SPL REPAIR TO JCOs MD ACCN (FAFA) (BLDG NO P-78/1-4) (NO OF Dus -04) AKBAR ROAD AND PROVN OF SECURITY FENCING AND STEEL GATE WITH GRANITE PILLAR AT UNIT KOTE OF 50 (I) PARA BDE SIG COY UNDER AGE B/R-I (W) GE(W) AGRA

Amount

M&L surface dressing n exc 15 cm deep soft/loose soil complete all as specified and directed by Engr-in-Charge.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as per specified and directed by Engineer -in-charge..

M&LCement concrete Type B2 1:2:4 in foundations, filling and mass-concrete complete all as per specified and directed by Engineer -in-charge.

S&FJoist, channel, angle , or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)FE 290 Gde 165 complete all as per specified and directed by Engineer -in-charge.

Supply of chain link MS galvanised fencing 3.40mm dia size of mesh 100X100mm including straining bolt,bar and binding wire. complete all as per specified and directed by Engineer -in-charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as per specified and directed by Engineer -in-charge.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long dia of neck 11 to 15mm. complete all as per specified and directed by Engineer -in-charge.

Supply and fix Mild steel round 10MM dia bars, in available lengths to strengthening chan link fencing. complete all as per specified and directed by Engineer -in-charge.

Supply and fix Mild steel in flat Fe-410-W(Gde-E-250)quality-A, in available lengths to strengthening chan link fencing. complete all as per specified and directed by Engineer -in-charge.

Preparation of new painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying a coat of red oxide and over two coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

S & F Galvanised 2 strand, steel barbed wire 2.00mm dia at 75mm spacings and training and fixing to any type of standard rails training bolts, including, securing or tying at crossings with and provision of galvanised mills steel wire, staples or steel pins, etc. as direcdted ( each line wire to measured).

M&L Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil as in foundation complete all as specified and directed by Engr-in-Charge

Returning filling in trenches in layers n. exc 25cm thick, watering, well ramming complete in soft/loose soil complete all as specified and directed by Engr-in-Charge

Removing excavated material n. exc 50m and depositing where directed at level n. exc 1.50 in soils complete all as specified and directed by Engr-in-Charge

M&L for 15mm thick rendering in other than fair faces in CM 1:4 incl water proofing compound complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new surfaces of wall and applying 1mm thick water proof wall care putty and over two coats of cement base paint paint etc complete all as specified and directed by Engr-in-Charge

M&L Cement concrete Type B1 1:2:4 in coping complete all as per specified and directed by Engineer -in-charge.

M&L for form work to sides of concrete foundations ,footings and lintel beam similar work or to better rough finished surface of concrete etc complete all as specified and directed by Engr-in-Charge

M&L for form work to sides of pillars,posts,strut,piers,columns and stanchions finished surface of concrete etc complete all as specified and directed by Engr-in-Charge.

M&L for RCC grade A-1, type (1:1.5:3) Nominal mix using 20 mm graded coarse aggregate as in footing foundation complete all as specified and directed by Engr-in-Charge

M&L for RCC grade A-1,type (1:1.5:3) Nominal mix using 20 mm graded coarse aggregate as in columns complete all as specified and directed by Engr-in-Charge.

S&F mild steel TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns hooking ends and binding with mild steel wire anealed not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge

.-ditto- 5mm dia and over upto and including 10mm dia in stirrups etc complete all as specified and directed by Engr-in-Charge

M&L 18/20mm thick black granite (of any type) work (table rubbed and polished) in steps jambs, pillars, window cills, cooking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of stone including rounding and moulding of edge and making hole for cooking gas pipe complete all as specified and directed by Engr-in-Charge.

M & L frameed work Fe - 410-W-(Gde-E250) as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guids) and hanging also fastening and fixing complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engr-in-Charge.

Dismantling brick tiles in roof top laid bedded & pointed in any mortar and removing from site acomplete all as specified and directed by Engr-in-Charge

Demolition of mud or existing roof treatment of, any thickness, including plastering and leaping and tiling of any description whether part removal or full or complete all as specified and directed by Engr-in-Charge.

Disposal of removed/demolished soil/materials exc 1.50 km but n. exc 5 km and depositing where directed complete all as specified and directed by Engr-in-Charge

M&L cement concrete type B-0, 1:2:4 mix ( 12.5 mm graded agg) complete all as specified and directed by Engr-in-Charge.

