SPECIAL REPAIR TO BLDG NO. P-2 AT SITE-II AT FATEHGARH CANTT

Amount

S&F in repair Cast iron soil, waste and vent pipe of bore 100mm sand cast in any length with or without ears with provn of run lead joints fixed to wall complete all as specified and directed

S&F in repair Cast iron soil, waste and vent pipe of bore 100mm sand cast in any length with or without ears with provn of run lead joints laid in trenches or in floors complete all as Specified and directed

S&F Cast iron bends (any redius) 100mm bore with oval access door fixed with provn of run lead joints complete all as specified and directed.

S&F in repair Cast iron 'P' or S trap trap with 100 mm dia out let with stainless steel grating including jointing to waste pipe with provn of run lead joint complete all as specified and directed.

S&F in repair CI branch pieces double (equal or unequal) ordinary or inverted fitted (spigot and socket type) with oval access door of size 100mm complete all as specified and directed.

S&F in repair CI sockets double coller suitable for 100 mm bore of pipe complete all as specified and directed.

S&F in repair Cast iron cowls 100 mm complete all as specified and directed.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm dia of pipe complete all as specified and directed.

S&F in repair Salt-glazed stoneware gully traps type S, square or round mouthed size 150 x 150 mm complete all as specified and directed.

Dismantling water tanks exc 250 &n exc 500 litres complete all as specified and directed

S & F three layered rotational moulded polyethylene water storage tanks 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight -210 gms) complete all as specified and directed

S&F in repair Vitreous China Wash Basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets , 32 mm PVC waste pipe and including 32 mm PTMT Waste coupling and 15 mm dia Pillar taps fancy type chromium plated complete all as specified and directed

S&F in repair Vitreous China Wash down water closet semi-pedestal patteren (anglo indian type) white with plastic seat cover including connection to trap / drain and to flushing pipe, anti-syphonage type and making good to floor complete all as specified and as directed

S&F in repair PVC Low Level Flushing cistern PVC valveless syphonic action type, 10 ltrs capacity white, with inlet, ball float valve and handle including brackets and connections to pipes complete all as specified and directed.

Taking up or down Steel Tubing bore of pipe in 15mm and connections etc complete all as specified and directed.

All as per item No.15 above but of 20 mm bore complete all as specified and directed.

S&F Steel Tubes Medium Grade and Bore of tube in 15mm galavanised with all fitting laid in walls, ceiling or laid in floors etc complete all as specified and directed.

All as per item No.17 above but of size of 20mm bore complete all as specified and directed.

M&L for cutting chases, pinning in brick walls making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F in repair 15mm bore Chromium plated Bib taps fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 15 mm bore ,Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated with long screwed shank and cup (concealed type) complete all as specified and directed.

S&F in repair 15 mm bore ,Stop valves/angle valve, cast copper alloy,screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed fancy type, chromium plated complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm etc complete all as specified and directed.

S & F in repairs brass chromium plated showe rose 125mm size with shower arm complete all as specified an directed.

S & F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair stainless steel utencil plate rack 1 mm thick of size 60 cm x 60 cm, of pattern as approved by engineer-in-charge, fixed to wall by means of four nos rawl plugs, complete all as specified and directed.

S&F in repair PTMT grating doom 100mm dia with or without waste hole etc complete all as specified and directed.

S & F in repair tubular towel rail 20mm dia 60 cm long between flange, brass chromium plated including bracket complete all as specified and directed.

S & F in repair Gun-metal, globe or gate valves 20 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed

S & F in repair Gun-metal, globe or gate valves 15 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm each not exc 4.00 sqm each. Complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm complete all as specified and directed.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or welded duly one coat of shop coat of primer complete all as specified and directed.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars,dovetailed or welded duly one coat of shop coat of primer complete all as specified and directed.

