Loading
Loading…
Loading…
Tender Value
₹1.2 Cr
EMD Value
₹2.1 L
Closing Date
7 Apr 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DRAWING
29 conditions · 9 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies / PSUs authorities. Certificates issued by Private Bodies will not be considered.
(b) Audited Balance Sheets clearly indicating contractual receipts from the works done for Govt./ Govt. bodies / PSUs/Pvt. Organization in the P&L Account of the balance sheet duly certified by the Chartered Accountant for the completed & current Financial years.
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31 st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above. (ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii) Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets. (iv) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfilment of the Para No.17.15.2 of part-I of IRSGCC- 2019 for J.V guide lines (with upto date correction slip).
NOTE: If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
The individual / firm should have minimum valid "B" grade electrical license or above and should be on their own name/Firm name issued by t h e Electrical Inspectorate of the respective State Electrical Licensing Board". The License should have been issued on a date prior to the date of Tender opening. Clear scanned copy is to be submitted along with the tender. A copy of license should be uploaded through IREPS with their offer, failing which the tender will be rejected
Similar Nature of work: "Works of wiring/cabling or installation and commissioning of electrical items (other than on coaches) such as lights, fans, pumps, charging arrangements, earthing etc (with or without supply of items/equipments) for 230V, 1phase or 415V, 3phase system or higher voltages". a copy of similar nature of work should be uploaded through IREPS with their offer, failing which the tender will be rejected.
94 conditions · 9 needing a document upload
TENDER SHALL BE REJECTED if it is not accompanied by the following:
Cost of tender document & EMD deposited through IREPS e- payment
In case of Partnership firm : The tender form shall be submitted only in the name of partnership firm.
In case tenderer is JV Firm : The tender form shall be submitted 1.1.2 only in the name of the JV and not in the name of any constituent member.
Uploading of Certificate in support of Technical Eligibility (As detailed in Standard Technical Criteria).
Submission of Certificate(s) in support of Financial Eligibility (As detailed in Standard financial criteria).
IN CASE OF ADVERTISED TENDER VALUE IS MORE THAN RS. 20 CRORES: Bid capacity is applicable, the tenderers should submit proforma attached in DOCUMENTS. In case, the tenderer/s failed 1.3.1 to upload BID CAPACITY PROFORMA along with offer, their/his offer shall be considered as incomplete and will be rejected summarily.
In case tenderer is other than sole proprietorship firm, following documents shall be uploaded by the tenderer:
In case the Tenderer is a Partnership Firm: [i] Partnership deed . [ii]Power of Attorney (duly registered as per prevailing law) in favour of an individual to sign the tender documents and create liability against the Firm. [iii] PAN / TAN number of Partnership firm (PAN / TAN number in the name of any of the constituent partners shall not be considered). [iv]An undertaking by all partners of the partnership firm that they are not blacklisted or 1.4.1 debarred by Railways or any other Ministry / Department of the Govt. of India / any State Govt. from participation in tenders / contracts as on the date of opening of bids, either in their individual capacity or in any firm in which they were / are partners. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the General Conditions of Contract
In case the Tenderer is a LLP Firm registered under LLP Act-2008 (i) a copy of LLP Agreement, (ii) a copy of Certificate of Incorporation; and (iii) a copy of Power of Attorney/Authorisation 1.4.2 issued by the LLP Firm in favour of the individual to sign the tender on behalf of the LLP Firm and create liability against the Firm. (iv) copy of PAN number of the LLP Firm
In case the Tenderer is a Company registered under Companies Act-2013:(i) the copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company; and (ii) A copy of 1.4.3 Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.(iv) copy of PAN number of the Company.
In case the Tenderer is a Registered Society & Registered Trust: (i) a copy of the Certificate of Registration, (ii) Deed of Formation; and (iii) a copy of Power of Attorney in favour of the 1.4.4 individual to sign the tender documents and create liability against the Society/Trust. (iv) copy of PAN number of the Society/Trust.
Incase JV Firms are allowed to participate: Uploading of MEMORANDUM OF UNDERSTANDING as per the format given in "Documents attached with tender" and also below documents.
In case one or more members is/are Proprietary Firm or HUF, the following documents shall be enclosed:: A copy of notarized affidavit on Stamp Paper declaring that his/her Concern is a 1.5.1 Proprietary Concern and he/she is sole proprietor of the Concern OR he/she is in position of "KARTA" of Hindu Undivided Family (HUF) and he/she has the authority, power and consent given by other partners to act on behalf of HUF.act on behalf of HUF.
In case one or more of the members of the JV is/are partnership firm(s), following documents shall be submitted:]:(a)A copy of the Partnership Deed, (b)A copy of consent of all the partners or individual authorized by partnership firm, to enter into the Joint 1.5.2 Venture Agreement on a stamp paper, (c)A copy of Power of Attorney (duly registered as per prevailing law) in favour of the individual to sign the MOU/JV Agreement on behalf of the partnership firm and create liability against the firm.
