SPL REPAIR TO DRAINAGE SYSTEM OF 12 ASSAM AND SPL REPAIR TO BLDG NO P-21A OF OLD SIGNAL CENTRE AT 7 INF BDE SIG COY INCLUDING CERTAIN MINOR WORKS UNDER AGE B/R-I AND II OF GE (I) KANPUR

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

Demolition of brickwork built in cement mortar or cement lime mortar complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) complete all as directed and specified.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as directed and specified.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exc 1.5 Sqm but n'exc 4 Sqm each complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for and all as directed by engineer in charge.

Demolition of Concrete (reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ; reinforcement cut as required to facilitate demolition)

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) unreinforced concrete & removal of rubbish beyond defence land complete all as specified and directed.

M&L for rendering 15mm thick plaster in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) with water proofing compound (WPC shall be measured and paid separately)

Supply only for Integral waterproofing compound

M&L for rendering 15mm thick Cement plaster 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement)

M&L for 10 mm thick cement plaster on ceiling in CM 1:3 finished even and smooth applying without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls including cornices plaster etc and applying two coat oil bound distemper over a coat of primer over applying a coat 1 mm of wall care putty on wall including rubbing with sand paper to achieve a smooth surface and sharp straight edges etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of cement paint over a coat of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment i.e. white wash ,colour wash ,distempering etc. of walls, cornices etc including brooming down or steel wire brushing scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spots etc and applying two coat of cement paint on wall with brush complete all as specified and as directed.

M&L for complete removal of existing treatment i.e. white wash ,colour wash ,distempering etc. of wall complete , applying a coat of wall care putty on wall including rubbing with sand paper to achieve a smooth surface and sharp straight edges etc. complete as per manufacturer's instructions and directed at site and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.all as specified and directed.

M/L for Preparation of old decorated surfaces of ceiling, cornices etc including brooming down or steel wire brushing scraping down smoke soot, moulds, moss and efflorescent and trading oil and greasy spotsetc and applying one coat of white washing on Ceiling complete all as specified and as directed.

M&L for brickwork with old brick size, subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for 7 to 8 mm thick non skid ceramic coloured tiles (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc; laid jointing in neat cement slurry and pointed in white cement mixed with pigment to match with shade of tiles over & including 15mm thick screed bed in CM(1:6) complete all as specified and directed.

M&L for glazed ceramic coloured tiles 300x450x6 to 7 mm thick on vertical surfaces such as dado set and jointed in neat cement urry and pointed in colour cement to match the shade of tile over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

S&F for Armstrong Mineral Fibre Acoustical Suspended Ceiling System with DUNE (MICRO LOOK) EDGE TILES WITH ARMSTRONG XL 15 mm EXPOSED STEEL ANGLE. The tiles should have Humidity Resistance (RH) of 99%, NRC Upto 0.5, Light Reflectance >85%, Thermal Conductivity k = 0.052- 0.057 w/m K, Colour White, Fire Performance Class 0/Class1 (BS 476 Part 6&7) in module size of 600 X 600 X 12 mm with Bio Block coating on the face of the tile, suitable for Green Building application, with Recycled content of 38-41%.The steel angle should be of “Armstrong” make with 15mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 32, 27 and 27mm and a load carrying capacity of 7.5 Kgs/Sqm. The T Sections have a Galvanizing of 90 grams per Sqm & passed through 500 hrs of Salt test ,Perimeter trim to be Armstrong wall angles of size 30x19x19mm, secured to walls at 450 mm maximum centre to centre hanging with 4 mm GI wire complete all as specified and directed according to manufacturers instruction.

Demolition by using hand held electric drills, cutting machine, chisels etc (direct use of hammers on RCC roof for demolition is strcitly prohibited) of concrete of any description including mud in roof any thickness with and including roughening old concrete surfaces by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed by the Engineer-in-charge.

Dismantling of terracing tiles/brick tiles single layer on roof complete all as specified and as directed by the Engineer-in-charge.

M&L for brick tiles 40mm thick with minimum flexural strength 1.5 N/Sqmm set, joints grouted flush in CM 1:3 mixed chemical (plasticizer) by weight of cement over 15 mm thick screed bed in CM 1:4, ponding test shall be done after laying of tiles complete all as specified and as directed by the Engineer-in-charge.

All as per item 26 but except tiles complete all as specified and as directed by the Engineer-in-charge.

