8639 SPECIAL REPAIR TO BLDG NO - 67, BLDG NO 68 AT ZOZILA LINE AND PROVN OF 02 NOS DOG KENNAL AT 25 ARMY DOG UNIT AT OLD NDA COMPLEX UNDER GE (CENTRAL) PUNE

Amount

Taking down chowkats or frames with shutters without taking off shutter from the frame area n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters without taking off shutter from the frame area exc 1.50 Sqm but n-exc 4 Sqm each complete all as specified and directed.

S&F pressed steel frames 125 x 60mm for doors with one or more rebates including necessary fixing lugs, lock strike plate, etc.complete all as specified and directed.

-Ditto- all as item No 3 above but of size 105x60mm complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C1 (using 20mm graded stone aggregates) for filling of pressed steel frame and hold fast block cutting etc complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, both face to be covered with decorative face factory pressed veneer with lipping/frame to match complete all as specified and directed.

Supply and fixing( factory Made ) 2nd class hard wood 35 mm thick glazed and skelton shutters open rebated and prepared to receive gauge. (Without sash bars ) edges of framing plain chamfered or rounded both faces to be covered with factory pressed decorative face venears with lipping/frame fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I section 8 clause 8.20 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F Factory made wood grain printed (Prelaminated) solid PVC single door frame of size 50 x 47 mm with a wall thickness of 5mm prelaminated colour sheet reinforced with 19 mm x 19mm MS square tube having wall thickness 19 guge complete all as shown in sketch on page 150 of SSR 2004 Part 11 complete all as specified and directed.

S&F factory made wood grain printed (Prelaminated) solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes 19 mm x 19 mm having wall thickness 19 gauge for stiles. MS tube 15mmx 15mm having wall thickness 19 mm gauge for top and bottom rails. MS frame shall be covered with 5mm thick heat moulded prelaminated colour PVC 'C' channel having 5mm thick PVC sheet strip 20mm wide struck inside with solvent cement for stiles and 5mm thick PVC sheet for top rail, lock rail and bottom rail on either side and 10mm (5mm x 2mm) thick, 20mm wide cross PVC sheet as gap insert for top and bottom rail. Paneling of 5mm thick prelaminated colour PVC sheet to be fixed in MS frame welded/sealed to the stiles and rails with 5mm x 30 mm PVC sheet beading and jointed together with solventcement complete all as shown in drg give on page 146 of SSR 2004 part 11. The width of stiles and rails shall be as specified in para 8B.2.1 on page 134 of SSR 2004 part II.complete all as specified and directed.

S&F aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed

S&F Anodised aluminium window and partition shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, maruti lock, screws etc. and including powder coating complete all as specified and directed.

Supply and fixing 4mm thick sheet glass ordinary quality and glazing fixed to aluminium window / ventilator/ Door shutters / steel windows etc complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including fillets complete all complete all as specified and directed.

M&L for framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework ofwater tanks and similar work conforming to Fe.290.Gde-E-165 Complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of a red oxide primer complete all as specified and directed.

S&F glass ventilators/louvers using 5mm thick frosted/pin headed glass and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed. (a) SP - 20048 (b) Glazing clips - 19352. complete all as specified and directed .

S&F 150 mm extruded aluminium alloy handles ,fabricated type.complete all as specified and directed.

S & F Aluminium anodised barrel tower bolt of extruded section 150mm long all as specified and directed.complete all as specified and directed.

S&F mild steeel butt hinges 100mm, medium weight complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F in repairs stainless steel curtain rails 25mm dia with SS brakcet, knobs, end or wall brackets etc. complete all as specified and directed.

Supply & fixing Aluminium alloy anodised sliding door bolts with hasp and stapple (bolt type and fxing clips of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section of 250mm long complete all as specified and directed.

Demolition of cement concrete in ground floors and paving not exc 15 cm thick (below or above ground level) un-reinforced,cleaning the premises and removal of rubbish out side the MD land complete all as specified and directed.

M&L for Plain cement concrete type D-2 1:4:8 (using 40mm graded stone aggregate) as in foundation,levelling course etc complete all as specified and directed.

Demolition of brick work/stone masonry build in cement morter of any description and removing of rubbish outside the MD land complete all as specified and directed.