In case one or more members of the JV is/are companies, the following documents shall be submitted: (a)A copy of resolutions of the Directors of the Company, permitting the company to enter into a JV agreement, (b) A copy of Memorandum and 1.5.3 Articles of Association of the Company. (c) A copy of Authorization/copy of Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender, sign MOU/JV Agreement on behalf of the company and create liability against the company.
IN CASE THE TENDER VALUE MORE THAN RS. 50 LAKHS; Tenderers shall submit a notarized affidavit on a non-judicial stamp paper stating that all their statements / documents submitted along with bid are true and factual.
Uploading of Declaration regarding Employment of Retired Engineer/Retired Railway Officer as per clause no.17 of Part-I of IRSGCC. [in the format attached in - Documents]
Uploading of NEFT FORM - as per the format attached with the tender document.
The list of personnel / organization on hand and proposed to be engaged for the tendered work.
List of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work.
Uploading of Statement Showing the particulars of Works on Hand & Works Completed as per the format attached to the tender document.
Uploading of certificate by local suppliers in regard to meeting the Minimum Local Content requirement to avail benefits under Public Procurement Policy Order-2017 (A) for procurement order of value less than Rs. 10 crores: self certificate in accordance with Para-9(a) of Public Procurement(Preference to Make in India) Order 2017. (B) For Procurement Order of value more than Rs. 10 crores, the certificate from Statutory auditor/cost auditor/practicing CA as the case may be in accordance with Para-9(b) of Public Procurement (Preference to Make in India) Order 2017.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
IN CASE OF SINGLE PACKET TENDERS; CONSORTIUM AGREEMENTS, JOINT VENTURE FIRMS AND MOUS SHALL NOT BE CONSIDERED
IN CASE OF TWO PACKET TENDERS CONSORTIUM AGREEMENTS AND MOUS SHALL NOT BE CONSIDERED . BUT JOINT VENTURE FIRMS ARE CONSIDERED FOR ELIGIBILITY.
CONDITIONS FOR PARTICIPATION OF PROPRIETARY FIRM / PARTNERSHIP FIRM /PRIVATE LIMITED COMPANY / LIMITED COMPANY/ JV FIRMS:
In case the tenderer is an individual / proprietary concern, the experience and turnover shall be in the name and style of the Individual / Proprietary concern only.
In case the tenderer is a Partnership Firm, the experience and received contractual payments shall be in the name and style of the firm only. The other guidelines at Clause 18 of Part I of 4.1.1 IRSGCC shall be applicable . Note: The partner of a Partnership Firm cannot claim the credentials of Partnership firm to the extent of his share either during the subsistence of the Partnership firm or after its dissolution.
FOLLOWING DOCUMENTS SHALL BE ENCLOSED:
In case the Tenderer is a Partnership Firm: [i] Partnership deed . [ii]Power of Attorney (duly registered as per prevailing law) in favour of an individual to sign the tender documents and create 4.2.1 liability against the Firm. [iii] PAN / TAN number of Partnership firm (PAN / TAN number in the name of any of the constituent partners shall not be considered).
In case the Tenderer is a Company registered under Companies Act-2013:(i) the copies of MOA (Memorandum of Association) and AOA (Articles of Association) of the company; and (ii) A copy of Authorization/Power of Attorney issued by the Company 4.2.2 (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.(iii) copy of PAN number of the Company.
In case of JOINT VENTURE (JV) FIRMS: Clause No.17 of Part-I of IRSGCC with upto date correction slip shall be applicable in all aspects for Participation of Joint Venture[JV] firms in works tenders. JV firm should submit Memorandum of 4.2.3 Understanding[MOU] as per the format attached as annexure to the tender in DOCUMENTS. Submission of all other documents by JV firm / Members of JV should also be as per Cl.No.17.14 of Part-I of IRSGCC.
In case the Tenderer is a LLP Firm registered under LLP Act-2008 (i) a copy of LLP Agreement, (ii) a copy of Certificate of Incorporation; and (iii) a copy of Power of Attorney/Authorisation 4.2.4 issued by the LLP Firm in favour of the individual to sign the tender on behalf of the LLP Firm and create liability against the Firm. (iv) copy of PAN number of the LLP Firm
In case the Tenderer is a Registered Society & Registered Trust: (i) a copy of the Certificate of Registration, (ii) Deed of Formation; and (iii) a copy of Power of Attorney in favour of the 4.2.5 individual to sign the tender documents and create liability against the Society/Trust. (iv) copy of PAN number of the Society/Trust.
Uploading of other relevant documents connected to the tender; such as Declaration regarding employment of Retired Engineer/ Retired Railway officer, NEFT Form, List of Personnel/Organization, List of Plant/machinery, Particulars of works on hand and completed (As per the formats attached in the list of Documents)etc.
