Construction of Patient Waiting area for RRU Building at ACTREC

Amount

PLUMBING WORK

SANITARY FIXTURES & FITTINGS:

Providing and fixing European type white glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the outside face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps ,20 mm dia.UPVC overflow pipe ,mosquito proof couplings G.I. chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete.(prior approval of sample and brand by Ex. Engineer is necessary before use)

Providing and fixing wall hung white wash basin of size 550 x 400 x 195 mm with pillar cock having flow rate up to 6.0 Litr/Minute,C.P.Angular stop cock long thread of Jaquar/Cera/Hindware /Perryware or equivalent make, including SS bottle trap of approved make etc complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing over the counter white wash basin with pillar cock having flow rate up to 6.0 Litr/Minute, C.P.Angular stop cock long thread of Jaquar/Cera/Hindware/Perryware or equivalent make, including SS bottle trap of approved make etc complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing white glazed urinal with Pressmatic auto closing valve having flow rate up to 4.0 Litr/Minute of Jaquar/Cera/Hindware /Perryware or equivalent make with SS bottle trap with fitting arrangement etc.complete as directed by Engineer in charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

C.P. FIXTURES FITTING WORK

Providing and fixing C.P. BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete.

Providing and fixing 15 mm diameter CP type of approved make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete

Providing and fixing C.P. Angular stop clock with wall flange Jaquar make or equivalent continental ( for geyser including necessary sockets/union nut etc. complete.

INTERNAL WATER SUPPLY

Providing and fixing concelaed in wall faces including labour following sizes of pipes CVPC SDR 11 with Cement solvent joints with supply of necessary Cpvc specials etc. (specials like sockets, union nut, elbows, bends, reducers, plugs hold tite and T’s etc. complete ) including supply of cement solvent joint for water-tight joints including hydraulic testing as per ISS including making holes, grooving in walls & roof with cutter machine & making good the damages by bringing them to good original condition & complete in all respects as directed by the Architect including etc complete. (INTERNAL TOILET DOMESTIC & FLUSHING LINE)

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing Brass/Bronze/S.S. Ball valve with pressure rating of approved make with material and labour etc all complete as per drawings, specifications and directions of the engineer-in-charge.

Providing and fixing single acting air release valves with screwed inlet 25mm dia as per I.S 12992 rated for 20Kg /cm Sq .and dia to be fitted on water supply riser with male adapter

Providing, fixing, testing & commissioning of heavy quality gun metal or brass PRV's of approved makes in water supply drop pipes including necessary fittings & supports, guages etc. complete by the site engineer & to be installed inside shaft, online type

25mm dia

32mm dia

50mm dia

Providing and fixing Digital Water Flow Meter (16 bar) complete with digital display LCD, wires, flanges, gaskets, bolts and nuts all according to technical specifications, drawings and engineer’s directions.

Supplying and erecting 0-100 lb/sq.inch pressure gauge having 4" dia. 16-6-31 Supplying and erecting 0-100 lb/sq.inch pressure gauge having 4" dia.

16-6-35 Providing and fixing 45cm wide mild steel ladder of 40mm x 6mm mild steel flat stringers and steps of 18mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti-corrosive paint)

INTERNAL TOILET SOIL/ WASTE

Supply,installation , testing commissioning of Indian UPVC pipes, SWR Type -B as per IS 13592 for 75 mm and above, UPVC Class-3 as per IS 4985 for pipes Below 75 mm with solvent cement joints & making proper connections to equipments including all necessary fittings and specials such as bends, tees, reducers,nuts,bolts, gasket, plug, supports etc. Fixing at wall/ ceiling level supported by clamps, Y branches, Rodding Eye etc. as per the specification,drawings and schematics. All hangers, clamps, brackets, anchor/fixed support, guides, rollers etc. shall be of galvanized iron unless specified otherwise and then supply and installation of the same shall also be included for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted. All Y branches and 90 deg bends should be with door bends. - (sizes mentioned are Nominal OD with accepted tolerance of + 0.3 till 100 mm and 0.6 upto 200 mm)

Providing, fixing, jointing, tetsing & commissioning of Floor PVC cleanout plug with suitable inlet keys for opening, male threaded joint with Socket caulked to soil or waste pipe as required

75 mm dia

110 mm dia

Providing and fixing Multi floor trap of 110x110mm with jali 50 mm minimum seal suitable for kitchen all complete.

Providing and fixing P-trap of 110x110mm with jali 50 mm minimum seal suitable for kitchen all complete.

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and One Number,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Supply, installation of PVC vent cowl of working pressure 4kg/sq.cm including jointing with adhesive solvent cement including fixing the same in true line and level… etc.

75mm dia

EXTERNAL PLUMBING

Supply, Unloading, Storing, Safe keeping, shifting, installing, testing & commissioning of Anti Rodent Double Walled Corrugated Pipe (PE/PP) for storm water drain pipe installation confirming to IS: 16098, Stiffnes SN4, cut to required lengths including coupler, Tee, Bend to correct levels below ground in trenches upto required depth including excavation in all kind of soil including (hard Rock) dewatering, refilling,watering, ramming and removing the surplus excavated material and making good the same complete as required for sewage drain. Making proper connection with coupler joint of required depth as per manufacturer. Cutting, chases / holes in walls / slab to the satisfaction of the project manager / consultants and making good the same after pipes have been duly laid and testing complete

External - For sewage

160mm dia

Supply, Unloading, Storing, Safe keeping, shifting, installing, testing & commissioning of socketed and spigotted RCC pipes (HUME pipe) (NP2 Class) confirming IS: 458 jointed with rubber rings & laid to correct levels below ground in trenches upto required depth including excavation in all kind of soil including (hard Rock) dewatering, refilling,watering, ramming and removing the surplus excavated material and making good the same complete as required for rain water dispossal.

External - For SWD / Rain Water

160mm dia

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75Kilogramwith lid and frame fixed in cement concrete.

Constructing water tight brick masonry catchbasin with first class bricks in cement mortar 1:6 (1cement :6 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement :2coarse sand :4 graded stone aggregate 20mm nominal size). Foundation concrete 150mm thick 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement plaster 1:3 (1cement :3 coarse sand) finished with a floating coat of neat cement and making channel in cement concrete 1:3:6 mix neatly finished, complete as per standard design and approved drawings including manhole cover as specified below. (Price shall include the cost of excavation, back filling, disposal of suplus earth dewatering & water proofing of manholes as directed at site & other associated civil works).

Internal size 600 x 600 mm upto 0.9 m deep with perforated grating of SFRC to take weight of 4 wheeler.

Supply, Unloading, Storing, Safe keeping, shifting, installing, testing & commissioning off in position 100mm dia gully trap in brick masonry chamber of 300mm x 300mm including embedding the gully trap in cement concrete 1:2:4, (1:6) plastering, curing, effecting necessary connections and providing bitumastic painted special Chamber cover of THERMODRAIN FRP Capable of taking 2 wheeler / light vehical load (5MT).

Providing & Constructing surface drain with 9" burnt brick masonry plastered on both sides with 3/4" thick in cement morter 1:3 including 18" dia glazed stoneware channel at bottom fixed in cement concrete 1:4:8 bedding given required slope, curing, necessary excavation, refilling the sides etc. complete including 50mm thick grating as per design etc.