M & L three coat of Roof waterproofing solutions smartcare damp proof ultra an innovative fiber reinforced elastomeric liquid which provide the ultimate waterproofing cover of 2.32sqm/Liter with 10 years of waterproofing warranty and upto 12 degrees celsius of surface temperature reduction complete all as specified and directed by Engr-In-Charge.

Supply only integral water proofing compound liquid admixture for mortar (Make - Fosroc , Conplast WL) complete all as specified and directed by Engr-in-Charge.

M&L for Cement concrete 1:2:4 type B-1 ( using 20mm graded crushed stone aggregate) complete all as specified and directed by Engr-in-Charge

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles ccomplete all as specified and directed by Engr-in-Charge.

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified and directed by Engr-in-Charge

M&L for brick work with sub class ‘B’ bricks old size, straight or curved on plan exc 6 M mean radius, built in CM 1:6 complete all as specified and directed by Engr-in-Charge. Note:- Bricks obtained from item No 12 shall be reused after cleaning.

Taking down cement or cement lime plaster of any discription on brick or stone walls/ ceilings etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge

M&L for 15mm thick rendering in CM 1:6 on any faces of brick or concrete surfaces of walls & finishing the surface even and fair without using extra cement complete all as specified and directed by Engr-in-Charge

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 marble chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the marble chippings, all design and pattern approved by Engr-In-Charge complete all as specified (Payment for providing grooves shall be made separately)

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove using cement complete as per specifications and direction of the Engineer-in-charge

M & L for rendering 10mm thick in CM 1:4 on ceiling surface finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge

M&L Preparing newly plastered or un plastered surfaces of wall and applying two coats of oil bound distemper with roller application over a coat of primer over a coat of average 1mm thick wall care putty on new plastered surfaces complete all as specified and directed by Engr-in-Charge

M&L for applying two coats of oil bound distemper with roller on old decorated wall surfaces over 1 mm thick white putty including complete removal of existing treatment with mechanical complete all as specified and directed by Engr-in-Charge.

M&L for applying three coats of white wash on wall including preparation of new plastered or un-plastered surfaces of walls, complete all as specified and directed by Engr-in-Charge

M&L for complete removal of extg treatment with mechanical device of old plastered surfaces of wall and applying two coat of white wash (match with new surface) complete all as specified and directed by Engr-in-Charge

M&L for applying three coats of white wash on ceiling including preparation of new plastered or un-plastered surfaces, complete all as specified and directed by Engr-in-Charge

M&L for applying two coats of white wash on ceiling including complete removal of existing treatment with mechanical complete, complete all as specified and directed by Engr-in-Charge

S&F mild steel joist channel angle or tee sections fixed independently with out connecting plates etcof grade Fe-410-W (Gde E-250 quality B) complete all as specified and directed by Engr-in-Charge

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L One coat of epoxy resin (FAIR BOND EP) on old concrete surface @ 0.30 kg/Sqm including preparation of surface as per as per manufacturer's instruction and applying 25 mm thick on ceiling, beams, chajjas & facia surface etc (average thickness) of cement and sand (fine grit) in ratio 1:4 mixed with chloride free sprey concrete plasticiser (spray crete) as per manufacturer's instruction with guniting machine of pressure capacity not less than 5kg per Sqm and finished the surface even & smooth in CM 1:4 plaster min. 10 mm thick ccomplete all as specified and directed by Engr-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-Charge

M&L for coloured glazed ceramic tiles in vertical surface 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and directed by Engr-in-Charge

M&L non skid joint free coloured tiles (1st quality/ premium quality) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exc. 0.11 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) ccomplete all as specified and directed by Engr-in-Charge.(toilet,bath,kitchen, passage floor)

M&L non skid joint free coloured tiles (1st quality/premium quality) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18Sqm but not exc. 0.38 Sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and directed by Engr-in-Charge. (bed room and other room floor)

M&L Varoda green marble makrana Adanga stone 18 to 20 mm thick in steps, pillars, wndow cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge.

M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 20mm thick screed bed CM (1:6) complete all as specified and directed by Engr-in-Charge.