Hyderabad Division: 1) STTC: Improvements to Admin building facade and rooms in STTC/MLY- Electrical arrangements 2) STTC: Proposed improvement of hostel building at STTC/MLY- Electrical arrangements 3) STTC: Proposed construction of Store room (11m x 8m) at STTC/MLY- Electrical arrangements
37-HRD-25-26-SrDEE-M-HYB
37-HRD-25-26-SrDEE-M-HYB
Open
Works - General
12 Months
Hyderabad, Telangana
₹0
₹2.1 L
7 Apr 2026
11 Mar 2026
24 Mar 2026
203 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,19,36,996 | ||
| — | 20.00 | — | — | ||
| Dismantling of existing wiring including switch boards, fittings and fans etc., and same item should be handed over to SSE Office | — | — | — | 20,000 | |
| — | 3000.00 | — | — | ||
| Supply & laying of PVC conduit pipe of 32 mm dia 2 mm thick in concealed/surface as per the directions of Engineer at site | — | — | — | 1,65,000 | |
| — | 6400.00 | — | — | ||
| Supply & laying of PVC conduit pipe of 25 mm dia 2 mm thick in concealed/surface as per the directions of Engineer at site | — | — | — | 1,98,400 | |
| — | 480.00 | — | — | ||
| Supply & fixing of PVC conduit moulded bend pipe 32/25 mm dia 2 mm thick in concealed | — | — | — | 13,440 | |
| — | 120.00 | — | — | ||
| Supply & fixing of PVC Junction box of suitable way for 32/25 mm dia 2 mm thick PVC conduit pipe in concealed | — | — | — | 3,000 | |
| — | 1300.00 | — | — | ||
| Supply and laying of flexible 25mm PVC pipe | — | — | — | 23,400 | |
| — | 19700.00 | — | — | ||
| Supply, laying, connecting & commissioning of single core FRLS multi strand 1.5 sq. mm Cu. Conductor | — | — | — | 3,34,900 | |
| — | 14200.00 | — | — | ||
| Supply, laying, connecting & commissioning of single core FRLS multi strand 2.5 sq. mm Cu. Conductor | — | — | — | 3,97,600 | |
| — | 10800.00 | — | — | ||
| Supply, laying, connecting & commissioning of single core FRLS multi strand 4 sq. mm Cu. Conductor | — | — | — | 4,75,200 | |
| — | 2800.00 | — | — | ||
| Supply, laying, connecting & commissioning of single core FRLS multi strand 6 sq. mm Cu. Conductor | — | — | — | 2,63,200 | |
| — | 1320.00 | — | — | ||
| Supply, laying, connecting & commissioning of single core FRLS multi strand 10 sq. mm Cu. Conductor | — | — | — | 1,55,760 | |
| — | 300.00 | — | — | ||
| Supply, laying, connecting and commissioning of 3 core 1.5 mm sq.mm multi stranded FRLS cu. Conductor as per directions of Engineer at site | — | — | — | 17,400 | |
| — | 1670.00 | — | — | ||
| Supply & erection of 6/10A 1-way switch | — | — | — | 1,08,550 | |
| — | 190.00 | — | — | ||
| Supply & erection of 16/20A one way switch | — | — | — | 16,720 | |
| — | 250.00 | — | — | ||
| Supply & erection of 6/10A socket with safety shutter | — | — | — | 21,250 | |
| — | 190.00 | — | — | ||
| Supply & fixing of 16/20/10A socket heavy duty with safety shutter | — | — | — | 26,790 | |
| — | 61.00 | — | — | ||
| Supply & erection of 3 way module size GI sheet metal/PVC box in concealed/surface similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 3,721 | |
| — | 61.00 | — | — | ||
| Supply & erection of 3 module size modular plates with unbreakable frame similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 4,697 | |
| — | 56.00 | — | — | ||
| Supply & erection of 6 way module size GI sheet metal/PVC box in concealed/surface similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 5,376 | |
| — | 56.00 | — | — | ||
| Supply & erection of 6 module size modular plates with unbreakable frame similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 6,832 | |
| — | 57.00 | — | — | ||
| Supply & erection of 12 way module size GI sheet metal/PVC box concealed/surface similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 9,006 | |
| — | 57.00 | — | — | ||
| Supply & erection of 12 module size modular plates with unbreakable frame similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 10,773 | |
| — | 32.00 | — | — | ||
| Supply & erection of 18 way module size GI sheet metal/PVC box concealed/surface similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 6,208 | |
| — | 32.00 | — | — | ||
| Supply & erection of 18 module size modular plates with unbreakable frame similar to GM make or equivalent as per the directions of Engineer at site | — | — | — | 7,744 | |
| — | 1500.00 | — | — | ||
| Supply of 4core 120 mm² LT XLPE Al. UG Cable, 1100 Volts as per IS:7098/Pt.I/1988 or latest | — | — | — | 11,76,000 | |
| — | 1500.00 | — | — | ||
| Laying, connecting, testing and commissioning of 4core 120 mm² LT XLPE Al. UG Cable, 1100 V as per IS:7098/Pt.I/1988 or latest | — | — | — | 75,000 | |
| — | 450.00 | — | — | ||
| Supply of 4core 25 mm² LT XLPE aluminium UG Cable, 1100 Volts as per IS:7098/Pt.I/1988 or latest. | — | — | — | 1,01,250 | |
| — | 450.00 | — | — | ||
| Laying, connecting, testing and commissioning of 4 core 25 sq.mm multi strand LT XLPE cable as per directions of the engineer at site. | — | — | — | 4,950 | |
