Electrical and mechanical works along with laying and fitting of departmental rising main to be carried out at WSS Sadatpora Stage 1st and 2nd under JJM

Amount

Providing, fitting, installation, testing and commissioning of VT pumping unit of following specifications: A. PUMP 1. Discharge = 10000 GPH 2. Type = Self water lubricated, VT pump, open line shaft. 3. Liquid to be handled = Raw Water 4. RPM = 1460 5. Head = 25 Meters 6. Efficiency = Not less than 75% B. Prime Mover 1. Type = Vertical hollow shaft, AC induction 2. Power Supply = 03 Phase, 41 5V± 10% AC 3. Frequency = 50Hz±3% 4. RPM = 1450 Synchronous 5. Efficiency = Not less than 85% 6. HP = Corresponding to Head and discharge but not less than 10HP. Rest of Specification/Details are as per clause 6 of Annexure "C" of SBD for stage 1st

Providing, fitting, installation, testing and commissioning of VT pumping unit of following specifications: A. PUMP 1. Discharge = 10000 GPH 2. Type = Self water lubricated, VT pump, open line shaft. 3. Liquid to be handled = Clear Water 4. RPM = 1460 5. Head = 95 Meters 6. Efficiency = Not less than 75% B. Prime Mover 1. Type = Vertical hollow shaft, AC induction 2. Power Supply = 03 Phase, 41 5V± 10% AC 3. Frequency = 50Hz±3% 4. RPM = 1450 Synchronous 5. Efficiency = Not less than 85% 6. HP = Corresponding to Head and discharge but not less than 30HP. Rest of Specification/Details are as per clause 6 of Annexure "C" of SBD for stage 2nd

Providing, fitting, installation, testing and commissioning of VT pumping unit of following specifications: A. PUMP 1. Discharge = 10000 GPH 2. Type = Self water lubricated, VT pump, open line shaft. 3. Liquid to be handled = Clear Water 4. RPM = 1460 5. Head = 75 Meters 6. Efficiency = Not less than 75% B. Prime Mover 1. Type = Vertical hollow shaft, AC induction 2. Power Supply = 03 Phase, 41 5V± 10% AC 3. Frequency = 50Hz±3% 4. RPM = 1450 Synchronous 5. Efficiency = Not less than 85% 6. HP = Corresponding to Head and discharge but not less than 25HP. Rest of Specification/Details are as per clause 6 of Annexure "C" of SBD for stage 2nd old sadatpora

Providing/supplying and fitting of G.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-C confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) for Y junction Size : 100 Class: C (Heavy) Rest of Specification as per clause 8 of Annexure "C" of SBD for stage 1st and 2nd

Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seated glandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units . Size: DN100 PN:1.6/16 Rest of Specification/Details are as per clause 12 of Annexure "C" of SBD for stage 1st and 2nd

Providing and fitting of Ductile Iron double flanged, Slanted seat swing check valve( NRV) as per IS 5312. Size: 100mm PN: 1.6/16 Rest of Specification/Details are as per clause 13 of Annexure "C" of SBD for stage 1st and 2nd

Providing, fitting, testing and commissioning of Manually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::30KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of Annexure "C" of SBD. for stage ist

Providing, fitting, testing and commissioning of Manually operated copper wound, 3-phase, AC power supply multi step voltage stabilizer. Rating::50KVA Manufacturers test certificate to be apended and rest of specification as per clause 44 of Annexure "C" of SBD. for stage 2nd

Creation of pole mounted , outdoor type Electric Sub Station by way of S/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum wound Specifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Type of cooling: ONAN. Rating: 63 KVA HT Transformer, 3 phase (Level 2). Manufacturers certificate be apended and rest of specification as per cluase 26 of Annexure "C" of SBD for stage ist and 2nd

Supply, installation, erection of 9 mtrs long H.T pope of specifications ST410 (SP-33). The job further includes drilling of holes for installation of various accessories .wherever required the job further includes G.I wire earthing of pole as per REC standard. as per Clause 32 of Annexure "C" of SBD for stage 1st & 2nd

Cement Bottoming 1:2:4 mix as per REC standards 0.5 cum/pole

Providing and fitting G.I Channel /Angle/ Flat /Riser of sizes including clamps as per Clause 27 of Annexure "C" of SBD for stage 1st & 2nd

Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, single break provided with locking arrangement at both ON and OFF position consisting of HT post double insulator, copper or copper alloy high pressure heavy contact assembly, rod with bearings , operating handle and 2 length of 32mm dia. GI pipe conforming to IS 1818 1961, 06 No. of insulators, rated voltage 11KV 200A complete as per IS specs. as per Clause 28 of Annexure "C" of SBD for stage 1st & 2nd

Supply, Installation, Testing and commissioning of 11KV polymer fuses Set Horn Gap 3-phase 200 A suitable for vertical installation. as per Clause 29 of Annexure "C" of SBD for stage 1st & 2nd

