Providing Semi Unitized Glazing system for elevation of ALH Hangar at ACD

Name of the Individual / Firm / Company: * Mandatory

Type of ownership

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

PAN No.:

Goods and Service Tax ID No.

Contact details

Please Enter Contact person Name

Pls Enter Mobile No

Registered Contractor

Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs

I.T Returns for past 03 assessment years

Annual financial turn over during the last 3 years, ending 31st March 2025

TURN OVER IN Rs.

Pls Enter Turn over in Rupees for all the 3 years

ESI & PF Nos with proof

Remarks if any

Bank(s) details: [Copy of ECS and cancelled cheque leaf to be uploaded]

Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)

Solvency Certificate Details

Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs

Experience of having successfully completed similar works during last 7 years ending on the previous day of submission of tender [Work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Please enter Details for Work No 1

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No II

Type of Work: [ Incase of private works the same shall be supported with TDS certificate]

Pls Enter Details for Work No III

Details of person holding the power of Attorney (If different from contact person)

Related Document to be Uploaded to eProcurement Portal

Pls Enter Details for Person holding Power of Attorney

DECLARATION I

DECLARATION II

Pls Accept the Delaration II

Specification

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) etc., all complete as directed by Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for walls/plinth and tring cources etc., all complete as directed by Engineer-in-Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level with thermo mechanically treated bars etc., all complete as directed by Engineer-in-Charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, facias and similar locations of required size approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including bull nosing, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels etc., all complete as directed by Engineer-in-Charge.

Providing and fixing 1mm thick G.S. sheet roofing for shadow boxing at window areas etc., as required with coating of primer and two coats of approved paint including all the screws etc., all complete as directed by Engineer-in-Charge and site condition.

Providing and fixing of aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. for Semi Unitized System with use of minimum Vertical MULLION of section 81.16mm X67mm X 1.8mm and Horizontal TRANSOM 81.16 mm X 67mm X 2mm with Al.Cleats fixed with anchor bolts of M 10 X 9and 8mm SS Bolts 8mm. The al.profiles shall be supplied with protective tapes and to be removed after completion of the work. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment .

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing with 6mm thick Single Reflective Heat Strengthened from approved make of Glass (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including . [Glazing Only will be paid in this section of work. However, the submission of Design and Design Basis Reports is part of the specification for Semi Unitized Glazing System Please Refer details indicated below:] .

Extra for openable side / top hung vision glass panels/Refelcetive Panel including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the tentative drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100 mm upto 200 mm in RCC beams, lintels, columns/floors and slabs to introduce steel bars for sunshades/balconies/kerbs including fixing the steel bars in position using epoxy resin anchor grout of pproved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions andfacades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame ofClass A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applyinga priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge.

Supplying and Fixing of 4mm thick ACP over the 1mm thick Pre-painted GI Sheet of 1mm thickness as Coping Box Covering etc., all complete as directed by Engineer-in-Charge.

Supplying and fixing of S.S Bolt with washer of different sizes for structural glazing / ACP for Cladding and Coping etc., all complete as directed by Engineer-in-Charge.

Rupees Fifty Six Lakh Four Thousand Seven Hundred Forty Seven and Fourteen Paise Only

Approximate Amount Put to Tender

Rupees Ten Lakh Eight Thousand Eight Hundred Fifty Four and Forty Eight Paise Only

Rupees Sixty Six Lakh Thirteen Thousand Six Hundred One and Sixty Three Paise Only