M&L for Preparation of plastered roof surface by cleaning surface free from dust and other foreign materials etc. and laying in repair Atatic poly propylene polymer modified membrane pre fabricated 3mm thick with non woven polyester matt central core of 160 gms/Sqm weighing not less than 3.5kg per sqm laid over primer conforming to IS 3384 @ 0.4 lit/sqm by using LPG/Butane torch and applying uniform pressure with a roller with overlap of 100mm in longitudinal direction and 150mm in transverse direction laid as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge with and including following courses of descriptions given below :- (a) A coat of bonding material using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 Kg per Sqm. (b) Laying of APP modified membrane described hereinbefore with joints sealed with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and curved well before lying the membrane. (c) Applying binding material using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 Kg per Sqm.

S&F for MS framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required exc half brick but not exc full brick wall complete all as specified and directed.

S & F of mild steel flat iron as in hold fasts etc all as specified, confirming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F, aluminium chequered grills as on upvc windows, wight n.exc .0.50 kg / sqm and fixed all as specified and directed by Engg- in Charge.

Supply only for 4.8 mm thick Sheet glass ordinary quality.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flushbdoor shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calciumbcarbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge.

S&F in repair anodised Aluminium door partly glazed (using 5mm thick glass) and partly panelled (using 12mm thick both side prelaminated board Noavapan Kitlam) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick incl 125mm dia circular aluminium handle tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door spring of sandhu/sanant make, two numbers door stopper, hinges (three Nos each side) etc and aluminium frame of section 100x44.45x2.00mm thick complete all as specified.

S&F MS butt hinges 100mm medium weight, cold rolled, and fixed complete all as specified and directed

S&F 300mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or exruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as specified and directed

S&F aluminium anodised handle "D" type of size 150mm complete all as specified and directed

S&F 150mm long barrel tower bolt aluminium anodised of extruded section and fixed complete all as specified and directed.

M&L painting to wood and wood based surface of any description over 10cm width or girth including 2 coats of synthetic enamel paint over a coat of pink primer including preparation of newly or previously untreated surface complete all as specified and directed

M&L painting to steel and iron based surface of any description over 10cm width or girth or not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of newly or previously untreated surface complete all as specified and directed

S&F for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by engr-in-charge

M&L for providing, cement concrete type B1 (1:2:4 20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges

Material and labour for 75 mm thick plain cement concrete type C-1 1:3:6(Using 40mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed.

M & L for cement concrete Type D2 (1:4:8) 40mm graded aggregate as in foundations,filling,sub base flooring and mass concrete complete all as specified and directed.

M & L for sand filling under floor or in foundation including watering and in consolidation complete all as speified.

M & L for cement concrete Type B0 (1:2:4) using 12.50 mm aggregate as in edging portion of paver block for proper matching with existing surface complete all specified and directed.

M & L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out in mud/ sludge in fowl condition.

M&L brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 with old size brick, complete all as specified and directed.

M & L for plain Cement concrete type C-2, 1:3:6 using 40 mm graded crushed stone agg in foundations, filling and mass-concrete/bed of PCC drain as directed and specified.

M & L for Extra for forming fair finished drain or channels exc 30 cm & n.exc 70 cm inner grith in cement concrete, using extra cement incl form moulds mittred / stopped end etc complete all as specified.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of concrete or brick surface finished even and smooth without using extra cement complete all as specified and directed.

M & L for cement concrete type B-1, using 20 mm graded crushed stone agg as in benching, rounded smooth,PCC bed in drain , copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded for chamfered angles and throating, smooth fnished using extra cement incl necessary formwork as directed

Providing, precast cement concrete type B-1, 1:2:4 using 20 mm graded crushed stone agg as in landing , cover slab of man holes,drain etc,chajjass,chullah hoods,shelves and similar articles with plain face and like complete with joints to match and set with cement mortar 1:4 as specified.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Removal of excavated material not exceeding 50 mtr and depositing where directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as specified.

M&L for RCC 1:1.5:3 nominal mix (20mm graded aggregates) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc and mass concrete

M&L for RCC 1:1.5:3 nominal mix (20mm graded aggregates) as in columns, pillars, piers, posts and struts

M&L for 1:1.5:3 nominal mix (20mm graded aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span

M&L for 1:1.5:3 nominal mix (20mm graded aggregates) as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies, chhajas, canopies, deck slabs and in shelves and the like

M&L formwork to sides of concrete foundation footings, bases of columns raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work : vertical or to batter Rough finished surfaces of concrete

M&L formwork to sides of pillars, lintels, post, struts, piers, columns and stanchions for fair finished surface

M&L formwork to sides and soffits of floor or roof beams etc for fair finish surfaces

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, shelves, chajjas and similar work not exceeding 200mm thick (Horizontal or sloping)

S&F TMT bars 5mm dia and over upto 10mm dia bar as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for spreading, levelling and ramming incl watering as required in floors etc in layers n exc 25 cm thick all as specified and directed by EIC.