| — | 600.00 | — | — | ||
| Supply of 4core 16 mm² LT XLPE aluminium UG Cable, 1100 Volts as per IS:7098/Pt.I/1988 or latest. | — | — | — | 1,09,200 | |
| — | 600.00 | — | — | ||
| Laying, connecting, testing and commissioning of LT PVC/XLPE cable of size 4 core 16 Sq.mm | — | — | — | 5,400 | |
| — | 2550.00 | — | — | ||
| Supply and fixing of G.I. wire earth continuity of 8 SWG G.I. wire | — | — | — | 22,950 | |
| — | 1450.00 | — | — | ||
| Supply & erection of HDPE pipe of 110 mm dia, PN-6, PE-100 of material grade as per IS 4984-2016 or latest as per the directions of Engineer at site | — | — | — | 6,30,750 | |
| — | 850.00 | — | — | ||
| Supply & erection of HDPE pipe of 50 mm dia, PN-6, PE-100 of material grade as per IS 4984-2016 or latest as per the directions of Engineer at site | — | — | — | 1,53,000 | |
| — | 2300.00 | — | — | ||
| Excavation of cable trench 30 cm widex90cm deep in all types of soils for LTUG cable as per instruction of engineer at site | — | — | — | 2,99,000 | |
| — | 200.00 | — | — | ||
| Cutting of asphalted road/ concrete/ cement/ under the track etc., and excavation of cable trench 30 cm widex90cm deep road etc., for laying of LTUG cable. After laying of cable the trench should be brought to its original position by providing tar/ concrete/ cement as per the site conditions and as per directions of Rly. Engineer. | — | — | — | 43,200 | |
| — | 11.00 | — | — | ||
| Provision of concrete foundation and constructing the plinth as per the directions of engineer at site. | — | — | — | 44,033 | |
| — | 50.00 | — | — | ||
| Fabrication, supply, laying and fixing of S.S perforated cable tray of size 200 mm x 50 mm x 1.5 mm thickness with cover, SS 304 grade. The cable trays should be fixed on the roof, under COP, wall, with suitable clamps, bolts & nuts etc., firmly and rigidly as per the directions of engineer at site | — | — | — | 1,44,850 | |
| — | 1.00 | — | — | ||
| Design, fabrication, supply, fixing, connecting, testing and commissioning of steel sheet iron cubical type 14 SWG Outdoor IP65 rated Main distribution board with the following switches/ MCCBs including sectionalized copper bus bar of capacity 800 Amps (copper bus bar should be RYBN uniform sizes) along with 1 No. Multifunction meters (bidirectional) and 0.2S class CTs with RS485 port and RYB LED indication lamps with control MCBs and all other connected accessories etc., 2 x 400 4 pole 36KA MCCB Microprocessor based including suitable spreader link, OL(Over Load), SC(Short circuit), Ground fault along with 400A On load change over, 4 x 200/250 4 pole 36KA MCCB Microprocessor based including suitable spreader link, OL(Over Load), SC(Short circuit), Ground fault, 2x125/160 A 4 pole 36KA MCCB Microprocessor based including suitable spreader link, OL(Over Load), SC(Short circuit), Ground fault 6x63A 10KA FP MCB, 10x32A 10kA FP MCB, 4x32A 10KA DP MCB Note: 1) All MCCBs should be Microprocessor only 2) ICs=100% Icu and all cables terminations to be done along with double compression glands and required lugs as per the direction of Engineer at site. | — | — | — | 5,41,517 | |
| — | 47.00 | — | — | ||
| Supply, fixing, testing and commissioning of (DP MCB - Incoming & SP/MCB - Outgoing) wall mounted of one row 12 module circuit breaker box made out of thermoplastic, with N terminal, size (202 x 238 x 111)mm complete. The LT distribution board shall be comprising with the following MCBs fixed in it conforming to IS:8828: 1996, ISS & IE rules and site requirement. DP MCB 40-63 Amps. 'C' series = 01 No. (Incoming) SP MCB 6-32 Amps. 'B' series = 07 Nos. (Outgoing) | — | — | — | 3,53,581 | |
| — | 1.00 | — | — | ||
| Design, supply, installation, testing and commissioning of cubicle type 14SWG LT panel (Indoor type) with 200 amps sectionalized electrolytic copper bus bar (phase RYBN uniform sizes). LT switchgear confirming to IS-8623. Advanced Multi function meters with CTs of suitable capacity with R.S.485 port for incoming supply with CTs of suitable and RYB LED indication lamps with all other connected accessories etc., as directed by Engineer at site. 2x100 A 4pole 35/36KA MCCB (I/C), 1x100A change over switch Out goings: 4x63 Amps RCBO 100mA, 2x16A SP MCB. Note: MCCBs:1) ICs=100% ICu 2) All MCCBs should be microprocessor based | — | — | — | 1,05,494 | |
| — | 16.00 | — | — | ||
| Supply and erection of earth electrode (as per RDSO Drawing No.ETI/OHE/P/7021 & RDSO Spec no. TI0LKO(PSI)/ 38/ 2020 Dt:25.08.2021 or latest) | — | — | — | 1,06,080 | |
| — | 320.00 | — | — | ||
| Supply, laying, connecting & commissioning of 40mm x 5mm/ 25mm x 5mm thick GI Strip for earth pit as per the directions of engineer at site | — | — | — | 22,400 | |
| — | 6.00 | — | — | ||