M&L for block masonry with solid blocks of precast cement concrete class designation D-5 (using 20 mm graded stone aggregate) exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off outside the MD land complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40 mm graded aggregate) of 75 mm thick as in plinth protection/PCC Path finished even and smooth without using extra cement laid in slope including necessary form work complete all as specified and directed.

M&L for non skid ceramic coloured tiles 600x600, 7 to 8 mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 20mm thick screed bed of CM 1:6 complete all as specified and directed.

-Ditto- all as item No-29 above but in skirting over and including 10 mm thick backing coat in CM 1:3 complete all as specified and as directed.

M&L for Non–Skid Ceramic Coloured Tiles, size 300x300x7 mm, laid on floor, over and including 15mm thick screed bed in cement mortar 1:6 Laid and Jointed in Neat Cement Slurry and pointed in White Cement with pigment to match the shade of the Tiles, complete all as specified and as directed.

M&L for Glazed Ceramic Coloured Tiles, 300X450X7mm in size, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick rendering in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles, complete all as specified and as directed.

M&L for rubber moulded glossy chequered cement concrete coloured tiles 30cm x 30cm x 20mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on brick/ stone surfaces finished even smooth without using extra cement including taking down of existing plaster complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a thin layer of wall care putty complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on brick/ stone surfaces finished even smooth with spong finish including taking down of existing plaster .complete all as specified and directed.

M&L for preparing new plastered surface of walls and applying two coats of cement based paint over a coat of cement primer of same make complete all as specified and directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a thin layer of wall care putty complete all as specified and directed.

Dismantling ceiling/boarding of any description, fixed in any position like partition etc with nails including frame work of timber complete all as specified and as directed.

M&L for 8 mm thick one side laminated gypsum ceiling board designer type for false ceiling on GI powder coated grid work 60 cm x 60 cm with using 36.5 mm x 23.5 mm x1.5 mm thick main tee, 23.5 x 23.5 mm x 1.50 cross tee and 25 x 25x 1.5 mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger of GI wire and 'J' bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 605 x 605 mm, complete all as specifed and direceted.

Dismantling single layer mangalore pattern or similar tiles in roofing etc complete all as specified and directed.

Dismantling battens for tiles of any size including tilting fillets spacing exc. 15 cm complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness in roof covering or wall cladding complete all as specified and directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe 410-W Gde-E250 complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick(AZ-150) fixed in any position where directed of any colour having tensile strength of 550 Mps as in roof covering/cladding to wall, fixed with self tapping screws or fixed with L type of J type hook bolts with one corrugation side lap, bent to shape complete all as specified and as directed.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick colour as in ridge and straight flashing with grade of zinc coating AZ-150 complete all as specified and as directed.

M&L for GI tubing 15mm bore fixed to walls, ceilings or laid in floors medium grade concealed all as specified including Taking up or down steel water tubing and connection including cleaning for refixing or removal to store of 15mm bore complete all as specified and directed.

M&L for GI tubing 20mm bore fixed to walls, ceilings or laid in floors medium grade concealed all as specified including Taking up or down steel water tubing and connection including cleaning for refixing or removal to store of 20mm bore complete all as specified and directed.

M&L for PVC water tank rotational molded polyethylene water storage tank hoisted & fixed in position ( with closed top) of capacity 1000 ltr including Dismantling water tanks exceeding 500 and not exceeding 1000 litres capacity and removing to store complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs vitreous china single piece pedestal pattern water closet white with including 'P' or 'S' trap, matching sheet cover including making good to floor, complete all as specified and directed. Make Jaquar cat part no: CNS-WHT-851 or Techno commercial equivalent model in KOHLER and ROCA.

S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. Make Jaquar cat part no:ALD-CHR-577 or Techno commercial equivalent model in KOHLER and ROCA.

S&F in repairs 15mm bore chromium plated two way bib cock fancy type complete all as specified and directed.. Make Jaguar cat part No FLP-CHR-5041PM or equivalent model in KOHLER and ROCA.

S&F in repairs Brass CP wall mixer for mixing hot & cold water with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting legs & wall flange and fixed complete all as specified and directed..Make Jaquar cat part no:FLP-CHR-5281PM or equivalent model in KOHLER and ROCA.

S&F in repairs 15mm bore chromium plated bib cock fancy type complete all as specified and directed.. Make Jaquar cat part no:FLP-CHR-5037PM5047N or equivalent model in KOHLER and ROCA.

S&F in repairs 15mm bore chromium plated angle cock fancy type complete all as specified and directed..Make Jaquar cat part no:FLR-5053N or equivalent model in KOHLER and ROCA.

S&F in repairs brass chromium plated shower rose 125mm size fitted to steel pipe or union complete.Make Jaquar cat part no:OHS-CHR-1989 or equivalent model in KOHLER and ROCA.

S&F in repairs PVC connection pipe 15 x 450mm.complete all as specified and directed.

S&F in repair 15mm bore chromium plated pillar cock fancy type complete all as specified and directed..Make Jaquar cat part no:FLP-CHR-5011PM or equivalent model in KOHLER and ROCA.

Supply and fixed in repairs 20mm bore PVC brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

Supply and fixed in repairs 20mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs vitreous china flat back type wash basin, white of size 550 x 400 mm including brackets,waste pipe and coupling complete all as specified and directed.

S & F in repairs chromium plated soap dish fixed with chromium plated brass screws complete all as specified and directed.

S & F in repairs brass chromium plated Tubular towel rail 20mm dia "D" type 60cm long.complete all as specified and directed.

S&F stainless steel plate rack made of 1.00 mm thick sheet grade SS- 304 of standard size 36"x36"x8" and of approved quality of finish all as spd and directed mark.complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors / walls complete all as specified and directed.

-do- all as item No-68 above but 75mm bore complete all as specified and directed.

S&F PVC (SWR) Nahani trap 75mm bore with SS grating with or without holes incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F 110mm PVC (SWR) bands complete all as specified and directed.

S&F 75mm PVC (SWR) bands complete all as specified and directed.

S&F PVC (SWR) cowl 75/100mm dia as required complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction double, (double T), equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) gully trap 150 x 100 square or round mouthed, type P incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

Dismantling of stone slabs and tiles of any description laid in CM in floors, approns etc including removal unserviceable tiles outside MD land complete all as specified and directed.

M&L for 18- 20mm thick granite (of any type) work table rubbed and pre polished) in cooking platforms, steps, vertical wall cladding and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixtures of pigment to match with shade of granite and including grinding / champhering of exposed / visible edges complete and ensure best adhesion to surface complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25mm thick for vertical supports of kitchen platforms and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing of the exposed face complete all as directed and specified

Demolition of uneinforced cement concrete of any description and in any position on roof slab/sunken slab as in padding etc including removing rubbish out side MD land complete all as specified and directed.

M & L for water proofing treatment to RCC roof slab, walls, chhajjas ets, shall be carried out as specified below and as directed by Engineer-in-Charge (a) Taking down existing tarfelt/membrane with plaster and clean the surface properly. (b) M&L for 10mm thick plaster screed bed layer in CM 1:3 on concrete surfaces. (c) Preparing plastered surfaces of roof slab, walls, chhajjas etc, by brooming with broom sweeping free from dirt dust etc & evenly applying a coat of approved bitumnous primer @ 1.20kg/Sqm of area complete all as specified. (d) Laying App polymer modified approved membrane, non woven, polyester, weighing not less than 3.5 kg/Sqm and 3mm thick with laps & overlaps as specified & joints sealed and applied complete by torch application method all as specified & directed by Engr-in-Charge. (e)Carrying out test by flooding water for 24 hrs for leakagge & seepages and rectifying the same to the entire satisfaction of GE. (f) Finally applying a coat of solar reflective bituminous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as specifed & as directed by Engr in Charge.

M&L for provinding cement concrete (1:2:4) B-1 (using 20 mm graded stone agreegate) as in copings / bearing course over brick walls etc and like complete all as specified and directed.

S&F in repairs 18/19mm thick MDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete as in shutter / shelves of cup boards complete and edges leeped with 6m thick teak wood lipping strips with nails etc compleete

S&F in repairs magnetic catcher for cabinet shutters with fixing arrangement complete all as specified and as directed by engineer-in-charge

S&F continuous piano hinges 30mm flap mild steel bright finish all as specified and directed by Engineer -in-Charge.

S&F in repairs 50mm dia, polished, hard wood knobs fixed with screws complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. and lift upto 1.5m, complete all as specified and directed by Engineer-in charge

Surface excavation n exc (not exceeding) 30cm deep and averaging 15cm deep and getting out soft/loose soil

Returning filling in soil including spreading, levelling, watering and well ramming in layers not exc 25 cm

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 05mm thick on ceiling CM(1:3) complete all as specified and directed.

M & L for preparation of newly plastered surface of ceiling and applying two coats of white wash over one coat of primer, complete all as specified and directed

M&L for TMT bar 10mm dia and over cut to length bent to shape reqd incl cranking bending etc complete & binding with MS wire (annealed) not less than 0.9mm dia in reinforcement complete all as specified and directed.

-Ditto- as above item No 92 but 8 to 10mm dia as in stirrups complete all as specified and directed.

Use and waste for formwork to rough finished flat surfaces of footing and plinth beams complete all as specified and directed.

Use and waste for formwork to rough finished flat surfaces of pillars, posts, struts, piers, columns and stanchions etc complete

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for reinforced cement concrete M-20 nominal mix type A1 1:1.5:3 (using 20mm graded stone aggregate) for foundations, including rafts, footings, plinth beams, bases for columns, etc complete all as specified and as directed.

M&L for reinforced cement concrete nominal mix M-20 type A-1, 1:1.5:3 (using 20mm graded stone aggregate) for columns, pillars, piers, posts and struts etc complete all as specified and as directed.

M&L for reinforced cement concrete nominal mix M-20 type A-1, 1:1.5:3 (using 20mm graded stone aggregate)Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for reinforced cement concrete nominal mix type M-20 type A-1, 1:1.5:3 (using 20 mm graded stone aggregate) for roof beams and lintels complete all as specified and directed.

M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M&L for 20 to 25mm thick machine cut Kota stone flooring over and including 20mm thick CM 1:6 screed base laid and jointed with grey cement slurrry mixed with pigments to match the shade of the slab including rubbing and polishing complete all as specified and directed.

ditto - all as above item No-103 but in riser of steps, skirting , dados and pillar laid over and including 10mm thick rendering to receive the stone in cement mortar 1:3 and jointed complete all as specified and as directed.

M&L for providing precast cement concrete louvres and jallies type B0,1:2:4(using 12.5 mm graded stone aggregate) 25mm thick (measured solid), including all mouldings but excluding frame and set in CM 1:4 all as specified and directed.

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and as directed.

M&L for Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and as directed.

M & L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and as directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as spcified and directed.

Taking down of existing Ceilling fan of any size and sweep and keeping safe custody and refixing the same existing place with serviceable condition by minor repairs such as capacitor replacement, bearing repalcement and painting, complete as per site requirement complete all as specified and as directed. Note : The quoted rate shall include the rates of spares and rewinding of fan mentioned above.

Supply and fix in replacement fan rod upto 6 feet as per site requirement complete with clamps (round/square) as per site requirement all as specified and directed

M&L for point wiring of any length using approved colour coding as per IS with stranded copper conductor 1.5 Sq.mm (Nominal area), two single core, PVC insulated and unsheathed stranded FRLS H cable 1100 volts grade, ISI - 694 marked colour code in PVC casing caping 25mm wide ISI marked including all accessories etc. with PVC modular boxes/PVC Sunken Boxes as required at site and as directed including modular frame/cover plate suitable for mounting switches/sockets etc. and PVC insulated stranded copper conductor 1.5 Sq.mm single core cable as earth and connecting to common earth dolly complete all as specified and directed for the following:- Note:- The quoted rate shall include necessary circut wiring of any length and taking down of copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custodyor for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc Making good of disturbed surfaces will be done by contractor without any extra claims.

One light point controlled by one switch complete all as specified and directed.

Two light point controlled by one switch

One exhaust/ fan point controlled by one 5 Amps one way modular switch and modular regulator complete all as specified and directed.

One call bell point controlled by push bottom.

One 5/6 Amp socket controlled by one switch same board complete all as specified.

One 3 pin 5 Amps Socket outlet point controlled by one switch on independent board complete all as specified

All as per item No. 113 above but with 2.5 Sq.mm(Nominal area), single core, PVC insulated and unsheathed multistranded FRLS H cable 1100 volts grade, ISI - 694 marked, including PVC insulated multistranded copper conductor 2.5 Sqmm single core cable for earth continuity conductor for one 3 pin 5/15 Amps switch socket / Earth plug socket independent and connecting to common earth dolly complete all as specified.

M&L for point wiring of any length using approved colour coding as per IS with stranded copper conductor 1.5 Sq.mm (Nominal area), two single core, PVC insulated and unsheathed stranded FRLS H cable 1100 volts grade, ISI - 694 marked in concealed PVC conduit medium grade of appropriate size as per specification as required at site and as directed including all accessories etc. with PVC modular boxes/PVC Sunken Boxes as required at site and as directed including modular frame/cover plate suitable for mounting switches/sockets etc. and PVC insulated stranded copper conductor 1.5 Sq.mm single core cable as earth and connecting to common earth dolly complete all as specified and directed for the following:- Note:- quoted rate shall include circuit wiring, cutting chasing and making good of disturbed surfaces will be done by contractor without any extra claims.

One light point controlled by one switch complete all as specified and directed.

One 3 pin 5 amps socket outlet point on same board complete all as specified.

One 3 pin 5 Amps Socket outlet point controlled by one switch on independent board complete all as specified

Supply and fix in replacement LED building security light 30 W IP 65 pressure die cast aluminium housing with GI bracket of suitable size complete including clamps , screws etc and dia complete all as specified and directed

S&F modular switch single pole one way 5/6 Amps including connection complete all as specified and as directed

S&F modular socket out let 5/ 6 Amps 3 pin incl connection complete all as specified and as directed

S&F modular bell push type single pole one way 5/6 amps incl connection complete all as specified and as directed

S&F of modular rotating step type electronic fan regulator, 100W /240 volts two module incl connection complete all as specified and as directed

S&F of modular socket twin type, 5 pin 6/16 Amps flush type incl connection complete all as specified and as directed

S&F modular switch type single pole one way 15/16 amps incl connection complete all as specified and as directed

S&F of dingdong call bell incl connection complete all as specified and as directed

S&F ceiling rose, surface, three terminals incl connection complete all as specified and as directed.

Supply and fixing in replacement round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete Note :- the quoted rate shall include necessary cutting of false ceiling.

Supply and fixing in replacement LED tube lights 4 feet fitting 1x 20W, 220V, Ac aluminium housing body connecting up with flexible copper conductor cable of suitable size from ceilingrose complete.

Supply and fixing in replacement LED tube lights 2 feet fitting 1x 10W, 220V, Ac aluminium housing body connecting up with flexible copper conductor cable of suitable size from ceilingrose complete.

S&F in replacement Sub main wiring with 2 runs of single core, 4 sqmm PVC insulated, unsheathed, 1100 volts grade multi-stranded, copper conductor cables (FRLS quality) drawn through PVC conduit medium grade of size 25 mm with fitting/accessories, fixed on roof, walls, ceiling etc including 4 Sqmm PVC insulated, unsheathed, single core, multistranded, copper conductor as earth continuity wire complete as specified and directed. Note : Rate includes (i) PVC conduit and its accessories (ii) Two runs of cable and one run of earth wire of size 4 sqmm and including taking down of old U/S submain

S&F in replacement of MCB SPN DB 8 way IP-43 powder painted with bus bar 100A, neutral link, earth bar and Din rail ,230 Volts with double door including taking down old unsv DB and making the surface good to match with adjucent complete all as specified and as directed

S&F in replacement of MCB SPN DB 4 way IP-43 powder painted with bus bar 100A, neutral link, earth bar and Din rail ,230 Volts with double door including taking down old unsv DB and making the surface good to match with adjucent complete all as specified and as directed

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl galvanised iron wire 4mm as earthing lead and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover , watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete.

Supply and fixing in replacement rating 240V, 10KA c curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

SP 5 To 32 AMP

SPN 32 AMP

Supply, laying/fixing on wall with clamps and testing cable in replacement XLPE Insulated , galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of LT UG cable/poles etc in soft/loose soil and getting out complete all as specified.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point for any type of excavation.

M&L for DWC pipe 50 mm dia complete for cable laying all as specified and directed

M & L for Cutting of road/hard standing and making good with PCC (1:2:4) using 20mm graded stone aggregate complete all as specified.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator, fan hook and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply & lay 25 mm dia GI pipe medium grade including all fittings fixed walls/ceiling or laid in floors/trench complete all as specified and as directed.

Supply and fix butterfly valve for following sizes 25 mm bore complete all as specified and as directed.

Cutting the existing GI pipe of any dia upto 100mm and insert a tee or mechanical joint for tapping of 25mm dia pipe line complete all as specified and directed

Agarwal Agencies (BID ID -3449992)