S&F factory made steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed

S&F in repair Built in steel Cupboard (shutter and frame) of pressed steel frame of size 75mm x45mm x1.25 mm thick with pressed steel shutter 1.00mm thick Godrej Pattern fixed to masonary walls by hold fast made out of 25 x 3 mm FI embeded in PCC 1 :2 : 4 type B1 complete, incl two coats of spray painting over a coat of red oxide primer on steel surfaces,including hinges,handle/lock godrej pattern, complete all as directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm palin colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S Frame shall be covered with heat moulded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock and bottom rail on either side & as gap insert for tip rail & bottorm rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/seated to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site as per specification & drawing.

S&F Pressed steel frames 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F Pressed steel frames 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified and directed.

S&F factory made 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made 35 mm thick 2nd class hardwood as in Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section of 125mm size etc complete all as specified and directed.

S&F Aluminium handles, cast type anodised of size 125mm etc complete all as specified and directed.

S & F mild steel sliding door bolt 300mm long clip type, stove enamelled black with bright bolt not less than 16mm dia complete all as specified and directed

S & F mild steel barrel tower bolt 200mm long, stove enameled black with bright bolts complete all as specified and directed.

S & F mild steel pressed handle oval type stove enameled black of size 150mm complete all as specified and directed.

S&F mild steel butt hinges cold rolled of size 100mm medium weight complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples, wodden beads to steel windows/wodden doors complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks complete all as specified and directed.

S&F 150 mm long ordinary helical door spring including rollar & rollar plate fixed to doors with screws complete all as specified & directed.

M&L Cement concrete type C1, 1:3:6 (20 mm graded stone aggreagte) as in filling inside pressed steel chowkhats complete all as specified and directed.

Dismantling timber scantling as in battens, rails, posts, etc. under 40 sq. cm in section complete all as specified and directed

M&L for MS work as in Framed work as in chowkhats of doors or gates of angle or other section with gusset plates, rails, braces, etc.,conforming to Fe.290.Gde-E-165 complete all as specified and directed

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framed work and similar works conforming to Fe-290 Gd E-165 complete all as specified and directed.

S&F for framed work for portions framed and hung as gates including hinges, stops, hand made sliding bolts etc conforming to Fe-290. Gde -E-165 complete all as specified and directed.

S&F in repair expanded metal of weight less then 4.00 kg/Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed.

S&F in repair MS work 0.63 mm Mild steel, plain, black sheet as in steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and directed.

M&L for MS work as in Framed work as in doors or gates of angle or other sectionwith gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 410-W(Gde E- 250) quality A complete all as specified and directed

S&F for Purpose made butt hinges,sliding bolt,handle conforming to Fe-290 Gde-E-165 suitable for fixing to stone / concrete door and window frames all as specified and directed

M&L Preparing of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

All as per item No.64 above but over a coat of red oxide primer complete all as specified and as directed.

M&L preparing new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer on roofs complete all as specified and directed.

Demolition mud in roofs any thickness including and leeping (whether full thickness removed or only a part thereof) including tarfelt etc and removing debris by any means outside of defence land complete all as specified and directed.

M & L water proofing treatment on existing roof with the following speification complete all as specified and directed. (a) preparation of concrete surface and M&L 10 mm thick (average) plaster on roof in CM (1:4) with and including liquid water proofing compound as per manufacturer instruction (b) Apply bituminous primer @ 0.5 Ltr/Sqm confirming to IS 3384-1965 on prepared surface till the surface is properly pregnated (c) Laying APP based polymeric water proofing membrane minimum weight not less than 3.0 Kg/Sqm and minimum 3 mm thick reinforced with polyster non wove fabric (Wt not less than 3 Kg / sqm) laid on primed surface by torched sealed application with overlap complete with as per manufacturer instructions confirming to IS. (d) Applying hot air blown bitumen 85/25 @ 1.2 Kg / Sqm and spreading of clean washed sand @ 1 Kg / Sqm to make a bond between polythene surface and screed bed. Note :- Water proofing treatment shall be carried out by authorized applicator of approved company.

