Proposed Construction of 4 Bedded Residential Quarter of 2 Block GPlus4 (4x2 Is equal 8 Units) for Judge Colony, Kanke Road, Ranchi

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classification of soil item - B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Supplying chemical emulsion in sealed containers including delivery as specified Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant atOMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing designation 75B one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I.

Providing designation 75 A brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints cost of screening materials, scaffolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75B brick work in CM (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials. raking out joints yo 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75 A brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 125mm thick reinforced designation 75A brickwork in C.M. (1:4) in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as sper building specification and direction of E/I.

Providing designation 100A brickwork with fly ash lime brick (FLAG) confirming to IS:12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carraige of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforced) all complete as per building specification direction of E/I.

Extra for brick work for EACH consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Second floor

Third floor

Terrace floor

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

1:2:4 (1 Cement :2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level. 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness), including attached pilasters, butterses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and struts ets. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floor, roofs having slope up to 15'' landing, balconies, shelver, chajjas , lintels, bands, plan window sills, staircases and spiral stair case above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick

Suspended floors, roofs, landings, balconies and access platform with water proofply 12 mm thick.

Weather shade,Chajjas, corbels etc. including edges

Stairs,(excluding landings) except spiral-staircasess.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid for SAIL & TATA STEEL)

Providing Tor steel reinforcement of 10mm, 12mm & 16mm mm dia. bars as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l.

10mm TMT FE 500 (only valid for SAIL & TATA Steel)

12mm TMT FE 500 (only valid for SAIL & TATA Steel)

16mm TMT FE 500 (only valid for SAIL & TATA Steel)

20mm TMT FE 500 (only valid for SAIL & TATA Steel)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 50 x 100 mm

Frame size 65 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood 50 x 20 mm

Providing and fixing bright /matt finished Stainless Steel handles ofa pproved quality & make with necessary screws etc all complete. 125 mm

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 12 mm thick

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete Twin rubber stopper

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1. 70 mm for Series R 1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.

Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (ii) Sites with structure height more than 20m for all wind speeds

Fixed window/ ventilator without mullion/ transom. Using R1 series with frame (33 mm & above) x (35 mm & above). (Height upto 0.90 metre)

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1. 70 mm for Series R 1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge.

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dime(L1) NSion i.e. in depth & width of profile shall be acceptable. Variation in profile dime(L1) NSion in higher side shall be accepted but no extra payment on this account shall be made.

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Three track three panels sliding door with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on two panels along with multi-point locking system, adjustable nylon rollers with SS 304 body.

Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (74 mm & above). (Height upto 2.5 metre).

Providing and fixing 6 mm thick High performance glass. door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-incharge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb

Supplying, fitting and fixing 35mm thick solid core type non decorative single leaf flush shutters in doors and windows with block board core blended with high quality pehnol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying fitting and fixing fully steel glazed doors, windows and ventilators of standard rolled 'Z' and mullion steel sections and size as per IS-1038, joints mitred and welded with 100x16x3 mm MS lugs fixed in cement concrete (1:2:4) blocks 15x10x10 cm , size including cost of oxidised iron fittings, with hinges, handle per steps , catch springs , 3 mm thick glass panes with alluminium beads and inner frame fixed with lugs with 20 mm long 6.3 mm gi counter sunk machine screw and nutsand applying a coat of red lead paints carriage to work site hosting and placing in position in all storied and taxes all comlete as per building specification and direction of E/I ;

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where material is not supplied by the deppt.)

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Supplying, fitting, and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10x 2mm at 100mm centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of 'T' iron 40 x 40 x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a apriming coat of red lead paint, carriage, hoisting and taxes all complete as per building specification and direction of E/I

Supplying, fitting and fixing 20 guage GCI sheet gate fitted on M.S> angle frame of size 60X60X6mm including cost of fabrication providing necessary locking arrangement with haskal and domny duly fixed in PCC (1:2;4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc,. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessry stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasterners etc,.)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed vitrified floor tiles polished finish of size Size of Tile 600 x1200 mm

Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18mm thick granite stone including machine polishing to edge to give high gloss finish etc, complete as per desing approved by Engineer-in-charge

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing 25mm thick first class patent stone flooring (1:2:4)with stone chips in two layers, bottom layer 19mm. thick (1:2.4)with 12mm to 6mm. size graded stone chips and top layer 6mm. thick (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty with all complete as per building specification and direction of E/1.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Extra for flooring work for each consecutive floor above first floor complete as per direction of E/I.

2nd floor

3rd floor

4th floor

Providing 12mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 and including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I

Providing 12mm Thick cement plaster (1:6) with clean coarse sand F.M. 1.5 including screening, curing with all lead and lifts of water, scaffolding, taxes and royalty, all complete as per building specifications and direction of E/I

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Making 6x6mm grooves in plaster surface over walls truely horizontal or vertical as specified. at regular intervals, at all heights including cleaning, finishing, scaffoding and curing wth all leads and lifts of water all complete as per building specification and direction of E/|

Providing & laying water proofing treatment in sunken portion of WCs, bathrooms etc. by applying cement slurry mixed with Armourcrete of M/S The Structural Water Proofing Company PVT. Ltd.or Tapecrete of M/s CICO Engg. Servce consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with Armourcrete or Tapecrete @ 0.125 kg/ sq.m. This layer will be allowed to air cure for 4 hours

(b)second layer of slurry of cement @ 0.242 kg/sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/ sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preperation of surface, treatment& sealing of all joints, corners, junctions of pipes & masonary with polymer mixed slurry.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building speicification and direction of E/I.

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 150mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 andapproved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishingthe surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“Allabove operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoirs, sewage and water treatment plant, tunnels/subways, and bridges etc. prepared by mixing in the ratio of 5:2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3:1 (3 parts integral crystalline slurry : 1 parts water) for horizontal surfaces and applying the same from negative (internal) side with the hlep of synthetic fiber brush. The materials shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 ad resistant to 16bar hydrostatic pressure on negative sides. The crystalline slurry shall be capable of self healing the cracks upto width of 0.50mm. The work shall be carried out all complete as per specification and direction of E/I. The product performance shall carry guaranteed for 10 years against any leakage

For Vertical Surfaces two coats @ 0.70 kg per SQM

For Horizontal Surfaces two coats @ 1.10 kg per SQM

Water proofing treatment of RCC sunshade with Zycosil/equivalent water proofing Solution (1 litre of Zycosil/equivalent & 20 litres of water stirred first & 2 litres of Zycoprime/equivalent added and stirred (total 23 litres)) till it meets the saturation level and testing as per RILEM or by water drops test in which water drops do not absorb but drops remain or rolls.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm. with average minimum thickness of 55 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) over PVC sheet1mx1mx400 micron, finished with12 mm cement plaster1:3 (1 cement : 3 fine sand) and a coat of neat cement, roundingthe edges and making and finishingthe outlet complete

Providign and applying Plaster of Paris Putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of oil borrnd distemper of approved shade and Make over a coat of cement primer over new surface inluding preparing the plasterecl surface by rubbing wmooth with pumice stone or fine sand paper applylng putty wherever required scaffolding washing of floors and taxes all complete as per buiiding specifica tionand drrection of E/1..

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plarstered surface by rubbing smooth with pumice stone or fine sand paper, appiying putty wherever required, scaffolding washing of floor and taxes all complete as per buiiding specification and drrection of E/i.

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with premium acrylic smooth exterior paint with sillicone additives of requited shade . New work : 2 or more coats applied @1.43 Ltr/10sqm over and including base coat of waterproofing cement paint applied @2.2 Kg/10 sqm

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surfaces including preparing the surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes, all complete as per building specifications and direction of E/I

Providing French spirit polishing over new.wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt scales, smokes, grease and sand papering, including cost of scaffolding and taxes, all complete as per building specifications and direction of E/I

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Single Tee with door 110x110x110 ,mm

Bend 87.5 degree 110x110x110mm

Shoe (Plain) 110mm shoe

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse send : 6 graded stone aggregate 20 mm nominal size ) over 75 mm thick bed of dry brick ballast 40 mm nominal size ,wall rammed and consolidated and grouted with fine sand including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured

Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Carriage of materials

Bricks (1K+ 7P = 8 KM.)

