GE 874/EWS-62/2021-22

Amount

B/R and E/M Portion

Demolition of cement conc (Un-reinforced ) in ground floors and pavings n.exc. 15cm thick. (below or above ground level).

75mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or floor complete all as directed by Engr-in-Charge.

M&L for plain cement concrete of type C-1, 1:3:6 (20mm graded aggregate) as in coping, lintel bands, strings coarses etc slightly rounded and chamferred angles and throating etc and setting in mortar complete with joints to match, all as specified.

M & L for Cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) in surface channels and drain, all as specified and directed.

M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement, including forms, moulds etc

M&L Non skid ceramic coloured tiles 7-8 mm thick,area exc 0.11sqm but nexc 0.18 sqm of each tile in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile on 15mm thick screed bed in Cement Mortar 1:4 over 25mm thick PCC 1:2:4 type B0 (using 12.50mm graded crushed stone agg).

M&L for 20 cm x 20cm x 25 mm thick Chequered cement concrete tiles (in any colour & shape), set, jointed and pointed in neat cement slurry in floors with grey cement & no pigment over 20 mm screed bed in Cement Mortar 1:6 complete all as specified & directed.

M&L 50 mm thick PCC 1:3:6 type C-2 (using 20 mm graded crushed stone aggregate ) as in plinth protection finished even aned fair without using extra cement all as specified.

Dismantling of floor, hearth or wall tiling including cement mortar bedding removing rubbish off the premises complete all as directed.

M&L for coloured glazed ceramic tiles as in skirting/ dado (350x250 or 450x350) x 7mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match colour of the tile over backing coat/screed bed 10mm thick in CM1:4 on fair faces of brick/stonewall surffaces for laying dado/skirting complete all as specified and directed by Engr-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering including necessary scaffolding, any type, any location/height complete all as specified and directed by Engr-in-Charge.

S&F prepainted galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering/cladding to wall, fixed with self tapping screw including necessary scaffolding, upto four storey bldg complete all as specified and directed by Engr-in-Charge. (Note : Cost of scaffolding wk for fixing of roof sheet to be included in the unit rate quoted by tenderer)

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including necessary scaffolding, upto four storey bldg complete all as specified and directed by Engr-in-Charge. (Note : Cost of scaffolding wk for fixing of roof sheet to be included in the unit rate quoted by tenderer)

Dismantling timber scantling 40 Sqcm and over in section in any position in unframed work.

M & L second class soft wood in scantling clean swan below or above ground level upto four storey bldg, complete all as specified and directed by Engineer-in-Charge.

All as per item above but except timber.

Dismantling wall and ceiling boards or insulation boards/slabs/blankets, any thickness including cover fillet.

M&L plywood grade BWR type BB, 6mm thick fixed with nails to timber frame work in ceiling.

M&L plywood grade BWR type BB, 6mm thick fixed with nails to timber frame work in lining.

All as per item above but except plywood.

M & L Plain fillets 2nd class soft wood of exc. 3 & n exc. 6 Sqcm, square rectangular or triangular in section , clean swan, secured nails.

M&L for Preparation of newly un treated surfaces and applying two coat of synthetic enamel paint pver a coat of pink primer on wooden surfaces of any description not other wise described over 10 cm width or grith etc complete all as specifed and as directed.

M&L for Preparation of old painted surfaces and applying one coat of synthetic enamel paint on wooden surfaces of any description not other wise described over 10 cm width or grith etc complete all as specifed and as directed.

M&L for Preparation of old painted surfaces and applying two coat of synthetic enamel paint on steel surfaces of any description not other wise described over 10 cm width or grith etc complete all as specifed and as directed.

Dismantling of boarding of any description fitted in any position with nails.

S&F 20mm thick 2nd class softwood boarding, planed one side, with butt joints and fixed with nails in facia eaves boarding complete all as specified and direced by Engr-in-Charge.

M&L 2nd class softwood weather boarding clean sawn, plain 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps.

Description all as per item above, but except boarding, complete all as specified and directed.

Demolition of brick/stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashler facing, dressed stonework and precast concrete articles.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:4 Complete all as specified and as directed.

M&L for Random rubble masonry using sand stone uncoursed well bonded bedded and solidly hearted built in Cement Mortar 1:4 complete all as specified and directed.

all as per item above but except stone.

Taking down of cement plaster of any description including racking out of joints hacking for keys and scrubing down with water etc.

