Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹18.1 LAccepted-AOC VILL TUTNYU PO PS LAZU KHONSA DISTRICT TIRAP PIN 792130 ARUNACHAL PRADESH | KHONSA | TIRAP | ARUNACHAL PRADESH | 792130 | L1 | Accepted-AOC DUE TO L1 RATE | |
| 2 | L2₹19.1 L+₹67,849.50 (3.69%)Rejected-Finance AT MAIN ROAD DANDAI PO PS DANDAI DIST GARHWA | LATEHAR | JHARKHAND | 822112 | L2 | Rejected-Finance DUE RATE IS HIGH | |
| 3 | L3₹21.8 L+₹3.4 L (18.7%)Rejected-Finance | L3 | Rejected-Finance DUE RATE IS HIGH | |
| 4 | L4₹22.8 L+₹4.4 L (23.9%)Rejected-Finance | L4 | Rejected-Finance DUE RATE IS HIGH |
Tender Value
₹18.7 L
EMD Value
₹37,400
Closing Date
16 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Lekhapani
GE Lekhapani, Tinsukia, Assam
ADDN/ALTN AND IMPROVEMENT OF BLDG NO.T-22 AND REPLACEMENT OF ROOF SHEET WITH GALVALUME SHEET IN BLDG NOS T-25 and T-26 AT LEKHAPANI MIL STN
2022_MES_552716_3
8694/E8
Open Tender
Miscellaneous Works
Item Rate
180 days
GE Lekhapani
Class E Category a(I)
4 documents required · 4 mandatory
₹500
GE Lekhapani
₹37,400
Yes
13 Jan 2023
24 Nov 2022
19 Dec 2022
24 Nov 2022
16 Dec 2022
2 Dec 2022
Amount
Dismantling of plain or corrugated steel sheeting any guage, thickness including Nanital or similar pattern roof coverings complete and making good the disturbed surfaces complete all as specified and as directed.
Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including frames and cover fillets complete all as specified and directed.
Taking down roof trusses, coupled rafters or trussed beams of clear span above 4 mtrs and upto 8 mtrs complete all as specified and directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
Dismantling timber scantlings in unframed timber work 40 sq.cm and over in section, in any position complete all as specified and as directed.
Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles and removing debris beyond the premises complete all as specified and directed.
Demolition of unreinforced cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing debris beyond the premises complete all as specified and directed.
Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm each and making good to disturbed surfaces complete all as specified and as directed by the Engineer-in-Charge.
Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4.0sqm each and making good to disturbed surfaces complete all as specified and directed by the Engineer-in-Charge.
M&L for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed
M&L for hot dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550MPa as in ridge/valley/gutter/eaves boardings fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.
M&L Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605mm x 605mm in true horizonatal level, hot dipped galvanised steel sections consisting of main “T” runner with suitably spaced joints to get required length and size 24mm x 38mm made from 0.30mm thick (Min) sheet spaced at 1200mm centre to centre and cross “T” of size 24mm x 28mm made of 0.30mm thick (Min) sheet, 1200mm long spaced between main “T” at 600mm centre to centre to form a grid of 1200mm x 600mm and secondary cross “T” of length 600mm and size 24mm x 28mm made of 0.30mm thick (Min) sheet to be interlocked at middle of the 1200mm x 600mm panel to form grids of 600mm x 600mm and wall angle of size 24mm x 24mm x 0.4mm. Main “T” runner to be suspended from purlins or truss member using 2 to 3 mm dia GI wire, 1200mm x 600mm centre to centre all complete for all heights as per specifications and as directed by Engineer – in - Charge.
M & L for 4 mm thick high pressure, oceanic pre-primed, self embossed, non asbestos fibre cement decorative board, water, termite and fire resistant for insulation ad acoustic purpose to be placed in grid system hold down clips with provision of high fixtures, air conditioning, diffuser and ducts, sprinkler, smoke detector etc, complete all as per manufacturer instructions
Fixing only roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Note : Item obtained from dismantling shall be reused after cleaning the rusted surfaces cut to size and fabricated as per site requirement complete all as specified and as directed by Engr-in-charge.
M&L for preparation of old painted surfaces of steel of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.
S&F Mild Steel work in tubular trusses (square/rectangular/circular) hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 4923 grade St 240 complete all as specified and directed.
S&F Mild Steel work in tubular Column (square/rectangular/circular) hollow section including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161 grade St 240 complete all as specified and directed.
M&L Preparation of new or previously un treated steel surfaces of any description, over 10 cm width or girth, not otherwise described and evenly applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.
M & L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations bed concrete, filling and mass concrete complete all as specified and directed.
M & L Brick work with subclass “B” Old size bricks, straight or curved on plan,exceeding 6 m mean radius, built in CM (1:6) complete all as specified and directed.