300mm wide

600mm wide

UPVC Pipe uPVC (Unplasticized Poly Vinyl Chloride) water supply pipes with Schedule 40 Pipe and schedule 40 fittings. Pipes shall be joined using solvent welded uPVC sch-40 fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, bushings etc. including transition fittings (connection between uPVC & metal pipe/GI) i.e. Brass Adapters (both Male & Female threaded) conforming to ASTM D-2467. with only uPVC solvent cement conforming to ASTM D-2564. All termination points for installation of faucets shall have brass termination fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings. Cost shall be inclusive of excavation in all kind of soil including (hard Rock), excavating trench for pipe laying, dewatering, refilling,watering, ramming and removing the surplus excavated material and making good the same, (a) wall/RCC wall cutting, chasing & making good as same as before complete as required for main incoming water supply line

50 mm dia

SS Pipe Stainless Steel 316 grade water supply pipes with fittings i.e. Tees, Elbows, Couplers, Unions, Reducers, bushings etc. including transition fittings. Installation shall be to as per Technical Manual of manufacturer of pipes & fittings. Cost shall be inclusive of excavation in all kind of soil including (hard Rock), excavating trench for pipe laying, dewatering, refilling,watering, ramming and removing the surplus excavated material and making good the same, (a) wall/RCC wall cutting, chasing & making good as same as before complete as required for main incoming water supply line

50mm dia

Constructing masonry valve chamber with first class brick work in cement mortar 1:5 (1cement :5 coarse sand) for valves. Concrete slab 1:2:4 (1cement:2 coarse sand :4 graded stone aggregate 20mm nominal size) necessary excavation, foundation conc. 1:5:10 (1cement :5 coarse sand :10graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement :3 coarse sand) finished with a floating coat of neat cement complete as per standard design.

600 x 600 x 600 mm internal dimensions with C.I.cover and frame of 38kg wright.

Providing and fixing 150mm diameter water meter with non-return valve including strainer, sockets/ union nut and including water meter box making locking arrangement and lock.[Without chamber]. Water meter certificate duly certified by Municiple authorities to be submitted along with handing over document.

50mm dia

Providing & Fixing of 150mm dia Sluice valve with necessary fittings & accessories.

Providing and fixing high-density polyethylene (HDP) container one piece moulded water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres.

PUMPS

Pressure Pump

12-6-1 Supplying & erecting pressure booster pump, single phase, 50 Hz, A.C. supply of 0.375 kW/ 0.5 HP, with discharge of 210 to 60 lpm for 10 to 40 m head & 25 mm suction/ 25 mm delivery pipe, for domestic pressure boosting applications (with 2 ltr water tank) as per specification no. WP-PP

Supplying, erecting, testing and commissioning of flat flexible 3 core 6 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying, erecting, testing and commissioning of water level controller 230/415 V, A.C. supply , four way under ground & over head tank operation only.

Supplying, erecting, testing and commissioning of PVC coated 5 mm dia. brass sensor/electrode duly wired with nuts & bolts complete (Set of 3 nos).

The work includes design, supply, fabrication, erection, testing, and commissioning of the complete fire fighting system. The tenderer shall fill in the columns of rate and amount and submit the same alongwith the all technical details.

PIPES & VALVES

Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 32 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 40 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Providing coating of bitumen paint & pipeline corrosion resistant Pypkote tape conforming to IS 10221 Appendix B specification having 4mm thick wrapping for underground ring main upto 250mm of fire fighting system. (Pypkote tape comprises of a Tar based Polymeric mix supported on a fabric of high tensile strength Fibreglass).

Supplying, erecting, testing and commissioning of horizontal sidewall quartzoid bulb sprinkler, 15 mm (½") dia quartzoid bulb. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR/SS

VALVES AND ACCESSORIES

Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF- VL/BFV

Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 25 mm Ball Valve complete with PN16 pressure rating, as per specification no. FF-VL/BV

Supplying, erecting, testing and commissioning vane type water flow detector 75/80 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes. as per specification no. FF- SPR/WFD

FIRE EXTINGUISHERS AS PER IS 2190

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 6 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supply, Installation, Testing & Commissioning of ISI marked portable fire extinguisher of ABC type (gas pressure) 6kg capacity as per IS:13849 complete in all respects including initial fill.(MR)

6 ltr. Fire Extinguisher K Class Kitchen Wet chemical SS BODY (Blend of Potassium Acetate, Potassium citrate or Potassium carbonate), Applicable fire class K type fire Extinguisher Kichen, at all places involving use of cooking fats and oils at high temperatures Like Canteen, Hotels, Restaurants, Food Courts, all small and big kitchen.confoming to Standard code IS:15683:2018

Civil Work

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal disposal of unserviceable material outside ACTREC campus as per direction of Engineer-in-charge.

CONCRETE BREAKING: Breaking of the existing concrete/brickwork by chiselling at all level including scaffolding and staging and the work shall be carried out so as to cause minimum inconvenience to hospital activity including cost of all material, labour, tools etc. carting away the debris out of hospital premises all complete as specified and directed. Rates also includes core cutting in concrete.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand)

STRUCTURAL STEEL WORK: At all levels including supplying cutting fabricating welding or blotting erecting and fixing in position including application of primer and synthetic enamel paint of approved colour as per the instruction of Engineer incharge

Structural Consultant for designing the floor deck and the complete shed and also providing Stability and waterproofing expert opnion with certification and monitoring.

Providing & laying Cast-in-situ RCC M25 Grade of concrete. REINFORCED CEMENT CONCRETE: (RCC) Reinforced cement concrete of M25 grade using graded stone aggregate of 20mm max. size including consolidation with vibrator & needle of required capacity finishing Curing including cost of form work, shuttering and excluding cost of steel reinforcement etc. complete all as directed by the Engineer-in Charge.: for Lintel, Internal beam in brickwork, etc.

Providing and Applying 1'' thk (12-20mm) average cement sand plaster to wall ,column, beam etc in cement and sand in proper plumb & right angle as per instructions. With 1:4 (1 cement: 4 fine sand)

Fixing of chicken mesh jali for plastering work for RCC - BW joint

Providing and Laying IPS Indian Patent Stone flooring of 50 to 70 thk with mixing of 1:4 cement, sand for leveling floor

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Providing and Fixing white marble 3'' to 6'' wide window cill from external face for all four side for Aluminum track sliding window in position.

Providing and Applying one coat of waterproof base coat on existing slab and wall up to 12" - 18'' or more height and applying second coat of cement plaster with mixing polycrete waterproofing compound for the same for toilet floor and wall complete.

Providing and laying water-proofing treatment of for sunk slabs of toilets and wherever necessary at all the levels with brick / stone aggregates (brick bat coba), with layer of 20 mm thick cement mortar 1:3 (1 part cement : 3 part coarse sand) mixed with water proofing compound of BASF, SUNANDA, FOSROC or approved make and as specified by the manufacturer, laying brick bats of required size in 100mm layers and providing cement mortar in between such that brick bat is impregnating in to the base mortar bed with gap of 12 mm all around according to slope, level and curing the same, the gaps around brick bats filled with cement mortar 1:3 (1 part cement : 3 part coarse sand) mixed with waterproofing compound, 20-30 mm layer above brick bats and finishing top with neat cement @ 2.75 Kg/Sq.M. screeding and curing etc. in line, level and plumb / slope, complete. (Note : The above rates shall be inclusive of Providing and mixing of waterproofing compound as per manufacturer's specifications and as decided by the Engineer incharge)

Providing and laying Vitrified tiles in floor and walls and Skirting in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid/Polished as approved by Engineer incharge finish of size 1200 to 1200mm

Providing and laying Vitrified tiles in floor and walls and Skirting in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid/Polished as approved by Engineer incharge finish of size 600 to 600mm

Providing and Fixing Designer premium quality tiles for - wall in toilet as per drawing and instruction including beading material as polymer adhesive with Laticrete / bal make with polymer grout for jointing etc. complete. Approval shall be as per the recommendation of Architect and Engineer incharge.

P & Fixing Designer premium quality tiles for - wall in Reception as per drawing and instruction including beading material as polymer adhesive with Laticrete / bal make with polymer grout for jointing etc. complete.Approval shall be as per the recommendation of Architect and Engineer incharge.

P/Filling polymer Laticrete grout for 4 mm groove wherever required as per the instruction of Engineer incharge

P/Filling polymer Laticrete grout for 4 mm groove wherever required as per the instruction of Engineer incharge

Providing and laying machine cut, mirror polished Engineered/Composite Marble in required design (Simple geometrical, abstract etc.) and in patterns in combination with different colours, shades and finished surface texture etc., giving a seamless finish, all complete as per the architectural drawings, with 18-20 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with type - 2 Adhesive as per IS 15477-2004, including pointing and grouting as per the technical specification in the tender. etc. all complete as specified and as directed by the Engineer-in-Charge. Seamless finish to be obtained as per the guidelines given in the tender specification.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias, cladding and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red

Designer Stainless Steel Signage displaying Morgan Stanley Waiting Lobby at the entrance over the granite cladding with proper borders. The signage shall be backlit, size more than 6 inches and design as approved by Architect and engineer incharge.

