Supply of Tools Equipments and Machineries of Electrician Trade

Measuring Steel Tape 5 meter

Combination Plier Insulated 200 mm

Screw Driver Insulated 4mm X 150 mm, Diamond Head

Screw Driver Insulated 6mm X 150 mm

Electrician screw driver thin stem insulated handle 4mm X 100 mm

Heavy Duty Screw Driver insulated 5mm X 200 mm

Electrician Screw Driver thin stem insulated handle 4mm X 250 mm

Punch Center 9mm X 150 mm

Knife Double Bladed Electrician 100 mm

Neon Tester 500 V

Hammer, cross peen with handle 250 grams

Hammer, ball peen With handle 500 grams

Pincer 150 mm

C- Clamp 200 mm and 100 mm 2 Nos. each

Spanner Adjustable drop forged, SS 150 mm & 300mm 2 Nos. each

Chisel Cold 25 mm X 200 mm

Chisel firmer with wooden Handle 6 mm X 200 mm

Grease Gun

Bradawl 0.5 ltr. Capacity

Pulley Puller with 3 legs 300mm

Bearing Puller (Inside) 200 mm

Pipe vice Cast Iron with hardened jaw open type - 100 mm

Scissors blade, SS - 200mm

Scissors blade, SS - 150mm

Crimping Tool 1.5 sq mm to 16 sq mm - 2 Nos

Crimping Tool 16 sq mm to 95 sq mm - 2 Nos

Wire Cutter and Stripper 150 mm

Mallet hard wood

Hammer Extractor type

Inside Calliper

Divider

Pliers long nose insulated

Pliers flat nose insulated

Pliers round nose insulated

Tweezers

Snip Straight and Bent heavy duty - 2 Nos each

D.E. metric Spanner Double Ended

Drill hand brace

Drill S.S. Twist block

Plane cutters

Smoothing cutters

Gauge, wire imperial stainlees steel marked in SWG & mm

File half round

File round

File flat rough

Copper bit soldering iron.

De soldering Gun

Hand Vice

Oil Can

Contactor & auxiliary contacts 2 Nos. each

Contactor & auxiliary contacts. 2 Nos. each

Limit Switch

Rotary Switch

Relay- a. Cut out Relays - 16A, 440V - 2 Nos b. Reverse current - 16A, 440V - 2 Nos c. Over current - 16A, 440V - 2 Nos d. Under voltage - 360V-440V - 2 Nos

Pin Type, shackle type, egg type & suspension type insulators including hardware fitting - 2 Nos each

Hand Drill Machine

Load Bank ( Lamp / heater Type)

Brake Test arrangement with two spring balance

Laboratory Type Induction Coil

Thermometer Digital

Series Test Lamp

Knife Switch DPDT fitted with fuse terminals

Knife Switch TPDT fitted with fuse terminals

Earth Plate 60cm X 60cm X 3.15mm Copper Plate - 1 No and 60cm X 60cm X 6mm GI Plate

Earth Electrode

MCCB 100Amps, Triple pole

ELCB and RCCB 25Amps, double pole and 25Amps, double pole, IΔn 30 mA - 1 Each

Fuses HRC Glass Rewire Type

Rheostat (Sliding type) 0 - 25 Ohm, 2 Amp - 1 No 0 - 300 Ohm, 2 Amp - 1 No 0 -1 Ohm, 10Amp - 1 No 0 -10 Ohm, 5 Amp - 1 No

Capacitors Electrolytic Ceramic Polyester film Variable Dual run

Various Electronic components Resistors, Diode, Transistor, UJT, FET, SCR, DIAC, TRAIC, IGBT, Small transformer etc. - As required

Various Lamps - Halogen Incandescent Lamp Fluorescent tube, HP mercury vapor Lamp High-pressure sodium Lamp Low-pressure sodium Lamp LED - 1 Each

Plug socket Piano Switch Lamp Holder - 230 V, 5 A

Cables : Twisted Pair Non-Metallic Sheathed Cable Underground Feeder Cable Ribbon Cable Metallic Sheathed Cable Multi-Conductor Cable Coaxial Cable Direct-Buried Cable NOTE: 1 Meter for all Cables mentioned above

Bus bar with brackets 1 Meter each

Rubber mat 2’ x 4’ x 1”