M & L for 40 mm thick brick tiles laid over 15 mm thick bedding layer of CM (1:6) and joints grouted flush in CM (1:3) mixed with crude oil @ 5% by weight of cement complete all as specified and directed.

All as per item No.70 above but except tiles complete all as specified and directed.

Supply only liquid Water proofing Compound ISI marked complete all as specified and directed.

M&L for Providing, cement concrete type B-1, 1:2:4 (using 20 mm grded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Taking down cement plaster on brick wall or stone wall etc. including raking out joints hacking for key, scrubbing down with water etc and disposed off unserviceable material of out side MD land complete all as specified and directed.

Demolition of brickwork masonary built in lime or cement mortar including all quiens arches, pillars etc. But including concrete articles complete all as specified and directed.

M & L Brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in cm (1:6) complete all as specified and directed.

All as per item No. 76 above but except Bricks etc complete all as specified and directed.

M&L half brick thick walls built in CM 1:4 Sub Class B old size bricks straight or curved on plan to any radius complete all as specified and directed.

M & L Rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M & L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3) on fair faces of brick work ceilling concrete surfaces to be finished even and fair without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of white cement primer complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of white cement primer complete all as specified and as directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceilling complete all as specified and directed.

M & L for preparation of old plastered surfaces of walls by rubbing down and making surface smooth and applying two coats of oil bound distemper complete all as specified and directed.

M & L for preparation of old plastered surfaces of walls by rubbing down and making surface smooth and applying two coats of cement base paint complete all as specified and directed.

M & L for preparation of old plastered surfaces of ceiling by rubbing down and making surface smooth and applying two coats of white wash complete all as specified and directed.

M&L prepartion of old wood & wood based surfces of any decsription not other wise described over 10cm width or girth and apply one coat of synthetic enamel paint complete all as specified and directed

M&L prepartion of old painted steel surfces of any decsription not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismanting of existing sunken treatment including plaster and M&L for water proofing treatment on existing sunken floor/wall with the following specification complete all as specified and directed- (a) 15mm thick (average) plaster in CM 1:3 on sunken floors and walls using liquid water proofing compound in as per manufacturer instruction (b) Apply one coat bituminous primer @ 0.5 Kg/ Sqm on walls and floor conforming to IS 3384-1965 on prepared surface till the surface is properly impregnated (c) Apply hot bitumen 85/25 grade @ 1.2 Kgs/Sqm confirming to IS 702-1988 (d) Laying APP polymeric water proofing memberance weight not less than 3.0 Kgs/Sqm as per manufacturer instructions confirming to IS (e) One spout of 40mm GI pipe length 0.45 M shall be provided in sunken floor (f) Filling of sunken floor with PCC 1:5:10 type D-2 upto height directed (g) fixing of PVC trap as per site requirement

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of PCC in Ground floors/PCC Path/Plinth Protection and paving n.exc 15cm thickness (below or above ground level) etc complete all as specified and directed.

M & L 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded aggregateds as in sub base of tiles complete all as specified and directed.

M & L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors,skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer of cement (1:6) complete all as specified and directed.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mmthick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick bedding in CM 1:4 complete all as specified and directed.

M & L for machine cut kota stone slab as a single piece in stair case trades flooring 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for machine cut kota stone slab as a single piece in stair case riser and skrting/dado 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10mm thick rendering 1:4 complete all as specified and directed.

M&L for 18-20 mm th Granite (of any type) work (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15 mm thick screed in CM 1:6 complete all as specified and directed.

M & L for providing prepolished chequered cement concrete tiles of size 20cm x 20cm x 25mm thick set & jointed in neat cement slurry with grey cement and pigment including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of chequered tile complete all as specified and directed.

