PROVN OF CERTAIN B AND R WORKS AT NAVAL TRG FACILITIES TO PROVIDE AND SUSTAIN AREA HYGIENE SANITATION AND EQPT SHIPPING IN SHIPPING OUT ROUTE AT MILIT AND SOME MINOR AND REVENUE WORKS AT MILIT GIRINAGAR PUNE 25

Amount

M & L for PCC 1:4: 8 D2 (using 40 mm graded aggregate) cement concrete in foundations, filling and mass concrete sub base, path & paving complete all as specified and as directed.

Demolition of cement conc (Un -reinforced) in ground floors and pavings n exc. 15cm thick.(Below or above ground level).complete all as specified and as directed.

M & L for cement concrete PCC type B-0, 1:2:4 (using 12.5mm graded aggregate) for floor as specified and directed.

M & L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

S&F factory made 50mm thick 600 x 600 mm manhole cover with additional frame for fixing, of precast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) finished the surface even and fair including reinforcement as per manufacturer's design and set in CM 1:4 and handles including demolition of old existing RCC cover (Reinforcement required to cut as facilitate to domolition) of any description and in any position complete all as specified and directed.

S & F for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified Add Extra for Powder Coating to Item to (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S & F for anodised aluminium door shutters,partition , aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.Add to item No for powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and as directed.

Supply and fix in repair for aluminium powder coated partition using ‘Jindal’ aluminium SP/ DP section or equivalent make as specified with 5mm thick tinted glass, PVC rubber beading,12mm thick prelaminated particle board fixed with glazing clips etc complete all as specified and as directed. Sections : SP (Single partition) - 20033, DP (Double partition) - 20034,Glazing clips - 4407 complete all as specified and as directed.

S & F for sheet glass, 5.00 mm ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane as specified and directed.

M&L for framed MS work as in doors or gates of angle or other section with gusset plates, rails braces etc, complete drilled for fixing of steel sheeting or other covering, door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings also fastening and fixing complete all as directed and complete with locking arrangement. (Fe-410 W Gde-E-250 Quality -A) complete all as specified and as directed .

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade on 15mm thick screed bed in Cement Mortar 1:4 over 25mm thick PCC 1:2:4 type B0 (using 12.50mm graded crushed stone agg ,over 75mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base or floor complete all as directed by Engr-in-Charge.complete all as specified & directed.

Excavation in trenches not exc 1.50mtr wide and not exc 1.50mtr in depth for foundation etc and getting out in soft / loose soil complete all as specified and directed.

Returning filling in, well watering ramming in layers not exceeding 15cm thick complete all as specified and directed.

Removing of excavated soil to a distance not exc 50mtrs and depositingwhere directed at a level not exc 1.50 mtrs above the starting point complete all as specified and directed by Engr-in-charge.

M & L for vitrified Ceramic colour tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15 mm screed bed or bedding layer of mortar 15 mm thick in cm 1:6 for laying floor finishes complete all as specified and as directed.

S&F Bib taps fancy type chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as dierected.

Surface excavation n.exc 30cm deep and average 15cm and getting out in soft/loose soil complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C-1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6, complete all as specified and directed.

M&L for rendering 10mm thick on cement concrete block masonry/concrete surfaces in cement mortar 1:6 finished surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for two coats of cement base paint over a coat of primer on New surfaces of wall complete all as specified and directed.

M & L for broken stone or boulders hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface as specified and directed.

M & L for Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,as specified and directed.

M & L for PCC Type B2 1:2:4 ( 40 mm graded aggregate ) as in fdn filling and mass concrete as specified and directed.

S & F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) as specified and directed.

M&L for Preparation of new steel Surfaces of any description, applying red oxide two coat of synthetic enemal paint over10cm in width orgirth,not otherwise described complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F for Pre- painted galvalume aluminium zinc coating GI based corrugated steelsheet 0.50mm thick of ancolour having tensilestrength of 550 Mpa as inroof covering/cladding towall, fixed with selftapping screws asspecified and directed.

S&F wall panelling on existing wall surface consisting 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing to be fixed on wall by self tapping screw of size 19mm x 6mm after puttin rawal plugs. The edge and periphery finally to be covered by extruded PVC corner angles beading/fillet complete all as specified and as directed by Engr-in-Charge.

S & F 5 mm thick PVC sheet fillet /beading of width 35 mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing complete all as specified and as directed.

S&F 12mm thick prelaminated particle board interior grade, conforming to IS-12823, Gde-I prelaminated both side with decorative choice lamination as in Office wall mounted shelves, cupboard shutters, Kitchen cabinets,etc fixed with GRK # 10 wood screws,2 1/2" length screw including 3mm thick, ist class HW(TW) beading all around on edging to timber frame work all as specified and directed by Engr-in-Charge.

M&L for 50mm cupboard magnet including high quality magnet and steel plate complete all as specified and directed.

S&F 30mm width of flaps (when open) in mm continous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F 150mm brass cupboard handles, cast type, polished bright fixed with nut screws and washers complete all as specified and directed.