| Supply, installation, testing and commissioning of surface mounted RGBW Narrow/Medium beam Projector luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover, clear/powder coated. Luminaire luminous flux range 8000-82000 Lm. Luminaire having DMX 512 control protocol capable of producing 16.7 million colour options. The luminaire should have options for various beam angles: 15/25/35. Power consumption should be between 195W to 205W at steady state full intensity. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of pressure Die cast Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition minimum IK08. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +45°C, Operating Humidity: 10%-90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE/ LUMILED/ OSRAM/ SEOUL/ SAMSUNG/ Bridgelux reputed make shall be used for the light fittings. Luminaire Shall be BIS approved. Cat. Ref. Bajaj FL series or equivalent | — | — | — | 3,21,000 | |
| — | 30.00 | — | — | ||
| Supply, installation, testing and commissioning of LINEAR 1000/1200mm RGBW surface mounted Narrow/Medium/Elliptical beam luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with mid/high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric/elliptical distribution. Luminaire luminous flux range 960-1000 Lm. Luminaire having DMX 512 control protocol capable of producing 16.7 million colour options. The luminaire should have options for various beam angles: 8/15/25/35/10x60/15x45. Power consumption should be between 22W to 26W at steady state full intensity. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of Extrusion Aluminium. Impact resistance level should be suitable to site condition of minimum IK08. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +50°C, Operating Humidity: 10%- 90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE/ LUMILED/ OSRAM/ SEOUL/ SAMSUNG/ Bridgelux reputed make shall be used for the light fittings. Luminaire shall be BIS approved. Cat. Ref. Bajaj BA WW series or equivalent | — | — | — | 5,25,000 | |
| — | 30.00 | — | — | ||
| Supply, installation, testing and commissioning of surface mounted RGBW Narrow/Medium beam Projector luminaire suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover, clear/powder coated. Luminaire luminous flux range 2000-2100 Lm. Luminaire having DMX 512 control protocol capable of producing 16.7 million colour options. The luminaire should have options for various beam angles: 15/25/35. Power consumption should be between 48W to 54W at steady state full intensity. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP 66 or higher. Housing should be made of pressure Die cast Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition minimum IK08. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +45°C, Operating Humidity: 10%-90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE/ LUMILED/ OSRAM/ SEOUL/ SAMSUNG/ Bridgelux reputed make shall be used for the light fittings. Luminaire shall be BIS approved. Cat. Ref. Bajaj FL series or equivalent | — | — | — | 6,30,000 | |
| — | 1.00 | — | — | ||
| Supply, installation, testing and commissioning of DMX Controller System with Standalone interfaces. Controller should deliver 2*512DMX channels, the controller should have future upgradation provision up to 4 DMX universe Port. The controller should have new Nicolaudie Stand Alone engine (NSA) offering some great possibilities (multi-zone, extended triggers, 16-bit channels management). The controller should offer multiple possibilities to trigger your lighting scenes: time/date, input ports, TCP/UDP commands. Should have Intuitive backlit keyboard with 10 presets. PC DMX IN triggers: Yes, Standalone DMX IN triggers: External triggers: 10 buttons for direct access, 2 buttons to change scene, + 1 button to change zone. 16 dry contact trigger ports via 20-Pin IDC Socket. Internal calendar: Yes, Backup of the internal clock: Yes, 3 weeks without power, Memory card: Yes microSD card, 32GB max, Input power voltage: 5-5.5V DC 0.6A with power adapter working on AC power supply, via USB (USB power supply included), Trigger lighting scenes using calendar triggers and conditional rules with New Stand Alone engine, using contact ports, RS232 or over Ethernet. Stand alone mode with 99 scenes across 5 zones. Buttons: iPhone/iPad/Android remote and programming apps. Temperature: 0 to +50 C°, DMX Compatibility: 8 and 16 bit DMX fixtures, System Compatibility: Windows XP, Vista, 7, 8, 8.1, 10, MAC OS X. Make: Nicolaudie/ Pharos/ Osram ECUE/ Philips iColor (10.6 and +), Linux: Make: Nicolaudie: SLESA-U11 | — | — | — | 1,40,000 | |
| — | 2.00 | — | — | ||
| Supply, installation, testing and commissioning of DMX Splitter cum Booster, Input Power- 100 to 240 VAC, auto-ranging, 50/60 Hz., Housing rugged aluminium, Operation Temperature -17°C - +55°C (0°F - 131°F), 5/6 output ports with 3/5-pin terminal sockets, each port should be optically isolated, Protection Rating IP20 including connection complete as required. Make: Pioneer/Briteq/Swisson | — | — | — | 1,70,000 | |