Providing & Fixing Baffle type false Ceiling with Metalworks Blade/ Linear Panels. Durable metal vertical panels in multiple size with swivel attachements. Pre-coated wood-look finishes. Standard sizes shall be 4" depth with 1" width with end caps both field cut and factory applied as applicable. Design pattern to be submitted for approval. Suspension system to be provided with non-corrosive metal or galvanised metal with additional supports.

Providing and fixing false ceiling at all heights with 15 mm thick integral densified calcium silicate/cementitous board hilux (as instructed) reinforced with fibre and natural filler false ceiling of approved texture, design and patterns, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm. Including one coat primer and two coat paint of approved shade and quality.

suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in- Charge.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

GI Metal Ceiling Lay in plain/perforated Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Door Frame - Fixing door frame using 19mm & 12 mm plywood to take on laminate finish from all sides.

Providing & fabricating Door using 32mm Commercial flush board with the both side laminate(sunmica) with standred hardware fitting such as Nail, Screw etc. as per design & details Completed.

Concealed Door Closer as per the requirement and instruction of Engineer incharge.

Providing & Fixing of the Aluminium fully Fixed windows as per the specification below,made out from Anodised Aluminium extrusions with 20-25 microns Anodizing. Special Grade EPDM rubber beading, Silicone Sealant of approved make and also with complete fitting at site with proper embedding in the structural framework. Required as per drawings and instructions of the Architects/ Consultants & all complete fitting at site. The Aluminium Frame shall weigh be more than 1.55Kg/m. All gaps between civil/structural work and aluminium frames shall be sealed and made watertight by applying silicone sealant and with good quality hardware and accessories like GI screws, Virgin PVC ,gaskets, silicon sealant on the periphery, as per detailed drawing etc. complete. All the section and design of ceiling shall be approved by Engineer incharge before the procurement of material. Providing and fixing Spacer Frame of approved make as per the instruction of Engineer incharge. Providing and fixing double glazed hermetically sealed glazing in aluminium ceiling, ventilators and partition etc. with 6 mm thick clear toughened float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Supply and Fixing of Slim openable Aluminum door of 8-12mm thick Toughened Glass with designer etching including providing and fixing top & bottom pivot & floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle size 600mm Center to Center, lock and stopper etc. included in the item rate). as approved by Architect using sleek anodised alumnium section (anodising of approved colour) with complete glass of maximum dimension 3m or as per drawing. The Fixed glass to be fixed using approved Profiles of aluminium at Top & Bottom & at sides (the profile to shared for approval). The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. The Profile shall be 20 micron matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness including 20 Micron of Anodizing of approved colour. The item is included provision for Floor springs of approved make. All complete as per the instructions of Engineer incharge.

Providing & Fixing High pressure laminate Panelling work with 12 mm panel with appropriate boxing and support arrangement with all completed work as per the instruction of Engineer incharge.

Providing & Fixing decorative Veneer Panelling work with 12 mm ply with all completed work as per the instruction of Engineer incharge,

Providing and fixing Wall cladding of made out of PVC fluted panels of wooden finish with grooves and patterns fixed on 6mm thick plywood. Final finish will be in similar to wood finish of approved pattern and colour as directed by engineer in charge.

Providing & Fixing 5mm Mirror Panelling with 12 mm ply with all completed work

Pelmet Providing and fixing pelmet 6" deep 1' height, using 19mm MR Grade plywood with 4mm waterproof MDF for all visible surfaces, including all necessary hardwares, etc. complete

Providing and constructing Reception Table and size as per drawings, with top, sides and bottom in 19mm thick commercial ply , back in 8mm thick commercial ply, intermediates in 19mm thick commercial ply , shutter in 25mm thick commercial grade block board. All external surfaces to be finished in approved laminate, with balancing laminate on the interior surface. All edges to be finished with lamiante . Drawers to be made in 12mm thk . commercial ply .Rate to include hardware such as approved locks, auto closing hinges for shutters, approved handles, door stop, tower bolt, etc. complete.

Providing & Constructing 15" deep Storage in 18mm commercial plywood finished in laminate internally and externally including necessary hardware like nails, screws, hinges S.S studs, locks etc complete. The cabinet should have internal compartments as per the design and instructions. The shutters shall be openable or sliding as per the instruction of architect and engineer incharge. The work shall be executed as per the instruction of Engineer incharge.

Supply and Fixing of Slim/Sleek Aluminum partition of 12mm thick Toughened Glass with designer etching as approved by Architect using sleek anodised alumnium section (anodising of approved colour) with complete glass of maximum dimension 3m or as per drawing. The Fixed glass to be fixed using approved Profiles of aluminium at Top & Bottom & at sides (the profile to shared for approval). The profile size to be 45x25MM to be fixed on to the floor/wall/ ceiling as per the architect design. H Junction profile to be used at all Glass to Glass vertical joints, 90 Deg L Junction Profiles and T Junction profiles necessary as per design. The profiles shall be suitable for Glass thickness of 12 mm.The Profile shall be 20 micron matt natural anodized, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 2 mm Gauge thickness including 20 Micron of Anodizing of approved colour. All complete as per the instructions of Engineer incharge. Additional Aluminium or MS support as per the instructions to be provided.

Providing & Constructing 18" deep Storage in 18mm commercial plywood finished in laminate internally including necessary hardware like nails, screws, hinges S.S studs etc complete.(Reception Side) Glass Shutter Considered

Reception Chair : Libro MB Back Height - Medium Back Back Finish - Mesh with adjustable lumbar support Back Frame - Black Color, Seat Finish - Fabric - Black Seat Height Adjustment - Pneumatic Mechanism - Synchronized Tilt Back Tilt Lock - Upright Position Back Tilt Tension - Adjustable Armrests Type - 1D Height Adjustable Armpads Type - Metal Base Type - 5-Star in Nylone Base

GF Waiting Chair : Providing and Supplying Metal Waiting chair with cushions as per the 3d design/drawing having Seat made of Perforated Cold Rolled Steel Epoxy Powder coated having thickness of 1.2mm. Arms and Legs are made of Aluninium for superior Strength and durability. Seat Seat Frames are supported on Steel Beams with thickness of 2mm duly powder coated. Seat and Back are single piece duly Epoxy powder coated. Sample to be approved by engineer incharge prior to procurement.

Mezzanine Waiting Chair : Providing and Supplying Metal Waiting chair with cushions as per the 3d design/drawing having Seat made of Perforated Cold Rolled Steel Epoxy Powder coated having thickness of 1.2mm. Arms and Legs are made of Aluninium for superior Strength and durability. Seat Seat Frames are supported on Steel Beams with thickness of 2mm duly powder coated. Seat and Back are single piece duly Epoxy powder coated. Sample to be approved by engineer incharge prior to procurement.

Café Area Table: Size maximum 1500*1500mm. Top : Laminate of approved colour on all sides (1mm thick) on top of Marine Plywood of thickness 18mm. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. Edge banding of approved colour as per the instruction of Engineer incharge. Understructure to be made of MS with powder coating with the appropriate support as per the instruction of Engineer incharge.

Café area Seating Chair : Cushioned chair with durable fabric with sturdy support structure of wooden frame and legs french polish as per the 3d render and design approved by Engineer incharge.

Plastic paint on Ceiling :Sand papering, cleaning the surface thoroughly, filling the cracks/holes with p.o.p, applying 1 coat of cement primer, 2 coats putty, sand papering for smoothness, applying 1 coat of synthetic enamel for hardness, applying 2 coats of paint with sand papering & doing require touch up before every coat including in grooves of 6". Asian Paint

Royal paint on Wall :Sand papering, cleaning the surface thoroughly, filling the cracks/holes with p.o.p, applying 1 coat of cement primer, 2 coats putty, sand papering for smoothness, applying 1 coat of synthetic enamel for hardness, applying 2 coats of paint with sand papering & doing require touch up before every coat . Inlcuding painting in grooves of 6". Asian Paint

External Painting: Providing and applying One coat primer and one waterproof base coat and two coat of textured Elastomeric paint of approved make, quality and colour including scrapping the surface to remove all loosely adhered particles followed by washing with water then wire brush so as to ensure thorough cleaning and opening up all the visible cracks in the plaster, in V- groove fashion using electric cutter machine. Fill up these cracks with cement past and polymer in ration of 1:1. Finish the same to ensure crack matched plaster level all complete as per the instruction of engineer incharge. Minimum : (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm. The work including Scaffolding.

