PROVISION OF STANDBY OPERATION SUPPORT CENTRE (OPS) ROOM AT SIGNALCOMPLEX AND PROVISION OF OFFICE ACCN, TOILETS AND CERTAIN (B/R) AND (E/M) WORKS AT MT AND MTRS AT HQTC (U) BANGALORE

Amount

M & L surface excavation n.exc 30cm deep and averaging 15cm deep and getting out hard/dense soil.

Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes,complete all as specified and directed.

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. and getting out in hard/dense soil complete all as specified and as directed.

All as per item above but for additional 1.5m or part thereof in depth beyond the first 1.5 m etc. complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and as directed.

Material and labour for Sand filling under floors or in foundations for cable cushioning including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

Removal of surplus soil (excavated soil) to distance not exceeding 50m and depositing where directed at a level not exc 1.5m above the starting point and all specified.

Removing excavated material exc. 1.50 km but n exc.5km and depositing where directed

Material and labour for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

Material and labour treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured ) complete all as specified and as directed.

Material and labour treating the top surface of filled earth at thte rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

Material and labour treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface areacomplete all as specified and as directed.

Material and labour treating along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.

M&L cement concrete type D-2, 1:4:8, using 40mm graded aggregate as in foundations, fillings and mass concrete complete all as specified and as directed.

Material and labour for providing, plain cement concrete Type C1 1:3:6 (20mm graded aggregate) in lintels upto 1.5m clear span, window cills, steps, plinth courses, copings, bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

M&L for Pre-cast cement concrete block type C1 1:3:6 (20mm graded stone aggregate) masonry with solid blocks, exc. 10cm in width and setting in mortar 1:6 complete all as specified and as directed.

M&L Providing precast cement concrete solid building blocks or slabs 10cm thick of Type C1 1:3:6 (20mm graded aggregate) (with plain or interlocking joints as directed) setting in mortar 1:6, in walls complete all as specified and as directed.

Material and labour reinforced cement concrete (design mix M-25) using 20 mm graded crushed stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc. complete all as specified and as directed.

Material and labour reinforced cement concrete (design mix M-25) using 20 mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour reinforced cement concrete (design mix M-25) using 20 mm graded crushed stone aggregate as in chajjas complete all as specified and as directed.

Material and labour reinforced cement concrete (design mix M-25) using 20 mm graded crushed stone aggregate as in roof beam, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and as directed.

Material and labour reinforced cement concrete (design mix M-25) using 20 mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts etc. complete all as specified and as directed.

Supply only liquid water proofing compound

Material and labour for 25 mm thick Damp proof course in cement concrete 1:2:4 , type B-0 using 12.5 mm graded crushed stone aggregate to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in ement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping).with rough finished surfaces complete all as specified and as directed.

Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges with rough finished surfaces of concrete ,flat complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.with rough finished surfaces complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surfaces complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide.with rough finished surfaces complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed.

S&F factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site etc. complete all as specified and as directed.

S&F solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and as directed.

S&F for 200mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S & F in repairs stainless steel self closing auto hinges for wooden cabinet shutter complete all as directed

S&F 250mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed.

S&F 125mm long Butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F 100mm long Butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F 150 mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

S&F 125mm Aluminium handles, cast type anodised complete all as specified and as directed.

S&F 75mm size Aluminum mortice lock, vertical type, 4 levers, incl plates and two keys, all as specified and as directed complete all as specified and as directed.

S&F Brass cromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F ball catcher with 8 mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified

S&F 20mm mesh Wire netting of galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples etc. complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc. complete all as specified and as directed.

M&L Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F for Mild steel work in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; plate washers and similar small articles conforming to FE-290 Gde-E-165 all as specified.

S&F 1.6mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

Material and labour mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per item No 53 here in above but TMT bars 8 mm dia in stirrups, spacers and binders etc. complete all as specified and as directed.

S&F Fe 410 - W (Gde-E- 250) quality-A plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

M&L for providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over anodised aluminium snap grid frame work for false ceiling with hangers 3mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long incl two coats of distempering with distemper oil emulsion over a coat of 3mm thick wall care putty etc. complete all as specified.

M&L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming Fe 410-W (Gde E-250) quality A, complete

S&F Fe 410 - W (Gde-E- 250) quality-A Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded, complete

S&F for powder coated anodised aluminium frame work (minimum thickness of powder coating 50 micron) for doors, windows, ventilators etc. with one or more rebates including joining cleats for fixing etc. complete all as specified and as directed.

S&F for Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified etc. complete all as specified and as directed.

S&F for Powder coated Anodised Aluminium windows and ventilator shutters, side hung/sliding type without sash bars, (Thickness or powder coating not less than 50 micron), aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.), etc. complete all as specified and as directed.

S & F Powder coated Aluminium Frame work for grills Deco-grill Model DG-104 (10mm) making shape and riveted with rivets and fixed with suitable channel with necessary fixing arrangements etc.complete all as specified and as directed.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall or in door, fixed with self tapping screws as specified.

S&F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI grid/section size 600mmx600mm with main runner 38x24x0.9mm thick, cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 3mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper complete all as specified.

S&F for Prelaminated particle board, 12 mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber/ aluminium frame work complete all as specified and as directed.

S&F in repairs for Prelaminated particle board, 18/19mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B-2 (40mm graded aggregate) as in sub-base layer complete all as specified and as directed.

Material and labour for 75 mm thick cement concrete 1:3:6 type C-1 using 40mm graded crushed stone aggregate as in plinth protection, etc complete all as specified and as directed.

Material and labour for 100 mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate as in flooring finished rough etc. complete all as specified and as directed.

M&L for 75mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in path, hardstanding, etc and finishing cement concrete surface even and smooth without using extra cement etc. complete all as specified.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) on Padding/ roof surfaces all as specified.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in flooring incl finishing cement concrete surface even and smooth without using extra cement etc. complete all as specified.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in flooring complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed.

M&L for glazed ceramic coloured wall tiles in vertical surface 350x250x7mm/ 450x300x7mm/ 450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 complete all as specified and as directed.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 all as specified.

M&L for non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 all as specified.

All as per item No 84 here-in-above but as in skirting over and including 10mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified.

M&L for Vitrified Ceramic tiles in light shade 10mm thick of size 600mm x 600mm in floors etc. set and jointed in neat cement slurry over and including 15 mm thick screed bed of CM 1:6 and pointed in white/ coloured cement to match all as specified.

All as per item No 86 here in above but as in skirting over and including 10mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified.

M&L for chequered cement concret tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with white cement & pigments in floors over 20mm thick screed bed of cement mortar 1:6 all as specified & directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and including 15mm thick screed bed of CM 1:6 all as specified.

M&L for 20mm thick Granite (Jet black) of any type work (table rubbed and polished) in cooking platform, window sill and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade granite incl 20 mm thick screed bed in CM 1:4.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and labour for Polythene film, black, 50micron laid in floors etc. complete all as specified and as directed.

M&L for Rendering 10mm thick on fair faces of brick works or concrete surfaces in CM 1:6 and finished even and smooth without using extra cement all as specified.

M&L for rendering 10mm thick cement plaster in cement morter 1:3, mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces or roof surfaces, finished even and smooth without using extra cement complete all as specified and as directed. Note: Liquid WPC will be measured and paid separately

Material and labour rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces mixed with water proofing compound as per manufacturers instructions , finished even and smooth with out using extra cement complete all as specified and as directed. Note :- WPC will be measured and paid separately under relevant item.

Rendering 5mm thick cement plaster in cement mortar 1:3, on concrete sufaces as in ceiling, finished even and smooth without using extra cement complete all as specified and as directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. Including racking out joints, hacking for key, scrubbing down with water, etc. all as specified.

M&L for preparation of old decorated plastered or unplastered surface of walls including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying one coat of white washing complete.

All as per item No 98 here-in -before but one coat of white washing on ceiling.

M&L for 2 coats of Distempering wall with distemper oil emulsion white or tinted over a coat of chalk whiting, including preparation of old surface after complete removal of existing treatment all as specified.

M&L for preparing newly plastered on walls and applying three coats of white wash complete all as specified and as directed.

M&L for preparing new plastered on ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for 2 coats of Distempering wall with distemper oil emulsion white or tinted over a coat of chalk whiting, including preparation of new surface all as specified.

M&L for 2 coats of Distempering wall with distemper oil emulsion white or tinted over a coat of 3mm thick wall care putty, including preparation of new surface all as specified.

M&L for 2 coats of cement paint over a coat of priming plastered and other surfaces with alkali resistant priming paint including preparation of new surfaces all as specified.

