Creating additional fecilities and Skill training center at Valikandapuram pt

Amount

1. CREATING ADDITIONAL FACILITIES SKILL TRAINING CENTER @ VALIKANDAPURAM H/O VALIKANDAPURAM PANCHAYAT. Brick work using country bricks of size 83/4"x41/4"x23/4" in cement mortar 1:5 (One cement and five M.Sand) including curing neat finishing, etc., complete

Plastering with Cement Mortar 1:5 (One cement and Five P.Sand), 12mm thick in all floors including curing etc. complete

Dismantling the damaged pressed tiles including removing away from the site including all labour charges etc complete.

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone M.Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification

Supply and fixing in position of Roof Truss arrangements etc., Complete. Supplying and fixing in position of following size Rafter and purlin etc complete Purlin Hollow section.Vertical column

Base plate (including Bolt & Nut)

Truss

Purlin

Roofing with roof ridge sheet standard accessories Colour coated A1 Zn alloy coated steel (550 Mps) 0.50 mm TCT Conveyance loading, unloading best quality using J or U clamps with bitumen washers etc., complete as per standard specfication., etc., complete.

Supplying, fabricating and fixing in position of Aluminium Natural Colour Mat finilsh Fixed Glazing with Aluminium grill of 10mm thick the glass used shall be of 5 mm thickness. The Aluminium Section are to be anodised under electrically controlled condition as per IS 1868/1962 for an anodic film thickness of 15 microns.complete complying with standard specification and as directed by the deparmental officers. All the materials should be got approved by got approved by the Executive Engineer before execution of works.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/ m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Supplying, Fabricating, erecting and fixing Hilux (or) equivalent Gyp Board FALSE CELING upto a ceiling height of 4.50 m from floor level using Hilux board Plain sheet 10mm thick which includes shaped GI channels of size 25 x 25 x 0.50 mm thick suspended from ceilling at 1.2 m both longitudinal and cross vertical support and fixing shaped GI channels of size 50 x 30 x 0.50 mm and 150 x 10 x 0.50 mm thick at 0.60m centre longitudinal and cross direction for vertical supports and fixing U shaped GI channels of size 50 x 30 x 0.50 mm thick and 50 x 10 x 0.50 mm thick at 0.60 m centre to centre in cross direction and respectively for horizantal supports of zig - zag pattern and fixing of Gyp board in the panel provided in the desing pattern given and sprating the standard specification and as directed by the departmental officers. The rate shall be inclusive of finishing the edges and wall junctions with suitable lipping and cornice arrangements.

Provision for following Electrical arrangements Light and Fan Point

5Pin Plug Point

LED Light

Ceiling Fan

Supply and fixing of MS Ladder with hand rails and landing including cost and conveyance of all labour charges etc complete.

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

DHARMARAJ G (BID ID -1535065)