Providing and Applying Malamine Polish to wooden vineer surfacewith all required finished

Providing and Applying Duco Paint to MDF surface with all required finished

Providing and fixing of Planter boxes made out of 12mm thick plywood with 1mm thick laminate of approved colour and of following sizes with artifical plants or creepers approved by engineer In charge. 200mm x 200mm (Square hollow boxes) as per the drawing given in the tender. Fixing as per the instruction of Engineer incharge.

Providing and fixing of Planter boxes made out of 12mm thick plywood with 1.5mm thick laminate of approved colour and of following sizes with artifical plants or creepers approved by engineer In charge 1200mm x 300 mm rectangular planter including placing over SS pipe of size 12mm square with a height of 900mm - 1200mm with artificial plants. Fixing as per the instruction of Engineer incharge.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On Concrete work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Providing and fixing sun control films 1.5 mil thick garware film on window glasess without damaging rubber gaskets, handle , friction hinged etc complete including neccesary scafolding job is to be complited as per garware film specification and as directed by EIC

Providing and fixing fabric backing commercial grade wall paper of approved shade with recommended adhesive of approved make which have 100% washable, scratch resistance, peel proof, and fire retardant properties. The wall paper should give a seamless finish. Including Cost of preparation on the base surface for fixing the wall paper as per the manufacturer specification, complete in all respect as per direction of EIC.

Providing & fixing roller blind Faber quality or equivalent motorised curtain with remotes control in Conference room, complete in all respect & as directed. Premium quality with heavy duty roller brackets & necessary fixtures. Warranty for roller mechanism & others accessaries shall be for One year from date of installation. [AS PER SAMPLE APPROVED] [Payment will be made on actual Mesurement basis. Windows mesurement to be taken before installation of roller blinds for achieving one piece work. ]

Glass Canopy Ceiling : Providing & Fixing of the Aluminium fully Fixed ceiling panel as per the specification below,made out from Anodised Aluminium extrusions with 20-25 microns Anodizing or 50 microns Super Durable Powder Coating,. Special Grade EPDM rubber beading, Silicone Sealant of approved make and also with complete fitting at site with proper embedding in the structural framework. Required as per drawings and instructions of the Architects/ Consultants & all complete fitting at site. The Aluminium Frame shall weigh be more than 1.55Kg/m. All gaps between civil/structural work and aluminium frames shall be sealed and made watertight by applying silicone sealant and with good quality hardware and accessories like GI screws, Virgin PVC ,gaskets, silicon sealant on the periphery, as per detailed drawing etc. complete. All the section and design of ceiling shall be approved by Engineer incharge before the procurement of material. Providing and fixing Spacer Frame of approved make as per the instruction of Engineer incharge. Providing and fixing double glazed hermetically sealed glazing in aluminium ceiling, ventilators and partition etc. with 6 mm thick clear toughened float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Staircase & Mezzenine Railing with Mild Steel as Material for Construction. The Railing shall be as per the design and drawing provided in the tender including welding and two coats of enamel paint of approved colour on two coats of rust proof primer (rust converter) all complete as per the instruction of Engineer incharge.

Providing and fixing of Aluminium pipe of size 100mm x 50mm with a thickness of 2mm having pre wood finished with not less than 50 microns wood grain Anodizing should be erected as vertical pillar as shown in pillar. The pillar shall be fixed on the ceiling with L-bracket/Cleats and on the floor should embeded by cutting tiles inserting the section below and finishing the surface. Shown in Fig 001 and drawing attached with the tender and as per the instruction of Engineer incharge.

Providing and fixing various colourful plantation for entrance area as per the plants list provided by the engineer incharge. The plantation shall be arranged in design as approved by the architect. The complete design alongwith Plants to be approved before proceeding with the work

Preparation of Lawn and landscaping for planting on ground: Transporting and disposing of bad soil and debris in to a suitable place out of the centre at this own cost. Filling the excavated areas by red soil (including the cost of red garden soil) for desire level, spreading of red garden soil to the required thickness .All over the area, mixing, rough dressing of area, spreading of 5cm thick layer of manure (including the cost of manure) and mixing properly with soil consolidation with water, fine dressing with preparation of beds by maintaining proper level and slope.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. : Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; including the cost of centering, shuttering, finishing and excluding cost of reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works above plinth level upto floor V level : Concrete of M30 grade with minimum cement content of 350 kg /cum

Mezzanine Floor Area: Providing and fixing roofing consists of 0.80 mm thick galvanised steel deck sheet confirming to IS: 277-1992 used as permanent shuttering over which MS wire mesh 3 mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structuralsteel beam with shear studs. (Structural steel like Beam, column, joists

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/m² with colouring all complete as per the instruction of engineer incharge

HVAC System

Package Unit DX type

Supply, Installation, Testing & Commissioning of 11 TR capacity Air Cooled Package Air Conditioner unit (Duct connection type) as per the folowing technical specification: Nominal Cooling Capacity (TR): 11 TR Rated cooling Capacity, Refrigerant: R-410 A or R-407 or any other (Ecofriendly) External finish: pure polyster powder coated GI steel housing. The unit to include built in contros like HP/LP/OL/UL/TEMP,SPP, PHASE SEQUENCE RELAY Display of same. INDOOR UNIT (IDU): Type of Blower: Centrifugal forward curved, double inlet double width. Air Filter: Non-Woven polyster Media enclosed with HDPE mesh. Controller: Factory fitted Microprocessor based with LCD display showing PV and SV value. Evaporator Coil:Hydropholic blue fins anticorosion coating. Compresssor Type: Hermetically sealed scroll (High energy efficient). No of compressor Unit: 02 ( double ckt) OUTDOOR UNIT ( ODU) : NO.of ODU : 02 NOs, Condenser Type: AIR COOLED FTHX,Hydropholic blue fins anticorosion coating. Condenser Fan Type : Proppeler. THE UNIT SHALL BE DESIGNED TO OPERATE EFFECTIVELY AT HIGHER AMBIENT TEMPERATURE,

DX HI-WALL UNIT

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 or eco friendly gas having copper condenser with blue fins, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC.

Refrigerant Piping: Supply , Installation, Testing & commissioning of Hard drawn copper tube complete with all accessories and support between indoor & outdoor units RMT indicated is for set of piping (Liquid+ Gas) between indoor and outdoor machine, (individual piping will not be measured]. Piping should be laid in GI tray with proper clamping. Note:- Package unit piping should have UV paint protecting from weather condition.

copper piping equivivalent to the Package Unit system.

copper piping equivivalent to the Hi wall Unit system. (Piping with 19 mm nitrile rubber insulation with GC cloth)

SITC PVC drain pipe having pressure holding of 6kg/cm2. Drain piping complete with all accessories with 12mm Nitrile Rubber Insulation

Dia 25mm

Dia 40 mm

Dia 50 mm

Supply, laying & termination of copper cable from Departmental power supply to IDU & between IDU and ODU unit. Complete with lug fitting, ferruling, gland fitting etc. All Cable should be laid in GI tray.

copper cable for Package units

Copper cable for Hi wall units

GI DUCT: Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications and as per SMACNA standard of following sheet thickness complete as required.

Thickness 0.63 mm sheet ( 24 SWG)

Thickness 0.80 mm (22 guage)

Thickness 1.00 mm (20 guage)

Thickness 1.25 mm (18 guage)

Insulation: Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Providing and applying of acoustic insulation for air ducts with 15mm thick, 48kg/cu.m fiber glass faced with RP tissue and covered with 26SWG perforated aluminium sheets complete.