Coarse Sand (15 KM.)

Stone Chips ( 15 KM.)

Stone Metal ( 15 KM.)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board 610x510 mm bowl depth 200 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe, 40 mm dia

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length , 15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Supplying, materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Providing and placing on terrace (at all floor levels) (PVC) Polyethylene water storage tank ISI 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

External work - 40mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete.

Semi rigid pipe

32 mm dia

40 mm dia

Providing and fixing square mouth S.W. gully trap grade 'A' complete with C.I. Grating brick masonary chamber with bricks of class designation 75 and water tight C.I. Cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design

100x100 mm size P type . with common burnt clay F.P.S.(non module) brick of class designation 7.5

Constructing brick masonary road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:4 (1 cement :4 coarse sand ) including 500x450 mm precast RCC horizontal grating with frame complete as per standard design . with common burnt clay F.P.S.(non module) brick of class designation 7.5

Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I. ( Add 15%)

Slotted cowl (terminal guard) 100 mm dia

Floor trap - 100mm dia.

Ring rubber

Door piece

Supply, fitting and fixing Central hole basin mixure without popup waste system

Supply, fitting and fixing Towel ring

Supplying and fixing C.I. cover without frame for manholes : 560 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

External work - 50mm nominal bore

External work - 65mm nominal bore

External work - 80mm nominal bore

Making Connection of GI distribution with GI main following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete.

25 to 40mm nominal bore

50 to 80mm nominal bore

Providing and fixing gunmetal gate valve withCI wheel of approved quality (Screwed end)

50mm dia nominal bore

65mm dia nominal bore

80mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonary chamber 60x60x75cm, inside with 75 class designation brick work or Equilent precast concrete block work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock with C.I. Surface box 100x100x75 mm ( inside) with hinged cover fixed in cement concrete slab 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement:5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design with F.P.S. bricks.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

300 MM dia R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

150mm diameter S.W. pipe

250 mm diameter S.W. pipe

Constructing Brick Masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.

0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)

with common burnt clay F.P.S.(non module) brick of class designation 7.5 or Equilent precast concrete block work

Extra depth for circuler type manholes 0.91 m internal dia ( at bottom ) beyond 0.91m to 1.67 m .

With F.P.S. bricks class designation 75 or Equilent precast concrete block work

Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc. And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.

All kind of soil Pipes, cables etc, exceeding 80mm dia but not exeeding 300 mm dia

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Point Wiring in Medium Class PVC Conduit, with Modular type Switch:-

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed with PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) :- Make:- Havells, Polycab, Rajnigandh, RR Cable. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor(WOODS), Schneider-(OPEL) Group-B

Twin Control Point Wiring in PVC Conduit, with Modular type Switch:- Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed Medium Class PVC conduit, 2 way modular switch, modular plate, suitable size of GI box earthing the point with 1.5 Sq. mm FR PVC insulated copper conductor single core cable etc as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) :- Make:- Havells, Polycab, Rajnigandh, RR Cable. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor(WOODS), Schneider-(OPEL)

Power plug wiring in PVC conduit (2x4 sq.mm.):- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor single core cable in surface/recessed Medium Class PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) Make:- Havells, Polycab, Rajnigandh, RR Cable.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper condcutor, single core cable in surface/ recessed Medium Class PVC conduit as required. FR PVC Copper Wire (Confirming to IS: 694-2010, 1.1 KV) Make: Havells, Polycab, Rajnigandh, RR Cable.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sq mm earth wire

2x6.0 Sq.mm + 1x6.0 Sq.mm earth wire .

4x6.0 Sq.mm + 2x6.0 Sq.mm earth wire.

4x10 Sq.mm + 2x6.0 Sq.mm earth wire.

TV Cable in Existing Conduit:- Supplying and drawing Co-axial TV Cable RG-6,0.7mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required. (Confirming to IS: 694-2010, 1.1 KV) Make:- Havells, Polycab, Rajnigandh, RR Cable.

S/F PVC Conduit: Supplying and fixing of following sizes of med Class PVC conduit of 2 mm thick along with the accessories in surface / recess & cutting the wall and making good the same in case of recessed conduit as required . (Make:- Polycab, Precision, AKG)

Supply and fixing of following size PVC/G.I. box on surface /recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

S/F Modular type Switch / Socket:- Supplying and fixing of following switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make of Modular switch Sockets:- Havells (ATHENA), L&T ENGLAZE), Legrand (LYNCUS) , Anchor (WOODS), Schneider-(OPEL)

5/6 amps switch

15/16 amp switch

3 pin 5/6A socket outlet

6 pin 15/16 amp socket outlet

TV antenna socket outlet

S/F Modular type electronic fan regulator:- Supplying and fixing 2 modules Stepped type electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as requried. (Make :-Havells, Legrand , Anchor, Schneider.)

S/F Modular blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (Make - Havells, Legrand , Anchor, Schneider.)

Supply and fixing of following size/ modules, GI box along with modular base & cover plate for modular switch/ regulator in recess, including connection as required. (Make :- Havells, Legrand , Anchor, Schneider).

1or 2 module (78mmx 78mmx 45mm)

6 module (78mmx 205mmx 50mm) (for 2 nos. 6A Sockets & 2no. 6A Switch)

S/F Light plug point with modular type accessoris:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 Amp modular socket outlet and 5/6 A modular type switch, connections painting etc. as reqd. (for Light plug point). (Make:-Havells, Legrand , Anchor, Schneider, L&T.)

S/F Power plug ponit with modular type accessories:- Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 Amp modular socket outlet and 15/16 A modular type switch, connections painting etc. as reqd. (Make:- Havells, Legrand , Anchor, Schneider, L&T.)

S/F Ceiling Rose:- Supplying & fixing of 2 pin, 5 amp Ceiling rose on the existing junction box/ wooden block including connection etc. as required. (Make:- Anchor, Kona)

S/F Batten / Angle Holder:- Supplying and fixing brass batten/angle holder including connection etc. as required. (Make:- Anchor, Kona)

S/F Electronic Musical Call Bell. Supplying and fixing of Electronic Musical call bell suitable for single phase, 230 V, complete as required. (Make:- Anchor, reputed)

ITC fluorescent fitting directly on surface:- Installation, testing and commissioning of suspended pre-wired ,fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc., directly on ceiling or on wall including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC ceiling fan:- Installation, testing and commissioning of Ceiling fan, icluding wiring the down rods os standard length (Up to 30Cmm) with 1.5 sq. mm FR PVC insulated, copper conductors, single core cable etc. as required.

ITC exhaust fan upto 450 mm sweep:- Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F MCCB in Panel Board:-Providing and fixing following rating and breaker capacity MCCB with thermomagnetic release and thermal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 25-100 amps, 16 KA fixed thermal setting

S/F SP MCB DB:- Supplying and fixing following way, SP&N MCB doubel distribution board of sheet steel for 240 Volts on surface /recess complete with tinned copper bus bar, neutral busbar, earth bar, detachable gland plate, interconnections, phophatized and powder coated painted including earthing etc. as required ( But without MCB/RCCB/ ISOLATOR). (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU)

8 Way Double Door

12 Way Double Door

16 Way Double Door

S/F TP MCB DB: - Supplying and fixing following way, horizontal type double door three pole & neutral, sheet steel, MCCB distribution board, 415V, on surface/ recces , complete with tinned copper bus bar, neutral bar, earth bar, din bar interconnections, powder painted including earthing etc. as required (But without MCCB/RCCB/Isolator)

6 ways (4+18) Double Door. (horizontal type)

8 ways (4+24) Double Door. (horizontal type)

S/F VERTICAL TYPE T.P. MCCB DB:- Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCCB distribution board of sheet steel dust protected, duly power painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar mounting MCCB's (but without MCCB's and Incomer) as required. Note : Vertical type MCCB TPDB is normally used where 3 phase outlets are required. (Make:-SIEMENS-Bitaguard, LEGRAND-Ekinox³-, SCHNEIDER-ACTI-9, L&T-AU 4 way (8 + 12) Double door, Vertical Type

S/F 'C' Series MCB:- Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, 'C' curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. ( Make:-LEGRAND- DX³/SCHNEIDER- ACTI-9/ABB-S200MSIEMENS- BETA GUARD/ L&T- AU VERSION).