M&L for Rendering 15mm thick on stone/brick masonry surfaces or other than fair faces in cement motar 1:4 finished even and smooth without using extra cement.

M&L for Preparation new or undecorated surface of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specifed and as directed.

S & F in repair Vitreous China Urinal, Half stall type, white with grating and union for discharge pipe including providing and fixing plugs with and including 60mm long brass screws, pointing around urinal back in cement with PVC 32mm dia waste pipe & waste coupling incl spreader complete all as specified.

S&F in repairs Vitreous China Wash down water closet pan (Pedestal pattern), white incl plastic water closet seat and cover closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device & incl P or S trap and connection to trap and to the flushing system anti syphonage pipe etc (excluding flushing cistern and flush pipe) complete all as specified and as directed

S&F in repairs Vitreous China Ware Wash hand basin white flat back size 550mmx400mm including pedestal, cutting for and pinning ends of brackets or erecting stand including necessary PVC outlet pipe, CP coupling 32mm dia complete all as specified.

S&F in repairs vitreous china squatting pan 'Orissa' pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing system anti syphonage pipe etc complete all as specified and as directed

S&F in repairs PVC valveless, syphonic action type, low level PVC flushing cistren 10 ltr cap white with flush pipe & all fitting complete all as specified.

S&F Stop valves cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore pipe,in repair.

S&F Bib taps cast copper alloy ,chromium plated,with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule of 15mm bore, in repair.

S&F in repairs pillar tap cast copper alloy, fancy type with capstan heads chromium plated screwed down with high pressure with or without lettered hot or cold with long screwed, shanks and fly nuts screwed for iron pipe 15mm dia complete all as specified and as directed.

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws.

S&F in repairs Chromium plated shower roses with or without swivel joints, any size,including fixing to steel pipe or union complete all as specified.

S&F in repairs Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F 1000 Ltr capacity PVC water storage tank (cylinderical vertical with closed top ) and fixed in position all as specified in SSR Part -I, including dismantling of old tank .

S&F in repair ball valves, high pressure,with polythene float and flynut complete, 20mm bore.

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head, screwed both ends.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm.

S&F in repair Grating doom 100mm dia of PTMT (minimum weight 25gms) suitable for floor taps, all as specified and directed.

S&F in repairs health faucit (hand shower) cromium plated complete all as specified and as directed. Make : Jaquar or equivalent.

S&F in repairs central hole basin mixer chromium plated 15 mm including 18 inch long braided pouch connection with brass nuts complete or as specified and directed; Make: ESSCO or its equivalent.

S&F in repairs wall mixer cromium plated 3 way including telephonic shower all as specified. Make: Jaquar or equivalent.

S&F in repairs cabinet mirror of size 450mm x 350mm made with 5mm thick PVC sheet, coloured and fixed to wall all as directed by Engr in Charge. Make: prayag or equivalent.

S&F in repairs towel ring of brass chromium plated complete all as specified and as directed

S&F in repairs kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx460mm bowl size 410 mmx330mmx 160mm etc complete all as specified and as directed.

S&F in repairs Stainless steel kitchen plate rack of approved make, size not less than 900mm x800mm complete all as specified.

Taking up or down 15mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 25mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 40mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 50mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 80mm dia GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F GI tube 15 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tube 20 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tube 25 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tube 40 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tube 50 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F GI tube 80 mm dia medium grade galvanished with all fittings laid in floors /wall etc. complete all as specified and as directed.

S&F 15mm bore gun metal globe or gate valve with iron wheel head, screwed both ends.

S&F 25mm bore gun metal globe or gate valve with iron wheel head, screwed both ends.

S&F 40mm bore gun metal globe or gate valve with iron wheel head, screwed both ends.

S&F GI Union for 15mm bore pipe complete all as specified and directed.

S&F GI Union for 20mm bore pipe complete all as specified and directed.

S&F Sanitary fittings of GI Fittings for 15mm bore GI pipe such as Elbow, Socket, Nipple, Plug etc complete all as specified and directed.

S&F Sanitary fittings of GI Fittings for 20mm bore GI pipe such as Elbow, Socket, Nipple, Plug etc complete all as specified and directed.

Lagging to pipes 15mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh and covered with 0.01mm aluminium foil, complete all as specified.

Lagging to pipes 20mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh and covered with 0.01mm aluminium foil, complete all as specified.

