Balance work for C/O Ayurvedic C/O Deputy Director Veterinary Residence (Ty-V) Qtr. at Reckong Peo (SH-Building portion, WS and SI, Septic Tank, Rain water harvesting Tank, Site development and R/wall

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas all depth and all width , including getting out and disposal of excavated earth upto all leads and lifts, as directed by Engineer-in-charge. All kinds of soil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains, including dressing of sides and ramming of bottoms, upto all lift , including getting out the excavated soil and disposal of surplus excavated soil as directed, within all lead: All kinds of soil , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Excavation tranch of required width of pipes cables etc., Pipes, cables etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc., consolidation each deposited layer by ramming and watering all leads & , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Boulder filling tightly hand packed under floors, , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Centering and shuttering including strutting, propping etc. and removal of form for : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases.

Small lintels, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Edges of slabs and breaks in floor and walls

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (One Cement : three coarse sand: six graded stone) aggregate 20 mm (Twenty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (one cement : two coarse sand : four graded stone) aggregate 20 mm (twenty millimeter nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (One Cement : four coarse sand : eight graded stone) aggregate 40 mm (fory millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (one cement : five fine sand : Ten graded stone) aggregate 40 mm (Forty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., all floor level, excluding the cost of centering, shuttering and finishing: 1:5:10 (one cement :five coarse sand : ten graded stone) aggregate 40 mm (forty millimeter) nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Backfilling behind return wall, abutment wall, return wall stone boulder of size all range in the required thickness, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (one cement : two coarse sand) : four graded stone aggregate 20mm (twenty milimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg (kilogram) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene cleaning oil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Making plinth protection 50mm thick of cement concrete 1:3:6 (One cement : Three coarse sand (zone - III) : Six graded stone aggregate 20 mm (twenty milimeter) nominal size) over 75mm (Seventy five milimeter) thick bed of dry brick ballast 40 mm (forty milimeter) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (one cement : one point five coarse sand : three graded stone ) aggregate 20 mm (twenty millimeter) nominal size, in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to all level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (one cement : one point five coarse sand : three graded stone) aggregate 20 mm (twenty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (One cement : one point five coarse sand) : three graded stone aggregate 20 mm (twenty milimeter nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : cement mortar 1:6 (one cement : six coarse sand) : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level. Cement mortar 1:4 (one cement : four coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing weepholes in brick masonary /stone masonary, plain/reinforced concrete abutment, wing wall, return wall with 100mm (hundred millimeter) diameter AC pipe extending through the full width of the structures with slope of 1(V) : 20 (H) towards drawing face complete as per drawing and teechnical specification clauses 614, 709, 1204.3.7, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (twenty millimeter) nominal size upto plinth level with : Cement mortar 1:6 (one cement : six coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg) and weight of frame 58 kg). With sewer bricks confirming to IS : 4885, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 18 mm (eighteen millimeter) thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimeter) thick base cement mortar 1:4 (one cement : fou rcoarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm (square meter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm (one point twenty five milimeter) with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete : 20 mm dia (twenty milimeter diameter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick commercial board water proof shutters for up boards i/c fixing with nickel plated piano hinges with screws etc. complete), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 6mm (Six millimeter) thick water proof kit ply of standard quality ISI mark and approved shade and colour in wall linning including mitring at junctions, butt jointing and nails complete (Frame work for base to be measured & paid for separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five milimeter) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five milimeter) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five milimeter) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-inCharge, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete, Fixed to steel windows by welding, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing 40x5 mm (forty into five milimeter) flat iron hold fast 40 cm long including fixing to frame with 10 mm (ten milimeter) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm (twenty milimeter) nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 250 mm (Two hundred fifty millimeter), weighing not less than 150 gms, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 50 mm (fifty millimeter) special quality bright finished brass cupboard or ward robe locks with four levers of approved quality inculding necessary screws etc. complete, , complete as per direction of the Engineer-in-Charge.

Providing and fixing 50 mm (fifty millimeter) bright finished brass cupboard or ward robe knob of approved quality inculding necessary screws etc. complete, complete as per direction of the Engineer-in-Charge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm( seven hundred one millimeter to one thousand millimeter), with double speed adjustment with necessary accessories and screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less then AC 10 as per IS: 1868, transparent or dyed to required colour or, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

300 X 16 mm (three hundred into sixteen millimeter)

250x16mm (two hundred fifty into sixteen millimeter)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade, with necessary screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

250x10 mm (two hundred fifty into ten millimeter)

150x10mm (one hundred fifty into ten millimeter)

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not lrss than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

125mm (one hundred twenty five millimeter)

100mm (one hundred millimeter)

Providing and fixing aluminium hanging floor door stopper, ISI marked anodised (anodic coating not lrss than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete (twin rubber stopper),including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete (triple strip vertical type),including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wire gauge shutters for Steel doors, windows (shutters of standard Z-sections) and other accessories ready made standard steelwindows/ventilators with necessary fitting using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (Zero point fifty six millimeter) for doors windows including carriage of materials in all leads and lifts, as per direction of the Engineer-in-charge complete:- Side Hung Windows manufacture's specification and direction of Engineer-in-charge.

Providing and fixing 12 mm (twelve milimeter) thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm (forty milimeter) thick frame, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing water proof kit ply of standard quality ISI mark and approved shade and colour in panelling & wall linning including mitring at junctions, butt jointing and nails complete (Frame work for base to be measured &paid for separately) 12mm (Twelve millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium sheet 1 mm (one milimeter) thick in expension joints vertcally fixed with screws of nails complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing plain square edged cover fillets (beading) 50mm×12mm (Fifty millimeter into twelve millimeter) section with wood screws in Door Shutter including mitring at junction. 1st class Indian teak wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. fan clamp type I or II of 16mm dia (sixteen milimeter diameter) M.S. Bar bend to shape with hooked ends in RCC slabe or beams during laying, including painting the expose portion of loop, all as per standard desizen complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing MS BP sheet 1.66 mm (one point sixty six millimeter) to 20mm (twenty millimeter) thick in eaves board/ facia and soffit etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required: In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing MS channel iron door windows clestry window framing manufacturing frame MS section 75x40 mm (seventy five into forty milimeter) as per direction of engineering in charge and approved drawing including in hinges lock jambs beed if required angle threshold of mould steel angle 50x25 mm (fifty into twenty five milimeter) welded of rigidly fixed by mechanical means lugs with split and tails, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing angle iron door,window,clerestory window frame manufactured from steel iron section of 40X40X6mm, (Forty into forty into four millimeter) thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50X4 mm (Fifty into four millimeter) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (Two point five millimeter) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Precast terrazzo tiles 22 mm (twenty two milimeter) thick with graded marble chips of sizes upto 12 mm (twelve milimeter), laid in floors, and landing, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete , on 20mm (twenty milimeter) thick bed of cement mortar 1:4 (one cement : four coarse sand) Medium shade pigment using 50% white cement and 50% ordinary cement, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Kota stone slab flooring over 20 mm (twenty millimeter) (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) : 25 mm (twenty millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (three hundred into three hundred millimeter) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm (twenty millimeter) thick cement mortar 1:4 (One Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm (three point three kilograme/square meter including pointing the joints with white cement and matching pigment etc., complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Precast terrazzo tiles 22 mm (twenty two milimeter) thick with graded marble chips of sizes upto 12 mm (twelve milimeter), in skirting and risers of steps not exceeding 30cm in height, on 12mm (twelve milimeter) thick cement plaster 1:3 (one cement : three coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles, incliding rubbing and polishing complete with tiles of : Midium shades pigment using 50% white cement & 50% ordinarycement, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Kota stone slab 20 mm (twenty millimeter) thick in risers of steps, skirting, dado and pillars laid on 12 mm (twelove millimeter) average thick cement mortar 1:3( 1 cemrnt : 3 coarse sand) and joined with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying White glazed tiles 6 mm (Six millimeter) thick (30x20 cm) in dado in kitchen and Toilet , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 4mm thick E- Board(Embassed board), Celling of approved quality of ISI Mark including fixing to base frames with screw and clamps etc complete (frame work for base & cover fillets to be measured and paid for separately), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying factory made chamfered edge cement concrete paver blocks in footpath , parks, lawns, drive ways or light traffic parking etc. of required strength , thickness and size /shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm (fifty milimeter) thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as oer required size and pattern, finishing and sweeping extra sand, complete all as per direction of Engineer-in-charge : 80mm (eighty milimeter) thick C.C. paver block of M-30 grade with approved color design and pattern, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, (i) Single socketed 75mm (seventy five millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, (i) Single socketed pipes, 110 mm (one hubdred ten milimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten milimeter) gap for thermal expansion, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Coupler 110 mm (One hundred ten millimeter)

Single pushfit Coupler 110 mm (One hundred ten millimeter)

Single tee with door 110x110x110 mm (one hundred ten into one hundred ten into one hundred ten milimeter)

Bend 87.5° 110 mm (One hundred ten millimeter)

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimeter) dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick pre-painted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with pre-painted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 30cm wide 120cm overall semicircular plain G.I. sheet gutter with iron brackets 40×3mm (forty into three milimeter) size bolts and nuts and washers etc. including making necessary connections with drain water pipe complete as per design, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing valley 60 cm overall 0.60mm (zero point sixty milimeter) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron Jor L hooks, bolts and nuts 6mm dia (six milimeter diameter)with prepainted G.I. limpet and bitumen washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Cement plaster in single coat on rough side of brick/stone masonry for tapered plaster upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles nt exceeding 80mm (eighty milimeter) in girth and finished even and smooth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster on rough side of single or half brick wall of mix: 1:6 (one cement: six coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6 mm (six millimeter) cement plaster of mix 1:3 (1 cement : 3 fine sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Finishing walls with textured/Heritage exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @2.20kg/10 sqm., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete : 125 mm (one hundred twenty five milimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm( fifteen into twenty two centimeter) in cement mortar 1:6 (One Cement : Six Sand) and inside plastring with cement plaster 1:3 (One Cement:Three Sand) including earth work and laying 10 cm (ten centimeter) cement concrete in 1:5:10 (One Cement : five Sand : ten graded stone aggregate) of 40 mm nominal size) and 7.5 cm (seven point five centimiter) cement concrete 1:2:4 (One Cement : Two Sand : Four Graded stone aggregate of 20 mm (twenty milimeter) nominal size) and finished with a floating coat of neat cement complete as per standard design, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing MS railing for stair case having balluster of 19mm x 19mm (ninteen into ninteen milimeter) squre bar with a clear height of 85cm (eighty five centimeter) embedded in cement concrete steps and jointed with electrical/gas welding at top along with MS flat of 40mm x 40mm (forty into forty milimeter) size complete with a applying priming coat of red led paint as per drawing specifiction, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing, cement compound consisting of applying: after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. third layer of 1.5 mm (one point five milimeter) thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm (six milimeter) thick hard board backing : Rectangular shape 1500x450 mm (fifteen hundred into four hundred fifty milimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (hundred milimeter) sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimeter) with integral type foot rests, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 (ten) litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm (forty millimeter) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimeter) C.P. brass pillar taps, 32 mm thirty two millimeter) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm( five hundred fifty into four hundred milimeter) with a pair of 15 mm (fifteen millimeter) C.P. brass pillar taps, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm (forty milimeter) including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board, 510x1040 mm (five hundred ten into one thousand forty milimeter) bowl depth 178mm (one hundred seventy eight milimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm (fifteen milimeter) nominal bore. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm (forty millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimeter) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600x120x5 mm (six hundred into one hundred twenty into five millimeter) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (forty millimeter) long screws, rawl plugs etc., complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing toilet paper holder : C.P. brass, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipe ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110 mm (One hundred ten millimeter) diameter

75 mm (Seventy five millimeter) diameter

Providing and fixing PVC clamps ISI marked of approved design with steel screw and rawal plugs etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110 mm (One hundred ten millimeter) diameter

75 mm (Seventy five millimeter) diameter

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110 mm (One hundred ten millimeter) diameter

75 mm (Seventy five millimeter) diameter

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110 mm (One hundred ten millimeter) diameter

75 mm (Seventy five millimeter) diameter

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110 mm (One hundred ten millimeter) diameter

75 mm (Seventy five millimeter) diameter

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

110 mm (One hundred ten millimeter) diameter

75 mm (Seventy five millimeter) diameter

Providing and fixing PVC Cowl, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

75mm (Seventy five milimeter)

110mm (One hundred ten milimeter)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors, 110 mm (One Hundred ten millimeter) inlet and 75 mm (seventy five millimeter) outlet, Sand Cast Iron S&S as per IS- 3989, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 100mm (Hundred millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour, 600 mm (six hundred millimeter) long towel rail with total length of 645 mm (six hundred forty five millimeter), width 78 mm (seventy eight millimeter) and effective height of 88 mm (eighty eight millimeter), weighing not less than 190 gms (one hundred nintey grames), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge, Concealed work, including cutting chases and making good the wall etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

1216 (16 mm (sixteen milimeter) OD) pipe

1620 (20 mm (twenty milimeter )OD) pipe

2532 (32 mm (thirty two milimeter )OD) pipe

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15 mm dia ( fifteen millimeter diameter) nominal bore,

20 mm dia ( twenty millimeter diameter) nominal bore,

32 mm dia ( thirty two millimeter diameter) nominal bore,

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm (twenty five to forty millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) 200 mm (two hundred milimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

25 mm (twenty five milimeter) nominal bore

32 mm (thirty two milimeter) nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm (fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm (thirty centimeter) length, 15 mm (fifteen millimeter) nominal bore, for wash basin including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (one cement : four coarse sand) for sluice valve, with C.I. surface box 100x100x75mm (hundred into hundred into seventy five milimeter) (inside) with hanged cover fixed in cement concrete slab 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimeter) nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (one cement :five fine sand : ten graded stone aggregate 40 mm (forty milimeter) nominal size) and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12 mm (twelve milimeter) thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15 mm (fifteen millimeter) nominal bore

20 mm (twenty millimeter) nominal bore

32 mm (thirty two millimeter) nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931, 15mm (fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass long nose bib cock Cat no. CON 107 KN jagur or equivalent single control of approved quality conforming to IS standards. 15 mm (fifteen milimeter) nominal bore , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT pillar cock of approved quality and colour.15 mm (fifteen millimeter)nominal bore, 107 mm (one hundred seven millimeter)long,weighing not less than 110 gms including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimeter ), breadth 102mm (one hundred two millimeter), height of 75mm (seventy five millimeter with concealed fitting arrangements, weighing not less than 106 gms including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :150 mm diameter S.W. pipe including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete, including testing of joints etc. complete: 250 mm dia R.C.C. pipe, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm (Hundred milimeter) diameter and 1.20 m long complete as per standard design, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality, L D- 2.5, Circular shape 450 mm (450 milimeter) internal diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing masonry chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 ( one cement :four coarse sand) for fire hydrants, with C.I surface box 350x350mm (three hundred fifty into three hundred fifty) top and 165 mm (one hundred sixty five) deep (inside) with chained lid and RCC top slab 1:2:4 mix ( one cemnt :second coarse sand :four graded stone aggregate 20 mm (twenty milimeter) nominal size), i/c necessary excavation, foundation concrete 1:5:10(one cement :five fine sand : ten graded stone aggregate forty mm nominal size) and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12mm (twelve miimeter) thick finished with a floatering coat of neat cement complete as per standard design: With common burnt clay F.P.S. ( non modular) bricks of class designation 7.5, as per PWD Specifications and as per direction of Engineer in charge.

Man mohan thakur

SURENDER KUMAR NEGI CONTRCATOR

SANJEEV KUMAR CONTRCATOR