M&L Machine cut kota stone 18-20 mm thick as in riser of step, skirting,dado and pillar etc. laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing laid over and including 15mm thick rendering CM (1:4) complete all as specified and directed by Engr-in-Charge

Boring holes through cooking platform lining for pipes ,etc n'exc 50mm dia and making good complete all as spd and dir by Engr-in-charge.

M&L 25 mm thick PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in sub base of flooring finished even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

PCC 1:3:6 C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection ( 75 mm thick ) laying in alternate ways finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

S & F in repairs 15 mm bore chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge

S&F in repairs 10 ltrs capacity PVC flushing cistern low level (white) with inlet ball valve and handle including flush pipe, brackets, rubber bush, washers etc complete all as specified and directed.

S&F in repair 15 mm bore CP Stop valve / angle valve screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm bore CP concealed Stop valves, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with 'P' or 'S' trap front or back inlet including footrest (excluding fluxing cistern and flush pipe) complete all as specified and directed by Engr-in-Charge.

S&F in repair 500 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20 mm dia (minimum weight - 210 gm) complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm size with PTMT nuts, 600 mm long complete all as specified and directed by Engr-in-Charge

S&F in repairs Vitreous china wash basin white flat back size 550 x 400mm incl waste pipe chain plug brackets complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bore, brass chromium plated pillar cock (foam flow) two ways screwed down for pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Waste coupling of CP (half or full threaded) . (Minimum weight 32mm- 45gms/40mm-60 gms) of 32mm bore suitable for wash hand basin complete all as specified and directed by Engr-in-Charge.

S&F in repair Waste coupling of CP (half or full threaded) of 100mm bore suitable for Sink complete all as specified and directed by Engr-in-Charge.

S&F in repair 32 mm dia PVC waste pipe for wash basin /sinks complete all as specified and directed by Engr-in-Charge

S&F in repairs kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers incl bedding in CM 1:4 to dwarf wall or including cast iron cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410mm x 330mm x 160 mm etc complete all as specified and directed by Engr-in-Charge.

S&F in repair plate rack of 1mm thick stainless steel of size 900x600mm with three shelves complete all as specified and directed by Engr-in-Charge.

S & F in repair tubular towel rail 60 cm length of stainless steel 20 mm Dia with brackets type fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engr-in-Charge

S & F in repairs CP shower rose 125mm dia alongwith shower arm complete all as specified and directed by Engr-in-Charge.

S&F in repair 100 mm C.P. grating with openable flap (Min weight 100 gms) ccomplete all as specified and directed by Engr-in-Charge

S&F sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge

S & F 15mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S & F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S & F in repairs 75x125mm dia of PVC (SWR) floor trap, plain with grating incl jointing with solvent cement complete all as specified and directed by Engr-in-Charge

S & F in repairs 125/110 mm dia of PVC (SWR) Gully trap, plain with grating incl jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm bore steel tubing and connection complete all as specified and directed by Engr-in-Charge.

All as per item No above but 20mm bore complete all as specified and directed by Engr-in-Charge

S&F 15mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-Charge.

S&F 20 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth etc brick wall complete all as specified and directed by Engr-in-Charge.

S & F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed by Engr-in-Charge.

S & F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall complete all as specified and directed by Engr-in-Charge.

S & F 75 mm bore PVC (SWR) bends sith complete fittings of any radius complete all as specified and directed by Engr-in-Charge.

S & F 110 mm bore PVC (SWR) bends with complete fittings of any radiuscomplete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) single T with access door of any radius complete all as specified and directed by Engr-in-Charge.

S&F in 110 mm bore PVC (SWR) single Y with access door of any radius complete all as specified and directed by Engr-in-Charge

S & F 110 mm bore PVC (SWR) cowl of any radius complete all as specified and directed by Engr-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed by Engr-in-Charge

Mild steel farmed work as in doors (as in ckowkats) or gates of angle or other section with guest plates rail, brasses rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Gde Fe-290 (Gde E-165) including shop coat of red oxide including prepration of surface before fixing complete all as specified and directed by Engr-in-Charge.

S & F 35 mm thick flush shutters, board solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr-in-Charge.

