SPECIAL REPAIR TO BUILDING NO P-26/2 AT 119 MC/MF DET UNDER GE GUWAHATI

Amount

Demolition of cement concrete (un reinforced) of any description and in any position complete all as directed.

Demolition of cement concrete (reinforced) in roofs, floors, beams chajja etc (other than ground floors) complete all as directed.

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillers etc but excluding ashlar facigs, dressed stonework and precast concrete articles complete all as directed.

Taking down old damaged cement plaster of any description including racking out joints hacking for key, scrubbing down with water complete all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons, cooking platforms etc laid, beddd and pointed in any mortar complete all as directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) n.exc 1.5 Sqm each complete all as directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frame) exc 1.5 Sqm but n.exc 4 Sqm each complete as directed.

Dismantling of steel sheeting plain or corrugated of any gauge or thickness as in roof covering complete all as directed.

Dismantling wrought iron or mild steel work of any description and any position complete all as directed.

Dismantling of Wall and ceiling boards (fibre,pulp, insulation, etc.) of any thickness, including cover fillets complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Materials and Labour for PCC (1:3:6) type C-2 (using 40 mm graded agreegate) as in foudation, mass concrete for post and as similar work etc. complete all as specified and as directed.

Materials and Labour for brick work with sub-class 'B' bricks, straight or curved on plan to any radius in full brick thick walls, built in cement mortar 1:4 complete as specified and directed.

Materials and Labour for rendering 15 mm thick in two layers (10mm + 5mm) externally in cement mortar (1:4) on fair faces of brick work or concrete surfaces mixed with water proofing compound @200ml/50kg of cement on top layer of 5mm thick as per manufacturer’s instructions and finishing the surfaces fair and even without using extra cement complete (Note : WPC shall be measured and paid separately as ‘Supply only’)

Supply only liquid water proofing compound conforming to IS-2645 complete all as specified.

Materials and Labour for rendering 10mm thick on other than fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete as specified and directed.

Materials and Labour for preparation of new plastered surfaces of walls and applying two coats of distemper oil-emulsion over wall care putty complete as specified and directed.

Materials and Labour for preparation of new plastered/unplastered surfaces of walls and applying two coats of weather exterior acrylic emulson wall paint, over thick layer of wall putty, complete all as specified and directed

Materials and Labour for complete removal of existing treatment of old plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of chalk whiting for preparation of distempering incl putty finishing all as specified and directed.

Materials and Labour for preparing old faded decorated surfaces of wall etc of any description and applying one coat of weather proof paint (exterior quality acrylic emulsion paint ) premium quality over a coat of acylic primer complete as per manufactuerers instructions and as specified and directed

Materials and Labour for rendering 10 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement.

Materials and Labour for preparing newly plastered suface of ceiling and applying three coats of white wash complete .

Materials and Labour for non-skid, ceramic, coloured tiles (first quality) 7 to 8mm thick (Square/ rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles including 15mm thick, screed bed or bedding layer, in cement mortar (1:4) for laying floor tiles, etc complete

Materials and Labour for glazed, ceramic, coloured tiles (first quality) of size 350x450x6-7mm thick as in vertical surfaces, such as skirting, dado, etc, set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles including 10 mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces even and rough as in backing coat complete all as specified and directed

Materials and Labour for vitrified tiles 10 mm thick light shade (square/rectangle) area at each tiles not exe 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete, all as specified and as directed.

Materials and Labour for vitrified, ceramic, coloured tiles of size 600x600x 10 mm thick ( Square / rectangular) light shade, in dado/ skirting etc set and jointed in neat cement slurry and pointed in white/coloured cement to match including rendering 10mm thick in cement mortar 1:4 , complete all as specified and as directed.

Materials and Labour for granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Materials and Labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

Materials and Labour for prepolished, coloured, cement concrete tiles 23 to 25 mm thick jointed and pointed, using with white cement and pigment in floors, etc including brushing with net cement slurry @ 3Kg/Sqm and 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Materials and Labour for in repair 0.50 mm thick pre painted galvalume aluminium zink coating GI based corrugated/semi corrugated steel sheet of any colour as approved of 550Mpa tensil strengtrh as in roof covering /cladding to wall, fixed with self taping screws complete.

Materials and Labour for in repair 0.50 mm thick pre painted galvalume aluminium zink coating GI based plain steel sheet of any colour as as approved of 550Mpa tensil strengtrh as in ridge, valley gutter, eves board etc fixed with self self taping screws complete.

