8390PROVN OF IRON LID ON TUBE WELL INSIDE CAMPUS AIPT UNDER CE (CENTRAL) PUNE

Amount

Surface excavation not exc 30cm deep and an averaging 15cm deep and getting out in soft / loose soil all as directed.

Demolition of brick work or stone / boulder masonry built in cement mortar in any position including all quoins, arches & pillars etc. complete all as directed and specified.

Removing excavated material (Soil) to a distance not exc 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point all as specified & directed.

M & L for PCC type D2, 1:4:8 (using 40mm graded aggregates) as in Foundation , filling & Mass complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregates) finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified.

M & L for RCC (Nominal Mix) type B1, 1:1½ :3 (using 20mm graded aggregates) as in Foundation including raft, footings, foundation beam, plinth beams, bases of columns, basement slabs, mass concrete etc complete all as specified and as directed.

Use and waste of form work to sides of concrete foundation , footings, bases of columns, sides and soffits of plinth beams and similar works vertical or batter rough finished surfaces of concrete curved all as specified and as directed..

M & L for TMT bars 10mm dia and over cut to length bent to shape required incl, cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to IS:1786 complete all as specified and as directed

All as per item No 08 above but 5mm dia and over upto and including 10mm dia as in stirrups , sapcers and binders.

S & F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, door chowkats of angle or other section and similar works complete of Gde Fe-290 Gde E-165 including welding etc.

M & L preparation of new or previously untreated surfaces of steel of any description over 10cm width or girth not otherwise described over applying two coats of synthetic enamel paint over a coat of a red oxide zinc primer all as specified. .

M & L for 75mm thick cement concrete type D-2 1:4:8 using 40mm graded stone aggregate as in sub base / flooring complete all as specified and as directed.

M & L for rubber moulded glossy chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M & L for precast concrete solid block masonry exc 10cm width with solid block of PCC (1:5:8) Gde D-5 and setting in CM 1:6 complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces of wall by brooming / wire brushing / removal of loose scales / dusts / unwanted particles and applying two coat of cement based paint complete all as directed and specified.

M & L for rendering 15mm thick in CM (1:4) on brick / concrete surfaces finished even & smooth without using extra cement complete all as specified and directed .

M & L Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as directed and specified.

M & L 1.25mm thick plain black sheets in wall cladding , steel gates , and similar works cut to sizes, holes punched including round head screws, clout nails or rivets and fixed to wood or steel farming with plain 40mm lap joints with riveted or welded seams including bending or turning up , mitred angles etc as required all as directed and specified.

ANIL CONSTRUCTION CO.

S V ENTERPRISES

Agarwal Agencies