S&F 35 mm thick 2nd class hard wood (Hollock/Sal/Bijasal), locally febricated glazed skeleton door shutters open rebated and prepare to receive glass, gauge (without sash bars) edges of framing plain chamfered or rounded, fitted with cut including mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I section 8, clause No 8.24 (a) complete all as specified and directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tack or galvanised wire staples complete all as specified and directed by Engr-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 174 of SSR 2020 (Part-II)

S & F Solid PVC door frame for PVC doors, Kitchen cabinet of size 50mm x 47mm made out of 5mm PVC sheet reinforced with MS square tube, as shown on drawings as per manufacturers specification complete all as specified and directed by Engr-in-Charge

S & F PVC door( back side) stopper 75mm long complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-in-Charge

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-Charge

S&F Floor door stopper 150 mm long of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed by Engr-in-Charge

S & F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

S&F 125mm long aluminium anodised Hasp and Staple, safety type including bolt to hinge plate and fixed with screws complete all as specified and directed by Engr-in-Charge.

S & F 40mm width Countinious (Piano) type hinges, mild steel bright finish or electrogalvanised acomplete all as specified and directed by Engr-in-Charge.

S&F 50 mm long mild steel hinges type B-12 complete all as specified and directed by Engr-in-Charge.

S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 290 complete all as specified and directed by Engr-in-Charge.

M & L 18mm thick coloured MDF board fwith hardwood fibres prelaminated both sides including cutting, screwing as in kitchen cabinet, almirah shutter including teakwood liping 6mm thick complete all as specified and directed by Engr-in-Charge.

S & F mild steel 40mm dia decorative knob for kitchen cup board complete all as specified and directed by Engr-in-Charge.

S & F Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed by Engr-in-Charge

Eco-4000 Series windows fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections shoulld be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead shoulld be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window should be provided with grill made of 10mm sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws.

Eco-4000 Series Ventilator fabricated from roll formed sections made of Galvanized steel colour coated/powder coated (Base steel as per IS 513"D" quality, galvanized as per IS 277 with finc of 120 gms/ sqm) with total coated thickness of 0.60mm. Sections shoulld be with primer coat of epoxy primer of 5-7 microns, or powder coated with pure polyester powder up to 50-60 microns thick. Section for frame should be of 72mmx50mm, section for mullion should be of 72mm x50mm, section for shutter frame should be of 47mmx20mm, section for fixed glass bead shoulld be of 12mmx12mm and section for fly mesh shoulld be of 40mmx20mm. Each glazed shutter and mesh shutter shoulld be provided with SS pivot hinges-1 set sec color handle and stay. Each glazed shutter and fixed glass portions should be provided with a glass of 5mm plain float glass. Mesh shutter should be provided with stainless steel 32 guage fly mesh of 304 grade with 144 holes per sq.In. Window should be provided with grill made of 10mm sq MS bars welded to at 150mm centre to centre, 6mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with screws.

M&L Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, alusters, nosing to steps ncluding embeding in concrete and screwing etc. wind ties for roof including securing oltsposts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charged.

M&L 1st class hardwood of size 100x75mm Handrails rounded or shaped with splayed faces in straight lengths complete all as specified and directed by Engr-in-Charge

S & F GI wire 3 mm nominal dia of wire fixed with 20mm mesh with fabrication complete all as specified and directed by Engr-in-Charge

S&F in repairs stainless steel drapery rods, 25mm internal diameter including decoratine type brackets fixing arrangement with drilling holes in walls with brackets including decorative Knob etc complete all as specified and directed by Engr-in-Charge.

M&L for applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer including preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth complete all as specified and directed by Engr-in-Charge.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10 cm width or girth, not otherwise described ccomplete all as specified and directed by Engr-in-Charge

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed by Engr-in-Charge

S & F 20mm dia stainless steel pipe for cupboard complete all as spd and dir by Engr-in-charge.

S & F 20mm stainless steel bracket complete all as spd and dir by Engr-in-charge.

Providing Acrylic plastic number plate of size 300mmX 300mm X 3mm and writing building No. of height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws complete all as specified and directed by Engr-in-Charge.