| — | 4000.00 | — | — | ||
| Supply, laying, testing and commissioning of 4-pair, Cat6 Solid (Third party ETL Intertek tested 625 MHZ above) to support 1Gbps with Cross (+) filler pair separator & PVC sheath 23 AWG. Compliant in the existing raceways/PVC conduits including making connections to information outlets and patch panels with ferruling at both ends for identification with necessary tools for punching stripping crimping and testing required etc., complete as per direction of Engineer at site | — | — | — | 2,72,000 | |
| — | 100.00 | — | — | ||
| Supply, erection, testing and commissioning of 8W Bollard LED light of height 0.6mtrs for garden lights as per directions of engineer at site | — | — | — | 2,80,000 | |
| — | 200.00 | — | — | ||
| Supply & erection of edge lite LED signage board with suitable LED driver. Operating voltage range is 90-270V AC. Content on the signage is laser etched with legible text/ visible image and aptly suited when LEDs are switched on as per the RDSO specification | — | — | — | 5,00,000 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of 380mm sweep, 1400 rpm (approx) propeller type exhaust fan complete as per IS, IE rule & site requirement. | — | — | — | 92,200 | |
| — | 40.00 | — | — | ||
| Supply & fixing of 1200 mm sweep energy saving BLDC ceiling fan with copper winding & with remote, 300mm length of down rod (without shackle), input power not more than 28W, minimum 1.1mm aluminium blade material, double ball bearing, 2 canopy, to be operated in AC single phase supply. | — | — | — | 1,14,880 | |
| — | 40.00 | — | — | ||
| Supply and fixing of fan hooks (D Hook with double fasteners 10 mm for hanging ceiling fans) as per the direction of site Engineer | — | — | — | 11,560 | |
| — | 40.00 | — | — | ||
| Supply and fixing of 2/3/4/6 feet down rod as per the direction of site Engineer | — | — | — | 11,560 | |
| — | 10.00 | — | — | ||
| Supply, fixing and commissioning of 18 Inch 450MM air circulator 450 mm ultra high speed 3 blade pedestal fan | — | — | — | 39,090 | |
| — | 4.00 | — | — | ||
| Supply, fixing, connecting and commissioning of 250mm sweep fresh air exhaust BLDC fan complete. | — | — | — | 7,752 | |
| — | 10.00 | — | — | ||
| Supply, connecting and commissioning of ceiling mounted Occupancy (Presence) Sensor similar to Legrand make as per the direction of site Engineer | — | — | — | 38,990 | |
| — | 143.00 | — | — | ||
| Supply, fixing, connecting and commissioning of 20 Watts 1200mm LED tube aluminium light fitting (warm white/cool white) with lamp including wiring connections etc. as per enclosed specification as per the directions of Engineer at site | — | — | — | 80,509 | |
| — | 166.00 | — | — | ||
| Supply & fixing of 15W LED recess mounting down lighting round, greater than 180mm dia suitable to operate on 230v, 50Hz AC supply as per HQ specification and as per the directions of engineer at site. | — | — | — | 1,04,580 | |
| — | 40.00 | — | — | ||
| Supply, fixing, connecting and commissioning of 35W LED Panel light fitting 2'x2' square type (warm white/cool white) with other connected accessories etc. | — | — | — | 1,09,200 | |
| — | 4.00 | — | — | ||
| Supply, fixing, connecting and commissioning of automatic light controlling nature switch device, grade sensors and advanced micro-controllers with suitable power contactor and MCB, enclosed in a FRP enclosure for pole mounting, confirming to IS-54 and similar to swadeep-02 EC-03 kW 1phase. The device should have the following specifications: 1)Operating voltage range:120V, AC 50Hz 2)Switching endurance 5000 cycles of ON and OFF minimum 3)Operating illumination levels a)for switching On-less than 60Lux for 30 seconds b)for switching OFF greater than 10Lux for 30 seconds 4)Auto voltage levels a)High voltage trip/auto reset- if voltage and gt 280 AC/and it 270V resp. 5)LED for indicating the operating status 6)During based switching OFF option of 04 to 08 hours with resolution of 1/2 hour 7)Override option continuous ON and continuous OFF | — | — | — | 36,616 | |
| — | 13.00 | — | — | ||
| Supply, fixing, connecting and commissioning of Vertical SDB with IP 56 protection & comprising of 1 x 63A 4P RCCB with 100 mA, 1x63A MCCB TPN, 6 x 32A MCB DP and 2x20A MCB SP with double door, flush mounting Legrand make as per the directions of engineer at site. | — | — | — | 4,21,733 | |
| — | 20.00 | — | — | ||
| Supply & erection of 5m long hot dip galvanized octagonal pole with 130mm bottom A/F and 70mm top A/F, made up of 3mm thick HT Sheet & Bakelite sheet & suitable MCB including suitable size of loop-in & loop-out connectors (for mounting inside the base compartment of pole with hinged door opening arrangements), with base plate of size 200x200x12mm, M16X 600 long 'J' type EN8 grade foundation bolts, with 1000mm Single arm bracket for fixing of LED light with all connected accessories, etc. | — | — | — | 1,46,320 | |
| — | 8.00 | — | — | ||
| Supply & erection of 5m long hot dip galvanized octagonal pole with 130mm bottom A/F and 70mm top A/F, made up of 3mm thick HT Sheet & Bakelite sheet & suitable MCB including suitable size of loop-in & loop-out connectors (for mounting inside the base compartment of pole with hinged door opening arrangements), with base plate of size 200x200x12mm, M16X 600 long 'J' type EN8 grade foundation bolts, with 1000mm double arm bracket for fixing of LED light with all connected accessories, etc. | — | — | — | 77,256 | |
| — | 28.00 | — | — | ||
| Excavation of pit for octagonal pole/poles of suitable size in all type of soils as per the direction of engineer at site | — | — | — | 28,000 | |
| — | 20.00 | — | — | ||
| Provision of concrete foundation and constructing the plinth as per the directions of engineer at site. | — | — | — | 80,060 | |
| — | 99.00 | — | — | ||
| Supply & fixing of suitable cable termination lug & glands (1 set comprises 4 no lugs & 4 no glands) as per the site requirement | — | — | — | 9,900 | |
| — | 46.00 | — | — | ||
| Supply, fixing, connecting and commissioning of 60W LED street light complete with necessary clamps and hardware etc. as per Railway specification | — | — | — | 1,29,260 | |
| — | 3.00 | — | — | ||
| Supply, installation and commissioning of 1.5 Ton Split Air conditioner - with 5 BEE Star rating inverter, copper coil, ISEER: 4.6 or above with connected accessories etc. | — | — | — | 1,19,970 | |
| — | 3.00 | — | — | ||
| Supply and fixing of suitable size out door stand heavy duty for suitable 1.5 TR Split AC unit including all connected accessories etc. | — | — | — | 2,166 | |
| — | 120.00 | — | — | ||
| Supply and fixing of extra copper pipe for Split AC (if required as per site condition) | — | — | — | 51,000 | |
| — | 120.00 | — | — | ||
| Supply, installation of hard/soft copper refrigerant piping complete with insulation foaming with wrapping, fittings, elbows, bends, supporting arrangements on wall for 2/3TR Cassette Split AC (if required as per site condition) | — | — | — | 1,34,520 | |
| — | 120.00 | — | — | ||
| Supply and fixing of drain pipe CPVC of 25mm dia including accessories, bend, elbows, tees, flanges, tappings, wall sleeves, hangers supports anchors etc. | — | — | — | 23,160 | |
| — | 200.00 | — | — | ||
| Supply and fixing of 4 corex4Sq.mm flexible FRLS copper cable (communication cabling) for Split/Cassette AC | — | — | — | 73,000 | |
| — | 200.00 | — | — | ||
| Supply and fixing of 4 corex2.5Sq.mm flexible FRLS copper cable (communication cabling) for Split/Cassette AC | — | — | — | 41,600 | |
| — | 2.00 | — | — | ||
| Supply, installation, testing, gas charging & commissioning of 2TR capacity BEE star rated Inverter cassette AC unit, copper coil with all connected accessories. | — | — | — | 2,27,840 | |
| — | 40.00 | — | — | ||
| Supply, installation of hard/soft copper refrigerant piping complete with fittings, elbows, bends, supporting arrangements on wall for 2/3TR Cassette as per the direction of Engineer at site. | — | — | — | 44,840 | |
| — | 2.00 | — | — | ||
| Supply, fabrication and fixing of suitable size out door wall mounted chair type MS base frame stand for outdoor unit 2/ 3.0TR cassette unit including all connected accessories etc. | — | — | — | 4,720 | |
| — | 5.00 | — | — | ||
| Supply & fixing of 32A capacity MCB DP similar to GM make as per the directions of engineer at site (for ac units) | — | — | — | 2,200 | |
| — | 70.00 | — | — | ||
| Supply and fixing of 20A SP MCB 'C' curve 10KA | — | — | — | 9,730 | |
| — | 30.00 | — | — | ||
| Supply, fixing, connecting and commissioning of Master control 16A DP MCB as per the direction of the Engineer at site | — | — | — | 12,780 | |
| — | 10.00 | — | — | ||
| Supply, fixing, connecting and commissioning of Master control 32A DP MCB as per the direction of the Engineer at site | — | — | — | 6,800 | |
| — | 10.00 | — | — | ||
| Supply, fixing, connecting and commissioning of Master control 32A TPN MCB as per the direction of the Engineer at site | — | — | — | 13,750 | |
| — | 9.00 | — | — | ||
| Supply, fixing, connecting and commissioning of Master control 63A TPN MCB as per the direction of the Engineer at site | — | — | — | 18,036 | |
| — | 3.00 | — | — | ||
| Supply, erection, commissioning of 63A/100A 4 Pole ELCB 6 KA with 100mA sensitivity as per the direction of the engineer at site. | — | — | — | 11,232 | |
| — | 35.00 | — | — | ||
| Supply and fixing of 25 amp 30mA DP RCCB as per the direction of the engineer at site. | — | — | — | 69,300 | |
| — | 2.00 | — | — | ||
| Supply and fixing of 40 amp 4pole 32mA RCCB as per the direction of the engineer at site. | — | — | — | 5,580 | |
| — | 200.00 | — | — | ||
| Lowering of GI pipe/HDPE pipe submersible pumps in the existing bores/new bores of various capacities above 600 Ft depths including transportation of pumps from depot to site. The required tools, nipple, reducers, couplers, PVC & water proof tape rolls, trypod, man power including all connected accessories etc., and transportation shall be at the contractor's cost only as per the direction of site Engineer. | — | — | — | 10,000 | |
| — | 1.00 | — | — | ||
| Lowering of submersible pumps (HDPE Pipe) in the existing bores of various capacities upto 600 Ft depths including transportation of pumps from depot to site. The required tools, nipple, reducers, couplers, PVC & water proof tape rolls, trypod, man power, transportation shall be at the contractor's cost only including all connected accessories etc. as per the direction of site Engineer. | — | — | — | 3,646 | |
| — | 1.00 | — | — | ||
| Supply of stainless steels and/or mud proof submersible pump of 7.5HP vertical type energy efficient submersible pump with a total head of 300Mts with a discharge of 30LPM at total head suitable to work on 3-ph with pump maximum outer dia 98mm as per the directions of engineer at site | — | — | — | 57,222 | |
| — | 300.00 | — | — | ||
| Supply and laying of HDPE pipe with required fittings and joints of 40mm outer dia. Manufacturing of PE-100 grade material. The pipe pressure class of PN-16. The pipe should be suitable for drinking/raw water application as per direction of engineer at site. | — | — | — | 40,500 | |
| — | 200.00 | — | — | ||
| Supply, laying, connecting and commissioning of 3 core 4sq.mm copper flat cable as per the direction of site Engineer. | — | — | — | 33,600 | |
| — | 4.00 | — | — | ||
| Supply & fixing of 4 Nos. of 2"x1.5', 6" GI bore cover, 2" GI bend, GI coupler, 2"x3' GI for coupling, suitable capacity nut & bolt the GI/HDPE pipe and pump & connected accessories as per the directions of engineer at site | — | — | — | 9,872 | |
| — | 2.00 | — | — | ||
| Supply & fixing of control panel consisting of DOL starter, single phase preventer with power automatic ON & OFF system, with dry run, pilot lamps, selector switch, Voltmeter, Ammeter in suitable sheet steel box of 16SWG upto 7.5HP pumps including all connected accessories as per the directions of engineer at site. | — | — | — | 28,274 | |
| — | 4.00 | — | — | ||
| Design, fabrication, fixing, connecting and commissioning of outdoor type cable termination box of 2'x2'x1' size with 2mm thick sheet duly providing of clamps to fix with pole and have proper locking arrangements as per the site requirement. This item also includes termination of existing cable to the termination box with copper bus bar of size 75x5mm & 63A 4P MCB as per the directions of the engineer at site. | — | — | — | 23,920 | |
| — | 2.00 | — | — | ||
| Supply & laying/spreading of 20 mm ballast (hard granite metal) to electrical sub stations in SC area including transportation, loading and un loading of ballast at location as directed by the Engineer at site | — | — | — | 2,700 | |
| — | 50.00 | — | — | ||
| Supply & erection of Cast Iron LT Cable Marker as per the directions of Engineer at site | — | — | — | 13,750 | |
| — | 10.00 | — | — | ||
| Supply of ELECTROSAFE Insulating Mats 3000mm x 1000mm x 3mm thick class 'B' as per IS 15652 latest along with test certificates, ISI marking on mat for electrical purpose | — | — | — | 18,000 | |
| — | 200.00 | — | — | ||
| Supply, installation and commissioning of LED colour rope light multi colour (warm white, white, green, saffron, pink, blue) as per the direction of site Engineer suitable to operate on 220V to 250V single phase AC supply as per directions of engineer at site | — | — | — | 29,800 | |
| — | 20.00 | — | — | ||
| Supply, installation and commissioning of connectors for rope light as per directions of engineer at site | — | — | — | 5,400 | |
| — | 2.00 | — | — | ||
| Supply, fixing, commissioning and testing of Solar Water Heater of 500 LPD ETC model including the plumbing inlet and outlet, cement pedestal (9" x 9") and all other connected accessories as per the instructions of engineer at site. | — | — | — | 1,77,000 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
NEFTForm.pdf
ATTACHMENT
ExperianceCertificate.pdf
ATTACHMENT
New GCC April 2022
ATTACHMENT
I_CT_GCC-
ATTACHMENT
3toGCCApril.2022RBCE_CE-I-
ATTACHMENT
GCC-2022-
ATTACHMENT
Tender Document
ATTACHMENT
GCC_April-2022_2022_New.pdf
ATTACHMENT
CorrectionSlip2022_CE-I_CT_GCC-2022Policy14.07.2022_1.pdf
ATTACHMENT
ACS-3toGCCApril.2022RBCE_CE-I-CT2023_04_26.pdf
ATTACHMENT
ACS-2toGCC-2022-CE-1-CT-GCC-2022-POLICY_13.12.2022.pdf
ATTACHMENT
ApprovedTB37-HRD-25-26STTC.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .