REPAIR/ MAINTENANCE TO HARD STANDING, FLOORING, ROOF, JOINERIES AND PERIODICAL WORKS AT OFFRS MD ACCN AREA, ZONE B AND REPAIR / MAINT AND IMPROVEMENT TO CERTAIN B/R ASSETS AT E/M INSTALLATIONS AND ALLIED WORKS UNDER GE (EAST ) MATHURA

Amount

Demolition of roof treatment including PCC/ Brick Tiles, Mud phuska PCC padding, plastering, APP membrane complete treatment of any thicknesss and in any position and removing the demolished material out of MoD land complete all as specified and as directed.

M&L for 40 mm average thick PCC 1:2:4 type B0 (using 12.5 mm grd stone agg) in floors/ roof padding finishing the surface even and smooth with out using extra cement complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L, APP based polymeric membrane minimum weighing 3kg/ sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

M &L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; cut and polished over and including 20 mm screed bedding layer in CM 1:6 set jointed and pointed with premium cementious grout of JK or its equivalant complete all as specified and directed.

Removal of plants with roots from roof/ wall/ shafts at any height and applying HCL chemical and filling hole with PCC 1:2:4 minimum 0.05 cum in each location and finished properly with matching to the exist sarounding area complete all as specified and directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each complete all as specified and as directed.

Taking down Chowkhats or frames with shutters (without taking down shutters from frames) area exc 1.5 sq. m but n exc 4 sq. m each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1.0sqm not exceeding 2.0 sqm each complete all as specified and as directed.

Taking down of old aluminium shutter of any description exc 1.50 Sqm n exc 4 Sqm each and re-securing after repair locking arrangement, floor spring, adjusting bottom and top pivot complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F 35 mm thick factory made flush shutters, solid core construction with block board core and plywood face panel veneer type on both side complete all as specified and as directed.

S&F 35mm thick factory made IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters complete all as specified and directed.

S&F Pressed steel frame for doors of size 125 X 60mm frabicated out & 1.25mm thick sheet with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, supplied and fixed complete all as specified and as directed.

S&F Pressed steel frame for doors of size 105 X 60mm fabricated out & 1.25mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, supplied and fixed complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F Aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

M&L Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and as directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370). Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B.

S&F in repair 1mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, an?choring rod, hasp and staple and one shop coat of primer; erected in position as indi?cated, complete: push pull or manual type complete all as specified and directed.

S&F in repair, Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F in repair, Ball bearing for rolling shutters complete all as specified and directed.

S&F aluminium anodised barrel tower bolts 200 mm long of extruded section and fixed complete all as specified and as directed.

S&F 150 mm Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250mm long of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F extruded aluminium handles of size 150mm long fabricated type anodised complete all as specified and as directed.

S&F 75mm aluminium barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and complete all as specified and directed.

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F in repair 75mm long stainless steel mild steel Butt hinges, medium weight, cold rolled complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue anodised overall length of cover plate 150mm with hard drawn steel spring, fixed in floor complete all as specfied and as directed.

S&F steel window with side hung shutters including projecting type hinges with steel handle, and steel peg stay complete with glazing bars complete all as specified and as directed.

S&F steel window with side hung double shutters including projecting type hinges with steel handle, and steel peg stay complete without glazing bars complete all as specified and as directed.

M&L for repairing steel windows and ventilators hinges, brackets, steel handle, etc by spot welding at site complete all as specified and as directed.

S&F in repair 100 mm size mortice lock of brass, vertical type, 4 levers, complete all as specified and as directed.

S&F in repairs 25 mm dia stainless steel alloy tubular curtain rod cut to size and fixed in position including fixing brackets, stops, rollers end caps etc. complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty/wooden/rubber beading in Sqm n.exc 0.50 Sqm in each pane complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty/wooden/rubber beading in Sqm exc 0.50 Sqm in each pane complete all as specified and as directed.

S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F 5 mm thick sheet glass ordinary quality and glazing with aluminium beading n exc 0.50 Sqm in each pane complete all as specidfied and as directed.

S&F 5.5mm thick sheet glass ordinary quality and glazing with aluminium beading exc 0.50 Sqm in each pane complete all as specidfied and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish off the premises complete all as specified and directed.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work (reinforecement cut as required to facilitate demolition) complete all as specified and as directed.

M&L for 50 mm thick PCC type C1, 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC type B1, 1:2:4 (using 20 mm graded stone aggregate) finished surface even and fair with using extra cement, laid in alternate bays & joints filled with bitumen and sand mixed in 1:3 complete all as specified and directed.

M&L PCC 100mm thick, 1:4:8 (Type D2) using 40mm graded crushed stone aggregate as in sub base complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) louvers and jallies 40mm thick including all mouldings set in CM 1:4 complete all as specified and directed.

M&L for PCC type B1 1:2:4 (using 20mm graded stone aggragate) as in coping surface channels, benchings etc of manholes finished fair and even complete all as specified and directed.

M&L cement concrete type C-0 1:3:6 (using 12.50mm graded stone aggregate) as in bed blocks for fixing hold fasts and fillling of back of pressed steel frame etc. complete all as specified and as directed.

M&L for Chequered cement concrete tiles (with white cement and pigment) 30cm x 30cm x 25mm thick rubber moulded glossey finish, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bedding in cement mortar 1:4 complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade made with grey cement and pigment complete all as specified and directed.

M&L for sand filling under floors incl consolidation etc complete for laying paver blocks complete all as specified and directed.

Dismantling floor hearth and wall tiling including cement mortar bedding (but not backing) and rubbish off the premishes complete all as specified and as directed.

Dismantling of stone slab of any description of thickness in floors & aprons etc, laid bedded and pointed in any mortar complete all as specified and directed.

M&L 25 mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate as in levelling course for flooring complete all as specified and directed.

M&L for coloured Non Skid ceramic joint free tiles 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including and over 15 mm thick screed bed in C: M (1 : 4 ) complete all as specified and directed.

M&L non skid cermic ENDURA coloured tiles 7-8mm thick (square/rectangular) area of each exc 0.06 Sqm but n. exc. 0.11 Sqm as in floors set and jointed in neat cement slurry & pointed with coloured cement to match the colour of tiles laid over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for Coloured Glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10mm thick plaster in cement mortar (1:3) complete all as specified and as directed.

M&L for coloured Vitrified Ceramic tiles 10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in C:M (1:4) complete all as specified and as directed.

All as per item No. 63 above but as in skirting/ dado over and including 10 mm thick rendering in CM 1:3.

M&L for 20mm thick granite of (any type) work (table rubbed and polished) in steps jambs,window cills, cooking platform pillars and like in cement mortar (1:4) screed bed of mortar 20mm thick for laying floor pointing inwhite cement (1:2) using marbal dust with admixture of pigment to match the colour including rounded/ half rounded edge and hole for gas pipe in pre-cast slab complete all as specified and as directed..

M&L Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointd with pigment to match the shade of the slab including rubbing and polishing including screed bed and bedding layer of mortar 15 mm thick for laying floor finishes use CM 1:3 size complete all as specified and as directed.

M&L kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item above including 10 mm thick cement plaster use CM 1:3 complete all as specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

M&L for Precast cement concrete factory made road side kerbs block of mix 1:3:6 type C-1 (using 20 mm graded stone aggregate) n exc 100 mm in width and jointed in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on brick or stone walls,ceiling etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4) on other than fair faces of brick/ concrete surfaces finished the surface even and smooth without using extra cement, using 200 ml water proofing liquid per bag of 50 Kgs cement complete all as specified and directed. Note: Qty for water proofing chemical will be measured saperately.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faces of brick/ concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar (1:4) on fair faces of brick/ concrete surfaces finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10 mm thick on ceiling surfaces in CM 1:3 finished surface even & fair without using extra cement complete all as specified and directed.

Supply only Liquid water proofing compound of complete all as specified and directed.

M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/ Kg of mix per coat. Second coat should be applied after 4-6 hrs of first coat, 5 days curing is to be carried out to the surface before providing plastering complete all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for Brickwork with fly ash bricks (old size) straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

Dismantling of 6 mm thick AC corrugated or semi-corrugated sheets in roof covering including ridges, hips, valleys and flashings etc . complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of on colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Asbestos cement one piece plain angular 6mm thick as in ridge/valley gutters fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position in unframed work complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F welded steel wire fabric of weight n exc 4 kg per Square metre supplied and fixed complete to wood or steel members complete all as specified and as directed.

M&L for Mild steel work in tubular trusses purlins, including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and directed.

S&F rolled mild steel joist, channel, angle or Tee section fixed independently without connecting plate etc cut to ordinary length i.e. within 20 mm of length indicated) of Fe 410 Gde E-250 quality complete all as specified and directed.

S&F MS flat iron wind ties for roof including all necessary drilling, bolting or riveting etc complete all as specified and as directed.

S&F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with & including either hooks, hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) hanging also fastening and fixing complete of FE 410-W (Gde-E-250) qualit A complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings framework of water tanks and similar work conforming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F rolled mild steel in joist, channel, angle or Tee section fixed independently without connecting plate etc cut to ordinary length i.e. within 20 mm of length indicated) of Fe 410 W Gde E-250 quality 'B' complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any type and any thickness including cover fillets complete all as specified and as directed.

M&L for providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint for all hights complete all as specified and as directed.

M&L for 4 mm thick non-asbestos fibre cement building board fixed to aluminium grid with screw complete all as specified and as directed.

S&F solid PVC Wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and as directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame complete all as specified and directed.

Taking down aluminium door shutter any size dismantiling stiles and rails refixing the same using same materials including glass sheet and partical board sheet with replacement of 6mm dia GI full screw to full width of shutter bolts 2 Nos one at each top and bottom with necessary cleats using screws and nuts etc. complete all as specified and as directed.

Taking up or down steel tubing and connections ,15 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections , 20 mm bore complete all as specified and directed.

M&L 15 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L 20 mm nominal bore Mild steel galvanised water tubing , medium grade , with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 25 mm bore steel water tubing, medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floor including taking down complete all as specified and as directed.

S&F in repair 20 mm bore GI Union complete all as specified and as directed.

S&F in repair 20 mm bore GI Elbow complete all as specified and as directed.

S&F in repair 20 mm bore 6 inch long Nipple complete all as specified and directed.

S&F in repair 20 mm bore 4 inch long Nipple all as specified and as directed.

S&F in repair 20 mm bore GI socket complete all as specified and as directed.

S&F in repair 15 mm bore GI Tee complete all as specified and as directed.

S&F in repair 15 mm bore GI Union complete all as specified and as directed.

S&F in repair 15 mm bore GI Elbow complete all as specified and as directed.

S&F in repair 15 mm bore GI socket complete all as specified and as directed.

S&F in repair 15 mm bore 125 mm long Nipple complete all as specified and directed.

S&F in repair 15 mm bore 100 mm long Nipple complete all as specified and directed.

S&F in repairs vitrreous china wash hand basin, white, flat back, size 550x400mm including brackets and a pair of rack bolts, waste fittings, brass, chromium plated 32mm with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed,PVC waste pipe of 32mm bore 75cm long, complete all as specified and as directed.

S&F in repair wash down water closet pan (Pedestal Pattern) complete (exlcuding flushing cistern and flush pipe) pedestal pan and trap including plastic water closet seat cover white, closed pattern with flat bottom, and cover and mild steel hinge chromium plated including connection to drain (or outgoing pipe) and flushing pipe, antisyphonage pipe etc, complete all as specified and as directed.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including provision of lime concrete bed and 10 ltr capacity PVC valveless syphonic action type low level flushing cistern white, with inlet, ball valve, float, handle and 32mm dia PVC flush pipe complete all as specified and as directed.

S&F in repair PVC valveless syphonic action type flushing cistern Low level of 10 litre capacity, white with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed.

S&F in repair SS Hand jet health faucet 15 mm bore with 8mm dia and 1.2 m long flexible SS tube and wall hook and connected fittings completed all as specified and as directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete as specified and as directed.

S&F in repair bib taps cast copper alloy chromium plated fency type with crutch or butterfly handle, screwed down screwed for 15mm bore dia iron pipe complete all as specified and as directed.

S&F in repair angular cock cast copper alloy chromium pated fency type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15mm bore dia iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs wall mixer 15 mm bore cast copper alloy chromium plated with connector, including hand and head shower arrangement with connecting legs, wall flanges and wall bracket for hand shower complete all as specified and as directed.

S&F in repair Basin Mixer cast copper alloy chromium plated 15mm bore dia without popup waste system with 450 mm long Braided Hoses complete all as specified and as directed.

S&F in repair pillar taps, cast copper allloy, chromium plated with capston heads, chromium plated, screwed down high pressure, with or without letter hot or cold with long screwed shank and fly nuts, screwed fo iron pipe 15mm bore dia of pipe complete all as specified and as directed.

S&f in repair two way bib cock cast copper alloy chromium plated superior quality with wall flange fixing to 15 mm bore dia pipe complete all as specified and as directed.

S&F in repair stop valve cast copper alloy chromium plated fancy type, chromium plated with long sank and cup (concealed type) screwed down high pressure with crutch or butterfly handle scrwed both ends for 15mm dia bore iron pipe or union complete as specified and as directed.

S&F in repair stop cock/ value cast copper alloy screwed down with high pressure with crutch or butterfly handle screwed with ends for iron pipe or uinon & fixed of 15 mm dia complete all as specified and directed.

S&F in repair bib taps chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe of bore 15mm complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F in repair chromium plated Towel Rail 600 mm long complete all as specified and as directed. Make : Jaquar/Kohler/Grohe.

S&F in repair waste coupling of PTMT for 32mm bore discharge pipe (half or full threaded) (minimum weight 45gms) complete as specified and as directed.

S&F Grating doom 100mm dia with hole of PTMT (Minimum weight 25gms) complete all as specified and as directed.

Supply and fix in repair rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) 1000 liters capacity white colour triple layer, hoisted and fixed on roof in position including all connections complete all as specified and as directed.

S&F in repair rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) 500 liters capacity white colour triple layer, hoisted and fixed on roof in position including all connections complete all as specified and as directed.

S&F in repairs cover for HDPE water tank of capacity 500/1000 ltrs rotating type with frame including nut bolt complete all as specified and directed.

S&F Ball brass valve high pressure with polythene float and fly nuts complete screwed for 20 mm bore dia iron pipes or brass ferrule and fixed complete all as specified and as directed.

S&F in repair Ball brass valve high pressure with polythene float and fly nuts complete screwed for 20 mm bore dia iron pipes or brass ferrule and fixed complete all as specified and as directed.

S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for 15 mm bore dia of pipe and fixed ( Minimum weight 210 gms each) complete all as specified and directed.

S&F in repair gun matel, globe or gate valves 20 mm bore dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair 100mm cast iron sanitary connection 'S' branch with branch 370 to 450mm long excluding joint complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls incl necessary clamps etc incl dismantling old pipes complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls incl necessary clamps etc incl dismantling old pipes complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) bends any radius with oval access door complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

M&L for preparation of newly plastered surface of ceilling and applying three coats of white wash on ceiling surface complete all as specified and directed .

M&L for preparation of new plastered surface of walls and applying two coats of oil bound distemper over a coat of Alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over and including a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of old plastered surfaces of wall and applying one coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for chipping of unsound/deteriorated cement concrete up to 50mm average thickness from slabs, beams, columns, chhajjas etc with manual chisel including tempering of all edges including cleaning of exposed concrete surfaces and reinforcement with wire brushes etc and disposal of debris complete all as specified and as directed.

M&L for Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slabs/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 40 mm average depth including saw-cutting of all edges making square shoulders of the cavities all as specified and as directed. Note :- (i) All loose unsound and cracked concrete shall be removed out side MD land. (ii) Thickness will be measured excluding plaster

M&L for providing mixing and applying over reinforcement bars zinc antirust agent as per specification of make 'Fosroc Nitozinc Primer STD base' or equivalent in SIKA/Thermax/FOSROC complete all as specified and as directed.