S & F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and as directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sq. M in each pane, etc. complete all as specified and as directed.

M&L for water proofing treatment on horizontal or vertical surfaces by applying oil bound bitumen primer & 0.20 Kg/Sqm and providing 4 mm thick APP modified water proofing membrane weighing not less than 4 Kg/Sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm including minimum 10 cm side lap and 15 cm end lap torch sealed and bonded and applying a coat of blown grade hot bitumen 90/15 over and below the membrane @ 1.20 Kg/Sqm in drying over the membrane finished with solar reflective bituminous aluminium paint/primer @ 0.1 Kg/Sqm over RCC roof slab/ projection/ parapet after cleaning the surfaces by removing dust dirt etc as manufactures instructions complete all as specified and directed.

Preparation of old painted surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old painted surface of any description not otherwise described steel and iron surface over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10 cm width or girth including necessary preparation of surfaces all as specified and as directed.

S&F square grating doom 150 mm side with or without waste hole of stainless steel consisting of 0.45 mm thick inner and outer cup and 1.0mm thick top grating with ring to be fixed inside 'P' traps with cement concrete complete all as specified and as directed.

S&F 15mm Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F 15mm two in one Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F 15mm pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure,with or without lettered "Hot" or "Cold" with long screwed shank and fly-nuts, screwed for iron pipe and fixed all as specified.

S&F stop valve 15mm bore, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified.

Supply & fixing in repair 25 mm dia Gun-metal, globe or gate valves, heavy duty, with iron wheel head, screwed both ends (ISI marked) complete all as specified & directed.

S&F angle cock 15mm bore, fancy type chromium plated fixed all as specified.

S&F PVC connections 15mm size with PTMT nuts of length 600mm all as specified.

S&F Soap dish, any type of size approximate size 160x 60x90mm, fixed to plugs with chromium plated brass screws

S&F Brass chromium plated shower rose 125mm size all as specified.

S&F 5mm thick mirror of size 450mm x 600mm mounted on 6mm thick commercial ply wood backing and screwed with PVC channel alround complete all as specified and as directed.

S&F Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook complete all as specified and as directed. Make Cera, Parryware, Somany, Jaguar or equivalent.

S&F glass corner shelf assembly fancy type made of 5 to 6mm thick glass of size 250 x 250mm fixed with brass CP brackets complete all as specified and directed.

S&F premium quality wall mixer system with provision for overhead shower complete with 115mm long bend pipe, connecting Legs & wall Flange complete all as specified and as directed. Make Jaguar, Cera, Somany or equivalent.

S&F wash basins, Vitreous China white,(flat back type) size 550x400mm, pedestal type, excluding taps, chain and plug and porcelain stopper but including brackets, waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins white or tinted, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed, including cutting for and pinning in ends of brackets or erecting stand etc. complete all as specified and as directed.

S&F vitreous china wash down water closet pan (pedestal pattern), including 10 ltr capacity low level white PVC flushing cistern with inlet, ball valve, float and handle; flush pipe, plastic water closet seat, white or tinted, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F Vitreous China urinals,half stall urinal type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), etc. complete all as specified and as directed.

S&F curved shaped frameless urinal partition with 8mm thick frosted glass of size 450mm x 900mm with CP brackets 04 Nos etc. complete all as specified and as directed.

S&F UPVC 15mm internal dia pipe of pressure rating 10kgf/cm² fixed complete to walls, ceiling or in floor etc., any type of pipe complete all as specified and as directed.

All as item No 131 above but 20mm bore

All as item No131 above but 25mm bore

S&F rotational moulded polyethylene water storage tanks, capacity in litres 500 (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.

S&F ball valves 20mm dia, high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete all as specified and as directed.

S&F and in repair PTMT ball valve, high pressure, with epoxy coated aluminium rod and high density plastic ball screwed for 25mm bore GI tubes, fixed in repairs, all as specified and as directed.

Supply and Laying GI Pipe light grade 80 mm dia for protection of UG cable complete all as specified and as directed.

Supply and fix 25mm dia galvanised water tubes, medium grade including all fittings, laid in trenches complete all as specified and as directed.

Supply and fix 25mm dia galvanised water tubes, medium grade including all fittings, laid in wall/ ceiling/floors complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends of any radius all as specified.

