for replacement of chemical earthing (Pipe in pipe technology) Two B class IS mild steel pipe, one inside the other, hot dip galvanised with 100 micron coating outside and about 300 micron coating inside filled with high conductive and corrosion Resistant Crystalline Mixture inside and Backfill compound around the outer electrode) outer electrode dia 72 to 80mm and inner electrode dia 35 to 40 mm both 10' long, incldg making earth pit of size 4' x 4' and 11' deep fill the entire pit with black cotton soil or normal soil, pour enough water so that pit is full with water, leave it for three days so that soil soaks up the water, the soil level has goes down, again top up the pit with soil & fill the water. After two or three days when the pit is sturdy and ready for earthing purpose, install the earthing electrode as per installation method as below:- (a) Mix backfill compound evenly with soil. (b) Remove plastic sleeve carefully from electrode. (c) Place naked electrode at centre of pit. (d) Start refilling empty space around electrode with backfill compound in layers. (e) Pour some water and poke the pit with a long wooden rod to allow trapped air to escape. (f) Gradually continue refilling process till electrode is buried in the pit up to the green patch painted on the top portion of electrode. (g) Ensure that pit is not watery (h) Pack electrode with compound nicely and tightly, so that it stands firmly in pit. (j) Pour a few buckets of water around pit. (k) Pour a few buckets of water around in the pit everday for 10-15 days for system to set. (l) Connect the earth electrode with equipments by 25mm x 3mm aluminium strip. (m) Earthing test point terminal block made of gun metal size 150x100x50 mm drilled and screwed including 4 Nos 8 mm dia 40 mm long hexagonal head bolts and washers duly fixed on walls with fasteners 4 Nos. Note : (a) Earth resistance shall not be more than 5 Ohm. (b) Aluminium strip for connections shall be measured and paid separately.

Taking out existing earthings and M&L for replacement of 'Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to equipment by using GI strips of size 32x6 mm as earthing lead by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and 20mm bore "Light' grade GI watering pipe connected to main switch or main control board or GOD or lightening arrester all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Design mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 7.5 metre from top of earth plate.

Supply & fixing Glavanised iron strip 32x6mm buried in ground.

Earthing with Galvanised iron earth plate electrode 600mm x 600 mm & 6 mm thick burried directly in ground (earth pit not less than 2.25 metre deep below normal GL) with top of earth plate not less than 1.5 metre below GL, connected to GI earth lead wire 4 mm dia connected to earth plate electrode by means of GI nuts, bolts & washers earth wire protected with & including 15 mm bore medium grade ISI marked GI pipe not less than 7.5 metre long all as shown in electrical plate No 3 of MES Schedule Part I, with & including; PCC 1:3:6 type C1 pit with cover of RCC 1:2:4 type B1 reinforced with welded steel wire fabric not less than 4 Kg per Sq M, watering arrangements with 20 mm bore GI medium grade pipe ISI marked , GI funnel with GI mesh, filling with mixture of common salt & charcoal, necessary excavation and earth works in any type of soil, including test point, testing & commissioning, complete.

S&F glow shine board size 18’x3’ made out of 24 gauge GI sheet and front with acrylic sheet total enclosed with computerised letter writings of size not less than 100mm as decided by Engineer-in-Charge and inside with 4’ long 02 Nos of 36w tube light fitting complete with time control switch, MCB and battery back up with timer and synchronised motor board including wiring should be fix on 40mm bore medium grade pipe. The height of board from ground level is 7’ (upto top) and the bottom of the board is 4’. The pole embedded in PCC 1:2:4 type B-1 using 20mm graded agg of size 450x450x600mm with complete service connection of 2.50 Sqmm 3 core copper sheathed cable 10 metre long including protection pipe service connection from the pole by means of 25mm dia light grade pipe to the board including excavation, returning filling and removing out surplus soil all as specified and as directed by Engineer-in-Charge.

Taking out old unsv and Supplying, fixing and testing of cast steel Sluice valve PN1.6 as per IS-14846, body, dome, wedge-CI IS:210, rings-bronze IS:318, Spindal-SS IS:6603, Gland Paking greasy jute packing, fasteners-CS, Gasket- Natural rubber, nominal size DN-150 mm, both ends flanged in existing line, after removal of old unserviceable sluice valve without damaging to existing pipe line complete all as specified and directed by Engr-in-charge. Note : Suitable size flanges for existing pipe line, Joints and jointing materials shall be included under this item.

All as per serial item No. 25 here-in-before but nominal size DN-100 mm -ditto-.

All as per serial item No. 25 here-in-before but nominal size DN-80 mm -ditto-.

S&F Cast iron Non Return valve W/O by pass arangement , Swing type, of Size 100 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one .

S&F Cast iron Non Return valve W/O by pass arangement , Swing type, of Size 150 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one .

Supply and fix Cast Iron Air Release Valves with two air Outlets, conforming to IS 14845 of size 100 mm dia bore and fixing up in Cast Iron Water supply mains of size 100 mm dia.

Supply and fix Cast Iron Air Release Valves with two air Outlets, conforming to IS 14845 of size 150 mm dia bore and fixing up in Cast Iron Water supply mains of size 150 mm dia.

Construction of brick masonary pit of size 60 x 60 x 60cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1. (original date - 30.11.93 and revised date - 15.09.2000 ) Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli.

Construction of brick masonary pit of size 90 x 90 x 90 cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1 (original date - 30.11.93 and revised date - 15.09.2000 ) Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli.

Construction of brick masonary pit of size 120 x 120 x 120 cm internal size with MS sheet 3 mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1 (original date - 30.11.93 and revised date - 15.09.2000 ) Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli.

Supply of calcium hypo chloride, 65%-70% chlorine content, high strength granular disinfectant for treatment of drinking water complete all as specified and qty as per requirement and as directed by Engr-in-Charge.

S&F in replacement of Bronze gate valve for 15mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, fixed as in repair complete all as specified and directed.

All as per serial item No. 47.00 here-in-before but of size 20mm bore -ditto-.

All as per serial item No. 47.00 here-in-before but of size 25mm bore -ditto-.

All as per serial item No. 47.00 here-in-before but of size 40mm bore -ditto-.

All as per serial item No. 47.00 here-in-before but of size 50mm bore -ditto-.

Taking out unserviceable/defective/damaged/blockage GI/MS pipe 40 mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and as directed. (Note: Exacavation and earhwork shall be measured and paid for separately).

All as per serial item No. 52.00 here-in-before but of size 50mm bore -ditto-.

All as per serial item No. 52.00 here-in-before but of size 80mm bore -ditto-.

All as per serial item No. 52.00 here-in-before but of size 100mm bore -ditto-.

S&F steel water tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 40mm bore with and including all fittings such as bends , elbows,tees, short length , socket, union, check nuts, nipples and weldings etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed.

All as per serial item No. 56.00 here-in-before but of size 50mm bore -ditto-.

All as per serial item No. 56.00 here-in-before but of size 80mm bore -ditto-.

All as per serial item No. 56.00 here-in-before but of size 100mm bore -ditto-.

Amount of credit of Rs. 63808.60 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

Pankaj Traders

NARINDER KUMAR SONS