Providing Acrylic plastic number plate of size 200mmX 200mm X 3mm and writing Qtr No. of height 10 to 15 cm in any style (bold/italic) and fixed to wall with screws complete all as specified and directed by Engr-in-Charge

Cleaning of roughened surface of sunken floor by brushing with wire brush to remove all dirt and applying a coat of cement slurry with 3.00 kg of cement per sqm and rendering 15mm thick in CM 1:3 using WPC finished rough (Sunken floor/Wall) and then applying two course treatment as follow:- (i)M & L three coat of waterproofing solutions smartcare damp proof ultra an innovative fiber reinforced elastomeric liquid which provide the ultimate waterproofing cover of 2.32sqm/Liter with 10 years of waterproofing warranty complete all as specified and directed by Engr-In-Charge. (ii) 40mm bore GI pipe for Spout pipe length 0.75m.

M & L for broken bricks loose filling with aggregates of gauge 40 to 80mm in sunken protion complete all as spd and dir by Engr-in-charge.

M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed in neat cement slurry and pointed in gray pigment cement and pigments neat cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L two coat of Dr fixit Bitufix is applied 4 sqm/ltr a coat, the film thickness achieved will be 125 micron. Further coat shall be applied only after the previous coat dries off completely. Dr fixit bitufix is an emulsified thixotropic bitumen protective coating. The coating dries to form a black flexible protective film. The finished film forms a tough barrier to vapor transmission. Resists the attack of salts like chlorides and sulphates that are present in the soil.

Cutting the roots of trees from the brick walls/stone wall made in cm exc half and not exc one brick thick and making good the disturbed surfaces including coating of paving hot bitumen to arrest further growth to the roots including repair existing surfaces with cm 1:3 or PCC 1:2:4 complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc by cement/ colour /plaster to match with the existing location spot complete all as specified and directed by Engr-in-Charge

M&L for point wiring concealed type with 1.50sqmm PVC FRLS insulated, unsheathed, single core, multi stranded copper conductor cable 1100 volts grade including 1.5sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and Including rigid PVC conduit medium grade, concealed on wall portion and with on steel structural truss/ RCC roof ceiling portion surface type fixed with saddles, screws as per Engr practices of suitable size but not less than 25 mm bore with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodized steel box painted with one coat of red oxide primer including 3.0 mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for the one light/ fan/street/bell point controlled by 1 one way switch 5/6 Amps complete all as specified and directed by Engr-in-Charge.

All as per item No-2 here in before but one light point controlled by two nos 2 way switches complete all as specified and directed by Engr-in-Charge.

All as per item No-2 here in before but One socket outlet 5/6 Amps on independent bd but not below the switch board controlled by one switch complete all as specified and directed by Engr-in-Charge

All as per item No-2 here in before but One socket outlet 5/6 Amps controlled by one switch on same board with other switches complete all as specified and directed by Engr-in-Charge

All as per item No-2 here in before but one socket out let 3/5 pin, 5/6 Amps controlled by one 1way switch on independent board but below the switch board of light points in same vertical plane complete all as specified and directed by Engr-in-Charge.

All as per item No-2 here in before but using 2.5 sqmm PVC FRLS insulated stranded copper conductor cable and for one socket out let 3/6 pin, 15/16 Amps controlled by one 1 way switch on independent board complete all as specified & directed. NOTE-For item no 2 to 7 -: (i)The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillers etc for concealing the conduits to required depth & making good the disturbed surfaces in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at RCC Columns/Beams/Ceilings etc shall be in surface conduit of suitable size fixed on surface with using PVC rawl plug and provision of covering terminal boxes/junction boxes of any shape and size with 3 mm thick bakelite laminated sheet fixed with suitable GI screws and cup washers. (ii) Fittings like switches,sockets,regulators,lamp holders,light fittings shall be measured and paid for separately under appropriate item of schedule A. (iii)The size of conduits shall be determined on permissible no of runs of wires as specified in SSR part-I clause 19.125 (B).However minimum size of conduit shall be 20 mm dia (medium grade)

Supply and fix switch piano, flush type, single pole, 5/6 Amps one way, 230 volts complete all as specified and directed by Engr-in-Charge

S & F switch piano, flush type single pole, two way 5 Amp 230 volts complete all as specified and directed by Engr-in-Charge

Supply and fix switch piano, flush type, single pole, 15/16 Amps one way, 230 volts ccomplete all as specified and directed by Engr-in-Charge

Supply and fix socket outlet, 5/6 Amps, flush type, 5 pin 230 volts complete all as specified and directed by Engr-in-Charge

Supply and fix socket outlet, multi-purpose 3 pin 5/6 Amps and 3 pin 15/16 Amps complete all as specified and directed by Engr-in-Charge

S&F for ceiling rose surface bakelite 62.5 x 25 mm size 3 terminals complete all as specified and directed by Engr-in-Charge

S&F switch, bell push button, single pole, 5/6 Amps, one way, 230 Volts complete all as specified and directed by Engr-in-Charge

Supply and fix electrical bell model city ding dong (Ding dong type) AC, 230 Volts complete all as specified and directed by Engr-in-Charge

Supply and fix lamp holder insulated body with back plate for batten fitting complete all as specified and directed by Engr-in-Charge

Supply & fix in replacement, single pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB SP of capacity 20 Amps 240 volts IK-08 As per IEC 61439-3 complete all as specified and directed by Engr-in-Charge.

Supply & fix commissioning and testing of complete power cum starter unit compressing of ON/OFF switches socket 3 pin socket outlet with plug top modular type made out of white polycarbonate, fire retardant, UV stabilized power unit internally pre-wired with suitable size copper conductor cable with overload protective device (MCB) complete unit fixed in single polycarbonate housing with inlet & outlet cable port suitable for AC & geyser operated at single phase, 240 volts, 50 Hz AC supply of capacity 20 Amps load bearing capacity complete all as specified and directed by Engr-in-Charge

Supply and fixing LED Bulb 15 watt, single phase, 230 Volts AC supply suitable for lamp holder complete all as specified and directed by Engr-in-Charge.

S&F in replacement LED Batten surface/wall mounted with specially designed powder coated aluminium housing,high optically efficient polycarbonate diffuser,in built electronic driver duly wired up to terminal block,power consumption<20W,luminaire lumen >2000 lm,system efficiency of >120 lumens/W,LED make Nichia/Cree/Everlite/Eclison/Osram/lumiled,with LED binning as per ANSI Bin C78.377A,photo biological safety report as per IEC 624718& electrical insulation class 1 Ingress protection IP 20,clor rendering index CRI> 80 ,temp range 0 to 450 C ,driver efficiency >85% Power factor >0.9 THD <20% as per IEC 61000-3-2 ,color temp -6500K,Surge protection 2.5 KV,50000 burning hrs (min) as per L7O criteria,two stages isolated constant current operated driver with range 150-270 V AC and safety extra low voltage safe level< 60 V DC as per IEC standard with LM70 & LM 80 certification.

S&F in replacement Mirror light Decorative ultra slim square profile liner LED lighting fixture with extruded polycarbonate body with Minimum 8 Watt & Maximum 15 Watt LED warm white in colour with a nominal system output of 120 lum/watt(min) with PF not less than 0.9 complete all as specified and directed by Engr-in-Charge

Supply and fixing in replacement LED security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-in-Charge

S & F in replacement LED light fitting 1x9 W/1X10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable, power consumption < 10 W and system efficiency > 100lm /W, of suitable size complete all as specified and directed by Engr-in-Charge.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor .

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 6.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length. Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length.

Taking down distribution boards any size any type including MCB TPN/SPN/SP/MCCB etc and making good the disturbed surfaces complete all as specified and directed by Engr-in-Charge.

Supply and fix MCB DB vertical type 4 way VTPN sheet metal enclosure 415 volts with 100 Amp fully insulated standard copper bus bar for each face & surrounded with neutral bars and two common neutral bar, two earth bar including cable ties for cable management suitable for housing MCCB TPN 415 Volts as incomer, IP-43, IK-09 as per IEC 61439-3 with metal doors all enclosed on standard steel sheet flush mounting type double door factory fabricated complete without MCB & MCCB but with enclosure blank plate complete all as specified and directed by Engr-in-Charge .

Supply and fix MCB DB sheet metal enclosure factory fabricated double door SPN 12 way with 100 amps rated copper bus bar 240 volts IP-43, IK-09 with metal doors ccomplete all as specified and directed by Engr-in-Charge.

S&F MCCB of rating 100 Amp, 4 pole, 415 V, AC fixed type with breaking capacity 25 KA DPX³ 160 type, as per ICE- 60947-1 Ics 100% of Icu, Adjustable tripping: 0 - 0.3 - 1 - 3s with adjustable 70% to 100% and thermal magnetic release to be fixed in existing LT panel for taking In coming electric connection for VTPN DB complete all as specified and directed by Engr-in-Charge.

Supply and fixing MCB SPN 240V, 50 Hz, 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity 40 to 63 Amp rating in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-in-Charge.

Supply & fix in MCB SP, 40 Amps, 'C' Curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified and directed by Engr-in-Charge.

Supply & fix MCB SP, 6 to 32 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified and directed by Engr-in-Charge.

Supply and fix electric water heater, of capacity 25 Ltrs vertical storage type, outer body of the heater is made with tough ABS material with special inner tank coating that prevents corrosion and rusting and results in a long tank life energy-efficient and Heating Element upto 2 KW (copper tube)-Spiral Type Multiple safety systems for protection against dry heating, overheating and overpressure, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece (hot & cold of length uoto 450 mm long with to be fixed on wall with fastener mild steel 100 mm long x 10 mm dia with expansion type split pin and bolts complete for hanging of geyser complete all as specified and directed by Engr-in-Charge

S&F iron metal body heavy duty exhaust fan 300mm sweep, double ball bearing, copper wound, with louvers, 230 volts, 50 Hz, including electrically connecting from ceiling rose to fan connector with 0.5 Sqmm stranded copper conductor 3 core flexible cable cord complete all as specified and directed by Engr-in-Charge

Supply and fix PVC body fresh air circulator of size 225 mm sweep, with PVC louvers, operated at 230 Volts 50 Hz, 1350 to 1400 RPM with 3 core flexible copper conductor cable cord of size 0.75 Sqmm from fan to ceiling rose complete all as specified and directed by Engr-in-Charge

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

M & L in repair earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanized steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe upto 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Looose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1.

M&L for electrically disconnecting and taking down existing ceiling/Exhaust fans from any height or in any position from existing bldg and keeping in safe custody and submit it after necessary repair/ servicing & painting with one coat of synthetic enable paint including replacement of three cor flexible copper conductor cable from ceiling rose to fan connector block of size 0.75 Sqmm and hanging fan clamps, nuts, bolts and rubber reel bush etc & testing for proper functioning complete all as directed at site by Engr-in- Charge.

Supply & Laying in replacement, testing ,cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 50 Sqmm 3½ core complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr deep in soft/loose/ soil for taking out/laying CI/GI pipe line and getting out soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25 cm thick layers complete all as specified and as directed by Engineer-in-Charge.

Removal of excavated material n.exc 50 mtr away and depositing where directed at a level n.exc 1.5 mtr above from starting point complete all as specified and as directed by Engineer-in-Charge.

Supplying and laying un-reinforced precast concrete cable cover LV type-I flat size 250 mm x 150 mm x 40 mm in trenches for protection of cable complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning dry fine for cable cushioning below and above the cable complete all as directed at site by Engr- in-Charge.

Supply and fixing in replacement GI Pipe 40mm Light grade , for cable protection laid in trench under road or path or fixed on pole or wall with clamps with all fittings complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement gun metal gate valve of size 20mm bore with iron wheel head screwed both ends for iron pipe and fixed of following sizes complete all as specified and directed by Engr-in-Charge.

S & F in replacement galvanized iron tubes, medium grade of size 20 mm bore fixed to wall, ceiling and laid under floor complete all as specified and directed by Engr-in-Charge.

S & F in replacement galvanized iron tubes, medium grade of size 40 mm bore fixed to wall, ceiling and laid under floor complete all as specified and directed by Engr-in-Charge

M&L for Electric circuits for size of 1.5 sqmm copper FRLS wire for inverter in existing conduit complete all as specified and directed by Engr-in-Charge

Supply and fix water proof plastic box 1 module/ 3 module with switch or/and socket use in outdoor lighting/Garden etc. for 6A switch. complete all as specified and directed by Engr-in-Charge

M/S A A DRILL EXPERT (BID ID -3134136)

ASHISH SHARMA (BID ID -3134382)

VARDMAN ENTERPRISES (BID ID -3133805)

M/s Rahul Kumar Agrawal (BID ID -3132915)

SHANTI CONSTRUCTIONS (BID ID -3133921)

M/S Chadha Brothers (BID ID -3134078)

M/s Kok Singh Sisodia (BID ID -3134015)