6-32 Amps. Single Pole

6-32 Amps Double Pole

40 Amps Double Pole

6/32 Amps TPN

50/63 Amps TPN

S/F SP MCB Blanking Plate:- Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.(Make:- L&T, Legrand, Schneider,Siemens)

S/F SPN RCCB:- Supplying & fixing following rating double pole (Single Phase & Neutral) 240 V, Resudual Curren Circuit Breaker (RCCB) , having a sensitivity current uo to 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (Make:- LEGRAND- DX³/SCHNEIDER- ACTI-9/ABB-S200MSIEMENS- BETA GUARD/ L&T- AU VERSION.) 63A

S.F 20A SPN MCB Industrial Socket Out Lets:- Supplying and fixing of 20Amps , 240 Volts, SPN industrial type Sockets outlet , with 2 pole and earth, metal enclosured plug top along with 20A 'C' series SP MCB insheet steel enclosure, on surface or in recess, with chained metalcover for the socket out lets and complete with connections, testing and commissioning etc as required.

P/F MV Danger Notice Plate:- Providing & fixing of M.V. danger notice plate of 200 mm x 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.

Providing & fixing of H.T. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.

G.I. Pipe Earthing:- Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and providing massonry enclosure with cover plate having locking arragement and watering pipe etc. with charcoal/cock and salt as required.

S/L 25mmx5mm G.I. strip as strip earth electrode:- Supplying and laying 25 mm X 5 mm GI strip at 0.50 meter below ground/surface as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm).

P/F G.I. lighting conductor finial:- Providing and fixing of Lightning Conductor finial, made of 25 mm dia 300mm ling, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Reverting, Sweating and soldering Lightning Conductor Tape:- Reverting, Sweating and soldering of Copper/G.I. Tape (with another Copper/G.I. tape, base of the finial or any other mettalic obect) as requried.

P/F G.I. lightning conductor tape in horzontal run :- Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface of the wall for lightning conductor complete as required. (for Horizontal Run).

P/F G.I. lightning conductor tape in Vertical run:- Providing and fixing G.I. Tape 20mmx3mm thick on parapat or surface of the wall for lightning conductor complete as required. (for Vertical Run).

P/F Testing joint for GI lightning conductor :- Providing and fixing testing joint made of 20mm * 3mm thick GI strip 125mm long. With 4 nos. of GI bolts. Nuts chuck nuts and spring washers etc. complete as required.

G.I. Pipe electrode with Salt/Charcoal:- Earthing with G.I. Earth Pipe 4.5 Meter long , 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arragement and watering pipe etc. with charcoal and salt as required.

S/L 25 x 5mm G.I. earth strip in 50 mm below ground:- Supplying and laying 25mmx5mm G.I. Strip at 0.50 meter below ground as strip earth electrode, including connection/ termination with G.I. nut bolts, spring washer etcas required. (Jointing shall be done over and 2 sets of G.I. Nut Bolts & Spring washer spaced at 50mm).

MV Cable Laying up to 35 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required.

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 35 sq.mm. but not exceeding 95 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

MV Cable Laying up to 185 sq. mm. in ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required

Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 185 sq.mm. but not exceeding 400 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

MV Cable one no. additional Laying up to 35 sq. mm. in ground :- Laying of one number additional PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq.mm. direct in ground including excavation, sand cushioning, protective covering by 2nd class bricks and refilling the trench etc as required.

MV Cable One Number additional Laying up to 400 sq. mm. in ground ;- Laying of one number additional PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 185 sq.mm. but not exceeding 400 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

CABLE ROUTE MARKER:- Supplying and making cable route marker with cement concrete 1:2:4 (1 Cement :2 Coarse sand ;4 gradced stone aggregate 20mm nominal size ) of size 60cmx60cm at the bottom and 50cmx 50cm at the top with a thickness of 10 cm including inscription duly engraved as required.

Supply, installation, testing and commissioning of of following size ceiling fan 3 blades confirming to IS:- 374:2019 including wiring tne down rods, of standard length (up to 30 cm) with 1,5 FR PVC insulated, copper wire suitable for 230 Volts, 50 Hz, single phase supply etc. complete as required.( BLDC 5 Star (32 Watt) IS:374:2019 (energy efficient fans and two yeas warranty ) (Make & Model nos. of Fans are to be approved by Engineering Incharge & Consultant before procurement.)

Supply of 48" (1200 mm) Sweep Ceiling fan BLDC 5 Star (32 Watt) IS:374:2019 (energy efficient fan. Make :Usha/Crompton/ Havells/GEC.

Supply of 56" (1400 mm) Sweep Ceiling fan BLDC 5 Star (32 Watt) IS:374:2019 (energy efficient fan. Make :Usha/Crompton/ Havells/GEC.

SITC of 230 mm (9") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Polar/Usha/Crompton / Havells.

SITC of 300 mm (12") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Polar/Usha/Crompton / Havells . .

LED LIGHT FIXTURES

All the LED lamp shall be of minimum 60 or above lumens per watt and the LED BATTEN TUBE LIGHTS & other LED light fixtures shall be of 100 or above lumens per watt. LM 79 and LM 80 reports need to be submitted with all accessories by the contractor. All LED Lights (Make & Model nos. of LED Liughts are to be approved by Engineering Incharge & Consultant before procurement.) Burning Hours should be less than 35000 to 50000 hrs. Make:-Havells/Sygnify-Philips/ Bajaj/ Jaquar .

SITC of following rating recess/surface mounted LED round/square shape Down Light Luminarie with pressure die-cast housing for single phase supply voltage. Luminarie shall be confirm to IS; 10322 part-5/section-2 or IEC 62722 with all necessary accesoreies as required. (100l/w , 5700K Cool white, rated voltage- 220/240V. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philips/Bajaj/ Jaquar. Make 0f LED Philips/Osram/Cree/Nichia.

12 W Round Surface Down light

15/16 W Round Surface Down light

SITC of following rating surface mounted LED 4ft Batten tube light fitting suitable for 230V, 50 Hz, single phase supply etc all complete as required. wall mounted LED type batten fitting complete with electronic diver and LED etc. directly on wall including connections with 1.5 Sq. mm FR PVC insulatted copper conductor and earthing the body etc. as requiered. (LM 79 and LM 80 reports need to be submitted , 50,000 burning hrs, and two years warranty) Make:-Havells/Philip/ Wipro/ Jaquar

20/22 W LED Tube Light (4 FT) Batten type.

Supply of 9W/10W LED Bulb in existing holders. (Confirming to IEC : 62722)

SITC of LED 2 ft Mirror light with power 8/10W, rated voltage 230W, 50 HZ, aluminium /PC body with running life minimum 30000 hrs. ( LM 79 and LM 80 reports need to be submitted)

Supplying and fixing Surface mounted 9/10 Watt CFL / LED type bulk head e comprising of pressure die casr housing with acrylic diffuser (IP65) and complete with integrated electronic driver etc. directly on wall /ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc as required.

SITC of 4 to 6Watt LED Foot Lamp/LED Step Light cast alluminium body and IP-54, protection

Building Outer Light (45/48W LED) :-

Supply, fitting, fixing and testing of building outer lighting luminaire aerodynamically shaped single piece pressure die-cast Aluminum luminaire with high power LEDs as light source and electronic driver (IP65), along with 45/48W LED Lamp, as Energy saving as per drawing prescribed reflector and heat resistant toughened flat glass cover, with 5ft long 40mm dia G.I. pipe with 3 Nos. of iron clamps , anchor nut bolts with double washers as per direction of E/I or consultant as per drawing prescribed reflector and heat resistant toughened flat glass cover (IP-65) and in compliance to IEC Safety Standards. LM 79 and LM 80 reports to be submitted with all accessories. Make:- Havells/Philips- Signify/Bajaj/Jaquar Make 0f LED :- Philips/Osram/Cree/Nichia.