Materials and Labour for preparation of old iron and steel surfaces of any description, exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete as specified and directed.

Materials and Labour for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring , path or like all as directed by Engineer-in-Charge.

Materials and Labour for 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 3 mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

Materials and Labour for 2nd class hard wood plain solid, straight chowkats and frames , wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

Supply and Fix Flush shutters, 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and Fix frame less toughended glass with moulded edges of size 1100mmx 2050mmx10mm push pull type door shutter having top and bottom patch with floor spring including necessary screws, handle and locking arrangement etc. complete as specified and directed.

Supply and Fix Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

Supply only 4mm thick Sheet glass frosted one side , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

Supply and Fix 35 mm thick 2nd class HW Glazed and skeletonshutters, open rebated and preparedto receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); complete all as specified and directed.

Supply and Fix stain less steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Supply and Fix in repair Continuous (piano) hinges of 30mm flange, mild steel, bright finish or electro galvanised complete all as specified and directed.

Supply and Fix solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet/single piece extruded PVC profiles reinforced with MS square tube fixed in opening as per specification & drawing complete as specified and directed.

Supply and Fix factory made solid panel PVC door shutter 30 mm thick(Style) consisting of frame made out of MS tube for top and bottom rails.MS frame shall be covered with heat moulded plain colour PVC ,C, channel having a PVC sheet strip of 20 mm width stuck inside with solvent for stiles complete and fixed to door frame complete all as specified and directed.

Supply and Fix 125mm long, Aluminium anodised barrel tower bolts, of extruded section complete.

Supply and Fix 100mm long, Aluminium anodised barrel tower bolts, of extruded section complete.

Supply and Fix 250mm long, Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

Supply and Fix 100mm size Butt hinges, medium weight, cold rollded mild steel complete all as specified and directed.

Supply and Fix 150mmextruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply and Fix 15mm bore, GI tubing, medium grade with all fittings for fixed to walls, ceilings or laid in floors including taking down old unsv tubing etc complete all as specified and directed.

Supply and Fix 20mm bore, GI tubing, medium grade with all fittings for fixed to walls, ceilings or laid in floors including taking down old unsv tubing etc complete all as specified and directed.

Materials and Labour for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of pink primer complete all as specified and directed.

Supply and Fix in repair white Vitreous china wash down water closet pan (pedestal pattern) including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts, including PVC valve less syphonic action type flushing cistern 10 ltr low level, white with inlet ball valve float and handle including bracket, one Nos PVC connection 15 mm dia & 600mm long with two Nos check nut and washer etc complete all as specified and directed .

Supply and Fix in repairs, Vitreous China wash basin, coloured of size 560mmx430mm with pedestal (excluding taps, ) but including chain and plug, porcelain stopper and brackets waste coupling, waste pipe complete all as specified and directed.(Make : Jaquar, Cat No C-0491 & C-0377 or equivalent make & model as approved)

Supply and Fix in repair basin mixer chromium plated, screwed for iron pipe complete all as specified and directed. (Make : Jaquar, Cat No VGP-81011B or equivalent make and model as approved).

Supply and Fix in repairs 15 mm bore brass chromium plated wall mixer for mixing the hot and cold water complete all as specified and directed. (Make : Jaquar, Cat No VGP-81079K & ALD-079 or equivalent make and model as approved)

Supply and Fix in repairs, Overhead shower multiflow 150mm x 150mm square without shower arm complete all as specified and directed.(Make : Jaquar, Cat No OHS 35495 or equivalent make and model as approved)

Supply and Fix in repairs, Shower arm casted heavy round with wall flange complete all as specified and directed. (Make : Jaquar, Cat No SHA-49483 or equivalent make and model as approved)

Supply and Fix in repairs, Hand Shower (Health Faucet) with 8mm dia, 1.2M m long flexible tube & wall hook complete all as specified and directed. (Make : Jaquar, Cat No-ALD- 573 or equivalent make and model as approved)

Supply and Fix in repairs, 15mm bore 2-way bib cock with wall flange complete all as specified and directed. (Make : Jaquar, Cat No FLR 5041 or equivalent make and model as approved)

Supply and Fix in repairs, 15mm bore angular stop cock with wall flange complete all as specified and directed. (Make : Jaquar, Cat No VGP-81053 or equivalent make and model as approved)

Supply and Fix in repairs, 100mm dia Hand shower multiflow (ABS chrome plated) with 1.5 m flexible tube with 12mm dia & swinging wall hook complete all as specified and directed. (Make : Jaquar, Cat No 1939, 559 & 555 or equivalent make and model as approved)

Supply and fix in repair Brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified. (Make : Jaquar, Cat No 1111 N or equivalent make and model as approved).

Supply and Fix in repairs, Soap dish chromium plated complete all as specified. (Make: Jaquar, Cat No AQN-7731 or equivalent make and model as approved).

Supply and Fix Corner Glass shelf (with bracket), chromium plated, fixed with and including Chromium plated brass screws on wooden/plastic cleats complete all as specified and directed. (Make : Jaquar, Cat No 1173 or equivalent make and model as approved).

Supply and Fix in repairs, PVC connection 15mm bore 450mm to 600mm long with hexagonal brass chromium plated nuts and washers on both sides complete all as specified and directed.

Supply and Fix in repair 32 mm bore low density polyethylene (LDPE) pipes of pressure rating 6 Kgf/Sq.cm as in waste pipe complete all as specified and directed.

Supply and Fix in repair bib tap 15 mm dia chromium plated, cast copper alloy with crutch or butter fly handle screwd fancy type for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply and Fix in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and Fix in repair PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and Fix in repair PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply and Fix PVC (SWR) bend any radius 110mm bore complete all as specified and directed.

Supply and Fix 110mm bore PVC (SWR) junction, single (Single T) equal or unequal complete all as specified and directed.

Supply and Fix110mm bore PVC (SWR) vent cowl complete all as specified and directed.

Materials and Labour for PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete 1:2:4 type B1 etc complete all as specified and directed.

Supply and Fix in repairs, decorative type mild steel PVC coated curtain rod including decorative type knob complete all as specified and directed.

Supply and Fix as in repair Toilet paper holder, chromium plated, box type fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

Materials and providing reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) in pre-cast slabs or like including necessary forwork etc complete all as specified and directed.

Materials and Labour for MS bars 6 to 8mm dia (TMT Bars) cut to length bent to shape reqd including cranking binding spirally for hooping cols, hooking ends and binding with and including mild steel wire annealled not less than 0.90 mm dia or securing with clips complete all as specified and directed.

Materials and Labour for false ceiling with 10 mm thick 600mm x900mm plaster of Paris sheets fixed with machine screws on and including GI channel 18 gauge thick grid work, main joists placed at 750 mm centre to centre , cross joists placed at 450mm centre to centre, hanging with 6mm dia GI wire suspenders from roof, ‘J’ hooks bolts and nuts etc and treating the POP sheets with thin layer of POP with Gypsum anhydrous binder and prepare the surface till smooth surface is achieved; and applying two coats of plastic emulsion paint over a coat of primer matching with the colour of ceiling sheets all complete as required as per manufacturer’s instructions and as directed .

Decorative Cornices/moulding using POP of cross sectional dimension exc. 13 Sqcm & n. exc 25 Sqcm as per pattern & design as approved & fixed in position including preparation of surfaces & applying two coats of plastic emulsion paint over a coat of primer matching with the colour of ceiling sheets all complete as required as per manufactuires instrucions & as directed

S&F in repairs, Stainless steel sink with drainage board, made out of 1.00mm thick stainless steel for kitchen or laboratory with plug, CP waste coupling, waste pipe, washers including cantilever cast iron brackets, connecting union, etc complete overall size 915mm x 460mm, bowl size 410mm x 330 mm x 160mm complete all as specified and directed.

Materials and Labour for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate in leveling course as in roof padding , complete all as specified and directed.

Materials and Labour for Water proofing treatment on RCC roof etc. comprising with the following operations and as specified herein below :- (a) Taking down/scrapping out existing old tarfelt bituminous compound including, sweeping, cleaning, washing down to remove dust etc and removing debris to a distance n.exc. 250m. (b) 15 mm thick plastering in cement mortar 1:4 finished even & smooth and curing for minimum 7 days. (c) Preparing & cleaning of fully dried cement plastered surface (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.4 litres per Sqm conforming IS-3384 - 1986 (e) A layer of APP based polymeric membrane 3mm thick (minimum), weighing 3.5 kg per Sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/sqm )shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm on longitudinal direction. (f) One coat of aluminium paint over the APP based membrane @ 0.11 Kg/Sqm complete all as specified and directed.