Supply, Installation, Testing and commissioning of Gapless Surge arrestor station class, 10KA, 9KV, LA With polymer housing, Station Type as per Clause 30 of Annexure "C" of SBD for stage 1st & 2nd

Supply and fitting of 11 KV polymeric composite pin insulator 12 KV, 5KN, Lighting impulse 75KV Positive, and 80 KV Negative , creepage distance 320 mm as per Clause 31 of Annexure "C" of SBD for stage 1st & 2nd

Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each) as per Clause 61 of Annexure "C" of SBD for stage 1st and 2nd

Painting of poles Red oxide as per Clause 37 of Annexure "C" of SBD for stage 1st & 2nd

Painting of poles Aluminum paint as per Clause 38 of Annexure "C" of SBD for stage 1st & 2nd

P/I of earthing station for electric substation, LT panel and stabilizer comprising of company fabricated earthing electrode as per IS: 3043 as per Clause 48 of Annexure "C" of SBD for stage 1st and 2nd

P/L of ACSR conductor of size 0.05 as per the relevant IS standard as per clause 78 of Annexure "C" of SBD for stage 1st & 2nd

Providing and fitting of 3”x5/8” Galvanized nuts and bolts

Providing and fitting of LT Distribution box for H.T transformer with MCCB For incomer and SFU for outgoing circuits as per clause 42 of Annexure "C" of SBD for stage 1st & 2nd

Distribution Cables: Providing, Installation, testing of multi-stranded copper conductor PVC insulated single core unsheathed 35mm sq. Copper cable for internal distribution wiring for stage 1st & 2nd as per clause 67 of Annexure "C" of SBD

Fabrication Providing and fitting of modular control panel as . THE technical details/ Ratings of various components of Modular Control Panel are given Below a. Main Circuit Breaker (Incommer MCCB) of rting = 160-200Amp With S.C. Breaking Capacity of 50kA b. Changeover Switch of rating = 100Amp c. Motor Breakup Protection MCCB of rating = 100-125 Amp With S.C. Breaking Capacity of 36kA d. FASD Submersible starter suitable for 30 HP Load with Relay range of 30-50 Amp e. Auxillary MCCB for Heating/Lighting = 63 Amp With S.C. Breaking Capacity of 25kA f. Capcitor bank of 15KVAr cpacity Rest of Deatils/Technical specification are as per clause 43 (e) of Annexure "C" of SBD for stage 2nd

Fabrication Providing and fitting of modular control panel as technical specification as per cluase 44 of SDB. THE technical details/ Ratings of various components of Modular Control Panel are given Below a. Main Circuit Breaker (Incommer MCCB) of rting = 160-200 Amp With S.C. Breaking Capacity of 50kA b. Changeover Switch of rating = 200Amp c. Motor Breakup Protection MCCB of rating = 84-120 Amp With S.C. Breaking Capacity of 36kA d. FASD Submersible starter suitable for 40 HP Load with Relay range of 36-60 Amp e. Auxillary MCCB for Heating/Lighting = 63 Amp With S.C. Breaking Capacity of 25kA f. Capcitor bank of 15KVAr cpacity Rest of Deatils/Technical specification are as per clause 43 (f) of Annexure "C" of SBD for stage 1st

Fabrication Providing and fitting of modular control panel as . THE technical details/ Ratings of various components of Modular Control Panel are given Below a. Main Circuit Breaker (Incommer MCCB) of rting = 250Amp With S.C. Breaking Capacity of 50kA b. Changeover Switch of rating = 200Amp c. Motor Breakup Protection MCCB of rating = 160-200 Amp With S.C. Breaking Capacity of 36kA d. FASD Submersible starter suitable for 75 HP Load with Relay range of 66-110 Amp e. Auxillary MCCB for Heating/Lighting = 63 Amp With S.C. Breaking Capacity of 25kA f. Capcitor bank of 15KVAr cpacity Rest of Deatils/Technical specification are as per clause 43 (h) of Annexure "C" of SBD for stage 2nd Sadatpora old

Providing and Fitting of 50 sqmm 3.5 core LT 1.1 KV, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer/DG set to control panel including necessary thimbling, crimping, taping etc. NOTE:- The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles of appropriate size and connected by hydraulic crimp tool only.

Steel work in built up tubular (round, square or rectangular hollow tubes, ISMC,ISMB,ISA etc.) trusses, construction of liner etc. including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer , including welding and bolted with special shaped washers etc. complete The drawings and Dimensions for Gantry/Transformer Bed/Pumping Equipment Base will be provided by Site In Charge at the time of execution of job

Providing, installation and testing of manual type triple spur gear chain pulley block along with monorail geared travelling trolley having following features Make = Reputed make Capacity = 3 ton (P) No. Of load chain falls = 2 or above Min. Height of lift = 6 M Rest of Deatils/Technical specification are as per clause 24 of Annexure "C" of SBD for stage 1st

Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. Rest of Deatils/Technical specification are as per clause 50 of Annexure "C" of SBD for stage 1st and 2nd

Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Rest of Deatils/Technical specification are as per clause 51 of Annexure "C" of SBD for stage 1st and 2nd

Providing and installation of Junction Box with DP 32Amp MCB to serve as amin switch for LED lighting. Rest of Deatils/Technical specification are as per clause 52 of Annexure "C" of SBD

Providing, Installation and testing of 2KVA fully automatic voltage stabilizer . Rest of Deatils/Technical specification are as per clause 53 of Annexure "C" of SBD for stage 1st and 2nd

Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter with 12V, 180AH Tubular inverter Battery Rest of Deatils/Technical specification are as per clause 54 of Annexure "C" of SBD

Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen . Rest of Deatils/Technical specification are as per clause 55 of Annexure "C" of SBD for stage 1st and 2nd

TOOL KIT For Maintenance: - The Tool Kit for maintenance as per detailed specification in cluase 56 of Annexure "C" of SBD for stage 1st and 2nd

Providing of good quality conveinence and utility items as per details in Caluse 57 of Annexure "C" of SBD for stage 1st and 2nd

Fabrication of 6’ x 6’ angle iron bed for operators. Rest of Deatils/Technical specification are as per clause 58 of Annexure "C" of SBD for stage 1st and 2nd

Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 2 nos. Rest of Deatils/Technical specification are as per clause 59 of Annexure "C" of SBD for stage 1st and 2nd

Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply for stage 1st and 2nd

Providing of 1 KW heat convector for operators for winter season for stage 1st and 2nd

Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal Rest of Deatils/Technical specification are as per clause 64 of Annexure "C" of SBD for stage 1st and 2nd

Providing & fitting of lighting points for ( machine room , operators room,) as per site requirement in 1.5 mm² multistranded single core 1100 volts, pvc insulated copper conductor through pvc conduit pipe by way, switches, socket modules , regulators ,indicators, 08/10 watt LED lamps Surface light Make. .Included is cost on account of modular switch boards with the wooden frames as per site requirements for stage 1st and 2nd

Providing fitting of heating points in 2.5mm² multistranded single core 1100 volts, pvc insulated copper conductor through pvc conduit by way of p / f of 15 Amp switches, 6 pin socket on modular fitting as per site requirements. Heating points are to be connected from main control panel. All accessories required is to be provided by the firm for stage 1st and 2nd

Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site. Rest of Deatils/Technical specification are as per clause 65 of Annexure "C" of SBD for stage 1st and 2nd

Providing and fitting of 3-Core flat submersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 as per details in Clause 47 of Annexure "C" of SBD for stage 1st and 2nd Size = 16 Sq mm

Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 100mm Rest of Specification/Details are as per clause 16 of Annexure "C" of SBD for stage 1st and 2nd

Handling, laying and joining by welding of departmental GI prefabricated, Medium class GI Rising Mains for Retrofitting from Stage 1st to PST and from clear water sump to 03 No. OHTs As per detailed specification in cluase 114 of Annexure "C" of SBD

For 125 mm Dia GI Pipe

For 100 mm Dia GI Pipe

Providing, fitting and testing of approved quality 125mm dia. sluice valve (01 No), along with 125mm dia. dismantling joint (01 Nos) in the GI Rising Mains at the required location as per the directions of site Engineer. The dismantling joint is to be installed with the sluice valve with the help of flanges including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

Providing, fitting and testing of approved quality 100mm dia. sluice valve (01 No), along with 100mm dia. dismantling joint (01 Nos) in the GI Rising Mains at the required location as per the directions of site Engineer. The dismantling joint is to be installed with the sluice valve with the help of flanges including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

Providing, fitting and testing of approved quality 125mm dia. NRVs (01 Nos), along with 125mm dia. dismantling joints (01 Nos) in the GI Rising Mains at the required locations as per the directions of site Engineer. The dismantling joints are to be fitted with the Non Return valves with the help of flanges including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

Providing, fitting and testing of approved quality 100mm dia. NRVs (01 Nos), along with 100mm dia. dismantling joints (01 Nos) in the GI Rising Mains at the required locations as per the directions of site Engineer. The dismantling joints are to be fitted with the Non Return valves with the help of flanges including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

Providing, fitting and testing of approved quality 50mm dia. CI Double Acting Air Release Valves (01 Nos) in the GI Rising Mains at the required locations as per the directions of site Engineer including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

Providing, fitting and testing of approved quality 125mm dia. Enclosed Type Water Meter (Bulk Type) (01 Nos) in the GI Rising Mains at the required locations as per the directions of site Engineer including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

Providing, fitting and testing of approved quality 100mm dia. Enclosed Type Water Meter (Bulk Type) (01 No.) in the GI Rising Mains at the required locations as per the directions of site Engineer including all welding charges, cost of nuts /bolts, rubber washer, testing of joints.

MAWADAT ELECTNCALS

M/S AL HUDA ELECTRICAL AND MECHANICAL WORKS