Supply fitting and fixing of PVC/XLPE insulated PVC sheathed heavy duty Al. armoured cable for working voltage up to and including1100 Volts confirming to IS 1554 (part-1)Make:- Havells, KEI, Finolex, Polycab.

2 Core 6 Sq. mm

4 Core 10 Sq. mm

3.5 Core 25 Sq. mm

3.5 Core 185 Sq. mm

3.5 Core 35 Sq. mm

3.5 Core 95 Sq. mm

3.5 Core 120 Sq. mm

3.5 Core 300 Sq. mm

LED Street Light :- SITC of following rating LED Street Light luminarie with pressure die cast housing and loughened glass cover (IP-66 Protection) in existing pole /pipe for supply voltage 100- 270V, AC, 50Hz, . Luminarie shall be confirm to IS:- 10322 (Part-5/Section-3 and shall be complete with all necessary accessories as required.

LED FLOOD LIGHT:- SITC of following rating LED Flood Light luminarie with presure die- cast housings and loughened glass cover (IP-66 Protection) in existing pole /pipe for supply voltage 100- 270V, AC, 50Hz, . Luminarie shall be confirm to IS:- 10322 (Part-5/Section-3 and shall be complete with all necessary accessories as required. (200W/4000K) 200W LED FLOOD LIGHT (4000K)

Post Top LED Lamp (for Gate) SITC of following rating LED Post Top Lamp made in die- cast aluminiumn with Clear /Opal acrylic diffuser (IP-66 Protection) on existing including connection with 3x 1.5 Sq. mm PVC Copper conductor etc all complete as required.

LED Bollard Fitting :- SITC of following rating approved make LED Bollard fitting with cylindrical ssape of height 600 t0 850mm power in put 8/9 Watt die cast aluminium housing opel with PC diffuser , IP65/54 protection, confirming to IS:- 10322 part-5 etrc. Complete as required . (Excluding plinth charges.)

Supply of 7 Meter Height Octagonal Hot Dip Galvanized pole (BOP 7030) with top dia 70mm bottom dia 130mm & made of 3 mm thickj sheet, base plate dimensions 200x200x12mm (L X B X T) including suitable sizes of foundation bolts all complete as required. (Without ARM) Make:-VALMOUNT, TRANSRAIL,BAJAJ,/RR ISPAT..

Installation, Testing and commissioning of 7 Meter Height Octagonal Hot Dip Galvanized pole with suitable Tools and Plants, wiring of Luminaires with all materials and construction of shallow foundation, with M25 grade concrete considering safe soil bearing of 10T/mtrs Sq.

Supply fitting, fixing of Single Arm (1 Mtr. Long) suitable for 70 mm Top. Make:- VALMOUNT, TRANSRAIL,BAJAJ,/RR ISPAT..

Supply fitting, fixing of Double Arm (2 Mtr. Long)suitable for 70 mm Top. Make:- VALMOUNT, TRANSRAIL,BAJAJ,/RR ISPAT..

Supplying and fixing of following switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as reqd. Bell push

Supplying & fixing 5 amps to 32 amps rating 240/415 volts 10 kA, C curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple Pole

1.1 KV Cable End Termination:-Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

2 core 6 Sq. mm. (19mm)

3.5 Core 25 Sq. mm. (28mm)

3.5 Core 35 Sq. mm. (32mm)

3.5 Core 95 Sq. mm. (45mm)

3.5 Core 120 Sq. mm. (45mm)

3.5 Core 185 Sq. mm. (57mm)

3.5 Core 300 Sq. mm. (70mm)

4 Core 10 Sq. mm. (25mm)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc. as required

50 mm dia (DSR-2018)

80 mm dia (CSR-2018)

100 mm dia (DSR-2022)

62.5 KVA Silent D.G. Set with AMF Panel IS/IEC - 60034-1, IS:1460, IS:13018 :-

Supply, fitting, fixing, installation and testing of 62.5 KVA /415 Volts, 3 Ph. Silent Diesel Generator Set with AMF Panel confirming to IS/IEC - 60034-1, IS:1460, IS:13018

The 62.5 KVA /415 Volts, 3 Ph. Silent Diesel Generator Set with AMF Panel shall have AC supply complete with engine (1500 RPM) and alternator with accessories including residential type silencer and fuel service tank, battery, nattery leads, battery charger with all accessories, including MCCB of suitable rating & standard set of tools and anti-vibration mounting pads, etc. The power command controller compactable with BMS, PC & PLC compelte as required, remote mointoring and data logging with digital voltage regulator through inbuilt AVR, digital governing including protection complete as required. Make:-Kohler/Jakson/Sterling, KOEL-Green (Kirloskar Oile Electric Limited)

Supply of company make acoustic enclosure for 62.5 KVA CPCB approved Acoustic enclosure with 80 mm MS base plate, 2 mm CRCA sheet, 50 mm thick foam / 100 mm Rock Wool Insulation, 14 surface tank treatment, dully powder coated and painted with suitable colour with integrate Fuel Tank, services door, louvers (Fresh Air / Radiator), 1020 dia residential type Silencer, dimension as per company specification, complete with following accessories :-

a) Fuel Tank.

b) Batteries, battery leads and in built battery charger.

c) Residential Silencers.

d) First fill of lube oil.

e) AVM Pads.

f) OEM Manufacured AMF Panel with 200A /FP/36kA/MCCB /Microprocessor release.i( with nbuilt Control Breaker ( of suitable capacity of 200A MCCB Microprocessor release type with spreader links & extended rotary handle) and all type of meters (Voltmeter, Ammeter, KW/m, Hz/m, contractor, AMF Conroller etc as required ) and all other protections.

In above supply item following work are also included :- i) Installation, fitting, fixing, testing and commissioning of the same. ii) Civil part for commissioning of D.G. Set as per civil rates for construction of platform. (Foundation of Platform shall be in he scope of Civil Part) iii) Installation of Exhaust system for D.G. Set shall be as per Central & State Pollution Board Norms (C.P.C.B. norms). iv) Test run for D.G. Set without load and with load (part wise ) at least 2hrs each time shall be in the scope of Contactor.

Supply of inbuilt Control Breaker (of suitable capacity of 200A/36KA/FP MCCB Microprocessor release type with spreader links & extended rotary handle) with separate AMF Panel having 200A F/P MCCB, Microprocessor release type with spreader links & extended rotary handle, AMF Controller, F/P NO NC 200A Contactor, and all type of meters (Voltmeter, Ammeter, KW/m, Hz/m) and all protection indications with alarm and with suitable arrangement for 1R 120 Sq mm 3.5 Core Al. Ar. Cable etc as required.

Cost of 62.5 KVA DG set with AMF Panel

Supply, Installation, Testing and Commissioning of electric driven, centrifugal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC with IP 55 Protection for enclosure, horizontall foot mounted with class F insulation , complete in all respect as required or as directed by engineer incharge. Terrace Booster Pump

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3 × 50 sq.mm.(aluminium)

3 × 6 sq.mm.(aluminium)

2 × 1.5 sq.mm. in Conduit

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

65 mm diameter

80 mm diameter

100 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc. 100 mm diameter

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge.

100 mm diameter

80 mm diameter

65 mm diameter

50 mm diameter

40 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required.

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required.

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required.

Providing and laying Cables for Fire alarm System , 2 core x 1.5 sq mm armoured cables in surface , or flexible cables in PVC conduit (for conduits placed in ceiling/wall).

Supply, Installation, Testing and Commissioning of electric driven, centrifugal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC with IP 55 Protection for enclosure, horizontall foot mounted with class F insulation , complete in all respect as required or as directed by engineer incharge.

Main Fire Pump

Jockey Pump

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Pump Room

Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.

150 mm diameter

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge.

150 mm diameter

100 mm diameter

80 mm diameter

25 mm diameter

Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes ,royalty etc all complete job as per direction of E/I.

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 50 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage complete (by mechanical transport upto 5Km lead) (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage complete (by mechanical transport upto 5Km lead) (manure measured in stacks will be reduced by 8% for payment): Screened through sieve of I.S. designation 16mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing of the Ground.

Spreading of sludge, dump manure or/and good earth in required thickness as per direction of officer-in-charge (Cost of sludge, dump manure or/and good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the officer-in-charge.

Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm. efilling the excavated earth after breadking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, with in a lead of 50m lift up to 1.5 m complete (cost of sludge, manure of extra earth to be paid for separately). Around Outer & Inner Length of Bondary Wall

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately):

Holes 1.2 m dia and 1.2 m deep.

Holes 90 cm dia, and 90 cm deep.

Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge.

Trees for 300 No. (4-8 & 5-6 year Slow & Fast growing group) ( 18 Manth Per Tree 175x 18 = 11484.00)

Half brick circular tree guard in bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20 m below ground, bottom two courses laid dry and top three courses in cement mortar 1:6 (1 cement : 6 fine sand) and the intermediate courses being in dry honey comb masonry as per design complete: With common burnt clay F.P.S. (non modular) bricks of class designation 5

TREES

Alstonia scholaris of plants height 150-165 cm. in bag of plants size 25 cm

Azadirachta indica ( Neem ) of plants height 120-130cm in big polybag of plants size 25 cm

Cassia fistula (Amaltash) of plants height 120-135 cm. in big poly bags of plants size 25 cm

Delonix regia (Gulmohar) of plants height 150-165 cm. in big poly bags of plants size 25 c

Ficus benjamina (green) of plants height 120-135 cm. with 6-8 branches and lush green foliage in gunny bags of plants size 25 cm

Fishtail palm of plants ht. 150-180 cm bottom girth 15-20 cm well developed in big poly bags of plants size 25 cm

Foxtail palm of plants ht. 120-150 cm bottom girth 15-20 cm well developed in big poly bags of plants size 25 cm

Jacaranda mimosifolia of plants height 150-165 cm. in big poly bags of plants size 25 cm

Mangifera indica (Mango-grafted ) of plants height 60-75 cm. in big poly bag of plants size 25 cm

Plumeria alba of plants height 120-135 cm. with 2-3 branches in bags of plants size 30 cm

OKNAMENTAL PLANTS

Providing Plant Dahlia single in different colour with fresh & healthy foliage well developed with 6 to 8 half blooming buds in 20 cm Earthen Pot/Plastic Pot.

Providing Plant Daisy well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/Plastic Pot.

Providing Plant Salvia red Hybrid dwarf variety having 15 to 23 cm ht., specimen 6 plants with fresh & healthy foliage in full bloom well developed in 35 cm Earthen Tray/ Nand

Providing Plant Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot,

Washingtonia filifera palm well developed 90 to 105 cm ht. plant having 5 to 6 straight fresh and healthy leaves in 35 cm Cement Pot

SHRUBS

Supply and stacking of plant Cassia biflora of height 45-60 cm. in earthen pots of size 20 cm

Supply and stacking of plant Ficus panda of height 30-45 cm. with 3-4 branches and healthy foliage in p.bag of size 20 cm

Supply and stacking of plant Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm

Supply and stacking of plant Hibiscus variegated of height 60-75 cm. with healthy variegated foliage in earthen pots size 25 cm

CREEPER PLANTS

Allamanda cathartica plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots

Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan, Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots.

Quisqualis indica plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots

FOLIAGE/SHADE LOVING PLANTS

Providing of Areca Palm plant, having ht. 1.20 m to 1.50 m with 5 to 6 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot.

Providing of Areca palm plant, having ht. 1.50 m to 1.80 m with 6 to 8 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot.

Providing of Croton Golden plant, having ht. 45 cm to 60 cm with 2 to 3 branches, well developed, fresh and healthy foliage in 25 cm size of Earthen pot / Plastic pot.

Providing of Diffenbachia Tropicsnow plant, having ht. 60 cm & above with 8 - 10 leaves, well developed, fresh & healthy in 25 cm size of Earthen pot / Plastic pot.

Providing of Draceana Song of India Green plant (three in one), having ht. 30 cm, well developed, fresh & healthy, lush green foliage from bottom to top in 20 cm size of Earthen pot / Plastic pot.

NON SCHEDULE ITEMS Providing and fixing Camp Jali Size-200 mm x 200 mm x 60 mm thick all complete as per building specification and direction of E/l.

Providing and fixing 1mm thick Normal Suede 5333 Size- 8ft x 4ft Laminates all complete as per building specification and direction of E/l.

Providing and fixing Mortise Lock with NEH 17 Rossette Handle set 2479 and 240mm Lock body 8448 with 1CK 60 mm Ultra XL+ 4231 Cylinder in complete set

Providing and fixing Mortise Lock with NEH 17 Rossette Handle set 2479 and 240mm Lock body 8448 with 40 mm half Cylinder 7598 in complete set

Providing and fixing 8083 , 6 Lever mortise lock with Lockset 70mm, Backset 48.5mm, CD 57mm, Square Forend 155x20mm, Latchbolt Throw 9mm and Deadbolt throw 14mm. Easy latchbolt reversible option. Handle Coverplate 200mm. Material Steel for Forend Plate, Striker, Case and Cover. Brass Latch bolt and Deadbolt. Zinc alloy Handle Coverplate. Finish textured black for Case and Cover. Handle Cover plate in Electroplated Satin Nickel finish. 2 Steel keys with Chrome plating. Suitable for 30mm to 45mm thick doors. Complete set including the fixing accessorie

Providing and fixing 2478 NEH 17 Baby Latch without locking mechanism

Providing and fixing2730 Designer Tower Bolt-100mm

Providing and fixing 2731 Designer Tower Bolt-150mm

Providing and fixing 3261 SS Tower Bolt-150 mm

Kitchen Area Approx 10 feet X 12 Feet Kitchen Sink - Fanke Make - Single Bowl with drain Board Kitchen Gas Burner - Faber - 3 burner GLASS TOP Kitchen - Faucets - Faber - 1 no KITCHEN Lower Area - Approx 36 Sq ft Kitchen Hardware - Ebco Make, Auto Hinges-SS304 Slow Motion, Corner Hinges Slow Motion, Basket-SS304, Pro-motion Drawers, Handle-Profile, Screws, etc Kitchen Lower Caracas-Ply Board with both side inner white liner laminate, machine pressed boards and 4 side Edge Band of Same colour. (as required) Kitchen Shutters-High Gloss Mica Or Plane Matt finish Wooden type laminate, back side white laminate with 4 side edge Band. 1 KITCHEN Upper Area - Approx 20 Sq Ft Kitchen Hardware-Ebco Make, Hinges-SS304 Slow Motion or Top Lift Pumps, Screws, etc Kitchen Caracas-Caracas-Ply Board with both side inner white liner laminate, machine pressed boards and 4 side Edge Band of Same colour. (as required) Kitchen Shutters-High Gloss Mica Or Plane Matt finish Wooden type laminate, back side white laminate with 4 side edge Band. Or also Aluminium Door Shutter if required (As per drawing) with 4 mm glass. LOBOUR - installation and commencement to finishing of wood work in kitchen

Wardrobe - Door System Wardrobe. Wardrobe- Caracas-Ply Board with both side inner white liner laminate, machine pressed boards and 4 side Edge (as required) Band of Same colour Wardrobe Shutters-High Gloss Mica Or Plane Matt finish Wooden type laminate, back side white laminate with 4 side edge Band Wardrobe Hardware - Ebco Make, Auto Hinges SS304 Slow Motion, Locks, Wardrobe Rail, Drawer Locks, Drawer Channels-Slow Motion Extra Wardrobe fittings as be actual cost. Coat Pull-Out Hander, Wardrobe Organiser, Saree / Trouser Pullout, Shoe Rack, LED Wardrobe Lights, etc

Providing, fixing, and installing, 8 passenger elevator, Lift well size - 1750(W) x 1700 (D), No. of Stops - 5, Openings-5, Ground Floor to 4th Floor Height- 3.0 M, Clear Door Opening- 800mm, Speed of Lift - 1.25 M/s, Vision Panel, Automatic rescue device, etc., with all necessary features,WITH machine room, Stainless Steel Car Cabin, all complete as per specification and instruction of Engineer in charge. The work also include all building/ structural works for supporting arrangement system, necessary scaffolding required for erection of the complete system, necessary wiring and installation of lighting for lift well and lift pit, providing ladder in the lift pit etc. as required complete. (Rate -1584745.76 + Add 10% ( CP) = 1743220

Providing and fixing white vitreous wall mounting water closet with Uf Soft Close Slim seat cover hinges of size 345X495X365 mm of approved shape including providing & fixing white vitreous concealed cistern with dual flush fitting, of, including seat cover, flush plate and cistern fittings, nuts, bolts and gasket etc complete. Model no. Essence Neo 100% Rimless 92559

Providing and fixing white vitreous wall mounting water closet with Uf Soft Close Slim seat cover hinges of size 345X495X365 mm of approved shape including providing & fixing white vitreous concealed cistern with dual flush fitting, of, including seat cover, flush plate and cistern fittings, nuts, bolts and gasket etc complete. Model no.Fabio Rimless 92559

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-Model no. 10115,11032

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-Celo Model no. 10012,11003

Providing and fixing Body hi-Flow Single Leaver Concealed Mixer Divertor Model no. 850091

Providing and fixing Single Leaver Expose Part Kit of Hi-Flow Divertor Model no. 400024

Providing and fixing Bath Spout Model no. 400007

Providing and fixing C.P. brass Two Way bib cock of approved quality conforming to IS:8931 : Of approved quality and make as approved by engineer in charge. Model No 400003

Providing and fixing Single Lever Basin Mixer approved quality and make as approved by engineer in charge. Model No 400009

Providing and fixing 8mm dia Health Faucet with flexible tube upto 1meter long with S.S. Triangular plate to european type W.C. Of approved quality and make as approved by engineer in charge. Model No.-160160

Providing and fixing C.P. brass Overhead Shower 240X240MM Square Shape Single Flow (Body & face plate stainless Steel With chrome finish) With Rubit Cleaning system including Shower arm 600X25X25 MM Square Shape for Wall mounted Showers with Flange of approved quality Model no. 160146, Shower arm Model no. 160024

Providing and fixing Angle Cock approved quality and make as approved by engineer in charge. Model No.-400004

Providing and fixing Wall Moxer With Provision For Overhead Shower approved quality and make as approved by engineer in charge. Model No.-570020

Supply, fitting, fixing, installation and commissioning of 2.2 KW/3HP/3Ph/414V/2950RPM electric motor with pump complete set monoblock type along with base channel and civil foundation work, suction - 2.5" and delivery - 2.0" excluding delivery and suction pipe, including nut bolts, washer & required size & length of Channel to be installed at pump house for lifting water from sump to over head tank. (the cost of sanitary fittings are not included.) (Make:- Kirloskar Model NO. KDS-527- ) / Crompton / G.E.C.)

Supply, fitting, fixing, installation and commissioning of DOL starter for 3 HP motor pump of 440V to be installed at pump house including drilling holes in metal board, making connections, etc. as required, to be mouned on wall with iron strip 32mmx5mm with G.I. Nut bolts etc. as required and as per the direction of E/I.. (Make:- L&T- MK-1 / C&S/ Crompton)

Supply, fitting, fixing, installation & testing of Water storage 15 Liters Vertical Geyser of BEE 5-star rating vertical type acralic rust free body, inner container Copper, facility of temperature control ,with capillary themostat and thermal cut, ISI certified heating element along with inlet & outlet connecting pipe, fixing clamps, fasteners, 60 N/Sq.cm, closed type , As Per IS 2082: 2018 latest ( Version-2) Tank capacity-15 ltrs. etc. as required. Make:- Venus / Bajaj / Havells/Kenstar.

SITC Of 63 A/TP/10lA/'C' Series MCB

Smart Meter Panel for 4 Bedded Judge's Qrt

Supplying, designing, manufacturing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing feeders of Smart Meter Panel , unloading at site, shifting to loaction, fitting, fixing and testing of smart meter Panel, fabricated out of 2mm thick (14SWG) CRCA sheet steel for Load bearing and 1.6 mm or 16 SWG Unload Bearing, dust and vermin proof with reinforcement of suitable size iron channel, size 50mmx50mmx6mm with proper lifting arrangement, (IP-42) fully compartmentalized cubical type (folded joints construction), Floor mounted, totally enclosed, accessories, all out going feeders protection & meters as required, free floor standing , factory built sheet steel enclosed extendable panel and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 36 KA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out going feeders protection & meters as required.

The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.

The LT Panel shall be totally enclosed, completely dust and vermin proof. Synthetic rubber gaskets (neoprene/DPDM) between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be fully gasketed and shall be lockable. Doors shall have concealed hinges. All the doors shall be suitably reinforced by channel to provide rigidity. Panel shall have suitable cable entry from bottom/Top and suitable arrangement for aluminum cable termination.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Inspection of the LT Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

Location :- IN Panel Room or Near Stair.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Name of Panel Bulder:- JMD Technocraft, Tatisiway, Arnav Power Tech, Tatisilway, Meditron Bit, Meshra, STECK BIT Meshra, Ranchi. Panel Size - As per Drawing.

AL. BUS BAR

The panel includes 415V, 400A, 3Ph, 36KA, 50Hz, TPN Electrolytic Aluminium Bus Bar (E91E) GI Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. Minimum clearance between live parts / neutral to earth shall be 19mm. However clearances between terminals at components shall be as per applicable individual standard for components. Interconnections between the main bus bars and individual units shall be made using vertical / horizontal Bus Bar to individual MCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 63A 4 studs (Brass) treminal block, aluminium bus bars of adequate rating. AL. Bus Bar will be supported on insulators made of non-hygroscopic, non-inflammable material with tracking index equal to or more than that defined in BIS.

Make of Components & switch gears shall be as per approved make list

1 Set of Fabrication part of LT Panel & busbar system, with AL. bus bar and interconnection FRLS cables) in CRCA Sheet Steel enclosure (IP-42) without components. Name of Panel builders - as per approved make list.

INDICATING

1 Sets Multifunction Meter having (5010 Series) LED mete display accuracy Class 1 as per IEC 62053-21, should have an active RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Sampling rate: 64 samples per cycle.

3 Nos. CT of different power as per incomer & out going /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing.

INCOMER :-

1 No. 320A F/P MCCB (36kA) with adjustable thermomagnetc release type with S/C & O/L protection with speader link and extended front rotary handle. (Incoming cable size –1 Run 150 Sq mm 3.5 Core Al. Ar. Cable).

OUT GOING

6 Nos. 100A FP MCCB/25kA of 415V/3 Phase, 4 Wires 415V 10-60A Class 1.0 Smart energy Meter, Frequency 50Hz, Complying to IP51, with LCD Display, kWh LED, encrypted STS based token System with RS485 Modbus and polycarbonate box along with Vending/Server charges per meter per annum with 100A FP /25 kA MCCB including 70 Sq.mm. 4 studs brass terminal. (4 nnos for quarters, and 2 nos. as future use) including Single Phase 32A Automatic Change Over with provision of 10A SP MCB for each 3 phase meter in panel. (Note:- Location of all Smart kWh Meter shall be out side the Meter Panel as per the latest Guide lines of JSEB, and shall be installed in a Systematic formation with respective Quarter no. and Block No.)

1 no. 100A/FP/25kA/ MCCB Rs, 15360.00

1 no. 415V/3 Phase, 4 Wires 415V 10-60A Class 1.0 Smart energy Meter Rs, 11436.00

1 no. 70 Sq.mm. 4 studs brass terminal Rs, 250.00

Single Phase 32A Automatic Change Over with provision of 10A SP MCB for each 3phase meter in panel. Rs, 5550

Total (a+b+c+d)= Rs, 32596.00

The panel includes 415V, 100A, 3Ph, 25KA, 50Hz, TPN Electrolytic Aluminium Bus Bar (E91E). The electrolytic Aluminium bus bar as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. Minimum clearance between live parts / neutral to earth shall be 19mm. However clearances between terminals at components shall be as per applicable individual standard for components. Interconnections between the main bus bars and individual units shall be made using vertical / horizontal Bus Bar to individual MCB shall be made with 2.5 Sq mm FRLS PVC Cu.

1 no. 415V/3 Phase, 4 Wires 415V 10-60A Class 1.0 Smart energy Meter Rs, 11436.00 for Common area DB & Lift Machine.

1 No. 63 A FP MCCB with adjustable thermomagnetic release type with S/C & O/L , protection with front rotary handle and spreader links. (1 no. for Lift Machine)

1 No. 63 A 415 V TPN panel mounted, open execution type ON Load Change Over and 1 no. 63 TPN, 415V Copper Bus Bar to terminate all DG Supply connections of 4 bedded Judges quarters.

2 No. 40 A DP MCB (10kA) C series for common are DB and 1 no. Asspare

Total Cost of Components of Meter Panel for 4 BEDDEDJudge's Qurts.

MAIN LT PANEL FLOOR MOUNT FOR JUDGE'S QUARTERSG (Location in Electrical Panel Room )

Supplying, designing, manufacturing, installation, shifting to location, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing feeders of Wall/Floor Mount LT Panel, fabricated out of 2mm thick (14SWG) CRCA sheet steel, dust and vermin proof with reinforcement of suitable size iron channel, size 25mm x 25mm x 3mm with proper lifting arrangement, (IP-42) fully compartmentalized cubical type (folded joints construction), totally enclosed LT Panel and suitable for use on 415V, 3 phase, AC Supply, 4 wire, 50 C/S, system having 36 KA fault capacity, housed with incoming and outgoing aluminum bus bars, interconnection, interlocking between feeders etc. with indicating lamps, push buttons, necessary accessories, all out going feeders protection & meters as required.

The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.

Main LT Panel shall have 20% spare outgoing feeders for different rating of feeders. The Panels shall be preferably arranged in multitier formation. The size of the panel shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component do not attain temperature rise more than 40 degree Celsius.

The LT Panel shall be totally enclosed, completely dust and vermin proof. Synthetic rubber gaskets (neoprene/DPDM) between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be fully gasketed and shall be lockable. Doors shall have concealed hinges. All the doors shall be suitably reinforced by channel to provide rigidity. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cable termination.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

Location :- Location in Basement Floor Electric Room.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.-Bita Guard

Make of On Load Change Over :- L&T , Sucomo, Legrand.

Size of incoming cable:- 2R 3.5C 300 Sq.mm. Al. Ar. Cable.

Panel Size - As per approved Drawing.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

AL. BUS BAR

The panel includes 415V, 800A, 3Ph, 36KA, 50Hz, TPN Electrolytic Aluminium Bus Bar (E91E) GI Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. Minimum clearance between live parts / neutral to earth shall be 19mm. However clearances between terminals at components shall be as per applicable individual standard for components. Interconnections between the main bus bars and individual units shall be made using vertical / horizontal Bus Bar to individual MCB shall be made with 4, 6 & 10 Sq mm FRLS PVC Cu. wire with 63A 4 studs (Brass) treminal block, aluminium bus bars of adequate rating. AL. Bus Bar will be supported on insulators made of non-hygroscopic, non-inflammable material with tracking index equal to or more than that defined in BIS.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Arnav Power tech, Ranchi. TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears.

INDICATING

1 Set Multifunction Meter having (5010 Series) LED mete display accuracy Class 1 as per IEC 62053-21, should have an active RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Sampling rate: 64 samples per cycle.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing.

3 nos. CT of appropriate power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

INCOMER :-

1 No.630 A F/P MCCB (36kA) with adjustable thermomagnetc release type with S/C & O/L protection, With ON-OFF- Indication and front extended rotary Handle and spreader links in both end (Incoming cable size –2 Run 300 Sq mm 3.5 Core Al. Ar. Cable).

5 Nos. 200 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front extenbed rotary handle with spreader links. ( For 4 blocks of 3 Bedded Quarters) Cable Size 3.5 C 120 Sq.mm Al,Azr, Cable & 1 no. as spare.

2 Nos. 320 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front extenbed rotary handle with spreader links. ( For 2 blocks of 4 Bedded Quarters) Cable Size 3.5 C 185 Sq.mm Al,Azr, Cable)

2 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle with spreader links. (1 nos. for out door Feeder Pillar for external lighting & 1 no. ss spare.

Out Going Feeders With DG Set

Provision of Mechnical interlocking between 200A/FP/25KA MCCB as common incoming and 1 No. of 200A on load Change over for D.G incomer, in such a way so that the two supplies are not parallel at any time.

1 No. 200A TPN on load Manual Change over panel mounted open execution type and suitable bus arrangement for Cable termination. Make-L&T/Sucomo/ Legrand.

1 No. 200A/FP/25KA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

1 No. 160 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. ( For Fire Fighting Panel) Cable Size 3.5 C 95 Sq.mm Al,Azr, Cable)

9 Nos. 63 A FP MCCB (25KA) with thermomagnetic release type with S/C & O/L protection with front rotary handle type with spreader links. ( 1 no.for Pump Motor, 6 nos. for DG support feeders of 6 no. of Blocks of Judges Quarters & 2 nos. spare)

4 nos. 32 A DP MCB C Seires 10kA (2 nos. for Gate Light & 2 nos. as spare)

Total Cost of Main LT Panel of Campus.

Out Door External Lighting Panel (Feeder Pillar) :-

Supply, manufacturing and effecting proper connection of all incomer and outgoing, unloading at site, shifting tolocation, fitting, fixing and testing of the of out door canopy type double door Feeder Pillar fabricated out 2 mm (14 SWG) CRCA Sheet steel dust, damp, vermin and water proof (IP-55) free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted (powder coated) complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.

The LT Panel shall be totally enclosed, completely dust and vermin proof. Synthetic rubber gaskets (neoprene/DPDM) between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be fully gasketed and shall be lockable. Doors shall have concealed hinges. All the doors shall be suitably reinforced by channel to provide rigidity. Panel shall have suitable cable entry from bottom and suitable arrangement for aluminum cable termination.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet (single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the compartments as service outlet in the panel. The complete panel shall be fuse less type, for control circuits 2A SP MCB's to be used.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of each and every components and switch gears of LT Panel for approval of Consultant. Panel Builder shall visit the site before manufacturing the Panel. Inspection of the Panel shall be carried out at Panel Builder's factory by the Consultant before final delivery for that all arrangements shall be made by the contractor.

Location :- Location in Basement Floor Electric Room.

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

Make of MCCB - L&T D-Sine/ Legrand DPX³ / Schneider-NSX / Siemens - 3VL.

Make of MCB - (10kA-C-Series.) L&T U Version/ Legrand-Dx³/ Schneider-Acti / Siemens.-Bita Guard

Make of Modular Change Over :- L&T , Schneider, Legrand.

Panel Size - As per approved Drawing.

All 4 pole MCCB with thermomagnetic based release must have follwing characterstics:-

1. Icu=100% Ics.

2. With positive Isolation Marked.

3. With adjustable short circuit and over load.

4. As per IEC 60947-2.

AL. BUS BAR

The panel includes 415V, 100A, 3Ph, 36KA, 50Hz, TPN Electrolytic Aluminium Bus Bar (E91E) GI Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar as per I:S 5082 of suitable length and insulated by heat shrinkable sleeves Red, yellow, Blue and Black as R Y B & N. The current density of bus bar shall be minimum 0.8 A / sq mm. Minimum clearance between live parts / neutral to earth shall be 19mm. However clearances between terminals at components shall be as per applicable individual standard for components. Interconnections between the main bus bars and individual units shall be made using vertical / horizontal Bus Bar to individual MCB shall be made with 1.5, 2.5 Sq mm FRLS PVC Cu. wire with 63A 4 studs (Brass) treminal block, aluminium bus bars of adequate rating. AL. Bus Bar will be supported on insulators made of non-hygroscopic, non-inflammable material with tracking index equal to or more than that defined in BIS.