Materials and Labour for Cutting out to V- section in existing roofs or terracing , cleaning out ,wetting, grouting with cement mortar (1:3), complete all as specified and directed

Supply and Fix Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms)

Dismantling of old unserviceable water tank, removing from site, Supply and fixing of rotational moulded polythene water storage tank 1000 litre capacity ISI marked (cylindrical, vertical, double layered with closed top) hoisted and fixed in position Complete all as specified and directed.

Materials and Labour for providing and injecting chemical emulsion for post constructional anti - termite treatment along with external wall below concrete or masonry apron using chemical emulsion @ 2.25 liters per linear metre including drilling and plugging holes and finished upto derived level in apron complete all as specified and directed.

Materials and Labour for providing post construction anti-termite treatment by making hole of 12 mm dia to be drilled at 300 mm apart at the junction of external and internal wall with floor and construction / expansion joint if any, ground floor, only and pouring the emulsion at the rate of 01 Ltr per hole and plugging the same with white / coloured cement to match the existing surface etc complete all as specified and directed.

Materials and Labour for providing post A.T.T treatment at points of contact of wood work such as chowkats of wooden doors, window, ventilators, loft, ward robes etc by chemical emulsion (in oil or kerosene based solution) @ 0.5 Ltr / hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same etc complete all as specified and as directed.

Supply and Fix for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1998 grade St-240 complete all as specified.

Supply and Fix RCC Jalli preast 30mm thick (measured solid) 1:2:4, Type BO (12.5mm graded stone aggregate) set in CM 1:4 all as specified and directed.

Supply and Fix in repair 18/19mm block board, grade 2nd quality, interior grade decorative type with decorative face veneer on one face fixed with screw to timber frame work complete all as specified.

Taking down carefully aluminum/copper point wiring (light, fan ,bell,socket or power) complete including fittings & fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good disturbed surfaces of walls, floors etc complete all as required as directed.

Taking down main switche/DB of any type including wooden board/junction box and MCB etc complete all as specified and directed.

Taking down carefully old unserviceable copper/aluminium sub main wiring/service cable of any size including conduit/casing and making good disturbed surface complete all as specified and directed.

Materials and Labour for Point wiring with 1.5 sq mm (nominal area) single core PVC insulated FRLS unsheathed multi-stranded copper conductor cable (maintaining colour code), 1100 volts grade in and including PVC conduits of suitable size but not less than 20 mm dia (medium grade) with all fittings and accessories concealed in walls/ceiling etc including cutting chases for conduits and including modular metal flush box for housing modular switches , socket fan regulator and making good to disturbed surfaces including one run 1.5 Sqmm (nominal area) PVC insulated FRLS unsheathed multi-stranded copper conductor cable green in colour for earth continuity conductor and connected to common earth dolly complete for the following:-

One light point / fan Point controlled by one one way switch.

One bell/buzzer point controlled by one bell push on the same board with other switches or independent board. sqmm size

One 3 pin 5 Amp socket outlet on the same Board with other switch.

One 3 pin 5 Amp socket outlet on independent board.

Materials and Labour for Point wiring with 4.00 sq mm (nominal area) single core PVC insulated FRLS unsheathed multi-stranded copper conductor cable (maintaining colour code), 1100 volts grade in and including PVC conduits of suitable size but not less than 20 mm dia (medium grade) with all fittings and accessories concealed in walls/ceiling etc including cutting chases for conduits and including modular metal flush box for housing modular switches , socket fan regulator and making good to disturbed surfaces including one run 2.5 Sqmm (nominal area) PVC insulated FRLS unsheathed multi-stranded copper conductor cable green in colour for earth continuity conductor and connected to common earth dolly complete for one 3 Pin 15 Amps socket outlet on independant board all as specified and directed.

Supply and Fix modular switch,single pole,one way 10 Amp,240 Volts of make Anchor (woods white series with indicator Cat part no- 60019 or Havells switch with indicator cat part no-AHFSXIW101 of same specification complete all as specified and directed.

Supply and Fix Bell push, flush type, 5 Amp modular type complete all as specified.

Supply and Fix call Bell multi musical type 230Volt, AC complete all as specified.