Mixing and applying SBR latex modified cement mortar 25 mm thick in cement sand mortar in proportions of 1:3 (1 cement and 2 graded quartz aggregate) with polymer admixed in proportions as approved, including trowelling with wooden tools on prepared concrete surfaces of parent material complete all as specified and as directed. Note :- Acrylic polymer will be paid for separately.

Supply only approved SBR latex from FOSROC/BASF/DR FIXIT/ SIKA for bonding coat/Polymer modified cement mortor complete all as specified and as directed. Note: Rate shall be in terms of solid contents of polymer.

M&L for preparation of newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exterior paint dark shade over a coat of primer (100% Acrylic) using spray machine, spray hard to receive area to achieve excellent application using limited manpower including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&l for preparation of old surfaces of walls and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for Providing 1 mm thick wall care putty on surfaces of wall complete all as specified and as directed.

M&L for preparation of old decorative surfaces of walls and applying one coat of oil bound distemper complete all as specified and as directed.

M&L for complete removal of existing treatment from old plastered surfaces and applying two coats of distemper oil emulsion, white or tinted complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls/ ceilings and applying one coats of weather proof acrylic exterior paint including required scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for complete removal of existing treatment from old plastered surfaces of walls and applying two coats of cement base paint including required scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted steel surface of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for preparation of old painted Concrete surface of any descriptionnot otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for one coat of french polishing on old surfaces of any description, width or girth including cleaning, and preparing the surface complete all as specified and as directed.

M&L Obliterating old writing of any description with synthetic enamel paint n.exc 0.10 sqm each to match the existing work complete all as specified and as directed.

M&L for Writing letters or figures (Block, Roman, Italic or Indian) n.exc 30 Cm high complete all as specified and as directed.

M&L for Preparation of old plastered or un plastered distempered surfaces of walls by washing, rubbing down, stopping of distempered or painted surfaces, removing nails and applying one coat of oil bound distemper on wall surfaces complete all as specified and directed.

M&L preparation of new plastered surfaces of walls, providing 1mm thick wall care putty to achieve smooth surface and applying two coats of distemper oil emulsion over and including a coat of alkali resistant primer complete all as specified and as directed.

M&L for repairing the edge/corner of chajja/roof projection, ceiling and similar work by removing plaster width/girth exc 200 mm but not exceeding 300 mm and making good with plaster in two coat, comprising 10 mm thick dubbing coat in cement mortar 1:3 and finishing coat 10 mm thick in cement mortar 1:3, including providing chicken mesh wire netting 25, gauge, 20 mm mesh, between dubbing coat & finishing coat, match with existing surface complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls/ceilings and applying one coats of weather proof acrylic exterior paint (100% Acrylic) with spra machine, spray hard to reached area to achieve excellent application using limited manpower, including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed. Note : (i) WPC exterior paint shall be applied machincally by latest machine such as trucare Graco or equivalent having minimum pursue of 3300PSI. (ii) The work shall be got execute through approved applicater of paint manufactures.

Preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic paint over and including one coat of red oxide primer complete all as specified and directed.

M&L for preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat pink primer complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

Supply only chain link mild steel galvanized fencing any size or type complete all as specified and directed.

Fixing only chain link fencing of description fixed to steel part with mild steel flat & nut bolt etc. complete all as specified and directed. (a) Supply only fencing will be measured and paid separately. (b) Supply & fix mild steel nut bolt line wire and flat will be measured and paid separately.

Supply and fix mild steel section for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts for post and struts for fencing including cutting top to shape as directed drilling hole notching for wire etc.or flat iron fillet (for securing wire mesh etc)including all necessary drilling bolting,using steel section of grade E-165 ( Fe-290) complete all as specified and directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long & dia of shank 5 mm to 10mm long complete all as specified and directed.

M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed fixed in repair complete all as specified and directed. Note :- Each line wire shall be measured

A N BUILDERS

AHMED CONSTRUCTIONS

M/S SHRI RAM INFRASTRUCTURE

Bidder Name

A N BUILDERS