Bill of Material of Main LT PANEL:-

1 Set Of Fabrication part of LT Panel & busbar system, in CRCA Sheet Steel enclosure (IP-42) without any components & its busbar system, in CRCA Sheet Steel enclosure without any components. Name of Panel Builder :- JMD ELECTROTECH, KOKAR, STECT POWER INDUSTRIES, BIT, Mesra, Arnav Power Tech, Ranchi, TTS Systematix Private Ltd, Tatisiway, Meditron, Meshra, Ranchi or any approved Panel Builders of above make Switch Gears. (PART-A)

INDICATING

1 Set Multifunction Meter having (5010 Series) LED mete display accuracy Class 1 as per IEC 62053-21, should have an active RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters: Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12. Min/Max for eight parameters. Sampling rate: 64 samples per cycle.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer & outgoing.

3 nos. CT of appropriate power as per incomer /5VA -5 class one Epoxy resin cast CT (3 Nos.)=1 Set. Make:-Kappa / Matrix/Rishabh.

INCOMER :-

1 No.63A F/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L protection, and front extended rotary Handle and spreader links in both end.

OUT- GOING

4 nos. 25A/FP/25KA/ MCCB thermomagnetic release type, on of trip and S/C , O/L protection, with Rotary Handle & Spreader links.

3 nos. Power Contactor 40A NO NC of three phase of suitable rating.

3 nos. Astronomical Alpha Rex³ single channel Timer 24 hrs.

3 nos. Four pole two way Lexic changeover with centre off 440V AC 40A to be used in case of timer failure to by pass the timer.

2 nos. 63A DP MCB C Series of 10 kA

2 nos. 32A DP MCB C Series of 10 kA

Total Cost of External Feeder Pillar Panel

SOLAR ALL-IN-ONE SOLAR STREET LIGHTING with Hybrid Switch

Providing, Fitting fixing and testing of 12 V DC 30 W with hybrid Switch Smart integrated Solar All in one Street light with built in Mono Crystalline Panel, Battery- Lithium Ferro Phosphate, in built BMS, LiFePo4, with Integrated MPPT Solar Charger Controller, dimming profile and PIR Sensor with Colour temp. 6000-6500K System efficiency 125lm/W Warranty 3 Yrs against manufacturing defect with Front Cover UV stabilized Polycarbonate LED . @ L70 Battery Capacity>150 to 170Wh, Three days back up recommended pole height 4 to 5 Mtrs. pole (cost of solar street light inclusive of copper cable, UPVC pipe, burried trench etc.) As per approved make list. (Cost of Solar Street Light is exclusive of 6 mtr. poles.) . All Hybrid Solar Street Lights shall be also conncected through grid by laying 4 core 16 sq mm Al. Ar. cable.

Other Protectiion:- a. Over-Charge protection b. deep-discharge protection c. Over current protection d. Short circuit protection e. Over voltage protection

Supply and erection of 5 metre height Hot-dip galvanized octagonal solar street light pole with single arm (1000mm) with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting with MCB & connector, cement concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. (but without pole collar)

Total Cost of 12 V DC 30 W with 5 mtr hot Dip Galvanized Octagonal pole.

FOUNDATION & PLINTH OF BOLLARD LIGHT

Constructiopn of Plinth for foundation with bricks, cement plaster of Bollard light all with all other accessories like terminal box, MCB conectors etc as per drawing provided at the time of work execution or as per the direction of E/I)

1 no.construction of Plinth for foundation of Bollard Light (Earth cutting, 250mm thick brick work, PCC at bottom, cement plaster etc.

1 no. Terminal Box (Size - 6" x 6" x 4") of 2 mm CRCA sheet steel powder coating with locking arrangeme4t and rubber gasket etc.

1 no. 2A SP MCB.

2 Nos. brass/steel 4 studs 20A connector (1 No. for incomer and 2nd for outgoing cable)

Total cost of Foundation and Plinth construction for Bollard light with all above accessories.

4 METRE HEIGHT OCTAGONAL POLE

Supply and erection of 4 metre height Hot-dip galvanized octagonal street light pole with following with top dia 50 to 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of Size 220mmx220mmx 12mm thick having small door opening for junction box mounting with 6 Amp DP MCB & connector Cement concrete of 1:3:6 includuing excavation, refilling and suitable size including 4 nos. Foundation bolt of M16x450mm. Make:-VALMOUNT, TRANSRAIL,BAJAJ,/RR ISPAT..

Supplying & Laying 12mm thick chequered rubber matting of 1.1.kv 1 m wide of tested quality to with stand 15KV dielectric strenght of approved make as per IS-5424-1969.Cost of 12mm thick chequered rubber matting of 1.1.kv 1 m wide

Supplying of fire buckets of 10 liters Capacity of approved quality, painted white from inside and red outside and having inscription "FIRE" in white conforming to I.S. 2546/1974 duly amended upto date complete as required & approved by Engineer Incharge.Cost of fire buckets of 10 liters Capacity

Supplying and fixing of MS pedestal stand heavy duty with rain protection cover as required suitable for supporting three fire buckets as required for fire fighting system & approved by Engineer Incharge.Cost of MS pedestal stand heavy duty suitable for supporting Six fire buckets

Supplying and fixing carbon dioxide (CO2) type fire extinguishers conforming to IS 15683 with cylinder duly charged of capacity 4.5kgs. including fixing clamps, brackets, bolts and nuts etc. as required & approved by the Engineer Incharge. Cost of carbon dioxide (CO2) type fire extinguishers conforming to IS 15683 with cylinder

Supplying and fixing 10kg capacity Modular Automatic Fire Extinguishers dry chemical powder nitrogen type pre-set at works ranging from 57 deg C/ 68 deg C/ 79 deg C fire extinguishers conforming to IS 15683 including fixing clamps, brackets, bolts and nuts etc. complete as required & approved by the Engineer Incharge. Cost of 10kg capacity Modular Automatic Fire Extinguishers dry chemical powder nitrogen type ranging from 57 deg C/ 68 deg C/ 79 deg C fire extinguishers conforming to IS 156

Supply and fixing of shock treatment/ restoration charts written in Hindi/ local language and English duly framed and covered with 3.0 mm glass as required.Cost of shock treatment/ restoration charts

Supply of First Aid Box made of 16 SWG MS Sheet duly painted within inside and outside surfaces with one coat of primer and two coats of synthetic paint of required shade comprising the following minimum but not limited, minimum 1 No. band aid bandage 150mm, 1 No. Savlon Soap 30 ml, 1 No bottle Betadine 30 ml, 1 No Packet dressing material etc. as required, approved by Indian Red Cross / St. John's conforming to IS:2217.

Supply of 440V grade Rubber Hands Gloves. As per IS:4770- 1991.Cost of 440 Grade Rubber Hand Gloves

Supply of 1 pair 12 KV rubber hand gloves of approved make, as per IS:4770- 1991.Cost of 12 Grade Rubber Hand Gloves

Supplying & fixing of fire sealants to shafts, ceiling, cut-outs etc. with 2 hour fire rated composition as per specifications, NEC2011, relevant IS & as per approved makes of material & making good the same complete with accessories as required per site Cost of fire sealants to shafts, ceiling, cut-outs etc

Supply and fixing position the approved single line diagram framed in 1000 x 800 mm size glass frame and installed in main switch room.Cost of 1000mmX800mm Glass Frame of SLD

Providing, fitting, fixing, fabricating, erecting of MS angle of section 50 mm x 50 mm x 6 mm size for Brick wall trench to make support for MS iron plate to be fixed on every after 300 mm in RCC trench. Cost of MS angle of section 50 mm x 50 mm x 6 mm size.

Providing, fitting, fixing, fabricating, erecting of MS Plate of 2'X2 (12 mm) thick' for covering Brick wall cable trench in panel room on the support of iron angle each piece of MS plate shall be 450 mm (D) x 450 mm (W). (To cover the Brick wall cable trench in panel room.)Cost of MS Plate of 12 mm thick for covering Brick wall cable trench of size 750 mm (D) x 800 mm (W)

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Terrace Pump

Pressure Gauge Assemble with Gate/Ball Valve

Air release Valve / Drain Valve

MS Structure support for piping

Providing and fixing 25 / 15 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Add 18 % GST

Add 1% Labour Cess

ARUN KUMAR

Rhea Enterprises

Awadhesh Singh Construction Pvt Ltd

M/S MANOJ KUMAR PANDEY

Madan Lal Bajaj Construction Pvt. Ltd.