Supply and Fix Digital Wireless doorbell receiver with one battery-operated transmitter with range upto 100m in open air AC, 230 Volts of make Havells model-TANGO WIRELESS DIGITAL DOORBELL Polyphonic or of equivalent make of said specifiaction approved by GE from list of approved makes.

Supply and Fix socket outlet, 6 Amps multi socket for 2 and 3 pin plug of Anchor Woods series Cat pat no-60106 HSN code-8536 240 volts /Havells/HPL complete all as specified and directed.

Supply and Fix Switches 20A rated with indicator of make Anchor cat part no-60064 HSN code 8536 or Havells/HPL of same specification complete all as specified and directed.

Supply and Fix socket 6A/16A 5in one modular type of make Anchor cat Part no-60109/60110 HSN code 8536 or Havells/HPL of same specification complete all as specified and directed.

Supply and Fix ceiling rose, surface, Bakelite, 65x50 mm two to three terminals complete all as specified.

Supply and Fix electronic fan regulator, rotary step type, tiny EME 100 W of make Anchor cat part no-60166 or Havells/HPL of same specification complete all as specified and directed.

Materials and Labour for Modular white Cover with frame 2 Module of make Anchor cat No-60304WH HSN code 8538 ,Havells/Honeywell/HPL with same specification all complete.

Materials and Labour for Modular white Cover with frame 3 Module of make Anchor cat No-60307WH HSN code 8538 ,Havells/Honeywell/HPL with same specification all complete.

Materials and Labour for Modular white Cover with frame 6 Module of make Anchor cat No-60313WH HSN code 8538 ,Havells/Honeywell/HPL with same specification all complete.

Materials and Labour for Modular white Cover with frame 8 Module of make Anchor cat No-61718WH HSN code 8538 ,Havells/Honeywell/HPL with same specification all complete.

Materials and Labour for PVC conduits of suitable size but not less than 20 mm dia (medium grade) with all fittings and accessories for Cable TV & Telophone lines complete all as directed.

Materials and Labour for Modular type RJ 45 socket all as per cat no 5e 360 20/200 with shutter - 1 module for Cable & Telephone all as directed.

Supply and Fix in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with single pole MCB 20 Amps complete all as specified.

Supply and Fix 10/12W environmental friendly ultra modern energy saving, surface mounted decorative oval bulk head edge lit LED luminaire including necessary connection with twin twisted unsheathed PVC copper cable of suitable size complete. Make Crompton/havells/Surya/Bajaj or equivalent as approved by GE from list of approved .makes.

Supply and Fix Batten integrated LED fitting, 20 W ,CCT/colours 6500K of Crompton cat part -Metal Ray Plus made up of metal body complete set including necessary connection with twin twisted unsheathed PVC copper cable as directed. or equivalent make as approved by GE from list of approved makes.

Supply and Fix Batten integrated LED fitting, 10 W ,CCT/colours 6500K of Crompton cat part -Metal Ray Plus made up of metal body complete set including necessary connection with twin twisted unsheathed PVC copper cable as directed. or equivalent make as approved by GE from list of approved makes.

Supply and Fix in repair 18 W ultra modern designed architectural LED 6000K Square Slim recess mounted PLUTO 1X1 igh efficacy 1x1 recess LED flat panel with high brightness LED for glare-free homogenous illumination including making required ceiling cutouts and connection with twin core unsheathed PVC copper cable incl earthing connection of suitable size complete Fixture size in mm (LxWxH) 295x295x70.. Make HAVELLS cat no PLUTO1X1PLR15WLED840S ,Bajaj,Wipro or equivalent as approved by GE from list of approved .makes.

Supply and Fix in repair energy saving & environmental friendly long life versatile pressure die cast aluminium IP66 roadway luminaire with high power LEDs 60 W within the premises including electric connection with twin core PVC insulated aluminium conductor, multistranded cable 2.5 Sqmm and testing complete as directed . (Make : Havells (ENDURAPEARLPLUSSL60WLED757SASYTOPC) or equivalent of make Bajaj/Philips/CG as approved by GE.

Supply and Fix in repair exhaust fans, single phase 230/ 240 V,AC, 250 mm sweep with louver of make Crompton cat -Brisk air or of equivalent make as approved by GE from the make of approved list.

Materials and Labour for shifting Room Air conditioning unit from one location to another with all accessories incl provn of brick work as and when required at site within the premises complete all as directed

Supply and Fix motor starter switch single phase 240V of 25Amp make Anchor cat part no 60157 or Havells/HPL/Legrand of same specifiacation comoplete.

Materials and Labour for Sub main wiring with two runs of 6 Sqmm (Nominal area) of single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor cables 1100 Volt grade drawn into and including PVC Casing Caping medium grade of adequate size but not less than 20mm in width and 1.2mm thick with all fittings and accessories, fixed to wall/ceiling etc including one run 4 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to earth dolly and mains complete all as specified and directed (Note :- PVC casing caping with two runs main cables and one run of earth wire will be measured as one length)

Materials and Labour for Sub main wiring with two runs of 4 Sqmm (Nominal area) of single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor cables 1100 Volt grade drawn into and including PVC Casing Caping medium grade of adequate size but not less than 20mm in width and 1.2mm thick with all fittings and accessories, fixed to wall/ceiling etc including one run 2.5 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to earth dolly and mains complete all as specified and directed (Note :- PVC casing caping with two runs main cables and one run of earth wire will be measured as one length)

Supply and Fix Sheet metal enclosure TPN Vertical Loadline (DB) for housing MCCB & MCBs, 8 way, double door, 415 Volts, with bus bar ,Neutral Link,Blaking Plate complete as specified and directed. (Make : L&T/ Legrand /Schenider or make from approved list)

Supply and fix Factory made Distribution Board for fixing MCB, SPN 8 way with 200 Amps rated bus bar,230 Volts, double door complete all as specified and as directed.

Supply and fix Factory made Distribution Board for fixing MCB, SPN 4 way with 200 Amps rated bus bar,230 Volts, double door complete all as specified and as directed.

Supply and Fixing MCCB, 63 Amps four pole 415 volts breaking capacity 18 KA fixed thermal and fixed magnetic setting complete all as specified and as directed .

Supply and fix MCB, SPN, 240 volts, 32 Amps 10 KA complete all as specified and as directed. Make : Indoasian Cat No. 811144 to 51 or equivalent as approved by GE from list of approved makes.

Supply and fix MCB, SP, 240 volts, 6 to 32 Amps 10 KA complete all as specified and as directed. Make : Indoasian Cat No. 811122 to 29 or equivalent as approved by GE from list of approved makes.

Supply and Fix in repair Fan hook suitable for hanging of ceiling fan, made out of MS flat 40x5 mm clamp duly welded/drilled, including nuts, bolts and washers complete all as required at site and as directed.

Supply and Laying in trenches/fixed to pole, wall etc LT under ground cable 1100 volts grade of size 50 Sqmm 3.5 core , XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded aluminium conductor all as per IS 7098 (Part-I) 1988, complete all as specified and as directed .

Excavation in trenches not exceeding 1.50 meter wide and not exceeding 1.50 meter in depth for foundation of electric pole, stay assembly, under ground cables etc and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceding 25 cm in soft/loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level not exceding 1.5m above the starting point complete all as specified and as directed.

Materials and Labour for sand cushioning to underground cable in trenches with clean dry (course) sand including filling, spreading and punning to desired thickness for protection of cable complete all as specified and directed.( Punned thickness will be measured).

Supply and Laying cable cover with sub class‘B’ old size over burnt bricks, laid dry and flat across the axis of cable, abutting each other with gaps between adjacent bricks not exceeding 10mm complete all as specified and as directed.

Supply and fixing in repair 50 mm bore GI pipe ‘light grade’ with all fittings for protection of cable laid in trenches, road crossing, drain crossing, under floor or fixed to iron structures/poles complete all as specified and directed.

Materials and Labour for Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6mm thick, buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m deep below normal ground level, connected with GI earth strip of size 25x4mm as earth lead up to test point by means of nuts, bolts, check nuts protected by and including GI pipe 40mm bore (light grade) and connected to main test point as directed and including concrete pit in PCC (1:3:6) type C-1, precast RCC (1:2:4) type B-1 cover slab 30cm x 30cm x 10 cm, reinforced with 8mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting, made out of 8mm dia TMT bar embedded in pre cast cover slab, funnel, wire mesh, 15mm bore GI pipe (medium grade) for watering, charcoal and salt in alternate layers, including necessary excavation and earth work in any type of soil complete all as shown on Electrical Plate No 3 of SSR Part-I, complete all as specified including taking down old one and as directed. Note : Rate quoted by tenderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 30x30 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing strip from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 40 mm bore light grade 7.5m.

M/S SEWAK SINGH