S&F PVC (SWR) bends 110mm bore vent cowl

S&F PVC (SWR) 'P' or 'S' trap 110mm bore.

S&F PVC (SWR) pipes 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) Junction single (Single T) equal or unequal all as specified.

S&F 75mm bore PVC (SWR) bends of any radius all as specified.

M&L for cutting into existing manholes for connecting new drains, making good to 100mm pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound of grade 'A' complete all as specified and as directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dresses stonework and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed.

Removing demolished building materials and debris to a distance of 30km or beyond, out of premises of metropolitan area, incl loading, unloading by manually or by mechanical means (JCB) and to be transported through tractor-trolly or tipper and stacking at the destination during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

M&L for Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core complete all as specified and as directed.

Supplying and laying un-reinforced precast concrets cable cover class LV Type 1 flat size 250x150x40mm complete all as specified and as directed.

Supply, laying, jointing, testing & commissioning in pipes/ducts/trenches / under floor/under road cables XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured electric power cable (Heavy duty) with aluminium conductor 1100 Volt grade of following cross sectional area 16 Sqmm 4 core.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Taking down carefully copper/aluminium point wiring (light fan socket or power) complete including fittings such as switches, ceiling rose, pendants, regulators, sockets, light fittings complete as directed and removing retrieved materials and making good the disturbed surface all as specified and as directed.

Material and labour for Point wiring consealed type complete with 1100volts grade, single core, PVC insulated FRLS cable multi-stranded copper conductor of size 1.5 sqmm nominal area, drawn through and including rigid, PVC conduit of suitable size, with all necessary fittings and accessories fixed on walls/ ceiling with one run neutral and one run of single core cable of same description above but green colour in continous earthing wire connected to common earth dolly including PVC junction / mounting boxes on / in the wall for switch socket combination and GI junction box duly covered with 3mm thick hylam sheet complete for the independent switch to ceiling rose

(a) One light/ fan point controlled by one single pole 5 Amps switch

(b) One switch socket out let point 5 Amps on same board with other switches

(c) One switch socket out let point 5 Amps on independent board

M&L for Chassis cutting in wall/ ceiling for point wiring as above etc complete all as specified and as directed.

Point wiring with cable of PVC insulated FRLS copper multistranded conductor 2.5 sqmm 1100 volts grade in and including heavy grade with recessed/ concealed PVC Conduit ISI marked, broken white/or of cream /grey colour. with all accessories and fixing arrangements on wall/ceiling surface on wall including new 3mm thick hylum sheet top cover/PVC gang box fixing on wall surface for housing switches/sockets/regulators etc. with and including 2.5 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for one 15A Switch Socket Combination on independent board all as specified and as directed.

All as per item No 160 here in before but for PVC insulated FRLS copper conductor of size 4.0 sqmm for switch socket multipurpose 15 Amps including provision of 4.0 Sq mm PVC insulated FRLS copper conductor cable as earth continuity conductor on independent board

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fix LED surfacerecess mounted luminaire suitable for 2x2 ft grid ceiling with system wattage of 36 watts , 3600 lumnes, CCT 6500k , CRI > 80 , IP 20 , complete incl PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting (Make-Philips of Catalogue No. RC420B M LED30S 6500 PSU WH , or equivalent in Wipro/Havells

Supply and fixing LED lights fitting 4 feet, 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fix Modularswitch , 1 Module single pole one way 10 Amps complete all as specified and as directed.

Supply and fixing modular swich one way 16 Amps one module, 230 volts all as specified

Supply and fix modular socket , 2 Module 6 Amps 240 volts Ac 2/3 pin combined suitable for inserting 2 pin 5 Amps/ 3 pin 5 Amps plug top all as specified and directed.

Supply and fix modular socket , 2 Module 6/16 Amps 240 volts Ac 6 pin combined suitable for inserting 3 pin 6/16 Amps plug top all as specified and directed.

Supply and fix Modulars fan regulator, 2 Module120 Watt

Supply and fixing modular white cover suitable with frame 2 module.

Supply and fixing modular white cover suitable with frame 3 module.

Supply and fixing modular white cover suitable with frame 4 module.

Supply and fixing modular white cover suitable with frame 6 module.

Supply and fixing modular metal flush board 1/2 module

Supply and fixing modular metal flush board 3 module

Supply and fixing modular metal flush board 4 module

Supply and fixing modular metal flush board 6 module

S&F MCB SP 6-40 Amps, 240 volts with breaking capacity of 10 KA complete all as specified and as directed.

S&F MCB TPN 63 Amps, 415 volts with breaking capacity of 10 KA complete all as specified and as directed.

Supply and fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with single pole MCB 20 Amps 240 Volts AC complete all as specified and as directed.

Supply and fixing Sheet metal enclosure, single pole and neutral 8 Way double door type MCB DB's with 200 copper busbar complete all as specified and as directed.

S&F stell sheet enclosure double door type for MCB DB TPN 4 way, 415 volts AC factory made, suitable for housing MCB TPN and SP along with 200 Amps copper bus bar complete all as specified and as directed.

Supply and fixing Sheet metal enclosure, single pole and neutral 4 Way double door type MCB DB's with 200 copper busbar complete all as specified and as directed.

Supply and fix PVC ceiling rose 65 x 50 mm surface type with 3 terminals all as specified and directed.

Material and labour for Earthing complete with copper earth plate electrode 60x60cmx3.15mm thick, buried directly in ground ( earth pit not less than 2.25mtrs deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level, connected to copper strip 20x3mm as earth lead by means of bolts, nuts, check nuts and washers of brass or steel all as shown in electrical plate No.3 connected to earthing test point.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre below ground level) with top edge of the earth plate not less than 1.5 metre below ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part I connected to earth test point all as specified or indicated including excavation and connected earth work, in soft/loose soil, removing soil upto 50m, PCC 1:3:6 type C1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 40mm bore GI medium grade earth lead protection pipe, 50mm thick RCC 1:2:4 type B1 cover slab of earth pit reinforced with 8 mm dia TMT Bars @ 10cm C/C both ways and with handle made out of 20mm dia bars, funnel, strainer, alternate layer of charcoal dust and common salt and testing on completion , complete all as specified and directed.

Supply & fix Ceiling fans complete with electronic type with regulators and accessories 230V, 1200mm sweep, BEE 5 star rated complete all as specified and as directed.

Supply & fix heavy duty exhaust fans of size 450mm sweep, AC single phase 230/ 240 V of metallic body with louver and other accessories complete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply and fix Pedestal fan, steel body AC single Phase. 230V of size 500m sweep with, blades, and stand complete all as specified and as directed.

S&F Wall mounted fan 400mm with oscillation complete with all fixing accessaries complete all as specified and as directed.

Supply and fixing of ON LOAD Change Over switch front handle operated 415V 50hz four pole all open execution type of capacity 63 Amps complete all as specified and as directed.

15W recess mounted high performance low-height LED downlighter suited for requirements non-integral flexible , die-cast Al. LED fixture with ivory powder coating for updown accent lighting. Range 220 V - 240 V, 50Hz complete with incl connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire, complete all as specified and directed. Make Phillips cat part No DN296B LED 15S-6500 PSUWH.

Taking down ceiling fan and re fixing after painting of ceiling fans complete, with synthetic enamel paint by praying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed.

Supply and laying consealed type sub main wiring with Two single core PVC insulated cable with copper conductor multistranded 1100 volts grade 6.0 sqmm drawn through and including rigid, PVC casing & caping of suitable size, with all necessary fittings and accessories fixed on walls, floor or ceiling etc including 6.0sqmm PVC insulated unsheathed copper earth continuity conductor. Note : One run of earth continuity conductor,one run of PVC conduit and two run of copper conductor together taken as one length for measuring unit length.

Supply and laying of sub main wiring with 6 single core PVC insulated cable with copper conductor multistranded 1100 volt grade 4.0 sqmm in PVC conduit/ casing caping and including 2x4 sqmm PVC insulated multistranded copper conductor and connecting to main earth dolly complete all as specified and directed

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB SP) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB SPN) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning of capacity 40 to 63A complete all as specified and as directed.

Supply, install and testing of wall split units indoor/outdoor complete with cordless remote control unit and with in built air filter for better indoor air quality iwthminimum 5 star rating inverter model capacity 1.5 TR BE rating is not less than 3.2, complete all as directed and specified.

Supply, install and testing of wall split units indoor/outdoor complete with cordless remote control unit and with in built air filter for better indoor air quality iwthminimum 5 star rating inverter model capacity 1.0 TR BE rating is not less than 3.2, complete all as directed and specified.

H S S ENGINEERS AND CONTRACTORS