M&L for preparation of newly plastered surfaces of wall and applying three coat of white wash complete all as specified and directed.

S&F precast cement concrete type B0 1:2:4 (12.5 mm graded aggregate) louvres and jallies, 35 mm thick (measured solid) set in CM 1:6, including all mouldings complete all as specified and directed by Engr-in-Charge.

M & L Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling & fixing with copper screws in opening as per specification & drawing, including making good the damaged wall with plaster or concreteall as per specified and directed.

M & L factory solid panel PVC door shutter 30mm thick (style) consisting of frame made ourt of M.S. tubes for top & bottam rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with soilvent cement for stiles and plain colour PVCsheets for rail, lock rail & bottam eail on either side & asinsert for top rail & bottam rail, penelling of plain colour PVC sheet to be fitted in the M.S. frame welded /sealed/ with copper screws to the stules & rails with suitable PVC sheet beading and jointed together with solvent cement suppling & fixing in the frame at site all as specified and directed.

S&F 100mm butt hinges , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed for PVC door, type C-21

S & F Aluminium 125 mm, anodised, barrel tower bolts of extruded section and fixed

S & F 125 mm long Extruded aluminium alloy handles, fabricated type., anodised

S&F HDPE triple layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litres capacity hoisted and fixed in position all as specified in SSR Pt-I including for hoisting into position either inside or outside of building, connecting up pipes, securing access cover etc including GI nipple of suitable size, float valve, gun metal globe valve complete all as specified and directed. Make: Sintex/ Dhara/Tuff/ JS Polyplast as approved by GE(I).

M&L for cutting chases for concealed water tubing and making good in CM (1:3), cutting not exc 10 CM girth in brick wall complete all as specified and directed.

S & F GI steel tubing 15mm bore medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete as specified and directed.

S & F GI steel tubing 20mm bore medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete as specified and directed.

S&F WC squatting pan “Orissa Pattern” of size 580 x 440 mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including S&F trap set complete all as specified and directed.

S&F 10 ltrs capacity low level PVC flushing cistern, valveless, symphonic type, white,with inlet,ball float and handle including brackets complete and all as specified and directed.

S&F for vitreous china wash basin white flat back size 550x400mm but exclusive taps, wastes, chain and plug and porcelain stopper but including cutting for and pinning in ends of brackets or erecting stand, waste pipe including brackets fixed complete all as specified and directed.

S&F brass chromium plated shower rose 125 mm dia with swivel joint complete all as specified and directed.

S&F15mm bore PVC connection 600 mm long heavy duty with brass fly nut and warsher for hot and cold water complete and all as specified and directed

S & F 15mm bore stop valves,fancy type chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15mm bore PTMT bib taps any coloured, screwed down, screwed for iron pipe or for brass ferrule and fixed complete as specified and directed.(Min wt 90 gms)

S&F 15 mm dia PTMT pillar tap any colour with fly nut capstan head screwed for 15 mm dia pipe complete all as specified and directed.

S & F PTMT angular stop valves 15mm bore screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe, complete including providing and fixing plugs, beddings urinals against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; supplying fixing flushing cistern with brackets, flush pipe, waste pipe, grating and union for discharge pipe complete as specified and directed.

M&L for 75 mm PVC (SWR) nahani/floor trap, plain with grating including jointing with solvent cement all as specified and directed by EIC

M&L for 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed by EIC.

M&L for providing concrete bed to drain pipes for 150 mm dia in cement concrete 1:3:6, type C2 (using 40mm graded crushed stone aggregate) including packing under & haunching against the sides of pipes after they are laid & tested complete all as specified and directed.

M & L for reinforcement concrete pipe class NP-3 pipes of dia 150 mm with collers/ spigot/socket laid in trenches and jointed complete all as specified and directed

M&L for providing plain cement concrete 1:2:4, type B-2 (using 40 mm graded crushed stone aggregate) as in surface channels & drains complete all as specified & directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitered/ stopped ends etc complete all as specified and directed.(NOTE: Inner girth shall be measured)

M&L for Plain cement concrete (1:2:4) type B-0, using 12.50 mm graded crushed stone aggregate as in roof kerbs or mud stops benching of manholes coping, bands, plinth course and other similar works etc rounded or chamfered on edges including necessary form work complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone agg for concrete bed to drain pipe incl packing under and haunching against the sides after they are laid and tested for 150mm bore RCC NP-2 pipe complete all as specified and as directed.