Lagging to pipes 25mm bore used in internal water supply or plumbing all round with 25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144Kg/Cum conforming to IS-9842 provided with chicken mesh wire netting 25 gauge, 20mm mesh and covered with 0.01mm aluminium foil, complete all as specified.

Dismantling of rain water pipe and sewage line pipe of any type and any size including fitting complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls

S&F 75mm dia PVC (SWR) pipes single socketed, in any length fixed to walls / floors or in trenches

S&F PVC (SWR) bends any radius, 110mm bore, fitted with oval access door.

S & F bend suitable for 110mm dia PVC (SWR) pipe complete all as specified and as directed.

S&F PVC (SWR) bends any radius, 75mm bore, fitted with oval access door.

S&F PVC (SWR) reducers any radius 110mm bore.

S&F 110mm bore PVC (SWR) junction, single (single T) equal or unequal with door access.

S&F 110mm bore PVC (SWR) junction, single (single Y) equal or unequal with door access.

PVC (SWR) vent cowl 75mm dia.

M&L PVC(SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent cement.

Outsourcing of manpower (2 Safaiwalas daily) to provide services of cleaning of blockages of sewage lines of any dia and depth, manholes of any size and depth, working in foul condition cleaning of manholes and sewage lines by rodding to and fro, flushing with water in sewage lines between successive manholes and keeping the system functional including water closets, floor traps, Nahani traps, gully traps etc, upto final drop/outlet into septic tanks, Dewatering contaminated/ with fine waste material sludge from septic tank and soakage well of any capacity/depth, Cleaning of septic tanks of various capacities including chambers, outlet chambers and removing out all waste solid material / sludge by mean of manually or mechanically and disposing the same to a distance n.exc. 50 mtr and burring in borrow pit within te premises complete incl covering with fresh mud, finally spraying unslaked lime, dry, aroung the septic tank, soakage well and over the pit complete, including cleaning of soil/waste/vent pipes and rain water pipes of any description and size in the area of Drugmulla (lower/upper) Grn by two Semi-Skilled/unskilled Tradesman, (having minimum educational qualification of matriculation) and in one shift of eight Hours per day (from 900 Hrs to 1700 Hours) for attending complaints of sewage cleaning as instructed by concerned JE with complaint slip and report back to the same JE, including maintaining of the record of complaint slips after getting signature of users, complete all as specified and as directed by Engineer-In-Charge.(Cost of earth work in the pit is deemed to be incl in the unit rate quoted by the tenderer)

Cleaning of sewage lines of 100mm /150mm bore including manholes by means of cleaning rods through manholes to manholes, incl dewatering (if any) taking out sludge collected in manholes, depositing the same in the pit at a minimum distance of 50 m from nearby living accn and covering the sludge in pit with earth and finally spraying unslaked lime, dry , around the manholes and cover the pit, out of Garrison in a closed container if living area/Cook house/Office complex not less than 50m from where work is progressed complete , all as directed ( Cost of earth work in the pit is deemed to be included in the unit rate quoted by tenderer).

Cleaning/removal of blockage and removing deposited sludge/liquid materials, foreign materials from manholes, pipe lines through vaccum pressure Jet Machine complete all as specified and directed.

Repairs to Punctures of pipe line including excvation in soft/loose soil, bedding, relaying of pipe and make good the earth excavated incl redressing complete all as specified and directed.

Cleaning of blockage from Water Closet (Indian or European), trap & CI pipe line upto first manhole manually by rodding and removing the deposited sludge/solid/liquid material outsiode MD land, complete all as Specified and as directed by Engr-in-Charge.

Cleaning of blockage from Floor/Nahni trap of kitchen/Bathroom upto but excluding gully trap manually by rodding and removing the deposited sludge/solid/liquid material outsiode MD land, complete all as Specified and as directed by Engr-in-Charge.

Dewatering/pumping/bailing out contaminated with waste material sludge from septic tank along with inlet outlet chamber of any capacity/depth and disposing same out of cantonment area in a closed container including taking off manhole covers and putting back the same after cleaning/removing the liquid waste material of septic tanks and cutting holes through slab/ wall where required for inserting pipe and making good the same with cement morter to match with existing surfaces to make hygienically fit, writing the date of cleaning of spetic tank with black and white paint of size 150 x 200mm and finally spraying unslaked lime (bleaching powder), dry, around and over the septic tank all as directed and the entire satisfaction of by Engr-in-Charge. Note :- 1. Qty of liquid sludge shall be measured for payment under this item. 2. Arrangement of land for the disposal of waste is complete responsibility of contractor.

Demolition of cement conc (reinforced ) in ground floors and pavings n exc. 15cm thick.(Below or above ground level).

M&L Precast Cement Concrete (1:2:4) type B1 using 20mm graded aggregate as in landings, cover slab (for manhole etc), chullah hoods, chajjas, water troughs,shelves and similar articles with plain faces set in Cement Mortar (1:4).

Mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed ) not less than 0.9mm die or securing with clips quality.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

S&F point wiring for one light/fan/bell /5Amp socket outlet independant board point, controlled by one, one way switch with 1.5 sqmm size, PVC insulated and unsheathed 1100 volts grade, single core stranded (multistrand) copper conductor (FRLS) cable drawn into & including midium grade casing caping/PVC conduit (not less than 20mm outer dia) with all fittings and accessories fixed concealed/ surface (including chase cutting in brick/stone masonry walls for fixing conduit/ casing caping and plastering the external surface and matching the same with existing surface) and sunk cast iron or pressed steel terminal boxes for mounting fittings like switches, sockets & fan regulators etc with 3mm thick plastic laminated sheet covers fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.5 sqmm solid copper conductor cable earth wire and connected to earth dolly complete all as specified and directed, are as follows make of cable Havells, Rallison, HPL, RPG.

All as per item above but One switch socket cobination 5 pins 5 amps controlled by one switch on same board.

All as per item above but wiring with 2.5 sqmm copper wire (FRLS) and 1.5 sqmm earth wire for switch socket Combination 6 pin 15 amps on independent board.

S&F switch piano flush button single pole, one way 5 amps complete all as specified and directed. Make - Anchor/SSK/Cona Havells.

S&F switch socket Combination multi 5 pins 5 amp, complete all as specified and directed. Make - Anchor/SSK/Cona Havells.

S&F switch socket Combination 2 in 1, 6 pins 15 amp, complete all as specified and directed. Make - Anchor/SSK/Cona Havells.

S&F ceiling rose, PVC/poly carbonate, isolated body three terminal complete all as specified and directed. Make - Anchor/SSK/Cona Havells.

S&F only stepped type electronic fan regulator 1 module in white colour. Make : Anchor/Cona/SSK.

S&F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed. Make - Anchor/SSK/Cona Havells.

S&F sheet metal enclosure for DBs (double door type) when MCBs to be used single pole and neutral 8 way incl blanking plate as reqd with 200 amps rated busbar 240V fixed sunk/flush to the wall or niche complete all as specified and directed. Make : Legrand, Havells/HPL.

S&F sheet metal enclosure for DBs (double door type) when MCBs to be used single pole and neutral 4 way incl blanking plate as reqd with 200 amps rated busbar 240V fixed sunk/flush to the wall or niche complete all as specified and directed. Make : Leggrand/Havells/HPL.

S&F MCB's single pole 240 volts 6 to 32Amps 10 KA 'C' series, all as specified and as directed by Engr -in-Charge. Make : Leggrand/Havells/HPL.

S&F MCB SPN, 32 Amp, 10 KA, 230 Volt. Make : Leggrand/Havells/HPL.

M & L for sub main wiring with two single core 4 sqmm PVC insulated and unsheathed 1100 volts grade, stranded copper conductor (FR) ISI marked drawn into & including medium grade PVC conduit 25 mm dia with all fittings and accessories fixed concealed including chase cutting in brick/stone masonry walls for fixing conduit and plastering the external surface and matching the same with existing surface and one continuous run of 4 sqmm copper conductor PVC insulated (green colour) as earth wire fixed into PVC conduit complete all as specified and directed.

M & L for sub main wiring with two single core 2.5 sqmm PVC insulated and unsheathed 1100 volts grade, stranded copper conductor (FR) ISI marked drawn into & including medium grade PVC conduit 25 mm dia with all fittings and accessories fixed concealed including chase cutting in brick/stone masonry walls for fixing conduit and plastering the external surface and matching the same with existing surface and one continuous run of 4 sqmm copper conductor PVC insulated (green colour) as earth wire fixed into PVC conduit complete all as specified and directed.

Taking down unserviceable FTL and S&F LED, 20 Watts, 4 ft, fittings complete with all accesories for mounting light fittings complete including replacment of old US ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body. Make of light fitting - Phillips/C & S/Wipro. Make of ceiling rose : Leader/ Cona/Anchor.

Taking down unserviceable FTL and S&F LED Integrated batten T8 type, 10 Watts, 2 ft, white, indoor decorative aluminium extruded complete with two nos of PVC box of size 75x75x20mm for mounting light fittingscomplete.including replacment of old US ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body. Make of light fitting - Phillips/C & S/Wipro. Make of ceiling rose : Leader/ Cona/Anchor.

Taking down unserviceable FTL/Bulk Head and S&F LED Bulk Head light, 10Watts IP55 in engineering plastic housing with clear prismatic diffuser. including replacment of old US ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body. Make of light fitting - Phillips/C & S/Wipro. Make of ceiling rose : Leader/ Cona/Anchor.

Supply and fixing recess mounting luminaire with high brightness LEDs as light source, 36W (2x2ft Panel Light) suitable for Armstrong/Grid ceiling complete all as specified. Make : Havells.

Supply only self Adhesive electrical insulation tape of size 2.5cm x 25m x 0.125mm, ISI marked. Make : Steelgrip/Kinjal/SSK.

Supply & fixing LED lamp energy saving 10W LED lamp 6500 K Make Suriya, Crompton greaves, Bajaj.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 03 of 2009 SSR Pt-I and testing on complete including earth work in any type of soil, PCC 1:2:4 type B-0 as in earth pit and cover 40mm thick reinforced with XPM (weight not less than 4.0Kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, common salt, charcoal and testing on completion, all as specified and directed.

Supply only Distiled water for Battery (Exide) of 12V & 24V.

Supply only Cable Jointing Kit for 11KV (Earthed) grade cable for indoor termination heat shrink type point complete with jointing material and accessories suitable for 3 core XLPE Armoured alluminium conductor cable of size 16sqmm to 35sqmm.

All as per item above but for cable size 50sqmm to 95sqmm.

All as per item above but for cable size 120sqmm to 185sqmm.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 2 core 10 sq.mm nominal cross section in service connections.

Excavation in trenches not exc.1.5 mtr wide and not exc.1.5 m in depth for foundation of poles, stay assembly and laying of LT cable as in any type of soil and getting out, complete all as specified and directed.

Returning, filling, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in any type of soil, complete all as specified and directed.

Removal of excavated material to a distance not exc.50 m and depositing where directed at a level not exceeding 1.5 mtr above starting point.

M&L Clear dry and sharp sand as in cushioning layer over and under cable laid in trenches complete all as specified and directed.

Sub class ‘B’ common burnt bricks, old size designated 75 laid dry flat with width equal to length of bricks as cover laid over the cable to give mechanical protection to under ground cable all as specified and directed.

Plain Cement concrete 1:2:4 type B-2 using 40 mm graded crushed stone aggregate as in pole coping and stay assembly all as specified directed.

Plain Cement concrete in foundation of poles streets and stays 1:3:6 type C-2 using 40 mm graded crushed stone aggregate all as specified directed.

Supply, laying and testing in replacement of XLPE insulated screened, PVC bedded galvanized steel strip or wire armoured, electric power cables (heavy duty) with aluminum conductor 1100 volts grade, cross section area 70 Sqmm, 4 core complete all as specified and directed. Make:- Havell's/ Fort Gloster/Poly Cab.

S&F 1100 volt grade heavy duty cable PVC insulated multistranded aluminum conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire one 2 core cable flat or circular of size 10 Sqmm incl taking down old service connection and removing from the side complete all as specified and as directed. Make:- Havell's/ Fort Gloster/Poly Cab.

S&F in replacement of GI pipe light grade 40 mm bore for cable protection fixed on poles or laid in trenches under floor, ducts etc with fixing clamps, nuts bolts etc all as specified. Make: Prakash Surya/ Jindhal/ Kalinga

All as per item above but 25 mm bore.

S & F in replacement steel tubular swaged poles erected truly vertical or planted as strut complete with 300 x300x 6 mm thick mild steel base plate, welded to pole, B-118 final, taper cap, bolts, nuts & screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II. type 410 SP-55 (9.0 metres long) including drilling of holes of reqd size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminium paint over a coat of red oxide zinc chrome primer and with two coats of black bitumenous paint internally & portion embedded in concrete, making five black & red bands at lower portion of pole each 300mm wide alternately, and making pole No. with black paint at suitable height all as specified and directed.

S&F in replacement of Cross arms, bracing, supports clamps and back plates, fabricated from structural steel sections incl nuts, bolts, washer, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed incl one primer, one under coat and one finishing coat of aluminium paint over prepared steel surface.

M&L in replacement of Shackle type, porcelain, vitreous, white, brown or green insulators for working pressure 1100 volts grade, 90 mm dia 75 mm height including galvanized mild steel straps of 31 x 3 mm size, 12 mm dia insulator bolts, washers and nuts complete all as specified.

M&L in replacement of Pin type porcelain vitreous white brown or green insulator including one galvanized mild steel spindle, two galvanized iron, washers and one galvanized iron nut, 100 mm height, 65 mm dia for 1100 volt grade all as specified.

Supply Only of on load changeover switch 415 volt in sheet metal enclosure 4 pole of capacity 100,160& 250 Amp (as required) complete all as specified and directed by Engr-in-Charge.

Supply only of off load changover switch 415 volt in sheet metal enclosure 3/4 pole of capacity from 100,160& 250 Amp (01xeach) complete all as specified and directed by Engr-in-Charge.

M&L for Painting to LT poles, 9 mtr with cross arms, bracing and clamps with one coat of synthetic enameled paint over one coat of red oxide primer including scrapping the old paint carefully to make smoothen complete and painting strips of red and black from foot of pole upto 5 feet each strip of 30 cm height all as specified and directed.

Restretching of LT /HT ACSR conductor and GI wire of any size and on any type of poles carrying upto six conductors in a span including disconnecting from insulator and rewinding to insulator after stretching with and including aluminium wire including re-fixing/re-adjusting line spans, line separators, cross arms on poles all as specified.

Cutting /Trimming/ Chopping of tree trenches along the overhead lines upto 3 m from elect lines clearance on both sides of HT/LT lines and disposing off the cut tree/ branches site to a distance not exc. 50 m and clearing the site as directed.

Supply and fix cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination , heat shrink type, joint complete with jointing material and accessories suitable for 4 core XLPE /(ABC), armoured, Al conductor cable of size 50 sqmm 95 sqmm

Earthing complete with galvanised steel earth plate electrode 60cm × 60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth strip 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion.

Supply only copper thimble of size 50sqmm, all as specified and directed.

Supply only copper thimble of size 70sqmm, all as specified and directed.

Supply only copper thimble of size 95 sqmm, all as specified and directed.

Supply only copper thimble of size 120 sqmm, all as specified and directed.

Material and labour to repair unserviceable LED Street Light/ Search Light of 40 to100Watts, including replacement of driver with a new driver (having surge protector and lightning protector) with input Voltage variation between 140V to 300V (voltage in this region will not be considered as surge voltage), with after repair warranty of two years.

Supply only of suitable LED driver (having surge protector and lightning protector) with input Voltage variation between 140V to 300V (voltage in this region will not be considered as surge voltage) for LED Street/ Search Lights upto 40 to 100 Watts, with warranty of two years.

Supply and fixing LED street light fitting 1x70 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass, with LED tube light fixtures driver, holders, connector,GI bracket bend to shape, nuts & bolt etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size.

M&L in replacement of ACSR conductor of any size and any type including stretching, fixing and binding to insulator on OH LT line service feeders all as specified including aluminium binding wire or aluminium tapes complete all as specified. This item includes all consumables (such as binding wire and replacement insulators and cross arms, etc., for replacement of damaged ones found after/ during replacement process).

Supply and replacement of MCCB 160 Amp 4 Pole 415 Volt breaking capcity 36kA. Make Havells or Equivelent Make of L & T or C&S.

Supply and replacement of MCCB 200 Amp 4 Pole 415 Volt breaking Capacity 36kA. Make Havells or Equivelent Make of L & T or C&S.

Supply and replacement of MCCB 250 Amp 4 Pole 415 Volt breaking Capacity 36kA. Make Havells or Equivelent Make of L & T or C&S.

Supply and replacement of MCCB 400 Amp 4 Pole 415 Volt breaking Capacity 36kA. Make Havells or Equivelent Make of L & T or C&S.

RATHER BROTHERS

M/S ABDUL AHAD SHAH

Bidder Name

M/S ABDUL AHAD SHAH

RATHER BROTHERS

M/S BEE AAY CONSTRUCTIONS