Underdeck Insulation

Underdeck Insulation shall be soft with no irritation when exposed to human body. Product should have density of 24 Kg/m3 and thickness of 50 mm. It should be free from Formaldehyde and GREENGUARD Gold certified. Insulation has to be Hydrophobic. Fire resistance & should meets requirements of BS476: Part 4 (Non combustible), Part 6 (fire propagation), Part 7 (surface spread of flame). Fiberglass should be laminated with white facer. Facing to comply ASTM E84 for the test flame spread and smoke developed.

Plant Room Insulation

Acoustic insulation of AHU's surrounding walls (side walls and ceiling ) using 50mm thick glass wool, density 48Kg/CuM sections embedded in GI frame work of 600x600 grid on wall using 50x25x25 - 26G GI Channel sections and exposed surface finished with 24G GI Perforated sheet.

Supply, fabrication, installation an testing of flexible canvass connections constructed between ductable unit/dampers/ducting of suitable size with fire resist flexible double canvas sleeve complete

GRILLES / DIFFUSERS / DAMPER

Supply, testing, commissionig and balancing of one way / two way blow Aluminium extruded powder coated continuous Linear grilles for supply and return air with 4 side flanges and as per approved colour shade by the architect.

For SAG with box Damper

1000 mm x 150 mm

For EAG

100 mm x 100 mm

For DOOR Grille

600 mm x 100 mm

Supply and installation of below mention size of aluminum jet nozzle. Heavy gauge construction eye ball type with inbuit cone. Suitable for long throw( 360⁰ rotation ). Powder coated finish.

Supplying and erecting aluminium powder coated linear grill of suitable size for width length with collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45°.

Supply, installation, testing and commissioning of manually operated, opposed blade, duct mounted, flanged volume control dampers of required sizes in GI construction with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete.

Supply, installation, testing and commissioning of volume control box with collar for control damper of required sizes in GI construction with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete.

Supplying and installing of collar damper of galvanised iron material of upto 120microns for anti corrosive resistance for supply air grill of suitable size.

Supply, installation, testing and commissioning air curtain of 6feet width having air throw velocity of 21 m/sec, low noise level up to 38 to 46dBA suitable for door height upto 9feet, working on 1 phase, 230V, 50Hz, A.C. supply.

Supply, fabrication, installation and at the proposed location of M.S. base frame/platform for outdoor units complete with vibration isolation pads, supports, hangers, railing, brackets etc. Construction as approved by Architect/ Consultant. Apply epoxy painting on outdoor stand.

Supplying, Fixing,testing and commissioning of fusible link type fire dampers in supply air duct/main branch and return air path as and where required of required sizes . The damper shall also be closed in the event of fire complete as required and as per specifications.

MECHANICAL VENTILATION UNITS

Inline Ducted Fans

S/I/T/C of Duct Mounted centrifugal Fan with motor (Inline ducted fans)

400 cfm @ 5 mm external static (For Exhaust air)

300 cfm @ 5 mm external static (For Exhaust air)

S/I/T/C of Propellar fan (alongwith mounting frame arrangement) including 5 mtrs of power cabling.

SITC of Sequencial controller with all hard ware and cabling as require for UPS room units etc as per instructed and as directed by OIC-ES.

Spare filters set for Package units

ELECTRICAL WORK

SITC of LT Extension panel to be connected to existing main LT panel in RRU Building. Existing Panel Bus Bar is of Aluminium type" 02 Nos X 200mm X 10mm for each phases , 02 Nos X 200 mm X 10 mm for neutral , Incoming to be coupled from Main LT panel bus bar Outgoing Feeders 250a TPN MCCB 03 nos , 630A TPN MCCB 01 Nos , 400A TPN MCCB 01 NOS all MCCB are to be Minimum 35 KA , microprocesor bases , LSIG protection , rotory handle operating outside, ON OFF TRIP Indication. The AMF panel shall be indoor type, floor mounted, dust and vermin proof in sheet steel construction. The panel shall have doors at the front and back for proper maintenance. The panel shall have steel channel fabricated kick-plate and bolted type cable gland plate fitted at the bottom. The panel shall be constructed from 2 mm thick steel sheet. All the joints shall have proper gaskets. Monitoring and control devices shall be housed on the front door. Generally the construction of the panel will be such that various equipments for different applications will be housed in compartments. All incoming and outgoing power and control cables shall be from the bottom or back side.

Supplying, erecting, testing & commissioning of 3 kVA capacity on line pure sine wave,PWM,IGBT based UPS with 0.8 to unity output pf ,single phase input & 1 phase output , 230VOLT , 50 hZ. complete with all protections as per specification no. AP-UPS (Without batteries) The UPS to be used for networking , IT componants etc.The rate to also include Supply, Installation, Programming of software for BMS connectivity via RS232/RJ45 port for remote surveillance & control, inclusive of Battery set status monitoring. BMS Port shall be ready to use with all UPS Monitoring parameters. It shall be possible to trip the UPS through BMS System in case of Emergencies. Add for Active filters for to limit TH Di to less than 5%, if required, from load 50% to 100%. (Complete for EACH UPS System)

Supplying and erecting 12 V/65Ah SMF battery with battery terminal , interconnecting loops , wire, battery rack , battery circuit breaker / Fuse units , earthing , battery to UPS cabling copper type of rewuired size duly charged complete with 24 months warranty complete.

SITC of LT panel Incoming MCCB 400 A , LSIG protection Microprosessor base , 3 Phase+ Neutral , 415 volt , 50 Hz R, Y B incoming supply indication , ON OFF TRIP Indication , DIgital Ameter , Volt meter , MFM Meter , required rating of CT for metering , Outgoing Feeders 125A MCCB TPN 02 Nos , 250 A MCCB TPN 01 Nos , 63 A TPN MCCB 04 Nos , 32 A TPN MCCB 04 Nos all MCCB are to be Minimum 35 KA , microprocesor bases , LSIG protection , rotory handle operating outside, ON OFF TRIP Indication. The AMF panel shall be indoor type, floor mounted, dust and vermin proof in sheet steel construction. The panel shall have doors at the front and back for proper maintenance. The panel shall have steel channel fabricated kick-plate and bolted type cable gland plate fitted at the bottom. The panel shall be constructed from 2 mm thick steel sheet. All the joints shall have proper gaskets. Monitoring and control devices shall be housed on the front door. Generally the construction of the panel will be such that various equipments for different applications will be housed in compartments. All incoming and outgoing power and control cables shall be from the bottom or back side.

ELECTRICAL LOW SIDE

SIT&C OF LIGHTING FIXTURES & FITTINGS

Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600mA Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 Hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20 % having useful life of minimum 25000 Hrs with over heat protection with minimum 2 years as per specification No. FG-IDF/LED.

SITC of indoor bracket light with all accessories.

MCB DB'S / SWITCHGEARS

S.I.T.C. [Supply , Installation, Testing & Commissioning ] of MCB DB. ALL Indoor DB's to be IP43 & Ourdoor IP55. SITC of DB'S ready made [1.2MM THICKNESS MINIMUM] & as per 61439-3 or fabricated with 1.6MM MINIMUM THICKNESS as per design & site conditions or consultants requirements. TPN DB shall have 3 nos separate neutral links with internal wiring done as required with FRLS /FRLSH copper wires & cable as mentioned in boq, Internal terminations & wiring to be neatly dressed up in a systematic manner. All MCB to be 'C' & 'D' curve as mentioned & indicators to be LED All MCB & DB to be approved by consultant before procurement. DB to be fixed surface or recessed as per requirements

Supplying, erecting & marking FP MCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying, erecting & commissioning 2 pole RCCB WITH HPI 32A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete

Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 6 ways/phase (18 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on provided iron/GI frame (horizontal busbar type)

RAW POWER DB-1

Supplying, erecting & marking FP MCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Supplying, erecting & commissioning 2 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 6 ways/phase (18 poles), with door, 1.2mm thickness surface/flush mounted, IP43 Protection provided on iron/GI frame (horizontal busbar type) as per specification no. SW-MCBDB

Supplying, erecting & marking FP MCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying, erecting & commissioning 2 pole RCCB WITH HPI 32A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete

Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on provided iron/GI frame (horizontal busbar type) as per specification no. SW-MCBDB.

UPS DB

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCBO.

Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection provided on iron/GI frame as per specification no. SW-MCBDB

Supplying, erecting & commissioning 4 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB. Enclosure for Above mention Switchgear

EARTH PITS

Earthing pits to be provided to attain minimum resistivity of the soil .Mentioned are some of the makes ,other equivalent makes can be acceptable in case of non availability with prior intimation.[extra earth pits to be added if required to form a grid to reduce resistivity]

Tinned copper earth plate electrode 600 x 600 x 3.15 mm earth station, 2.5 mtr below ground level as per drawing complete with all required materials like Cole, charcoal, salt, brass nut bolts & washers, watering arrangements, GI pipe (B class), concrete chamber, heavy duty cast iron cover plate & excavation in all types of soil in ground refilling & removal excess earth within a radius of 500 mtr. Etc. Note:1.The chamber cover & plate shall be of heavy-duty hinged type & it shall weigh approx. 65 to 75 Kgs. For 450 x 450 mm size & shall be got approved by dept. (6 mm chequred plate with 40 x 40 x 6 mm angle iron frame)2.Plastering shall be done both inside & out side.3.The measurement of resistance of earth station & resistance of complete scheme of earthing layout shall be measured, recorded & got approved by Engg-in-charge.

Supplying and erecting copper strip 25 mm x 3 mm of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints as per specification no. EA-EP.

Supplying and erecting GI strip 25mm x 3mm of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints as per specification no. EA-EP.

S/F of 8 swg GI earth wire including anecessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints

S/F of 12 swg CU earth wire including anecessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints

S/F of earth bus bar 32 x 3 CU with powder coated ms enclosure 1.5 MTR Length

S/F of earth bus bar 50 x 10 GI with powder coated ms enclosure 1.5 MTR Length

S/F of 6 sqmm x1c pvc insulated green color coded wire in 20mm pvc conduit

Lightning Arrestor BOQ as per IS/IEC 62305-3, Level - II (Mesh Method)

Parallel Connectors with 2000mm air terminal, 16mm Dia Electrolytic Copper, connecting two conductors in parallel manner. Material- StSt, with clamping range- Rd / Rd 7-10 mm & Complied as per Standard EN / IEC 62561-1.

Universal connector of Material- StSt, with clamping range- 8-10mm, with truss head screw M10x35 mm & Complied as per Standard EN / IEC 62561-1.,

Roof / Parapet Conductor of Diameter Ø- 8 mm, Cross-section- 50 mm2, of Material- AlMgSi & Complied as per Standard EN / IEC 62561-2.,

Conductor holder for Roof / Parapet wall/Side wall of Material- StSt for Rd 8-10 mm & Fl 20 mm, Height- 20 mm, Weight 30 g & Complied as per Standard EN / IEC 62561-4.

Down Conductor of Diameter Ø- 8 mm, Cross-section- 50 mm2, of Material- AlMgSi & Complied as per Standard EN / IEC 62561-2,

Conductor holder for down conductor of Material- StSt, for Rd 8-10 mm & Fl 20 mm, Height- 20 mm & Complied as per Standard EN / IEC 62561-4.

Expansion Pieces at every 20 meter on horizontal connected by MV clamp. Material of the clamp- Al, Dimension Ø8 mm having Length approx. 395 mm & Complied as per Standard EN / IEC 62561-2.

MV Clamps (Multipurpose connecting clamp) of Material- Al, with clamping range Rd 8-10 mm, & Complied as per Standard EN / IEC 62561-1.

Cartage (lord glue) for metal shed

Earthing

UNI Disconnecting Clamps with intermediate plate for round and flat conductor of Material- StSt, Material thickness- 2.5 mm, with clamping range- Rd / Fl 8-10 / 30 mm, & Complied as per Standard EN / IEC 62561-1.,

GI flat (25x6mm) Strip. Having width- 25mm, Thickness- 6mm, Material- Hot dipped Galvanized Iron, Cross Section- 150 mm2 Coating thickness- Avg. 85+ microns. & Complied as per EN / IEC 62561-2.,

GI strip holder of material- Dow moulded compound, having height- 19mm, Slot Size- 25x6 mm.,

Copper bonded rod with Low carbon steel, high tensile strength copper bonded rod with min 254 microns of copper plating, UL listed with company name marked on rod. Diameter- 17.2 mm, Length- 3 meters, Material- Copper Bonded, Coating thickness- 254 microns, min, Approvals- Tested acc. IEC / EN 62561-2, UL 467.,

Environment friendly, RoHS certified, low resistivity Ground Enhancement material in 22.6 Kg pack to fill the bore area around the rod,

StSt 316 grade clamp to terminate the load on earth electrode. Dimension- 160x35x3 mm.,

Heavy Duty Poly plastic pit cover for withstanding 40MT of Load & material- Polymer Body & Cover, Product Code- HEP, Dimensions- 308 mm (L) x 308 mm (W) X 214 mm (H), Weight 2.5 kg (5.50 LBS).,

GI flat (25x6mm) Strip. Having width- 25mm, Thickness- 6mm, Material- Hot dipped Galvanized Iron, Cross Section- 150 mm2 Coating thickness- Avg. 70 microns. & Complied as per EN / IEC 62561-2. (for Interconnecting Earth Pits),

Lightnig counter - To count no of lightning strike & it can record the date and time of the lightning incident also tested as per IEC 62561-6.

CABLE & TERMINATION

SITC of Armoured Copper & Aluminium, XLPE, cabling to be laid in trenches , cable trays ,walls , floor , ceiling , with labelling as required ,with saddle , spacers in well dressed manner as required as per site conditions & consultant / architect. All cables shall be XLPE FRLSH Outer sheathed & pvc insulated wires to be FRLSH Outer sheathed unless otherwise mentioned

Aluminium Armoured Cables [A2XFY]

3.5 x 150sqmm cable aluminium armoured Main cable from LT substtaion RRU

SITC of 25 sqmm x 4 c armoured cable

SITC of Copper Armoured Cables [2XFY]

6 sqmm x 4 c copper armoured cable

16 sqmm x 4 c copper armoured cable

S/F of 6 sqmm x 1 c copper multistranded pvc wire in FRLS HMS pvc conduits

TERMINATIONS to Aluminium Armoured Cables with Double Compression Glands

150 sqmm x 3.5 c

25 sqmm x 4 c

TERMINATIONS to Aluminium Copper Cables with Double Compression Glands

6 sqmm x 4 c copper armoured cable

16 sqmm x 4 c copper armoured cable

S/F of 6 sqmm x 1 c copper multistranded pvc wire in FRLS HMS pvc conduits

CABLE TRAYS

Providing & erecting hot dipped galvanised perforated type cable tray manufactured from 16 SWG GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware.

CABLE ENCLOSER & HUME PIPE

Construction of RCC/BRICK Cable Chamber with suitable cover size:-600mm X 600mm X 750mm deep , including excavation, compaction, 230mm thick brick wall with inside and outside plaster , including 150mm thick PCC bed

Supplying and laying (including excavation of suitable width & depth up to 900mm) 160 mm outside dia, double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete.

