SPECIAL REPAIRS TO BLDG NO. 136 MUSEUM GRC KAMPTEE.

Amount

Taking down cement plaster, any description, thickness including raking out joints hacking out for key, scrubbing down with water etc complete all as specified and directed.

Material & labour for Rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth (without using extra cement) , complete all as specified and directed.

M & L for rendering 10 mm thick on brickwork in cement mortar (1:4) finished even and smooth without using extra cement, complete all as specified and directed.

Material & labour rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM 1:3 with putty finish as in ceiling finished even & smooth (without using extra cement), complete all as specified and directed.

Material & labour for Rendering 15 mm thick on brick or concrete surfaces in CM 1:4 using water proofing compound as per manufacturer instructions, and finished even & smooth (without using extra cement), complete all as specified and directed.

Material & labour for preparation of newly plastered surfaces of wall & applying two coats of oil emulsion over alkali resistant priming paint, over a coat of wall care putty, complete all as specified and directed.

Material & labour for preparation of old plastered surfaces of wall & applying two coat of oil emulsion,over a coat of alkali resistant priming paint including complete removal of existing treatment, complete all as specified and directed.

Material & labour for preparation of newly plastered surfaces of wall & applying two coats of Apex weatherproof emulsion over a coat primer, complete all as specified and directed.

Material & labour for preparation of newly plastered surfaces of celing & applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Material & labour for preparation of old plastered surfaces of celing & applying two coats of oil emulsion over a coat of primer including complete removal of existing treatment, complete all as specified and directed.

Demolition of stone slabs and roof tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc. Including removal of waterproofing treatment below the tiles, complete all as specified and directed.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness, below or anove ground level, complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n exc 63mm, deposited, spread and levelled in layers n. exc 15cm thick, watered and rammed to a true surface, complete all as specified and as directed.

M & L for PCC 1:3:6, type C2, (using 20mm graded stone aggregates) as in plinth protection, surfaces finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for forming contraction (dummy) joints 50mm deepx10mm wide, filled with sealing componud grade 'B', complete all as specified and as directed.

M & L for Machine cut kota stone slab flooring 20mm thick over 20mm thick cement screed base laid and jointed with grey cement slurry in CM 1:4 mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

M & L for Kota stone slab 20mm thick in riser of steps, skirting, dado and pillar laid over 10 mm cement screed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.

Supply only Liquid integral Water proofing compound. Complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame) complete all as specified and directed.

Supply and fix Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and directed.

Supply and fix Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc., complete all as specified and directed.

Supply and fix Framed work Fe 290(Gde E-165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing , complete all as specified and directed.

Supply and fix 35 mm thick,IInd class hard wood, plain framed panelled shutters any number of panels with lock rail and panels of timber flat on both side, feather, edged or of venered particle board, medium density, wood particle board with commercial face veneers, complete all as specified and directed.

M & L for preparations of new wood or wood based materials of any descriptions not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M & L for preparations of old wood or wood based materials of any descriptions not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Cutting holes in brick walls exc half brick but n.exc one brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 , complete all as specified and directed.

Supply & fix 125 mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 etc, complete all as specified and directed.

Supply & fix 300 mm long aluminium alloy, anodised, sliding bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and as directed.

Supply & fix 200 mm long aluminium anodised, barrel tower bolt of extruded section, complete all as specified and directed.

Supply & fix 150 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and directed.

Supply & Fix floor door stopper 140mm length of cover plate of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Supply and fix sheet glass 5.00 mm thick ordinary quality and glazing with oil putty or glazing pins/ spring clips exc, 0.5 sqm in each frame, complete all as specified and directed.

Hacking out old broken glass of (any thickness, size and quality) from metal frame including punching or drilling out old glazing pins / spring clips and providing and fixing new ones etc complete all as specified and directed.

Supply and fix sheet glass frosted, ordinary quality, 4 mm thick and glazing with oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

Supply and fix tinted sheet glass, ordinary quality, 4 mm thick and glazing with oil putty in square exc. 0.50 Sqm in each pane complete all as specified and directed.

Preparation of old painted surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel (ordinary tint) (each coat) over a coat of red oxide complete all as specified and directed.

Hydraulically pressed burnt clay tile plain of size 200x200x15 mm fixed by using cement paste and slurry as required, complete all as secified and as directed by Engr-in-charge.

Terrace waterproofing M & L for Providing and carry out waterproofing treatment to sound concrete surface includes proper surface preparation to remove loose dust, dirt, loose mortar, curing compound etc., carry out cementitious injection grouting at leakage points and construction joints using cement slurry modified with Cebex 100-Plasticised expandive grout admixture, open construction joint in 10x10 mm size, filling the same using Polymer Modified , treatment of construction joints using polymer modified mortar prepared by using Nitobond SBR Latex- screed modifier cum bonding agent Repair mortar, application of polymer modified vatta at floor-wall junction and final application of two coats of Nitocote CM 210 – Elastomeric Waterproofing coating coverage as per technical datasheet etc. complete including all tools and tackles as per manufacturer’s specification.. Coating shall be approved under UK Water Byelaws Scheme, shall be having resistance to positive water pressure – 5 Bars(50 meter) (DIN 1048)Pt 5, negative water-pressure of 3 Bars (30 meter),static crack accommodation of 0.9 mm. sprinkle sieved coarse sand on wet surface of final coating for better adhesion of plaster or screed incl necessary scaffolding, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE. (ii) Guarantee of 05 years should be given by contractor.

M & L for 20 mm thick cement plaster in two layers (10mm+10mm) in CM 1:3 finished even & smooth w/o using extra cement by mixing liquid WPC in both layers over Nitocote CM 210 or equivalent as approved over protective layer incl necessary scaffolding, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE. (ii) waterproofing should be measured and paid seperately)

Tile Cleaning M & L for Providing and applying Reebaklen- Concrete remover, cleaning and etching agent, a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear blue solution,in 1,5 and 20 litre, having specific gravity 1.08 at 25ºC, used for the removal of mortar and plaster runs, droppings and stains from brickwork, concrete surfaces, removal of hardened concrete from tools, machinery and equipment, or rust and mill scale from steelwork. Typical application includes mixing of Reebaklens with water in ratio between 1:1 and 1:4 (Reebaklens cleaning agent to water), apply with stiff bristle broom, brush the affected areas and wash down thoroughly with clean water incl necessary scaffolding.etc complete, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE.

Tile grouting (3mmx3mm) Supplying and filling Nitotile Grout –Hygienic, hard wearing stain free to tiles joints after minimum 24 hrs of tile fixing, proper cleaning of tile joints free from dust, dirt, mortar etc. 1 Kg pack of Nitotile Grout powder shall be mixed with 300 ml of potable water to get lump free, uniform, thick creamy paste and apply the same between the tiles using a sponge or a small piece of cloth, work the mixture around the joints and around the edges, remove the surplus material from the face of the tiles with a dry cloth and run the tip of a gloved finger or suitable rounded tool along the grout to level if off and form a profile etc. complete as per EIC. Nitotile Grout shall be having specific gravity of 1.9-2.0 g/cc, working time – 30 mins at 35 °C ,Compressive strength (ASTM C109)-38 Mpa at 28 days, Tensile Strength (BS 6319:Pt 7): 3 N/mm2 at 28 days incl necessary scaffolding, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE. (ii) Guarantee of 02 years should be given by contractor.

Tile grouting (10mmx3mm) Supplying and filling Nitotile Grout –Hygienic, hard wearing stain free to tiles joints after minimum 24 hrs of tile fixing, proper cleaning of tile joints free from dust, dirt, mortar etc. 1 Kg pack of Nitotile Grout powder shall be mixed with 300 ml of potable water to get lump free,uniform, thick creamy paste and apply the same between the tiles using a sponge or a small piece of cloth, work the mixture around the joints and around the edges, remove the surplus material from the face of the tiles with a dry cloth and run the tip of a gloved finger or suitable rounded tool along the grout to level if off and form a profile etc. complete as per EIC. Nitotile Grout shall be having specific gravity of 1.9-2.0 g/cc, working time – 30 mins at 35 °C ,Compressive strength (ASTM C109)-38 Mpa at 28 days, Tensile Strength (BS 6319:Pt 7): 3 N/mm2 at 28 days incl necessary scaffolding, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE. (ii) Guarantee of 02 years should be given by contractor.

Supplying and filling Nitotile Grout –Hygienic, hard wearing stain free to tiles joints after minimum 24 hrs of tile fixing, proper cleaning of tile joints free from dust, dirt, mortar etc. 1 Kg pack of Nitotile Grout powder shall be mixed with 300 ml of potable water to get lump free, uniform, thick creamy paste and apply the same between the tiles using a sponge or a small piece of cloth, work the mixture around the joints and around the edges, remove the surplus material from the face of the tiles with a dry cloth and run the tip of a gloved finger or suitable rounded tool along the grout to level if off and form a profile etc. complete as per EIC. Nitotile Grout shall be having specific gravity of 1.9-2.0 g/cc, working time – 30 mins at 35 °C ,Compressive strength (ASTM C109)-38 Mpa at 28 days, Tensile Strength (BS 6319:Pt 7): 3 N/mm2 at 28 days incl necessary scaffolding, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE.

M & L Water repellent Coating Providing and application of protection system to external stone surface after proper surface preparation and cleaning to remove any laitance, algae, fungal, foreign materials using suitable repairing method followed by uniform application of Nitocote SN522- Colourless, ready to use, silicone resin solution using suitable brushing or spraying at recommended coverage etc. minimum 2 coats recommended, complete including all tools and tackles as per manufacturers specification and as directed by EIC incl necessary scaffolding, all as per Particular Specification and as directed by Engr-in-Charge. Note: (i) The item will be executed through manufacturer or their authorized applicator, as approved by GE. (ii) Guarantee of 02 years should be given by contractor.

Supply and fix Dholpur stone cladding 16 to 18mm , gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.5 sqm area fixed with and including one number SS clamps (grade-202) of flat 30mmxx 2mm, 150 mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment, complete all as specified and directed

Demolition of brick work or stone/boulder masonry built in cement mortar including ashlar facing dressed stone and pre-cast concrete articles, complete all as specified and directed

M&L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 (Using old size brick) complete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4, complete all as specified and directed.

M & L preparation of old plastereed surfaces and applying two coats of cement base paint, complete all as specified and directed.

Demolition of PCC in any position not otherwise specifically provided for as in drain, complete all as specified and directed.

M & L for PCC (1:4:8) Type D2 (using 40 mm graded stone aggregates ) as in foundation concrete and mass filling, complete all as specified and directed.

M&L PCC (1:2:4) type B-1 (using 20mm graded stone aggregated) as in coping, complete all as specified and directed.

M & L for Cement concrete in surface channels and drains Type B2 1:2:4 (using 20 mm graded aggregate), complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc, complete all as specified and directed.

M&Lcolor vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exc 0.18 sqm but not exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in 15mm thick screed bed in CM 1:4 & neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

Ditto all as per item No. 56 above, but in skirting / dados incl screed base plaster 10mm thick in CM 1:4 finished even and fair, complete all as specified and directed.

Material & labour for glazed ceramic coloured tiles (300mmx450mm, on vertical surface such as skirtings/dados set and jointed in neat cement slurry and pointed in coloured cement to match and incl.10mm thick backing coat in CM 1:4 finished even and fair, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Supply & Fixing Marble slabs 16-18mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types, complete all as specified and directed.

Supply & Fixing Granite (of any type)slab 16-18mm thick machine cut, bedded with 15mm thick screed bed in CM 1:4 and jointedwith grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types, complete all as specified and directed.

Supply and fix Aluminium (extruded section body) Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg , complete all as specified and directed.

Supply and fix 2 levers brass mortice lock, vertical type, size 100mm, complete all as specified and directed.

Material & labour for preparation of old plastered surfaces of wall & applying 2 coatS of Apex weatherproof emulsion, complete all as specified and directed.

Material & labour for preparation unplastered surfaces & applying 2 coat of Apex weatherproof emulsion over roof tiles, complete all as specified and directed.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.9,500.00 /- ]

chronicle enterprises

S D WAGHAMSHI

Bidder Name

S D WAGHAMSHI

chronicle enterprises

AK CONSTRUCTION