S&F 150 mm bore RCC hume pipe class NP-2 laid in trenches and jointed in CM 1:1 complete all as specified and as directed.

M&L Brick work with burnt clay subclass “B” brick straight or curved on plan exceeding 6 mtr mean radius built in cement mortar 1:4 comlete all as specified and as directed.

M&L for TMT 6 to 8mm dia, cut to length bent to shape required including binding with MS wire (annealed) not less than 0.9mm dia all as specified

M& L soakage wells 3 M dia X 4.5 M effective depth with specification excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size.

Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

M&L hardcore of broken stone or boulder of gauge n exc 63 mm , deposited spreaded , levelled in layers n exc 15 cm thick watered and rammed to true surface all as specified.

M&L 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in as in sub base all as specified and directed.

Providing precast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in cement mortar complete (1:4) with joints to match ®

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 typeB-l smooth finished, and reforming benching as required for 150 mm internal bore pipe all as specified and directed by EIC.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified.

Point wiring for one light point/bell point controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size not less than 20mm dia with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size & as directed by Engr in Charge & 3 mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and directed.

All as per srl item No-111 here in above but for one 3 pin 15 Amps socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl conduit.

All as per srl item No-111 here in above but for one 3 pin 5A socket outlet independent controlled by one switch.

All as per srl item No-111 here in above but for one 5A socket outlet on the same board controlled by one switch.

M&L for switch piano flush button single pole one way 5/6 amps 240 volts.

Switch piano flush button single pole one way 15/16 amps 230 Volts.

M&L for socket 5 amps 5 pin flush type, 230 volts.

M&L for socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts.

M&L for ceiling rose surface bakelite 3 terminals.

S & F of lamp holder insulated body with back plate suitable for batten / conduit fitting complete all as specified and directed.

M&L in replacement for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLSH) of size 4 sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 2.5 Sqmm as earth lead in & including concealed PVC conduit medium grade 25mm dia cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification all as required at site or directed. Make of Cable : L&T, Havells, Polycab and Make of Conduit : Havells/Kamplast/Polycab

S&F in replacement of wall mounted LED light fittings 20 watt, 6500K, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver complete connecting electrically all as directed. Make : Wipro/Havells/Phillips/Bajaj

Supply and fix in replacement of High power LED street light 25 Watt IP 66 Energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source and electronic driver incl suitable size service bracket fixed with clamps, nut, bolt and washer and electric connection with 1.5 Sqmm multistranded twin core alum cable PVC insulated complete all as spfd.

Supply and fix sheet metal enclosure MCB distribution board, double door with IP-43 IK-09 protection with metal door single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .

M&L for MCB single pole 240 volts 5 to 30 amps, with rupturing capacity 10 KA using thimbles of required size. Make: Legrand/Havells/ABB/L&T

M&L MCB single pole & neutral 240 volts 30 to 63 amps,with rupturing capacity 10 KA using thimbles of required size. Make: Legrand/Havells/ABB/L&T

Supply & fix Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting.

M&L for Earthing complete with galvanised cast iron earth plate electrode of size 600x600x6mm thick as earth electrode with top edge of the earth plate not less than 1.5mtr below ground level using GI wire 4mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of charcoal dust and salt all around the erth plate, earth work in any type of soil remaing surplus excavated material all as required at site and specified in EP No 5 of SSR part I 1991 or directed by Engineer-in-charge and testing on completion.

Excavation in trenches/foundation in soft/loose soil not exc. 1.5 metre wide and n'exc. 1.5 m deep for T/LT underground cable/pole foundation and getting out including forming bottom surface to required level or shop, complete all as specified and directed by Engineer-in-Charge.

Returning, filling of excavated soil after laying the cable with spreading levelling watering and well ramming inlayers not exceeding 25 cm thick in loose/soft soil complete all as spcified and directed.

Removal of surplus soil/excaated material obtained from grond level to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above from the starting point complete all as spcified and dircted.

M&L for sand cushning to U/G cable in layes of 23cm thick (8cm before laying the cable and 15 cm thick after laying the cable) in trenches including watering and consolidation, complete all as specified and directed. Note: Only punned thickness 18 cm shall be measured and paid.

Supplying and laying sub class b brick old size, size 230mm x 115mm x 75mm complete all as specified and directed.

Supply and laying in trenches or fixing to wall/pole or passing through pipe XLPE insulated heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 10 sqmm 2 core.

JOG CONSTRUCTION

M/S AADI ENTERPRISES

Khushi Muskan Engineer & Developer

M/S SDS Construction Co.

murty construction company