S&F 150mm Hasp and staples safety type brass with mild steel hinge pin inlcuding bolt to hinge plate and fixed with screws of 125mm size complete all as specified and directed.

S&F of mineral fibre acoustic suspended ceiling system with prima fine fissured tile with semi concealed grid , the tile should have humidity resistance (RH) of 99% , NRC upto 0.6, light reflectance> 83%, thermal conductivity K= 0.052 to 0.057 w/m, colour white fire performance class O/class 1 (BS476 part6 &7) in module sizeof 600x 600x16 mm with Bio block coating on the face of the tile, impact resistant and suitable for green bldg application, eith recycled content of 63 %. The tile shall be laid on semi concealed grid system with 15 mm white flange incorporating 6 mm central reveal in white/black colour and with web height of 38 mm and load carring capacity of minimum 11.68 kg/sqm.Silhouette. main runner and cross tees to have mitred ends & birdmouth notches to provide mitred cruciform junction. The T sections have galvanising of 120 gms/sqm and passed through 500 hrs of salt test. all as per manufacutrer's instructions Complete all as specified and as directed. (Make : Armstrong, saint Gobain or equivalent make)

S & F air curtain machine mounted directly over any size of opening ,door & enterway create barrier of air to block dust ,insect ,debris as specified and directed.

Supply and fix for vitreous china coloured wash down water closet EWC cascade one piece type ‘P’ or S trap, in built seat cover and flushing cistern, low level, valveless, symphonic action type complete with inlet ball valve, float and handle complete all as specified and as directed by Engr - In - Charge.

S&F Vitreous china Urinal, full stall type, white with waste pipe and CP brass spreader complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified.

M & L for Precast cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed by Engineer-in-Charge.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

M&L for Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6 type C-2 for any size of drain pipe complete all as specified and as directed.

S & F for reinforced concrete pipes,bore of pipe 300 mm class NP2, laid and jointed complete with collars complete as specified and directed.

S & F for Bends, for reinforced concrete pipes laid and jointed, complete as specified and directed.

S & F for Single 'Y' for reinforced concrete pipes junctions laid and jointed, complete as specified and directed.

M & L for rendering 15mm thick in two layers, 5mm thick using WPC @3% by weight of cement over 10mm thick on cement concrete block masonry/concrete surfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement, complete all as specified incl complete removal of existing treatment all as specified and directed. Note : Water proofing compound will be paid under relevant items

Supply only WPC.

M&L for two coats of oil bound distemper over a coat of primer on New surfaces of wall complete all as specified and directed.

M & L for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) incl complete removal of exiting treatment all as specified and directed.

S&F 6 mm thick E- boarding (classic) of size 610x610 mm as in false ceiling fixed with aluminium snap and frame work of same size of aluminium Tee 25x25x1.50 mm as crosss runner and aluminium angle of size 25x25x1.25 mm at the perimeter incl GI 6 mm adjustable suspender of req length of any discription (Note: The design and specification of ceiling boards to be approved by Engr-In -Charge ) complete all as specified and directed.

M & L for Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in surface channels of manholes and fair finished using extra cement complete all as specified and directed.

M & L for type Bo 1:2:4 (12.50 mm graded aggregate ) for benching ,coping , incl weathering slightly rounded or chamfered angle as directed incl form work and finishing all exposed surface complete and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

Extra for forming fair finished drain or drain channel 30 cm inner girth in cement concrete using extra cement including forms moulds mitred stopped ends etc complete all as specified and as directed.

Dismantling floor or wall tiling incl cement mortar bedding (but not backing)removing serveaceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for double charged Ceramic Matt finish tiles 8 to 10 mm thick (square/rectangular) polished, area of each tile exc. 0.18 sqm not exceeding 0.36 sqm, in flooring etc, laid over and including screed bed of 15 mm thick cement mortar (1:4) and jointed in neat cement slurry and pointed in white or coloured cement in match dark shade complete all as specified and directed.

M&L double charged Ceramic Matt finish glazed ceramic tiles 8 to 10mm thick (square/regtangular) polished, area of each tiles exc. 0.36 sqm but not exc 0.42 sqm as in skirting/verticle surfaces etc and joined neat in cement slurry and pointed in white or colour cement to match over with and including 10mm thick rendering in CM 1:4 completeall as specified and directed.

M&L for mild steel framed work such as grill grating etc with enow of bars shouldered or rebated or forged into spike framed guard bars barred in iron doors ladders framed baluster walk say railing frame work including pintle hinges, stops, hand-made sliding bolts etc sliding channels for sliding of gate and similar work conforming to Fe 290 Gde-E-165 complete all as specified & as directed.

M&L for mild steel black sheet in door 1.60mm thick in steel gate and in similar work out to size, holes punched including round heraded screws, cut nalls or revets and flxed to wood or steel framing with plain 40 mm lap joints with revbeted or welded same including or turning up, mitred complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in plinth protection/ hardstanding// path etc complete all as specified and as directed.

G V HAGAWANE (BID ID -3125183)

M/S P D TUPE (BID ID -3102326)

Pratap enterprises (BID ID -3102564)

Mehta and Co. (BID ID -3124443)