LIGHT / FAN WIRING [ LHSFT/FRLS MMS 25/32MM PVC CONDUITS] Point Wiring Supply & Installation Important Note : Refer Electrical layout provided by architect for better understanding of SB's • All the lighting circuits switchboard inside and lighting panel inside ferruling to be provided as instructed by EIC ES. All the wirings light side, switch side, switch socket side , lighting and power panel side wire ferrule type lug to be provided. all wiring to be concealed or recess as approved by EIC ES

SITC of Light / Fan Point Circuit Wiring Direct to MCB DB or Switch Board as mentioned in respective drawings from Switch Board & Lights to MCB DB with 1.5 / 2.5 / 4 sqmm or as mentioned. FRLSH Copper Wires with Conduits with all Terminations in Copper Cable Sockets/ Lugs, using modular Switch Accessories including Chasing & Recementing for Recess boxes & Conduiting as required. Legrand (Myrus) or equivalent Modular switches for quote to be considered. Wiring to be done in if already laid Ceiling Cable Trunking and to be extended with Conduits to the exact location of point. Switch board to switch board Looping & Sub Circuit from DB shall be 2.5 sqmm x 3 wire. Switch board to Primary & Secondary Point wiring shall be 1.5 sqmm x 3 wire, DB to direct Primary Point Wiring shall be 2.5 sqmm x 3 wire & Secondary Point Wiring shall be 1.5 / 2.5 sqmm x 3 wire

SITC of Primary point wiring for light point/ fan point/ exhaust fan point/ call bell point with 2 x 1.5sqmm + 1 x 1.5sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed including medium class PVC conduit Heavy(HMS) / casing capping , with modular switch , modular plate, suitable GI box for concealled , suitable PVC box for surface , ceiling fan rose , PVC junction box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. (Average circuit lenght 20 mtr)

SITC Secondary point wiring light to light looping with 2 x 1.5sqmm + 1 x 1.5sqmm FRLS PVC insulated copper conductor single core cable in surface / recessed including medium class PVC conduit Heavy(HMS) / casing capping , with modular switch, modular plate, suitable GI box for concealled , suitable PVC box for surface , ceiling fan rose , PVC junction box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. ( Average circuit length 10 Mtr )

MAIN, SUB MAIN CIRCUITS WIRING FOR LIGHTING , RAW POWER, AC POWER AND UTILITY PURPOSE. [ LHSFT / FRLS MMS 25/32MM PVC CONDUITS ]

SITC of power point / circuit wiring direct to mcb db or switch board as mentioned in respective drawings including circuits from switch board & S/S to mcb db with 2.5 / 4 /6sqmm or as mentioned with FRLSH copper wires in MMS PVC conduits with all terminations in copper cable sockets/ lugs, using switch accessories including chasing & recementing for recess boxes & conduiting as required Wiring to be done in if already laid Raceways and to be extended with Conduits to the exact location of point & some extra conduits for future use. Legrand (Myrus) or equivalent Modular switches for quote to be considered. Wiring to be done in conduits or already laid floor aluminium race ways/ conduits which are considered seperately, however flexible conduits with partitions etc to be considered . Primary power points shall include circuits from respective MCB DB 'S.

SITC of Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable including surface/ recessed medium class PVC conduit Heavy(HMS) as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire from main distribution board to power point circuits and lighting switchboard.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable including surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire FOR POWER POINTS rate is for one circuit per meter ( i.e 2 X 4 sq. mm + 1 X 4 sq. mm earth wire)

Supplying and fixing following size/ modules, PVC / GI box alongwith modular base & cover plate for modular switches in recess / surface etc. as required. • All the power socket tagging to be provided , PVC tags to be provided. • All the power sockets inside and power panel inside wiring ferruling to be done as instructed by EIC ES

3 Module

6 Module

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Modular switch 6A/16A

Modular Socket 6A/16A

Supplying and fixing following ratings 240/415 volts, “C” curve, miniature circuit breaker suitable for inductive load of following poles including metal enclosure box , earthing and fixing accessories with connections,Testing and commissioning etc. as required. As per technical specifications in tender.

Supplying, erecting & marking DP MCB 6 A to 32 A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

Supplying, erecting & marking DP MCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-MCB

DP MCB Enclosure Box Metal

MCCB for HVAC Chiller incoming

63A TPN 415 volt , 3 phase neutral , 50 HZ MCCB including Metal enclosure ON OFF TRIP Indication , Rotary operating mechanism , LSI protection , Earthing , Neutral Link ,and accessories

11TR AC Power cables

SITC of 4 x 35 sqmm auminium armoured cable

4 x 35 sqmm armoured cable end connections with double compression gland and lugs and all required accessories

HAND USE TOOLS

Providing & Fixing of printed instruction chart for (with minimum 700 x1000 mm in size) treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete.

Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working up to 22 kV supply complete.

Supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution, etc. (All above contents shall be of standard makes)

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class B insulation conforming to IS: 15652 – 2006 having 2.5 mm thickness up to 11 kV

SITC of LED strip / rope light with aluminium profile

SITC of LED Strip light driver for every 5 mtrs

SITC of LED spot light 3 watt to 8 watt with integral Driver for side poster including secondary point wiring with 2x1.5 + 1 x 1.5 sqmm wire ( light to light looping including HMS PVC Coducit and all fixing accessories

Dismentling of existing electrical fittings / wirings as instructed by OIC ES.

FIRE FIGHTING WORK

The work includes design, supply, fabrication, erection, testing, and commissioning of the complete fire fighting system. The tenderer shall fill in the columns of rate and amount and submit the same alongwith the all technical details.

PIPES & VALVES

Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 32 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 40 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP

Providing coating of bitumen paint & pipeline corrosion resistant Pypkote tape conforming to IS 10221 Appendix B specification having 4mm thick wrapping for underground ring main upto 250mm of fire fighting system. (Pypkote tape comprises of a Tar based Polymeric mix supported on a fabric of high tensile strength Fibreglass).

Supplying, erecting, testing and commissioning of horizontal sidewall quartzoid bulb sprinkler, 15 mm (½") dia quartzoid bulb. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR/SS

VALVES AND ACCESSORIES

Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF- VL/BFV

Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 25 mm Ball Valve complete with PN16 pressure rating, as per specification no. FF-VL/BV

Supplying, erecting, testing and commissioning vane type water flow detector 75/80 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes. as per specification no. FF- SPR/WFD

FIRE EXTINGUISHERS AS PER IS 2190

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 6 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supply, Installation, Testing & Commissioning of ISI marked portable fire extinguisher of ABC type (gas pressure) 6kg capacity as per IS:13849 complete in all respects including initial fill.(MR)

Supply, Installation , testing, commissioning and handing over of Sand Buckets as per Tender Specifications. 16mm round bar and 25x25d steel angles of 3mm thickness to be considered. (Two Sand Buckets to be kept along with stand ) (MR)

6 ltr. Fire Extinguisher K Class Kitchen Wet chemical SS BODY (Blend of Potassium Acetate, Potassium citrate or Potassium carbonate), Applicable fire class K type fire Extinguisher Kichen, at all places involving use of cooking fats and oils at high temperatures Like Canteen, Hotels, Restaurants, Food Courts, all small and big kitchen.confoming to Standard code IS:15683:2018

ELV SYSTEM

FAS SYSTEM

Supplying, installing, testing and commissioning of Addressable Optical Photo Smoke Detector. The detector shall have multi co-operative sensing technology for faster response & avoid false alarms. The detector shall have single/twin bi-colour LED for 360 deg viewing. The detector is conforming to IS 2189: 2008, 11360_1985_Reff2020_EN 54 /VdS / UL & FM approved with 3 years equipment replacement warranty, Designed to meet UL268, 7th Edition. FF- AFAS/SD.

Supplying, installing, testing and commissioning of intelligent addressable thermal/heat detector with rate of rise cum fixed temperature thermistor complete with 0°C to 58°C temperature range, with base as required, single/twin LED’s with 360 degree view, in-built locking mechanism to check the removal and pilferage of the detector, Detector Shall conforming to IS : 2175 - 1988 reaffirmed 2000, IS 15908:2021 / EN 54 / VdS / UL & FM approved with 3 FF-AFAS/HD - ROR.

Supplying, installing, testing and commissioning of Addressable Multisensor/Multicriteria Photo Thermal (Smoke + Heat) Detector. The detector shall have twin bi-colour LED for 360 deg viewing. The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. This item is referred for Non-conditioning Area conforming to EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, Designed to meet UL268, 7th Edition.

Supplying, erecting testing and commissioning beam smoke detector four wire single ended reflected type with 8 " receiver having digital display for easy alignment, adjustable sensitivity & heater kit for transmitter/receiver and reflector with necessary connections on suitable back box. The protection range of beam detector is 5 to 100 Meters.

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI

Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with "Break Glass" massage embedded on the glass, complete erected with mounting base and required accessories, Module shall conform to EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FF-AFAS/MCP.