RCC Pole with accessories (MS angle iron, ‘C’ clamp, stay insulator etc.) and materials - 6 Mtr

Ohm Meter; Series Type & Shunt Type, portable box type 50/2000-ohm analog - 2 Nos Each

Digital Multi Meter

A.C. Voltmeter M.I. analog, portable box type housed in Bakelite case

Milli Voltmeter centre zero analog, portable box type housed in Bakelite case

Ammeter MC analog, portable box type housed in Bakelite case 0 - 500 mA, 0-5 A, 0-25 A : 02 Nos Each

AC Ammeter MI, analog, portable box type housed in Bakelite case 0 - 1 A, 0-5 A, 0-25 A : 02 Nos Each

Kilo Wattmeter Analog

Digital Wattmeter

A.C. Energy Meter Single Phase, 10 A, 240 V induction type

A.C. Energy Meter Three Phase, 15 A , 440 V induction type

Power Factor Meter Digital

Frequency Meter

Magnetic Flux Meter

Lux meter

Tachometer Analog Type - 10000 RPM

Tachometer Digital Photo Sensor Type – 10000 RPM

Tong Tester / Clamp Meter

Megger

3- point D.C. Starter

4- point D.C. Starter

Wheat Stone Bridge with galvanometer and battery

Single Phase Variable Auto Transformer

Phase Sequence Indicator

Growler

AC Starters: - For A.C Motors of 2 to 5 H.P. - 1 No Each a. Resistance type starter b. Direct on line Starter c. Star Delta Starter- Manual d. Star Delta Starter – Semi automatic e. Star Delta Starter – Fully automatic f. Star Delta Starter - Soft starter g. Auto Transformer type NOTE: 01 No Each

Oscilloscope Dual Trace

Function Generator

Soldering Iron - 01 No Each 25 Watt, 65 Watt and 120 Watt, 230 Volt

Temperature controlled Soldering Iron - 50 Watt, 230 Volt

Discrete Component Trainer

Linear I.C. Trainer

Digital I.C. Trainer

Oil Testing Kit

Voltage Stabilizer

DC Power Supply

Battery Charger

Current Transformer

Potential Transformer

D.C. Shunt Generator with control panel - Please Refer Technical Specifications for detail specifications

Motor-Generator (AC to DC) - Please Refer Technical Specifications for detail specifications

D.C. Compound Generator with control panel including fitted rheostat, voltmeter, ammeter and breaker Please Refer Technical Specifications for detail specifications

DC Series Motor coupled with spring balance load - Please Refer Technical Specifications for detail specifications

DC Shunt Motor Please Refer Technical Specifications for detail specifications

DC compound Motor with starter and switch Please Refer Technical Specifications for detail specifications

Motor Generator(DC to AC) set consisting of - Shunt Motor with starting compensator and switch directly coupled to AC generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. Set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. Please Refer Technical Specifications dor detail specifications

AC Squirrel Cage Motor with star delta starter and triple pole iron clad switch fuse with Mechanical Load.

AC phase-wound slip ring Motor with starter switch

Universal Motor with starter/switch

Synchronous motor with accessories like starter, excitation arrangements.

Thyristor /IGBT controlled D.C. motor drive with tacho-generator feedback arrangement - 1 HP

Thyristor /IGBT controlled D.C. motor drive with tacho-generator feedback arrangement - VVVF control 3 Phase, 2 HP

Single phase Transformer, core type, air cooled

Three phase transformer, shell type oil cooled with Delta/ Star

Electrical Machine Trainer - Suitable for demonstrating the construction and functioning of different types of DC machines and AC machines (single phase and three phase). Should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supply unit

Used DC Generators-series, shunt and compound type for overhauling practice - 1 Nos Each

A.C. Series type Motor

Single Phase Capacitor Motor with starter switch

Manual Motor coil Winding Machine

Ceiling fan coil Winding Machine

Primary current injection set

Stepper Motor with Digital Controller

Shaded Pole Motor

Working Bench 2.5 m x 1.20 m x 0.75 m

Wiring Board 3 meter x1 meter with 0.5 meter projection on the top

Metal Rack 100cm x 150cm x 45cm

Lockers with drawers - 1 for each trainee

Almirah 2.5 m x 1.20 m x 0.5 m

Xtreme Engineering Equipment Pvt Ltd

Prowiz Systems