M&L for 75 mm thick PCC (Cement concrete) 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection finished even and fair and making 50mm deep joints at every 3 metre interval and at every corner and filling the joints with bitumen of grade 85/25 and sand mixture 1:3 complete all as specified and directed.

S&F 150mm dia GI pipe medium grade as in spouts fixed to parapet walls on roof terrace,incl setting and fixing in cement concrete 1:2:4 and making necessary repairs etc incl removing old pipe complete all as specified and directed.

Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and including taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed.

Taking down aluminium sub main wiring and making good disturbed surfaces to match with the existing surface roof / wall / floor complete all as specified and directed.

Material and labour for point wiring for one light point or one fan or bell point controlled by one switch with using 1.5 Sqmm (nominal area) stranded copper conductor, single core, PVC (FRLS) insulated & unsheathed cable, 1100 volts grade in and including concealed PVC conduit (Medium grade) of suitable size all as directed with using new sunken type pressed steel box / terminal boxes for mounting fittings/junction boxes not less than 1.6mm thick duly painted with two coats of black bituminous paint over a coat of red oxide primer with 3mm thick bakelite laminated sheet, and including all accessories and using 1.5 Sqmm (nominal area) stranded copper conductor single core conductor, PVC insulated & unsheathed cable as in earth wire connected to common earth dolly complete for one light point 5/6 Amp complete all as specified and directed.

All as per Srl item No 104 here in above but point wiring for 5 pin switch socket combination point, 5/6 Amps on independent board controlled by one switch.complete all as specified and directed.

All as per Srl item No 104 here in above but point wiring for 5 pin switch socket outlet, 5 Amps on same board with other switches complete all as specified and directed.

All as per item No.104 here in above but one light point controlled by 02 Nos two way switches complete all as specified and directed.

All as per item No.104 here in above but one bell point controlled by one bell push switche complete all as specified and directed.

All as per Srl item No 104 here in above but point wiring for one six pin switch socket indepdent, 15 & 5 Amps (independent) controlled by one switch with using 2.5 Sqmm (nominal area) stranded copper conductor in wiring and earth complete all as specified and directed. Notes for item 104 to item 109 here in before : (i) The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc. for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at RCC Columns/Beams/Ceilings shall be in surface conduit of suitable size fixed on surface with using PVC rawl plugs and provision of covering sunken boards/terminal boxes / junction boxes of any shape and size with 3mm thick bakelitelaminated sheet fixed with suitable GI screws and cup washers) (ii) Fittings like switches, sockets, regulators, lamp holders, light fittings shall be measured and paid for separately under appropriate item of Schedule `A' (iii) The size of conduits shall be determined on permissible No. of runs of wires as specified in SSR Part-I (2009) clause 19.125 (B). However minimum size of conduit shall be 20mm dia (Medium grade)

Supplying & fixing for piano switch flush type, 5/6 Amps, single pole, one way , 230 volts AC circuit complete all as specified & directed.

Fixing only for piano switch flush type, 5/6 Amps, single pole, one way , 230 volts AC circuit complete all as specified & directed. Note :- Retrieved piano switch from item No.102 shall be reused

Supplying & fixing for switch socket combination 2 in 1, 5 pin and 5 Amp flush type complete all as specified and directed.

Fixing only for switch socket combination 5 in 1, 5 pin and 15 Amp flush type complete all as specified and directed. Note :- Retrieved switch from item No.102 shall be reused

Supplying & fixing switch piano two way 5 Amp single pole complete all as specified and directed at site.

Supplying & fixing bell push, 230 volts AC circuit complete all as specified & directed.

Supplying & fixing bell (Ding dong), 230 volts AC circuit complete all as specified & directed.

Supplying & fixing for lamp holder PVC / Polycarbonate type, insulated body with back plate suitable for batten fitting complete all as specified & directed.

Supply and fixing rotory 5 stepped type electronic fan regulator 100 watt 230 volts complete all as specified & directed.

Fixing only rotory 5 stepped type electronic fan regulator 100 watt 230 volts complete all as specified & directed. Note :- Retrieved regulator from item No.102 shall be reused

S&F ceiling rose PVC / polycarbonate isolated body three terminal AC 230 volts complete all as specified and directed.

M&L for sub main wiring using two single core PVC insulated, unsheathed stranded copper conductor cable of size 6 Sqmm of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of dia not less than 20mm with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 4 Sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed. Notes :- (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc. for concealing the conduits to required depth & making good the disturbed surface in cement sand mortar 1:4 including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling/RCC surfaces shall be in surface conduit of suitable size fixed on ceiling/RCC surfaces with using PVC rawl plugs)

Supply and fixing in repair of VTPN DB suitable for mounting MCCB as incomer of rating 63 Amp vertical distribution board 4 way with suitable rated bus bar having IP-43 protection and double metal door concealed in wall complete electrical connection with aluminum thimbles as required complete all as specified and directed. Make- C&S Cat part No.CSDBTPNVDD04S, Legrand Cat part No. 507730 & Indo Asian Cat part No.811870

Supply and fixing in repair MCB distribution board SPN 240 volt, 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with copper thimbles as required complete all as specified and directed. Cat part No.5076 11 of make Legrand or equivalent model as specified make as approved by GE.

Supply and fixing in repair magnetic release of MCCB 63 Amp, 16KA, 4 pole including complete electrical connection by appropriate size of copper lugs complete all as specified and directed. Make - Legrand Cat part No.027029, ABB Cat part No.1SDA068770R1 & Indo Asian Cat part No.830036.

Supply and fixing in repair of MCB SPN 16-40 Amp 240 volt 'C' 10 KA curve complete all as specified and directed.

Supply and fixing MCB of MCB SP 6 to 32 Amp 240 volts 'C' curve 10 KA complete all as specified and directed.

S&F in repair LED 20 watt LED extruded aluminium battan fitting batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption < 20W (4 FT 20 W), luminaire lumen >2000 lm, system efficiency of > 120 lumens / W, with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 45 ºC, driver efficency >85%, power factor >0.9, THD <20% as per IEC 61000-3-2, colour temp - 6500K, surge protection 2.5 KV, 50000 burning hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level <60V DC as per IEC standard with LM70 & LM80 certification complete all as specified and directed. Philips Cat Part No.BN02IC LED20S PSU CW GR 52, Wipro Cat Part No.LL20-281-XXX-65AL1 & Bajaj Cat part No.BJCEB 118/120 W2EB 1X18/20W FTL.

S&F in repair LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption < 10W (2 feet 10 W) luminaire lumen > 1000 lm, system efficiency of > 120 lumens / W, with LED binning as per ANSI Bin C78.377A, photo biological safety report as per IEC624718 & electrical insulation class I, Ingress protection IP 20, colour rendering index CRI>80, temp range 0 to 45 ºC, driver efficency >85%, power factor > 0.9, THD <20% as per IEC 61000-3-2, colour temp - 6500K, surge protection 2.5 KV, 50000 buring hrs (min) as per L70 criteria, two stages isolated constant current operated driver with range 150-270V AC and safety extra lower voltage safe level <60 V DC as per IEC standard with LM70 & LM80 certification complete all as specified and directed. Make- Philips Cat No.BN021 LED 10S-6500 PSU GR S1, Wipro Cat No.LL20-111-XXX-65NE3 & C&S Cat part No.LTTB2F10WLED/W

Supply and fixing in repair with metal plug & socket DB with metal plug and MCBs double pole and neutral enclosure with a two pin earth plug and socket suitable for 32 Amp complete with one single pole MCB complete all as specified and directed.

M&L in repair for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

S S TRADING CO

M/S BABA BUILDERS

Shree Gopal Engineers & Contractor

M/S SRI JAGDAMBE TRADERS

M/S S P CONSTRUCTION