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

SITC of 2c x 1.5 Sq.mm FRLS Unarmoured cable. ATC conductor stranded, PVC insulated to form a core, Cores laid up, Overall shielded with Alu-mylar tape with tinned copper drain wire of size 0.5 Sq. mm, PVC innersheathed, PVC sheathed cable (Colour: RED )

Supplying and erecting LHSFT / FRLS MMS PVC conduit 25 mm dia. with accessories on wall /ceiling For unarmoured FA cabling

Supplying, installing, testing and commissioning of addressable fire control/relay module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs etc., Module shall conforming to IS 5051 Part 2 (Sec 1 to 3) : 1982 reed relays / EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FF- AFAS/CRM-FCM

Supplying, installing, testing and commissioning of addressable fire isolator module for isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the health status of the device. module complete as required. Module shall conforming to IS 5051 Part 2 (Sec 1 to 3) : 1982, , EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, FF-AFAS/ISM

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 1 loop capacity and capable of supporting not less than 250 devices and detectors per loop, with on-board LCD alphanumeric backlit display suitable for minimum 80 characters, operating at 230 V 50 Hz - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 minutes in alarm condition, The panel shall have suitable provision for network connectivity & compatible for third party integration(Open Protocol to communicate) via a MODBUS/BACNET interface etc. conforming to IS 15908:2021, IS 2189: 2008, NFPA-72, EN 54 / VdS/FM & UL 864(10th edition) with 3 years replacement warranty and inclusive of lifetime software license validity, as per specification no FF-AFAS/CP.V

Supplying, installing, testing, commissioning of Power Supply Unit of suitable rating for hooters.

For 4 Hooters

Supplying, installing, testing and commissioning of Addressable Sounder cum Strobe rated at minimum 75 dB @ 3m for Audible annunciation and minimum 75cd flashing at 1 Hz for visual indication. Module shall conforming to IS 2189: 2008, IS 15908:2021 / EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FF-AFAS/ S-ST

SITC of 2.5sq.mmx3 wire FR-LSH for providing power points to power supply units of LV system with 25mm HMS PVC conduit.

PAS SYSTEM

Supplying,installing, testing & commissioning 2-Way flush mount Ceiling Speakers with input power 20W RMS power, with power taps on 20/10/5W, 100V & 70V line, frequency response 90-18000Hz, stylish metal mesh grill and plastic frame, operates on 100V line for excellent reproduction of both speech and music, wide frequency response and adjustable tweeter complete as per specification no. PA-FMCS

Supplying Installing, testing and commissioning of PA Gooseneck Microphone with Base and frequency response 50-16000Hz, 150Ω to 200Ω impedence sensitivity 3 to 5.5mV/PA with minimum length(excluding pedestal) of 585mm(23") long, felxible stem gooseneck condenser microphone & Heavy Duty Metal Base having on/off switch, LED indication and Suitable for 48V phantom supply as per specification no. PA-GM

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

SITC of 2c x 1.5 Sq.mm FRLS Unarmoured cable. ATC conductor stranded, PVC insulated to form a core, Cores laid up, Overall shielded with Alu-mylar tape with tinned copper drain wire of size 0.5 Sq. mm, PVC innersheathed, PVC sheathed cable (Colour: RED )

Supplying and erecting LHSFT / FRLS MMS PVC conduit 25 mm dia. with accessories on wall /ceiling For unarmoured FA cabling

Supplying, erecting, testing and commissioning of 2 core 2.5 sqmm copper conductor shielded microphone cable complete as per specification no. PA- SMC

CCTV SYSTEM

SITC of 4MP IP DOME CAMERA, 1/3" CMOS image sensor, Output 4MP (2560 x 1440)@25/30fps, Max, H.265 codec high comprassion ration, Built-in IR LED, Max IR distance 30m,H.264 MJEPG,WDR-120db, SD card slot, Support max 256GB micro sd card, IP^& protection, Streams capacity 2, protection IP67,CE,ROHS

SITC of NVR unit for above required nos of cameras, H.265 Main Profile Hardware Compression, Real time 16 CH Record & Display, Trip Wire Detection, Guard, Counting, Intelligent Analysis, S.M.A.R.T. HDD Management for Redundant, Backup & Partition, 2 Port X HDMI, 2 Port X RJ 45, 1G LAN, VGA, BNC, Network Protocol [TCP / IP, UDP, DHCP, DNS, NTP, DDNS, SMTP, FTP, HTTP, SNMP, PPPoE, Alarm Server, Quick Play back & Backup], IOS / Android / Windows Mobile View, Capacity 4 nos HDD UP TO 6 TB, (4 nos x 6 TB) SATA HDD + 1 Port X E-SATA & All Camera Management Software with All Other Required Accessories. Certification: CE, FCC, UL,BIS, NDAA. CONSIDER 2 NO. OF 6TB HDD.

SITC of 2 TB hard disk SATA

Supplying, fixing, and configuring 12-port 10/100M un-managed 10/100/1000 base-T gigabit switch compliant with IEEE 802.3 standards as per specification complete.

Supplying and installing LSZH sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying & erecting 32" professional LED Monitor with 1920*1080 (Full HD) Display, suitable for 16 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

Supplying and fixing 15U wall mount rack (Dimension-DxWxH – 500x550x747 including RJ 45 patch panel and cable manager

VOICE (TELEPHONE) SYSTEM

Supplying and installing LSZH sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

SITC of CAT 6 [systemax/ d-link / amp / Legrand] I/O with back box, face plate & encl with wire termination for VOICE

SITC of caller ID Telephone

DATA SYSTEM

Supplying and installing FR PVC sheathed HDPE insulated copper cat-6A cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

SITC of CAT 6A [systemax/ d-link / amp / Legrand] I/O with back box, face plate & encl with wire termination for DATA

SITC of POE Manageable switch 16 port RJ 45 + 2 nos Fiber Port in floor IT rack for Data & Voice

SITC of POE switcher 8 port Fiber in floor IT rack

Branded CAT 6A Patch cord 1.5 mtrs

SITC of Single mode 12 core fibre optic cable for connectivity

SITC of Single mode 12 core fibre optic cable Terminations

SITC of branded & pre molded with connector HDMI 5mtrs cable

Fiber patch cord LC LC

TV SYSTEM

SITC of RG 6 antena wire for TV Signal with terminations with FRLS/LHSFT HMS PVC conduit (WIRE COLOUR - BLACK)

SITC of 43" LED 4K UHD smart LED TV with VGA input , 2HDMI port with Wallmount Stand , with remote and other accessories as per site installation and as directed by OIC-EIC Resolution: 4K Ultra HD (3840x2160) | Refresh Rate: 60 hertz Connectivity: Wi-Fi (Built-in) | 3 HDMI portse | 1 USB ports to connect hard drives and other USB devices | eARC | Bluetooth 5.0 | Optical | Ethernet Sound: 20 Watts Output | 2.0 Ch Speaker | AI Sound (Virtual Surround 5.1 up-mix) | Auto Volume Levelling | Bluetooth Surround Ready Smart TV Features: AI ThinQ & WebOS 22 with User Profiles α5 Gen5 AI Processor 4K | Display: 4K Ultra HD LED Display | 4K Upscaler | AI Brightness Control

SITC of 65" LED 4K UHD smart LED TV with VGA input , 2HDMI port with Wallmount Stand , with remote and other accessories as per site installation and as directed by OIC-EIC Resolution: 4K Ultra HD (3840x2160) | Refresh Rate: 60 hertz Connectivity: Wi-Fi (Built-in) | 3 HDMI portse | 1 USB ports to connect hard drives and other USB devices | eARC | Bluetooth 5.0 | Optical | Ethernet Sound: 20 Watts Output | 2.0 Ch Speaker | AI Sound (Virtual Surround 5.1 up-mix) | Auto Volume Levelling | Bluetooth Surround Ready Smart TV Features: AI ThinQ & WebOS 22 with User Profiles α5 Gen5 AI Processor 4K | Display: 4K Ultra HD LED Display | 4K Upscaler | AI Brightness Control

SITC of TV socket with co-box & face plate & encl. & complete in in all respect

SITC of 8 way splitter in 12" x 12'' x 2'' pvc box

TOKEN SYSTEM

Supplying & erecting visitor management token system as per technical specifications and as specified in DBR The system includes all required cabling , POE switches, Desktop computer of required configuration , and there must be anouncement as well display of token no on the screen for different applications / medical departments

S R DEVELOPERS (BID ID -3142354)

arcoma (BID ID -3141564)

VK A Architecture LLP (BID ID -3141330)