M&L brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m radius built in CM (1:4) complete all as specified and directed.
M&L Brick work with sub class old size 'B' bricks, straight or curved on plan to any radius, built in CM (1:4) as in half brick thick walls complete as specified and directed.
Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.
S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
All as per Item No.24 above,but 6mm to 8 mm dia complete all as specified and directed.
All as per Item No.24 above,but 5 mm dia and over upto and including 10 mm dia in stirrups, spacrs and binders,etc complete all as specified and directed.
M&L Providing RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in as in beams, cantilevers beressummers lintels over 1.5m length and the like etc complete all as specified and directed
M&L Rendering 10.mm thick plaster in CM (1:6) on fair faces of brick work or concrete surfaces including finishing top even and smooth without using extra cement complete all as specified and directed.
M&L Rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surfaces including finishing fair and even complete all as specified and directed.
Supply only Integral water proofing compound of approval brand complete all as specified and directed.
M&L Preparation of new plastered surfaces of wall and preparing surfaces as directed by applying thin layer of exterior wall care putty of minimum 1mm thick and applying two coats of cement base paint over a coat of primer complete all as specified and directed.
M&L Preparation of new plastered surfaces of wall and preparing surfaces as directed by applying thin layer of wall care putty of minimum 1mm thick and finally applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.
M&L Preparation of newly plastered surfaces on walls and applying three coats of white wash complete all as specified and as directed.
M&L Preparation of old painted or plastered surfaces of walls etc by washing, rubbing down and applying one coat of cement base paint complete all as specified & directed.
S&F Pressed steel frames (125 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.
S&F Pressed steel frames (105 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.
M&L PCC (1:3:6), type C-1, (using 20mm graded crushed stone aggregates) as in bed block, blocks for holdfasts, filling in pressed steel door frames , benching slightly rounded or chamfered angles & throating etc including necessary use & waste of form work complete all as specified and directed.
S&F 30 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides & both face is covered with decorative face veneer with lipping / frame to match & fixed to chowkats complete all as specified & directed.
S&F 35 mm thick, hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified & directed.
S&F Stainless steel wire cloth of 0.36mm nominal dia of wire and average dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.
S&F 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.
S&F 150mm size aluminium handles, cast type, anodized and fixed complete all as specified & as directed.
S&F 300mm length of bolt, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & as directed.
M&L for prparing new wood & wood basd surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.
S & F for aluminum powder coated (powder coated of required colour) three track sliding windows frame top & sides of size 92 x 31.75 x 1.30mm (section No 20621) bottom of size 92 x 31.75 x 1.30mm (Section of 20620) and shutter top & bottom of size 40 x 18 x 1.29 (section 20846) and lock side shutter frame of size 40 x 18 x 1.29mm (Section 20845) with rebbuer gasket, beading and locking arrangement with and including stainless steel wire mesh 0.36mm nominal dia with 1.40mm average aperture and fixing 4 mm thick glass with necessary rubber beading gasket etc complete all as specified and directed.
S&F Framed work such as griils, grating, angle iron door frames etc., with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, laders, framed balusters, walk ways, railings frame work of water tanks and similar work conforming to Fe-290. Gde E-165 complete all as specified and directed.
M&L PCC (1:2:4), type B1, (using 20mm graded crushed stone aggregates) as in bed block, blocks for holdfasts, coping , benching slightly rounded or chamfered angles & throating etc including necessary use & waste of form work complete all as specified and directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all complete all as specified and directed.
M&L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and directed.
M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes complete all as specified and directed.
M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm as in vertical surfaces such as skirting,dado, etcs, and set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM (1:4) complete all as specified and directed.
Dismantling of timber framed scantling under 40 Sqcm as in fillets, rails, posts, rafters purlins etc complete all as specified and directed.
Dismantling boarding any description fixed in any position complete all as specified and directed.
Excavating in post holes (or similar holes) in any type of soil each not exceeding 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm ,watering and removing surplus soil to a distance not exceeding 50m and making good surface (soft /loose soil) complete all as specified and directed.
M & L Second class clean swan hard wood as in scantlings to replace old and decayed timber (including piecing, scarfing, etc of old and new timbers if required) and removing defective portions to store complete all as specified and directed.
M & L Second class clean swan hard wood as in scantlings complete all as specified and as directed
M & L Preparing surfaces of wood and wood based materials, new or old of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and as directed
S & F Band, straps, supports or stays clamps,hold fasts, wall ties, hooks for securing purlines to wood trusses or raftgers, knee pieces two way and three way strps plate washers and similar small articles conforming to FE 290 Gde E-165 complete all as specified and directed.
S&F Rolled mild steel Plates (plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, with out any attachment conforming to Fe:410-W(Gde-E-250) quality-A complete all as specified and directed.
S & F Mild steel bolts with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long and diameter of neck exc 12 n.exc 20 complete all as specified and directed.
M&L for cutting chases for inserting GI tubing in walls, floor etc and making good complete all as specified & directed.
S&F 15mm dia bore of pipes, medium grade, galvanised iron, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified & directed.
S&F fancy type long body15 mm dia bib taps cast copper alloy, chromium plated screwed down to iron pipe or for brass ferrule & fixed complete all as specified & directed.
S&F PVC (SWR) pipes 75mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.
S&F PVC (SWR) bend and radius 75 mm bore fixed with pipe complete all as specified and as directed.
S&F PVC (SWR) 'S' trap and radius 110 mm bore fixed with pipe complete all as specified and as directed.
Taking down copper/aluminium point wiring, (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.
M&L for concealed point wiring with two run x 1.5 sqmm, FRLSH PVC insulated, unsheathed, multistranded single core copper conductor cable with ISI marked for working voltage 1100 volt grade, drawn in and including PVC conduit medium grade not less than 20 mm dia ISI marked with necessary fixing acessories concealed in wall and fixed on roof as applicable, including 1.5 sqmm , FRLSH PVC insulated multistranded copper conductor of ISI standard as earth continuity conductor and connecting to earth dolly and to be terminated in and inclusive of 1.6 mm thick sutable size MS box and laminated hylum sheet of 3 mm thickness ISI marked for mounting switches, socket out lets, regulator etc for one light point controled by one one way 5 Amp switch,complete all as specified and directed by Eng-in-charge.
All as per Item No.68 above,but one fan point controlled by one, one way 5 Amp switch complete all as specified and directed.
All as per Item No.68 above,but one 5 pin socket outlet 05 Amp on independent board complete all as specified and directed.
All as per Item No. 68 above,but one 5 pin socket outlet 05 Amp on same board with other switches
All as per item No 68 above,but for one 15 Amps socket outlet but using copper conductor of size 2.5 sq mm, PVC insulated single core cable complete all as specified and directed.
S&F LED tube light fitting 4 ft. 1 x 18 watt with 230 volts, with bipin holder connector block, LED retrofit tube rod etc complete with all accessories internally pre-wired and fixed to walls/ceiling with screw on and incl 2 Nos x round PVC blocks including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.
S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.
Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed.
S&F Fan regulators electronic stepped type complete all as specified and directed.
S&F Switch piano flush type, 6 amps, 230V AC,single pole, one way complete all as specified and directed.
S&F Switch socket combination multipurpose suitable for 2 pin and 3 pin 6 amp flush type complete all as specified and directed.
S&F Switch socket combination multipurpose suitable for 2 in 1 , 3 pin 5 & 15 amps flush type complete all as specified and directed.
S&F socket outlet type 2 in 1 3/5 pin 5 Amps with other switches complete all as specified and directed.
S&F Ceiling rose, 3 terminals, surface bakelite, PVC/Polycarbonate complete all as specified and directed.
M & L Sub main wiring complete with 2 runs of 6 sq mm, FRLSH single core, PVC insulated, unsheathed cable,1100 volts grade,multi standard with copper conductor drawn through and including PVC conduit of size not less than 20mm medium grade and concealed in wall / floors etc., with one run of PVC insulated 6 sq mm FRLSH multi-stranded copper conductor for earth continuity conductor including taking down old US wiring all as specified and directed. Note :- Three runs of 6 sqmm copper cable and one run of conduit shall be measured as one unit length.
S & F MCB SP 6 to 32 Amps 240 volts complete all as specified and directed.
S & F MCB SPN 6 Amps to 32 Amps 240 volts complete all as specified and directed.
S&F Single pole and neutral DB wall mounting type,240 Volts, 8 Way with 200 Amps rated bus bar,double door suitable for fixing MCB's including connecting etc and taking down un serviceable DB ,main switch complete all as specified and directed.
M&L Earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6 mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick pre-cast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways,etc and testing on completion complete all as specified and directed by Engineer-in-Charge.
S&F LED bldg security light fitting 48W watt with 230 Volts with IP 66., high Impact resistance complete with all accessories internally pre-wired and fixed to walls on suitable size GI pipe bracket with two Nos of clamp set size MS flat 40x3mm including drilling holes made to shape and provn of suitable size nuts/bolts/washers and connection complete all as specified and directed.
S & F Fan hooks made of MS clamp deformed to proper shape including nut & bolts and drilling/cutting roof as required at site and fixing fan hook with existing steel reinforcement all as directed by Engr-in-charge.
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .